ASM2I99456 June 2005 rev 0.2 3.3V/2.5V LVCMOS Clock Fanout Buffer Features Configurable specified for the extended temperature range of -40 to 10 outputs LVCMOS Clock distribution buffer Compatible to single, dual and mixed 3.3V/2.5V 85C. The ASM2I99456 is a full static design supporting clock Voltage supply frequencies up to 250 MHz. The signals are generated and Wide range output clock frequency up to retimed on-chip to ensure minimal skew between the three 250MHz output banks. Designed for mid-range to high-performance telecom, networking and computer applications Supports high-performance differential clocking by 2.5V or 3.3V supporting mixed voltage applications. The applications FSELx pins choose between division of the input reference Max. output skew of 200pS frequency by one or two. The frequency divider can be set (150pS within one bank) individually for each of the three output banks. The Selectable output configurations per output bank Tristatable outputs 32 LQFP and TQFP Packages Ambient Operating temperature range of -40 to 85C Each of the three output banks can be individually supplied ASM2I99456 can be reset and the outputs are disabled by deasserting the MR/OE pin (logic high state). Asserting MR/OE will enable the outputs. All control inputs accept LVCMOS signals while the outputs Pin and Function compatible to MPC9456 provide LVCMOS compatible levels with the capability to drive terminated 50 transmission lines. The clock input is Functional Description The ASM2I99456 is a 2.5V and 3.3V compatible 1:10 clock distribution buffer designed for low-Voltage mid-range to high-performance telecom, networking and computing applications. Both 3.3V, 2.5V and dual supply voltages are supported for mixed-voltage applications. The ASM2I99456 offers 10 low-skew outputs and a differential LVPECL clock input. The outputs are configurable and support 1:1 and 1:2 low voltage PECL compatible for differential clock distribution support. Please consult the ASM2I99446 specification for a full CMOS compatible device. For series terminated transmission lines, each of the ASM2I99456 outputs can drive one or two traces giving the devices an effective fanout of 1:20. The device is packaged in a 7x7 mm2 32-lead LQFP and TQFP Packages. output to input frequency ratios. The ASM2I99456 is Alliance Semiconductor 2575, Augustine Drive * Santa Clara, CA * Tel: 408.855.4900 * Fax: 408.855.4999 * www.alsc.com Notice: The information in this document is subject to change without notice. ASM2I99456 June 2005 rev 0.2 Block Diagram Bank A PCLK CLK 0 CLK/ 2 1 25K PCLK QA0 QA1 VCC/2 QA2 25K Bank B QB0 0 QB1 1 QB2 FSELA QC0 25K Bank C FSELB QC1 0 25K 1 FSELC QC2 25K MR/OE QC3 25K ASM2I99456 Logic Diagram GND QB0 VCCB QB1 GND QB2 VCCB VCCC Pin Configuration 24 23 22 21 20 19 18 17 VCCB is internally connected to VCC VCCA 25 16 QC3 QA2 26 15 GND GND 27 14 QC2 QA1 28 13 VCCC VCCA 29 12 QC1 QA0 30 11 GND GND 31 10 QC0 MR/OE 32 ASM2I99456 2 3 4 5 6 7 8 NC VCC PECL_CLK PCL_CLK FSELA FSELB FSELC GND 9 1 VCCC 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 2 of 14 ASM2I99456 June 2005 rev 0.2 Table 1. Pin Configuration Pin Number Pin 3 4 5,6,7 32 8,11,15,20,24,27,31 25,29 18,22 9,13, 17 2 30,28,26 I/O Type Function PECL_CLK, PECL_CLK Input LVPECL Differential Clock reference Low Voltage positive ECL input FSELA, FSELB, FSELC Input LVCMOS Output bank divide select input Input LVCMOS Internal reset and output tristate control Supply Negative Voltage supply output bank (GND) Supply Positive Voltage supply for output banks Supply Positive Voltage supply core (VCC) Bank A Outputs MR/OE GND VCCA, VCCB1, VCCC VCC QA0 - QA2 Output LVCMOS 23,21,19 QB0 - QB2 Output LVCMOS Bank B Outputs 10,12,14,16 QC0 - QC3 Output LVCMOS Bank C Outputs 1 NC - - No Connect Note:1 VCCB is internally connected to VCC. Table 2. Supported Single and Dual Supply Configurations Supply voltage configuration VCC1 VCCA2 