1-20-SJ3000-RED - 3M (TC) - Datasheet.Live

Reclosable Fastener SJ3000

Thin Hook and Loop Back-to-Back

Pr oduct Information September, 2010

Pr oduc t Descr ipt ion 3M™ Reclosable Fastener SJ3000 is a thin back-to-back fastener that offers closure

alternatives to plastic wire, tape, string, rubber bands and other types of closure

systems used to secure bundles of items. Reclosable Fastener SJ3000 offers design

flexibility, fast product assembly and improved product performance in many

applications.

One side of the thin fastener strip is covered with tiny translucent polypropylene

hooks, approximately 1400 per square inch (220/sq. cm.). These hooks can engage

with thousands of soft, pliable, thin polyester loops on the reverse side providing

for a limited number of openings and closings (cycles). The thin loop is designed to

easily engage with reclosable fastener SJ3000 hook and possibly other small hooks.

The hook may also engage with many other loop materials. This forms a quick

fastening attachment system. Simply pull the strips apart to disengage.

Pr oduc t Cons truc tion Note: The following information is not product r elease requirements, nor product specification

limits. Rather, this data represents typical performance using standard test methods. This

is intended for use as a guide to assist in selection of 3M™ Reclosable Fasten ers for further

evaluation. Customer specificat ions should not be based solely on the data presented in

this document. It is recommend ed that the customer test the product under ex pected u s e

conditions in the desired application to determine actual suitability and performance.

Fastener Product 3M™ Reclosable Fastener SJ3000

Material of Construction

Hook Polypropylene

Loop Polyester

Adhesive None

Standard Colors Red, Black, White

Thickness - unmated 0.027" (0.69 mm)

- engaged 0.061" (1.55 mm)

Weight oz/in2 (g/cm2) 0.005 oz/in2 (0.021 g/cm2)

Thickness was measured using a 0.5" diameter pressure foot supporting a 34

gram

weight. Actual thickness

will decrease when a load is applied or the product

compressed and will increase if a load is

removed.

3M™ Reclosable F astener SJ3000

Thin Hook and Loop Back to Back

Typical Performance

Properties and

Characteristics

Unless stated, typical system performance characteristics were measured under controlled laboratory

conditions of 72°F ± 5°F (22°C ± 2.7°C) and 50% ± 10% relative humidity. The user should evaluate

products in the actual application to ensure suitable performance for the intended use.

Fastener Product 3M™ Reclosable Fastene r SJ 3000

Performance tests are determined b y measuring the performance of the

entire

reclosable

fastener when

the hook on one side is engaged to the loop on the other side of the fastener.

CLOSURE SHEAR (Rigid to Rigid Substrates) PoundsF/inch2

(Newtons/cm

)

Dynamic Shear (1/2" x 1" overlap) 31 (21.6)

Static Shear Holding Strength Holds 1.1#/in2 (77.5 grams/cm2) fo r ind ic ate d

time

and

temperature

100°F

(38°C)/100%

R.H.

10,000

minutes

120°F (49°C) 10,000 minutes

158°F (70°C) 10,000 minutes

200°F (93°C) 10,000 minutes

PEEL at 12 inches (305mm) per minute PoundsF/inch width

“T” Peel Force (Flexible to Flexible) 2.2

90° Peel Force (Flexible to Rigid) - Average 3.0

CLOSURE CYCLE LIFE 15

Cycle life is the number of cycles (openings and closings) that the fastener is subjected to while maintaining

50% or greater of the 2nd closure peel values. Initial peels are slightly higher

SHELF LIFE T wenty four months from date of

manufacturin g

when stored in original packaging at 70°F ± 10°F

(21°C ± 5.5°C) and 50% ± 10% relative humidity.

Note: Long Term Static Load: Conditions such as temperature variations,

engagement

area, closure pressure

and vibrations or side to side movement afte r engagement

exposure to prolonged periods of moisture,

ultraviolet or other environmental factors

can

affect the closure strength and long te r m static load performance.

Reclosable

fasteners

may slip or creep in the direc tion of the static load fo rces when subjected to static

loads

temperatures or weights greater than indicated. The user is respons ible for

designing

the amount of fastening

area based upo n the specific conditions for the application.

Four

square inches of fastening area per pound

(57.3 sq. cm/kilogram) of static load

suggested as a starting point for such

evaluations.

Additional

Performance

Characteristics

Chemical Resistance: The polypropylene hook and polyester loop resist incidental attack

by most common solvents and alkaline solutions. Acid solutions may cause deterioration

of the loop. Small amounts of oils, mold release agents would not be expected to cause

performance issues when in contact with 3M™ Reclosable Fastener SJ3000, except for

the possible difficulty in starting a wrap.

Plasticizer Resistance: The polypropylene hook and polyester loop should have good

resistance to direct contact with most plasticized materials.

Flammability Resistance: Reclosable Fastener SJ3000 will not pass common

flammability tests when tested unattached to an substrate. If you need reclosable

fasteners to meet many of the standard flammability tests (such as FAR 25.853,

FMVSS-302), you may want to consider using 3M™ Reclosable Fasteners

SJ3418FR/19FR, SJ3518FR/19FR and SJ3486FR/87FR.

Water (Humidity) Resistance: Closure strength should be minimally affected by high

humidity conditions.

