ADMP404 Omnidirectional Microphone with Bottom Port and Analog Output APPLICATIONS GENERAL DESCRIPTION * The ADMP404 is a high-quality, high-performance, lowpower, analog-output bottom-ported omnidirectional MEMS microphone. The ADMP404 consists of a MEMS microphone element, an impedance converter, and an output amplifier. The ADMP404 sensitivity specification makes it an excellent choice for near-field applications. The ADMP404 has a wideband frequency response, resulting in natural sound with high intelligibility. Its low current consumption enables long battery life for portable applications. The ADMP404 complies with the TIA-920 Telecommunications Telephone Terminal Equipment Transmission Requirements for Wideband Digital Wireline Telephones standard. The ADMP404 is available in a miniature 3.35 x 2.50 x 0.88 mm surface-mount package. It is reflow solder compatible with no sensitivity degradation. The ADMP404 is halide free. * * * * * Mobile Devices Teleconferencing Systems Headsets Security Panels Intercom Devices FEATURES * * * * * * * * * 3.35 x 2.50 x 0.88 mm Surface-Mount Package SNR of 62 dBA Sensitivity of -38 dBV Flat Frequency Response from 100 Hz to 15 kHz Low Current Consumption: <250 A Single-Ended Analog Output High PSR of 70 dB Compatible with Sn/Pb and Pb-free Solder Processes RoHS/WEEE Compliant *Protected by U.S. Patents 7,449,356; 7,825,484; 7,885,423; and 7,961,897. Other patents are pending. ORDERING INFORMATION FUNCTIONAL BLOCK DIAGRAM OUTPUT AMPLIFIER OUTPUT PART TEMP RANGE PACKAGE ADMP404ACEZ-RL ADMP404ACEZ-RL7 EVAL-ADMP404Z-FLEX -40C to +85C* -40C to +85C -- CE-3-2 CE-3-2 -- * - 13" Tape and Reel ADMP404 - 7" Tape and Reel POWER VDD GND InvenSense reserves the right to change the detail specifications as may be required to permit improvements in the design of its products. InvenSense Inc. 1745 Technology Drive, San Jose, CA 95110 U.S.A +1(408) 988-7339 www.invensense.com Document Number: DS-ADMP404-00 Revision: 1.0. Release Date: Preliminary 11/20/2013 ADMP404 TABLE OF CONTENTS General Description ............................................................................................................................................. 1 Applications ......................................................................................................................................................... 1 Features ............................................................................................................................................................... 1 Functional Block Diagram .................................................................................................................................... 1 Ordering Information ........................................................................................................................................... 1 Table of Contents ............................................................................................................................................................ 2 Specifications .................................................................................................................................................................. 3 Table 1. Electrical Characteristics ........................................................................................................................ 3 Absolute Maximum Ratings ............................................................................................................................................ 4 Table 2. Absolute Maximum Ratings ................................................................................................................... 4 ESD Caution ......................................................................................................................................................... 4 Soldering Profile................................................................................................................................................... 5 Table 3. Recommended Soldering Profile............................................................................................................ 5 Pin Configurations And Function Descriptions ............................................................................................................... 6 Table 4. Pin Function Descriptions....................................................................................................................... 6 Typical Performance Characteristics............................................................................................................................... 7 APPLICATION INFORMATION .......................................................................................................................................... 