MELF MELF Resistors Resistors Welwyn Components WRM Series WRM Series High reliability s High reliability Predictable pulse handling capability pulse to handling s Predictable Tolerances down 0.1% capability down to 0.1% s Tolerances TCR down to 5 ppm/C * * * * s TCR down to 5 ppm/C Electrical Data WRM 0102 WRM 0204 WRM 0207 Power rating at 70C watts 0.125 0.25 0.4 Resistance range ohms 4R7 - 110K R22 - 5M1 R16 - 10 M Limiting element voltage TCR Resistance tolerance volts 150 200 250 ppm/C 50 5,10,15, 25, 50, 100 15, 25, 50, 100 % 1 0.1, 0.25, 0.5, 1.0, 2, 5 Standard values E24 & E96 Thermal impedance k/W Ambient temperature range 250 200 C Insulation resistance 140 -55 to +125 >1010 ohms Physical Data Dimensions (mm) and weight (g) Type L max D max D1 max WRM 0102 2.2 1.35 1.3 0.3 0.01 WRM 0204 3.7 1.55 1.55 0.5 0.02 WRM 0207 6.1 2.4 2.4 0.5 0.08 Construction A metal film is deposited onto a high dissipation ceramic former to which tin plated teminating caps are fitted. The resistor is adjusted to value by a helical cut in the film and the body is protected by a lacquer coating. Marking Resistance values are colour coded with four bands, three indicating value and one indicating the multiplier. (Note this describes standard marking, but certain values may still be supplied with the addition of a tolerance band following the multiplier.) K min Weight L D D1 L1 K Terminations Material Plated steel cap. Solderability The pure tin finish produces ageing free contacts on which low melting solders can be used. Dipped area shall be covered with a smooth and bright solder coating after 3 seconds immersion at 215C. Solvent Resistance The body protection and marking are resistant to all normal industrial cleaning solvents suitable for printed circuit boards. General General Note Note Welwyn Components reserves right to make in changes in specification product specification without TT electronics reserves the right the to make changes product without notice or notice liability.or liability. All information information isis subject subjectto toTT Welwyn's ownown datadata and and is considered accurate at time of going to print. All electronics' is considered accurate at time of going to print. A subsidiary of www.bitechnologies.com www.irctt.com www.welwyn-tt.com TT electronics plc (c) Welwyn Components Limited * Bedlington, Northumberland NE22 7AA, UK (c) TT electronics plc822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com Telephone: +44 (0) 1670 01. 11 11.12 MELF MELF Resistors Resistors Welwyn Components WRM Series Series WRM TCR and Tolerance Range Type TCR Tolerance Reference 5% 2% 1.0% 0.5% 0.25% 0.1% 50ppm - - 4R7 - 110K - - - 100ppm R22 - R91 - - - - - WRM0102 WRM0204 50ppm - - 1R - 5M1 10R - 1M6 22R - 332K 43R - 332K 25ppm - - 4R7 - 500K 10R - 500K 22R - 402K 43R - 332K 15ppm - - - 10R - 221K 22R - 221K 43R - 221K 10ppm - - - - 22R - 221K 43R - 221K 100R - 100K 100R - 100K 05ppm - - - - 100ppm R22 - R91 - - - - - 50ppm - - R16-10M 10R - 1M6 - - 25ppm - - 10R - 1M 10R - 500K 51R1 - 330K 100R - 100K 15ppm - - - 51R1 - 10K 51R1 - 10K 100R - 10K WRM0207 * TC 10ppm & 5ppm is specified over the temperature range -10C to +85C. Performance Data Test Results R/R 