VCCB3 VCCC4 GND 3.3V 3.3V 3.3V 3.3V 0V Mixed voltage supply 3.3V 3.3V or 2.5V 3.3V 3.3V or 2.5V 0V 2.5V 2.5V 2.5V 2.5V 2.5V 0V 3.3V Note: 1 VCC is the positive power supply of the device core and input circuitry. VCC voltage defines the input threshold and levels 2 VCCA is the positive power supply of the bank A outputs. VCCA voltage defines bank A output levels 3 VCCB is the positive power supply of the bank B outputs. VCCB voltage defines bank B output levels. VCCB is internally connected to VCC. 4 VCCC is the positive power supply of the bank C outputs. VCCC voltage defines bank C output levels Table 3. Function Table (Controls) Control FSELA FSELB FSELC MR/OE Default 0 0 0 0 fQA0:2 = fREF fQB0:2 = fREF fQC0:3 = fREF 0 Outputs enabled 1 fQA0:2 = fREF /2 fQB0:2 = fREF /2 fQC0:3 = fREF /2 Internal reset Outputs disabled (tristate) Table 4. Absolute Maximum Ratings1 Symbol Characteristics Min Max Unit VCC Supply Voltage -0.3 4.6 V VIN DC Input Voltage -0.3 VCC+0.3 V DC Output Voltage -0.3 VCC+0.3 V DC Input Current 20 mA DC Output Current 50 mA 125 C VOUT IIN IOUT TS Storage temperature -40 Condition Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 3 of 14 ASM2I99456 June 2005 rev 0.2 Table 5. General Specifications Symbol Characteristics Min Typ Max Unit VTT Output Termination Voltage VCC /2 MM ESD Protection (Machine Model) 200 V HBM ESD Protection (Human Body Model) 2000 V LU Latch-Up Immunity 200 mA CPD Power Dissipation Capacitance 10 pF CIN Input Capacitance 4.0 pF Condition V Per output Table 6. DC Characteristics (VCC = VCCA = VCCB = VCCC = 3.3V 5%, TA = -40 to +85C) Symbol Characteristics Min VIH VIL Input high voltage Input low voltage VPP Peak-to-peak input voltage PCLK 250 Common Mode Range PCLK 1.1 VCMR1 IIN VOH Input current Typ 2.0 -0.3 2 Output High Voltage Max Unit VCC + 0.3 0.8 V Output Low Voltage ZOUT ICCQ4 Output impedance Maximum Quiescent Supply Current V LVCMOS LVCMOS mV LVPECL VCC-0.6 V 200 A V LVPECL VIN=GND or VIN=VCC IOH=-24 mA3 0.55 0.30 V V IOL= 24mA2 IOL= 12mA 2.0 mA 2.4 VOL Condition 14 - 17 All VCC Pins Note: 1 VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR range and the input swing lies within the VPP (DC) specification. 2 Input pull-up / pull-down resistors influence input current. 3 The ASM2I99456 is capable of driving 50 transmission lines on the incident edge. Each output drives one 50 parallel terminated transmission line to a termination voltage of VTT. Alternatively, the device drives up to two 50 series terminated transmission lines. 4 ICCQ is the DC current consumption of the device with all outputs open and the input in its default state or open 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 4 of 14 ASM2I99456 June 2005 rev 0.2 Table 7. AC Characteristics (VCC = VCCA = VCCB = VCCC = 3.3V 5%, TA = -40 to +85C)1 Symbol Characteristics fref Input Frequency fMAX Maximum Output Frequency VPP Min /1 output /2 output Peak-to-peak input voltage PCLK VCMR3 Common Mode Range PCLK tP, REF Reference Input Pulse Width tr, tf tPLH tPHL tPLZ, HZ PCLK Input Rise/Fall Time tPZL, LZ tsk(O) tsk(PP) Max Unit Condition 0 Typ 2502 0 0 2502 125 500 1000 MHz MHz MHz mV FSELx=0 FSELx=1 LVPECL 1.3 VCC-0.8 V LVPECL 1.4 nS 1.04 Output Disable Time 10 nS nS nS nS Output Enable Time Output-to-output Skew 10 nS 150 200 350 pS pS pS 2.25 nS 200 pS 53 55 % % DCREF = 50% DCREF = 25%-75% 1.0 nS 0.55 to 2.4V CCLK to any Q CCLK to any Q Propagation delay 2.2 2.2 2.8 2.8 4.45 4.2 Within one bank Any output bank, same output divider Any output, Any output divider Device-to-device Skew 5 tSK(P) Output pulse skew DCQ Output Duty Cycle tr, tf Output Rise/Fall Time /1 output /2 output 47 45 50 50 0.1 0.8 to 2.0V Note: 1 AC characteristics apply for parallel output termination of 50 to VTT. 2 The ASM2I99456 is functional up to an input and output clock frequency of 350MHz and is characterized up to 250 MHz. 3 VCMR (AC) is the crosspoint of the differential input signal. Normal AC operation is obtained when the crosspoint is within the VCMR range and the input swing lies within the VPP (AC) specification. 