8 CONNECTING TO AUDIO CODECS ........................................................................................................................ 8 Supporting Documents ................................................................................................................................................... 9 Evaluation Board User Guide ............................................................................................................................... 9 Circuit Note .......................................................................................................................................................... 9 Application Notes ................................................................................................................................................ 9 PCB Design And Land Pattern Layout ........................................................................................................................... 10 Handling Instructions .................................................................................................................................................... 11 Pick And Place Equipment ................................................................................................................................. 11 Reflow Solder ..................................................................................................................................................... 11 Board Wash........................................................................................................................................................ 11 Outline Dimensions ....................................................................................................................................................... 12 Ordering Guide .................................................................................................................................................. 12 Revision History ................................................................................................................................................. 12 Compliance Declaration Disclaimer: ..................................................................................................................... 13 Environmental Declaration Disclaimer: ................................................................................................................ 13 Document Number: DS-ADMP404-00 Revision: 1.0. Page 2 of 13 ADMP404 SPECIFICATIONS TABLE 1. ELECTRICAL CHARACTERISTICS (TA = -40 to 85C, VDD = 1.5 to 3.3 V, unless otherwise noted. All minimum and maximum specifications are guaranteed across temperature and voltage, and are specified in Table 1, unless otherwise noted. Typical specifications are not guaranteed.) PARAMETER PERFORMANCE Directionality Sensitivity CONDITIONS 1 kHz, 94 dB SPL MIN -41 Signal-to-Noise Ratio (SNR) Equivalent Input Noise (EIN) Dynamic Range Frequency Response Total Harmonic Distortion (THD) Power-Supply Rejection (PSR) Maximum Acoustic Input POWER SUPPLY Supply Voltage (VDD) Supply Current (IS) Derived from EIN and maximum acoustic input Low frequency -3 dB point High frequency -3 dB point 105 dB SPL 217 Hz, 100 mVp-p square wave superimposed on VDD = 1.8 V Peak TYP Omni -38 MAX -35 UNITS dBV 62 32 dBA dBA SPL 88 dB 100 15 Hz kHz % 3 70 dBFS 120 dB SPL 1.5 3.3 250 V A OUTPUT CHARACTERISTICS Output Impedance (ZOUT) 200 Output DC Offset 0.8 V 90 A Output Current Limit Note 1: See Figures 3 and 5. Document Number: DS-ADMP404-00 Revision: 1.0. Page 3 of 13 NOTES 1 ADMP404 ABSOLUTE MAXIMUM RATINGS Stress above those listed as Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to the absolute maximum ratings conditions for extended periods may affect device reliability. TABLE 2. ABSOLUTE MAXIMUM RATINGS PARAMETER Supply Voltage (VDD) Sound Pressure Level (SPL) Mechanical Shock Vibration Temperature Range RATING -0.3 V to +3.6 V 160 dB 10,000 g Per MIL-STD-883 Method 2007, Test Condition B -40C to +85C ESD CAUTION ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Document Number: DS-ADMP404-00 Revision: 1.0. Page 4 of 13 ADMP404 SOLDERING PROFILE CRITICAL ZONE TL TO TP tP TP TEMPERATURE RAMP-UP TL tL TSMAX TSMIN tS RAMP-DOWN PREHEAT t25C TO PEAK TIME Figure 1. Recommended Soldering Profile Limits TABLE 3. RECOMMENDED SOLDERING PROFILE PROFILE FEATURE Average Ramp Rate (TL to TP) Minimum Temperature (TSMIN) Minimum Temperature Preheat (TSMIN) Time (TSMIN to TSMAX), tS Ramp-Up Rate (TSMAX to TL) Time Maintained Above Liquidous (tL) Liquidous Temperature (TL) Peak Temperature (TP) Time Within +5C of Actual Peak Temperature (tP) Ramp-Down Rate Time +25C (t25C) to Peak Temperature Document Number: DS-ADMP404-00 