0204 & 0207: 75R - 100K 0.05% + 0.01 Short time overload* 0204 & 0207: 10R - <75R & >100K - 332K 0102: 4R7 - 110K, 0204 & 0207: R22 - <10R & >332K - 10M 0.1% + 0.01 0.25% + 0.05 Bending test* 0.05% + 0.01 0.1% + 0.01 0.25% + 0.05 Resistance to soldering heat 0.05% + 0.01 0.1% + 0.01 0.25% + 0.05 Temperature rapid change 0.05% + 0.01 0.1% + 0.01 0.25% + 0.05 0.25% + 0.05 0.25% + 0.05 0.5% + 0.05 Endurance* Load life 1000h 0.5% + 0.05 0.5% + 0.05 1.0% + 0.05 Climatic sequence* 0.25% + 0.05 0.5% + 0.05 1.0% + 0.05 Damp heat steady state* 0.25% + 0.05 0.5% + 0.05 1.0% + 0.05 < 0.25 V/V < 3 V/V 8000 h Current noise Solderability < 0.05 V/V Dipped area shall be covered with a smooth and bright solder coating of at least 96% Voltage coefficient Voltage proof < 0.5 . 106/V No flashover or breakdown * Resistors to be mounted on a PC-board according to IEC 115-1, clause 4.27.1 General Note TT electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT electronics' own data and is considered accurate at time of going to print. www.bitechnologies.com www.irctt.com www.welwyn-tt.com (c) Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK Telephone: +44 (0) 1670 (c) TT electronics plc822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com 01.11 11.12 MELF MELF Resistors MELF MELF Resistors MELF WRM Series Resistors Resistors WRM Series Resistors Welwyn Welwyn Welwyn Welwyn WRM Series Series WRM WRM Series Single Pulse Single Pulse Maximum Pulse Load Maximum Pulse Load Single Pulse Single Pulse Maximum Pulse Load WRM 0102 WRM 0204 0102 WRM 0207 WRM 0204 0102 WRM 0102 WRM 0207 0204 Pulse Pulse Load Pulse Load Pulse Load P max Load P maxP max P max 100 Maximum Pulse Load 100 W 100 W 100 10 W 10 W 0204 WRM 0207 WRM 0207 10 10 1 1 1 0,11 0,1 10 s 100 s 1 ms 10 ms 100 ms 1s 10 s 0,1 10 s 0,1 10 s 10 s 100 s 1 ms 10 ms 100 ms 1s 10 s 100 s 100 s 1 ms 1 ms 100 ms 100 ms 1s 1s 10 s 10 s Continuous Pulses Continuous Maximum PulsePulses Load Maximum PulsePulses Load Continuous Continuous Pulses Maximum Pulse Load Continuous Continuous Continuous Continuous Pulse Pulse Load Pulse Load Pulse Load PLoad P maxP max P max max Components Components Components Components Pulse Duration 10 ms Pulse Duration ti ti Pulse Duration Pulse Duration ti ti 10 ms WRM 0102 WRM 0204 0102 WRM 0207 WRM 0204 0102 WRM 0102 WRM 0207 0204 Maximum Pulse Load 100 100 W 100 W 100 10 W 10 W WRM 0204 0207 WRM 0207 10 10 1 1 1 0,11 0,1 10 s 100 s 1 ms 10 ms 100 ms 1s 10 s 0,1 10 s 0,1 10 s 10 s 100 s 1 ms 10 ms 100 ms 1s 10 s 100 s 100 s 1 ms 1 ms 100 ms 100 ms 1s 1s 10 s 10 s Pulse Duration 10 ms Pulse Duration 10 ms ti ti Packaging Pulse Duration ti Packaging Pulse Durationreeled ti The WRM 0102 and 0204 resistors are supplied on 8mm blister tape. The WRM and are 0204 resistors supplied reeled Packaging WRM 02070102 resistors supplied onare 12mm blister tape.on 8mm blister tape. Packaging WRM 02070102 resistors supplied onare 12mm blister tape.on 8mm blister tape. The WRM and are 0204 resistors supplied reeled Packaging complies the requirements ofblister IECreeled 286-3. The WRM andwith 0204 resistors supplied WRM 02070102 resistors are supplied onare 12mm tape.on 8mm blister tape. Packaging the requirements