4 Violation of the 1.0nS maximum input rise and fall time limit will affect the device propagation delay, device-to-device skew, reference input pulse width, output duty cycle and maximum frequency specifications. 5 Output pulse skew is the absolute difference of the propagation delay times: | tPLH - tPHL |. Table 8. DC Characteristics (VCC = VCCA = VCCB = VCCC = 2.5V 5%, TA = -40 to +85C) Symbol Characteristics Min VIH VIL Input high voltage VPP Peak-to-peak Input voltage PCLK Common Mode Range PCLK Input low voltage VCMR1 VOH Output High Voltage VOL Output Low Voltage ZOUT IIN ICCQ 4 Typ 1.7 -0.3 Max Unit VCC + 0.3 0.7 V V mV LVPECL V LVPECL V IOH=-24 mA 2 0.6 V IOL= 15 mA 200 A mA 250 1.1 VCC-0.7 1.8 2 Output impedance 17 - 20 Input current3 Maximum Quiescent Supply Current Condition LVCMOS LVCMOS 2.0 VIN=GND or VIN=VCC All VCC Pins Note:1 VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR range and the input swing lies within the VPP (DC) specification. 2 The ASM2I99456 is capable of driving 50 transmission lines on the incident edge. Each output drives one 50 parallel terminated transmission line to a termination voltage of VTT. Alternatively, the device drives up to two 50 series terminated transmission lines. 3 Input pull-up / pull-down resistors influence input current. 4 ICCQ is the DC current consumption of the device with all outputs open and the input in its default state or open 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 5 of 14 ASM2I99456 June 2005 rev 0.2 Table 9. AC Characteristics (VCC = VCCA = VCCB = VCCC = 2.5V 5%, TA = -40 to +85C)1 Symbol fref fMAX Characteristics Input Frequency /1 output /2 output Maximum Output Frequency VPP Min 0 Typ 0 0 Max 2502 Unit MHz Condition 2502 125 MHz MHz FSELx=0 FSELx=1 Peak-to-peak input voltage PCLK 500 1000 mV LVPECL VCMR Common Mode Range PCLK 1.1 VCC-0.7 V LVPECL tP, REF Reference Input Pulse Width tr, tf tPLH tPHL tPLZ, HZ PCLK Input Rise/Fall Time 3 tPZL, LZ tsk(O) tsk(PP) tSK(P) 1.4 nS 1.04 nS 5.6 5.5 nS nS Output Disable Time 10 nS Output Enable Time Output-to-output Skew 10 nS 150 200 350 pS pS pS 3.0 nS 200 pS PCLK to any Q PCLK to any Q Propagation delay 2.6 2.6 Within one bank Any output bank, same output divider Any output, Any output divider Device-to-device Skew 5 Output pulse skew DCQ Output Duty Cycle tr, tf Output Rise/Fall Time /1 or /2 output 45 50 0.1 0.7 to 1.7V 55 % DCREF = 50% 1.0 nS 0.6 to 1.8V Note: 1 AC characteristics apply for parallel output termination of 50 to VTT. 2 The ASM2I99456 is functional up to an input and output clock frequency of 350MHz and is characterized up to 250 MHz. 3 VCMR (AC) is the crosspoint of the differential input signal. Normal AC operation is obtained when the crosspoint is within the VCMR range and the input swing lies within the VPP (AC) specification. 4 Violation of the 1.0nS maximum input rise and fall time limit will affect the device propagation delay, device-to-device skew, reference input pulse width, output duty cycle and maximum frequency specifications. 5 Output pulse skew is the absolute difference of the propagation delay times: | tPLH - tPHL |. Table 10. AC Characteristics (VCC = 3.3V 5%, VCCA = VCCB = VCCC = 2.5V 5% or 3.3V 5%,TA = -40 to +85C),1,2 Symbol Characteristics tsk(O) Min Typ Max Unit Output-to-output Skew Within one bank Any output bank, same output divider Any output, Any output divider 150 250 350 pS pS pS tsk(PP) Device-to-device Skew 2.5 nS tPLH,HL PCLK to any Q tSK(P) Propagation delay 3 Output pulse skew DCQ Output Duty Cycle /1 or /2 output Condition See 3.3V table 45 50 250 pS 55 % DCREF = 50% Note: 1 AC characteristics apply for parallel output termination of 50 to VTT. 2 For all other AC specifications, refer to 2.5V or 3.3V tables according to the supply voltage of the output bank. 3 Output pulse skew is the absolute difference of the propagation delay times: | tPLH - tPHL |. 