- 2 -

3M™ Reclosable F astener SJ3000

Thin Hook and Loop Back to Back

Attachment Techniques The following information is intended to assist the designer considering the use of

3M™ Reclosable Fastener SJ3000. It is recommended that the user evaluate 3M

products to determine whether they are fit for a particular purpose and suitable for

the user’s materials, method of application and desired end use.

Reclosable fastener SJ3000 can easily be cut to desired dimensions and shapes per

application need. The product is often used in rectangular strips 1/2" width by

appropriate length required to wrap at least one and one half times around item(s)

being bundled plus a 0.5 inch (1.3 cm) tab or flag. A common formula for

determining desired length is:

(Bundle or item circumference in inches ) x (1.5) + 0.5 inch

(Bundle or item circumference in centimeters) x (1.5) + 1.3 cm

While reclosable fastener SJ3000 is more flexible than many common bundling

materials, care should be exercised in wrapping bundles that have very small

diameters, lest flagging of the end will occur, possibly leading to premature

disengagement. To prevent premature or undesirable flagging a small quantity of a

curable liquid adhesive, hot melt, epoxy or similar material could be applied

joining the exposed end of the fastener with the underlying fastener. This method

will make it more difficult to easily disengage the fasteners.

Rounding the corners can reduce the possibility of edge lifting or flagging while

improving the overall appearance of the fastener on the finished product.

Mechanically securing the corners of the fastener with rivets, staples, screws, etc.

may reduce the closure performance.

Material Surface Preparation: Textured or rough surfaces, especially those that

may engage with a hook or loop can allow easier starting of a wrap around an

object(s). Very smooth surfaces may cause slippage or difficulty in starting the

wrap. In that case the surface could be roughened, or small strips of 3M™

Reclosable Fasteners SJ3506 or SJ3507 could be first applied to the surface.

Surfaces containing oils, mold release agents or other coatings and materials that

can create a slippery surface should be avoided due to possible difficulty in getting

the wrap started, or slipping in usage. It is recommended to remove any surface

contaminants that may cause slippage or problems with starting the wrap by using a

method suited for the type and quantity of surface slip agent present.

Engagement Procedure: Highly porous, soft or fragile materials such as some

vegetables or foam materials may crush or collapse if too high of a pressure is

applied during bundle wrapping. Approximately 2 pounds per inch width (0.4

kilograms per centimeter width) is required for engaging reclosable fastener

SJ3000 to itself. For all applications, it is important to ensure that an acceptable

amount of overlap at the end of the fastener is provided to prevent premature

unwrapping or flagg ing .

The most common technique for attaching reclosable fastener SJ3000 is to wrap

the product upon itself, forming the closure system to bundle items together,

provide surface protection or to secure items during transport. To ensure full

fastener strength the fastener should be completely overlapped, not spiral would

unless the reduced engaged surface area is taken into account.

- 3 -

3M™ Reclosable F astener SJ3000

Thin Hook and Loop Back to Back

Application Ideas 3M™ Reclosable Fastener SJ3000 can provide a firm closure system used to secure

bundles of items or hold items in packaging during shipping or storage. Additionally ,

this product, in combination with 3M™ Reclosable Fasteners SJ3506 or SJ3507

could be used as a removable roll wrap for starting pull through of textile and similar

materials. W rapping a variety of surfaces can provide a removable protection.

Because product performance will depend on actual conditions within any specific

application, it is essential that the user evaluate the 3M product to determine

whether it is fit for a particular material purpose and suitable for the user’s method

of application.

Reclosable Fastener SJ3000 can be evaluated for use in:

Securing wire bundles Labeling garden plants/temporary identifica tion

• During assembly, inspection, repair • Writ e-on loop for weather resistant label

• Abrasion protection (loop against wires) Box Closures

Securing light-weight items in shipping containers

Certification/

Recognition MSDS: This product is not subject to the MSDS requirements of the Occupational Safety and Health

Administration’s Hazard Communication Standard, 29 C.F.R. 1910.1200(b)(6)(v) and therefore 3M has

not prepared a MSDS for this product. However, use or processing of the product in a manner not in

accordance with the directions for use may affect its performance and present potential health and

safety hazards.

TSCA: This product is defined as an article under the Toxic Substances Control Act and therefore, it is

exempt from inventory listing requirements.

Technical Information The technical information, recommendations and other statements contained in this document are

based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such

information is not guaranteed.

Product Use Many facto rs beyond 3M’s control and uniquely within user’s knowledge and control can affect the use

and performance of a 3M product in a particular applicat ion. Given the variety of f actors that can affect

the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and

determining whether it is fit for a particular purpose and suitable for user’s method of application.

Warranty,

Limited Remedy,

and Disclaimer

Unless an additional warranty is specifically stated on the applicable 3M product packaging or product

literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time

3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY

OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.

If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s

option, replacement of the 3M product or refund of the purchase price.

Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product,

whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted,

including warranty, contract, negligence or strict liability.

ISO 9001:

2000 -

ISO/TS 16949:2002

This Industrial Adhesives and Tapes Division product

was

manufactured under a 3M quality s ystem

registered to ISO

9001:

2000 and ISO/TS 16949:2002

standards.

Industrial Adhesives and Tapes Division

3M Center, Building 225-3S-06

St. Paul, MN 55144-1000

800-362-3550 • 877-369-2923 (Fax)

www.3M.com/industrial

Recycled Paper

40% pre-consumer

10% post-consumer

- 4 -

3M is a trademark of 3M Company

Printed in U.S.A.