AMIS-710239-A3: 200dpi CIS Module Data Sheet 1.0 General Description The AMIS-710239-A3 (PI239MC-A3-R) is a contact image sensor (CIS) module. It is a long contact image sensor, which uses MOS image sensor technology for high speed performance. The AMIS-710239-A3 is suitable for scanning A3 size (307mm) documents with eight dots per millimeter (dpm) resolution. Hence, there are 38 AMIS-720233 (PI3033B) image sensors in the module, providing a total of 2432 pixels in a sequence. The sensors are 200 dots per inch (dpi) solid-state line imaging array, also a product of AMI Semiconductor. Applications include document scanners, mark readers and other office automation equipment. 2.0 Key Features * * * * * * * * * Light source, lens and sensor are integrated into a single module 8dpm resolution, 307mm scanning read length High speed page scan - up to 490sec/line @ 5MHz pixel rate Wide dynamic range One analog output Super super Red (630nm) LED light source Compact size 20.5mm x 21.5mm x 324mm Low power Light weight 3.0 Functional Description The AMIS-710239-A3 imaging array consists of 38 sensor chips in the module, which are sequentially cascaded to provide 2432 photodetectors with their associated multiplex switches and a digital shift register, which controls its sequential readout. Mounted in the module is a one-to-one graded indexed micro lens array, which focuses the scanned documents to image onto its sensing plane. The on-board amplifier processes the video signal to produce a sequential stream of video at the video output pin. Illumination is accomplished by means of an integrated LED light source. All components are housed in a small plastic housing which has a cover glass acting as the focal point for the object being scanned and protects the imaging array, micro lens assembly and LED light source from dust. I/O to the module is the 10-pin connector, located on one end of the module. The cross section of the AMIS710239-A3 is shown in Figure 1 and the block diagram in Figure 2. AMI Semiconductor - Aug. 06, M-20610-001 www.amis.com 1 AMIS-710239-A3: 200dpi CIS Module Figure 1: AMIS-710239-A3 Cross Section Figure 2: AMIS-710239-A3 Module Block Diagram AMI Semiconductor - Aug. 06, M-20610-001 www.amis.com 2 Data Sheet AMIS-710239-A3: 200dpi CIS Module Table 1: Pin Configuration Pin Number 1 2 3 4 5 6 7 8 9 10 Symbol Vout Gnd Vdd (+5V) Vn (-5V to -12V) Gnd SP Gnd CP GLED VLED Data Sheet Names and Functions Analog video output Ground; 0V Positive power supply Negative power supply Ground; 0V Shift register start pulse Ground; 0V Sampling clock pulse Ground for the light source; 0V Supply for the light source 4.0 Absolute Maximum Rating Table 2: Absolute Maximum Rating Parameter Power supply voltage Input clock pulse (high level) Input clock pulse (low level) Symbol Vdd Idd Vn In VLED ILED Vih Vil Maximum Rating 7.5 90 -15 15 5.5 1200 Vdd - 0.5V -0.6 Units V ma V ma V ma V V Note: These parameters are absolute maximums and are not for operation. Extended operation may cause catastrophic failure. 5.0 Operating Environment Table 3: Operating Environment Parameter Operating temperature Operating humidity Storage temperature Storage humidity AMI Semiconductor - Aug. 06, M-20610-001 www.amis.com Symbol Top Hop Tstg Hstg Range 0 to 50 10 to 85 -25 to +75 5 to 95 3 Units C % C % AMIS-710239-A3: 200dpi CIS Module Data Sheet 6.0 Electro-Optical Characteristics (25C) Table 4: Electro-optical characteristics at 25C. Parameter Symbol Number of photo detectors Pixel-to-pixel spacing (1) Line scanning rate Tint (2) Clock frequency f (3) Bright output voltage Video output (4) Bright output non-uniformity Up (5) Adjacent pixel non-uniformity Uadj (6) Dark non-uniformity Ud Dark output voltage Vd (7) Modulation transfer function MTF Notes: (1) (2) (3) (4) (5) (6) (7) (8) (9) Parameter 2432 125 490 5 1.0 +/- 0.1 <+/-30 <25 <100 <200 >50 Units Elements m sec MHz V % % mV mV % Note @ 5MHz clock frequency @ Tint=490us See Note 7 for MTF & DOF Tint: line scanning rate or integration time. Tint is determined by the interval of two start pulses (SP). The module shall be tested at 490us, but it will operate to us with a clocking speed of 5.0MHz. f: main clock frequency. The module was tested at 5.0MHz, but electrically it reliably operates above 5.0MHz. Vpavg = Vp(n)/2432 Up = [(Vpmax - Vp) / Vp] x 100% or [(Vp - Vpmin) / Vp] x 100% Upadj = MAX[ | (Vp(n) - Vp(n+l) | / Vp(n)] x 100% Upadj is the non-uniformity percentage pixel to pixel (6) Ud = Vdmax - Vdmin Vdmin is the minimum output on a black document (O.D. = 0.8) Vdmax: maximum output voltage on a black document (O.D. = 0.8) (7) MTF = [(Vmax - Vmin) / (Vmax + Vmin)] x 100 [%]. The DOF range is defined with the MTF. MTF is a measure at the glass surface and at 0.4mm from the glass > 50 percent and peaks at approximately a mid-point of 0.2mm. Vmax: maximum output voltage at 50lp/inch (at 1/2 of the optical Nyquest frequency) Vmin: minimum output voltage at 50lp/inch O.D. = optical density lp / inch: line pair per inch 7.0 Recommended Operating Conditions (25C) o Table 5: Recommended Operating Conditions at 25 C Item Symbol Power supply Vdd Vn. VLED Idd In ILED Input voltage at digital high Vih Input voltage at digital low Vil Clock frequency f Clock pulse high duty cycle Clock pulse high duration (3) Integration time Tint Operating temperature Top Notes: (1) (2) (3) Min. 4.5 -4.5 4.5 66 5 550 Vdd-1.0 0 5.0 www.amis.com (2) Max. 5.5 -12 5.5 86 15 1200 Vdd 0.6 5.5 25 50 490 25 Will be tested at 5.0MHz and 490us. Will be used as a test for typical value. Proposed tint (min.) is the lowest line integration time available at a 5.5MHz clock rate. AMI Semiconductor - Aug. 06, M-20610-001 (1) Mean 5.0 -5 5 76 10 800 Vdd-0.5 4 5000 50 Units V V V ma ma ma V V MHz % ns s C AMIS-710239-A3: 200dpi CIS Module Data Sheet 8.0 Switching Characteristics (25C) Figure 3: Clock and Start Pulse Timing Diagram The switching characteristics for the I/O clocks are shown in Figure 3. The corresponding definitions for the timing symbols are given in Table 6. Table 6: Symbol Definition for Figure 3 (Timing Diagram) Item Symbol Clock cycle time to Clock pulse width tw Clock duty cycle Prohibit crossing time of SP tprh Data setup time tds Data hold time tdh Signal delay time tdl Signal settling time tsh Min. 0.2 50 25 15 20 20 50 120 Note: These are the proposed times. There may be minor changes in actual implementation. AMI Semiconductor - Aug. 06, M-20610-001 www.amis.com 5 Typ. Max. 4.0 75 Units s ns % ns ns ns ns ns AMIS-710239-A3: 200dpi CIS Module Data Sheet 9.0 AMIS-710239-A3 Module Mechanical Dimensions The sketch of this module is provided as a pictorial of the module size and structure. A detailed drawing is available upon request. Figure 4: Module and its Mechanical Dimensions AMI Semiconductor - Aug. 06, M-20610-001 www.amis.com 6 AMIS-710239-A3: 200dpi CIS Module Data Sheet 10.0 Company or Product Inquiries For more information about AMI Semiconductor, our technology and our product, visit our Web site at: http://www.amis.com North America Tel: +1.208.233.4690 Fax: +1.208.234.6795 Europe Tel: +32 (0) 55.33.22.11 Fax: +32 (0) 55.31.81.12 Production Technical Data - The information contained in this document applies to a product in production. AMI Semiconductor and its subsidiaries ("AMIS") have made every effort to ensure that the information is accurate and reliable. However, the characteristics and specifications of the product are subject to change without notice and the information is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify that data being relied on is the most current and complete. AMIS reserves the right to discontinue production and change specifications and prices at any time and without notice. Products sold by AMIS are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMIS makes no other warranty, express or implied, and disclaims the warranties of noninfringement, merchantability, or fitness for a particular purpose. AMI Semiconductor's products are intended for use in ordinary commercial applications. These products are not designed, authorized, or warranted to be suitable for use in life-support systems or other critical applications where malfunction may cause personal injury. Inclusion of AMIS products in such applications is understood to be fully at the customer's risk. Applications requiring extended temperature range, operation in unusual environmental conditions, or high reliability, such as military or medical life-support, are specifically not recommended without additional processing by AMIS for such applications. Copyright (c) 2006 AMI Semiconductor, Inc. AMI Semiconductor - Aug. 06, M-20610-001 www.amis.com 7