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 6 of 14 ASM2I99456 June 2005 rev 0.2 Applications Information parallel combination of the 36 series resistor plus the output impedance does not match the parallel combination of the line impedances. The voltage wave launched down the two lines will equal: Driving Transmission Lines The ASM2I99456 clock driver was designed to drive high speed signals in a terminated transmission line environment. To provide the optimum flexibility to the user the output drivers were designed to exhibit the lowest impedance possible. With an output impedance of less than 20 the drivers can drive either parallel or series terminated transmission lines. In most high performance clock networks point-to-point distribution of signals is the method of choice. In a point-to-point scheme either series terminated or parallel terminated transmission lines can be used. The parallel technique terminates the signal at the end of the line with a 50 resistance to VCC/2. ASM2I99456 OUTPUT BUFFER 14 At the load end the voltage will double, due to the near unity reflection coefficient, to 2.5V. It will then increment towards the quiescent 3.0V in steps separated by one round trip delay (in this case 4.0nS). 3.0 2.5 VOLTAGE (V) This technique draws a fairly high level of DC current and thus only a single terminated line can be driven by each output of the ASM2I99456 clock driver. For the series terminated case however there is no DC current draw, thus the outputs can drive multiple series terminated lines. Figure 1. "Single versus Dual Transmission Lines" illustrates an output driving a single series terminated line versus two series terminated lines in parallel. When taken to its extreme the fanout of the ASM2I99456 clock driver is effectively doubled due to its capability to drive multiple lines. VL = VS ( Z0 / (RS+R0 +Z0)) Z0 = 50 || 50 RS = 36 || 36 R0 = 14 VL = 3.0 ( 25 / (18+14+25) = 1.31V OutA tD = 3.8956 OutB tD = 3.9386 2.0 In 1.5 1.0 0.5 Z0=50 RS=36 0 2 4 6 8 10 12 14 TIME (nS) ASM2I99456 OUTPUT BUFFER Z0=50 RS=36 14 RS=36 Z0=50 Figure 1. Single versus Dual Transmission Lines The waveform plots in Figure 2. "Single versus Dual Line Termination Waveforms" show the simulation results of an output driving a single line versus two lines. In both cases the drive capability of the ASM2I99456 output buffer is more than sufficient to drive 50 transmission lines on the incident edge. Note from the delay measurements in the simulations a delta of only 43pS exists between the two differently loaded outputs. This suggests that the dual line driving need not be used exclusively to maintain the tight output-to-output skew of the ASM2I99456. The output waveform in Figure 2. "Single versus Dual Line Termination Waveforms" shows a step in the waveform, this step is caused by the impedance mismatch seen looking into the driver. The Figure 2. Single versus Dual Waveforms Since this step is well above the threshold region it will not cause any false clock triggering, however designers may be uncomfortable with unwanted reflections on the line. To better match the impedances when driving multiple lines the situation in Figure 3. "Optimized Dual Line Termination" should be used. In this case the series terminating resistors are reduced such that when the parallel combination is added to the output buffer impedance the line impedance is perfectly matched. ASM2I99456 OUTPUT BUFFER RS=22 14 RS=22 Z0=50 Z0=50 14 + 22 || 22 = 50 || 50 25 = 25 Figure 3. Optimized Dual Line Termination 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 7 of 14 ASM2I99456 June 2005 rev 0.2 ASM2I99456 DUT Z0=50 Z0=50 Differential Pulse Generator Z=50 RT=50 RT=50 VTT VCC - 2V Figure 4. PCLK ASM2I99456 AC Test Reference for VCC = 3.3V and VCC = 