IEC 286-3. WRM 0207complies resistorswith are supplied on 12mmofblister tape. Packaging complies with the requirements of IEC 286-3. Packaging complies with the requirements of IEC 286-3. Ordering Procedure Ordering Procedure Example: WRM0204 at 1 kilohm, 1% tolerance and 50ppm/C TCR on a reel of 3000 pieces Ordering Procedure Example: WRM0204 at 1 kilohm, 1% tolerance and 50ppm/C TCR on a reel of 3000 pieces Ordering Procedure Type WRM 0204 C - and 1K050ppm/C F I on a reel of 3000 pieces Example: WRM0204 at 1 kilohm, 1% tolerance TCR Example: WRM0204 at 1 kilohm, 1% tolerance TCR Type WRM 0204 C - and 1K050ppm/C F I on a reel of 3000 pieces Size Type WRM 0204 C - 1K0 F I Size Type WRM 0204 C - 1K0 F I TCR Size TCR Size 0102 Z 100ppm/C Y 15ppm/C TCR 0102 Z 100ppm/C Y 15ppm/C I Tape 0204 TCR T 10ppm/C C 50ppm/C Z 100ppm/C Y T 15ppm/C 10ppm/C C 50ppm/C V 5ppm/C D 25ppm/C Z 100ppm/C Y 15ppm/C T 5ppm/C 10ppm/C C 25ppm/C 50ppm/C V D T 10ppm/C C 50ppm/C V 5ppm/C D 25ppm/C Value (use IEC62 code) 5ppm/C D 25ppm/C Value (use IEC62 Vcode) Tolerance IEC62 code) Value (use(use IEC62 code) Tolerance IEC62 code) Value (use(use IEC62 code) B 0.1% D 0.5% G 2% Tolerance (use IEC62 code) B 0.1% D IEC62 0.5% G 2% Tolerance C 0.25%(use F 1% code) J 5% Packing Packing Packing Standard Packing 3000 / reel (7") 3000 / reel (7") 3000 / reel (7")* 0102 3000 / reel (7")* (7") I Tape 0204 Standard 0207 0102 1500 3000 // reel reel (7") (7") I Tape 0204 3000 / reel (7")* Standard 0207 1500 (7") * High precision parts may be supplied on 1000 piece reels - please enquire I Tape 0204 3000 / reel (7")* Standard * High precision parts may be0207 supplied on 1000/piece 1500 reel reels (7")- please enquire 0207 1500 / reel (7") * High precision parts may be supplied on 1000 piece reels - please enquire * High precision parts may be supplied on 1000 piece reels - please enquire Note: F or zero-ohm versions order WRM0204C-R00FI or WRM0207C-R00FI B 0.1% 0.5% G 2% C 0.25% D F 1% J 5% Note: F or zero-ohm versions order WRM0204C-R00FI or WRM0207C-R00FI B 0.1% D 0.5% G 2% C 0.25% F 1% J 5% Note: F or zero-ohm versions order WRM0204C-R00FI or WRM0207C-R00FI 0.25% Components F 1% JLimited 5% Bedlington, Northumberland NE22 7AA, UK (c)CWelwyn Note: F or zero-ohm versions order WRM0204C-R00FI or WRM0207C-R00FI General Note 01.11 Telephone: +44Components (0) 1670 822181Limited * Facsimile:Bedlington, +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com (c) Welwyn Northumberland NE22 7AA, UK TT electronics reserves the 822181 right to *make changes product specification without notice or liability. 01.11 Telephone: +44 (0) 1670 Facsimile: +44in(0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com (c) Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK All information is subject to TT electronics' own data and is considered accurate at time of going to print. 01.11 Telephone: +44Components (0) 1670 822181Limited * Facsimile:Bedlington, +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com (c) Welwyn Northumberland NE22 7AA, UK www.bitechnologies.com www.irctt.com www.welwyn-tt.com 01.11 Telephone: +44 (0) 1670 822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com (c) TT electronics plc 11.12