2.5V PCLK VCC = 3.3V VCC = 2.5V 2.4 PCLK 1.8V 0.55 VCMR VPP 0.6V VCC tR tF VCC /2 QX Figure 5. Output Transition Time Test Reference tP(LH) GND tP(HL) Figure 6. Propagation Delay (tPD) Test Reference VCC VCC VCC /2 VCC /2 GND GND tP VOH VCC /2 T0 tSK(LH) DC (tP /T0 100%) tSK(HL) The pin-to-pin skew is defined as the worst case difference in propagation delay between any similar delay path within a single device The time from the output controlled edge to the non-controlled edge, divided by the time output controlled edge, expressed as a percentage. Figure 8. Output-to- Output Skew tSK(O) Figure 7. Output Duty Cycle (DC) VCC = 3.3V VCC = 2.5V tF GND 2.4 1.8V 0.55 0.6V tR Figure 9. Output Transition Time Test Reference 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 8 of 14 ASM2I99456 June 2005 rev 0.2 Power Consumption of the ASM2I99456 and Thermal Management The ASM2I99456 AC specification is guaranteed for the entire operating frequency range up to 250MHz. The ASM2I99456 power consumption and the associated long-term reliability may decrease the maximum frequency limit, depending on operating conditions such as clock frequency, supply voltage, output loading, ambient temperature, vertical convection and thermal conductivity of package and board. This section describes the impact of these parameters on the junction temperature and gives a guideline to estimate the ASM2I99456 die junction temperature and the associated device reliability. Table 11. Die junction temperature and MTBF Junction temperature (C) MTBF (Years) 100 20.4 110 9.1 120 4.2 130 2.0 Increased power consumption will increase the die junction temperature and impact the device reliability (MTBF). According to the system-defined tolerable MTBF, the die junction temperature of the ASM2I99456 needs to be controlled and the thermal impedance of the board/package should be optimized. The power dissipated in the ASM2I99456 is represented in equation 1. Where ICCQ is the static current consumption of the ASM2I99456, CPD is the power dissipation capacitance per output, ()CL represents the external capacitive output load, N is the number of active outputs (N is always 12 in case of the ASM2I99456). The ASM2I99456 supports driving transmission lines to maintain high signal integrity and tight timing parameters. Any transmission line will hide the lumped capacitive load at the end of the board trace, therefore, CL is zero for controlled transmission line systems and can be eliminated from equation 1. Using parallel termination output termination results in equation 2 for power dissipation. In equation 2, P stands for the number of outputs with a parallel or thevenin termination, VOL, IOL, VOH and IOH are a function of the output termination technique and DCQ is the clock signal duty cycle. If transmission lines are used CL is zero in equation 2 and can be eliminated. In general, the use of controlled transmission line techniques eliminates the impact of the lumped capacitive loads at the end lines and greatly reduces the power dissipation of the device. Equation 3 describes the die junction temperature TJ as a function of the power consumption. Where Rthja is the thermal impedance of the package (junction to ambient) and TA is the ambient temperature. According to Table 11, the junction temperature can be used to estimate the long-term device reliability. Further, combining equation 1 and equation 2 results in a maximum operating frequency for the ASM2I99456 in a series terminated transmission line system, equation 4. 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 9 of 14 ASM2I99456 June 2005 rev 0.2 TJ,MAX should be selected according to the MTBF system requirements and Table 11. Rthja can be derived from Table 12. The Rthja represent data based on 1S2P boards, using 2S2P boards will result in a lower thermal impedance than indicated below. Table 12. Thermal package impedance of the 32LQFP Convection, LFPM Still air 100 lfpm 200 lfpm 300 lfpm 400 lfpm 500 lfpm Rthja (1P2S board), C/W 86 76 71 68 66 60 Rthja (2P2S board), C/W 61 56 54 53 52 49 If the calculated maximum frequency is below 350 MHz, it becomes the upper clock speed limit for the given application conditions. The following eight derating charts describe the safe frequency operation range for the ASM2I99456. The charts were calculated for a maximum tolerable die junction temperature of 110C (120C), corresponding to an estimated MTBF of 9.1 years (4 years), a supply voltage of 3.3V and series terminated transmission line or capacitive loading. Depending on a given set of these operating conditions and the available device convection a decision on the maximum operating frequency can be made. 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 10 of 14 ASM2I99456 June 2005 rev 0.2 Package Information 32-lead LQFP Package SECTION A-A Dimensions Symbol Inches Min Max Millimeters Min Max A .... 0.0630 ... 1.6 A1 0.0020 0.0059 0.05 0.15 A2 0.0531 0.0571 1.35 1.45 D 0.3465 0.3622 8.8 9.2 D1 0.2717 0.2795 6.9 7.1 E 0.3465 0.3622 8.8 9.2 E1 0.2717 0.2795 6.9 7.1 L 0.0177 0.0295 0.45 0.75 L1 0.03937 REF 1.00 REF T 0.0035 0.0079 0.09 0.2 T1 0.0038 0.0062 0.097 0.157 b 0.0118 0.0177 0.30 0.45 b1 0.0118 0.0157 0.30 0.40 R0 0.0031 0.0079 0.08 0.20 e a 0.031 BASE 0 7 0.8 BASE 0 7 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 11 of 14 ASM2I99456 June 2005 rev 0.2 32-lead TQFP Package SECTION A-A Dimensions Symbol Inches Min Max Millimeters Min Max A .... 0.0472 ... 1.2 A1 0.0020 0.0059 0.05 0.15 A2 0.0374 0.0413 0.95 1.05 D 0.3465 0.3622 8.8 9.2 D1 0.2717 0.2795 6.9 7.1 E 0.3465 0.3622 8.8 9.2 E1 0.2717 0.2795 6.9 7.1 L 0.0177 0.0295 0.45 0.75 L1 0.03937 REF 1.00 REF T 0.0035 0.0079 0.09 0.2 T1 0.0038 0.0062 0.097 0.157 b 0.0118 0.0177 0.30 0.45 b1 0.0118 0.0157 0.30 0.40 R0 0.0031 0.0079 0.08 0.2 a 0 7 0 7 e 0.031 BASE 0.8 BASE 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 12 of 14 ASM2I99456 June 2005 rev 0.2 Ordering Information Part Number Marking Package Type Operating Range ASM2I99456-32-LT ASM2I99456L 32-pin LQFP, Tray Industrial ASM2I99456-32-LR ASM2I99456L 32-pin LQFP -Tape and Reel Industrial ASM2I99456G-32-LT ASM2I99456GL 32-pin LQFP, Tray, Green Industrial ASM2I99456G-32-LR ASM2I99456GL 32-pin LQFP -Tape and Reel, Green Industrial ASM2I99456-32-ET ASM2I99456E 32-pin TQFP, Tray Industrial ASM2I99456-32-ER ASM2I99456E 32-pin TQFP -Tape and Reel Industrial ASM2I99456G-32-ET ASM2I99456GE 32-pin TQFP, Tray, Green Industrial ASM2I99456G-32-ER ASM2I99456GE 32-pin TQFP -Tape and Reel, Green Industrial Device Ordering Information A S M 2 I 9 9 4 5 6 G - 3 2 - L R R = Tape & reel, T = Tube or Tray O = SOT S = SOIC T = TSSOP A = SSOP V = TVSOP B = BGA Q = QFN U = MSOP E = TQFP L = LQFP U = MSOP P = PDIP D = QSOP X = SC-70 DEVICE PIN COUNT F = LEAD FREE AND RoHS COMPLIANT PART G = GREEN PACKAGE PART NUMBER X= Automotive I= Industrial P or n/c = Commercial (-40C to +125C) (-40C to +85C) (0C to +70C) 1 = Reserved 2 = Non PLL based 3 = EMI Reduction 4 = DDR support products 5 = STD Zero Delay Buffer 6 = Power Management 7 = Power Management 8 = Power Management 9 = Hi Performance 0 = Reserved ALLIANCE SEMICONDUCTOR MIXED SIGNAL PRODUCT Licensed under US patent #5,488,627, #6,646,463 and #5,631,920. 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 13 of 14 ASM2I99456 June 2005 rev 0.2 Alliance Semiconductor Corporation 2575, Augustine Drive, Santa Clara, CA 95054 Tel# 408-855-4900 Fax: 408-855-4999 www.alsc.com Copyright (c) Alliance Semiconductor All Rights Reserved Part Number: ASM2I99456 Document Version: 0.2 Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to Alliance Semiconductor, dated 11-11-2003 (c) Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use. 3.3V/2.5V LVCMOS Clock Fanout Buffer Notice: The information in this document is subject to change without notice. 14 of 14