Revision: 1.0. Sn63/Pb37 1.25C/sec max Pb-Free 1.25C/sec max 100C 100C 150C 200C 60 sec to 75 sec 1.25C/sec 45 sec to 75 sec 183C 60 sec to 75 sec 1.25C/sec ~50 sec 217C 215C +3C/-3C 245C +0C/-5C 20 sec to 30 sec 20 sec to 30 sec 3C/sec max 3C/sec max 5 min max 5 min max Page 5 of 13 ADMP404 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS GND 1 2 OUTPUT 3 ADMP404 VDD TOP VIEW (TERMINAL SIDE DOWN) Not to Scale Figure 2. Pin Configuration TABLE 4. PIN FUNCTION DESCRIPTIONS PIN NAME FUNCTION 1 OUTPUT 2 GND Analog Output Signal Ground 3 VDD Power Supply Document Number: DS-ADMP404-00 Revision: 1.0. Page 6 of 13 ADMP404 TYPICAL PERFORMANCE CHARACTERISTICS 10 10 8 4 0 2 (dB) SENSITIVITY (dB) 6 0 -2 -10 -4 -6 -8 -10 100 1k -20 100 10k Figure 3. Frequency Response Mask -10 -20 PSR (dB) -30 -40 -50 -60 -70 1k 10k FREQUENCY (Hz) Figure 5. Typical Power Supply Rejection Ratio vs. Frequency Document Number: DS-ADMP404-00 Revision: 1.0. 10k Figure 4. Typical Frequency Response (Measured) 0 -80 100 1k FREQUENCY (Hz) FREQUENCY (Hz) Page 7 of 13 ADMP404 APPLICATION INFORMATION CONNECTING TO AUDIO CODECS The ADMP404 output can be connected to a dedicated codec microphone input (see Figure 6) or to a high input impedance gain stage (see Figure 7.) A 0.1 F ceramic capacitor placed close to the ADMP404 supply pin is used for testing and is recommended to adequately decouple the microphone from noise on the power supply. A DC-blocking capacitor is required at the output of the microphone. This capacitor creates a high-pass filter with a corner frequency at fC = 1/(2 x C x R) where R is the input impedance of the codec. A minimum value of 2.2 F is recommended in Figure 6 because the input impedance of codecs can be as low as 2 k at its highest PGA gain setting, which results in a high-pass filter corner frequency at about 37 Hz. Figure 7 shows the ADMP404 connected to an op amp configured as a non-inverting preamplifier. MICBIAS 0.1F CODEC VDD 2.2F MINIMUM ADMP404 LINN OUTPUT LINP GND CM Figure 6. ADMP404 Connected to a Codec GAIN = (R1 + R2)/R1 0.1F R1 VREF R2 VDD ADMP404 1F MINIMUM VOUT OUTPUT GND 10k VREF Figure 7. ADMP404 Connected to an Op Amp Document Number: DS-ADMP404-00 Revision: 1.0. Page 8 of 13 ADMP404 SUPPORTING DOCUMENTS For additional information, see the following documents. EVALUATION BOARD USER GUIDE UG-325 Analog Output MEMS Microphone Flex Evaluation Board CIRCUIT NOTE CN-0207 High Performance Analog MEMS Microphone's Simple Interface to SigmaDSP Audio Codec CN-0262 Low Noise Analog MEMS Microphone and Preamp with Compression and Noise Gating APPLICATION NOTES AN-1003 Recommendations for Mounting and Connecting the Invensense Bottom-Ported MEMS Microphones AN-1068 Reflow Soldering of the MEMS Microphone AN-1112 Microphone Specifications Explained AN-1124 Recommendations for Sealing Invensense, Bottom-Port MEMS Microphones from Dust and Liquid Ingress AN-1140 Microphone Array Beamforming AN-1165 Op Amps for MEMS Microphone Preamp Circuits AN-1181 Using a MEMS Microphone in a 2-Wire Microphone Circuit Document Number: DS-ADMP404-00 Revision: 1.0. Page 9 of 13 ADMP404 PCB DESIGN AND LAND PATTERN LAYOUT The recommended PCB land pattern for the ADMP404 should be laid out to a 1:1 ratio to the solder pads on the microphone package, as shown in Figure 8. Take care to avoid applying solder paste to the sound hole in the PCB. A suggested solder paste stencil pattern layout is shown in Figure 9. The diameter of the sound hole in the PCB should be larger than the diameter of the sound port of the microphone. A minimum diameter of 0.5 mm is recommended. 1.52 0.68 1.22 0.61 O1.55 1.90 O0.95 0.61 0.90 Figure 8. PCB Land Pattern Layout Dimensions shown in millimeters 1.55/1.05 DIA. 0.225 CUT WIDTH (2x) 0.8 x 0.6 2x 1.22 0.2 x 45 TYP 1.52mm Figure 9. Suggested Solder Paste Stencil Pattern Layout Dimensions shown in millimeters Document Number: DS-ADMP404-00 Revision: 1.0. Page 10 of 13 ADMP404 HANDLING INSTRUCTIONS PICK AND PLACE EQUIPMENT The MEMS microphone can be handled using standard pick-and-place and chip shooting equipment. Take care to avoid damage to the MEMS microphone structure as follows: * Use a standard pickup tool to handle the microphone. Because the microphone hole is on the bottom of the package, the pickup tool can make contact with any part of the lid surface. * Do not pick up the microphone with a vacuum tool that makes contact with the bottom side of the microphone. Do not pull air out of or blow air into the microphone port. * Do not use excessive force to place the microphone on the PCB. REFLOW SOLDER For best results, the soldering profile must be in accordance with the recommendations of the manufacturer of the solder paste used to attach the MEMS microphone to the PCB. It is recommended that the solder reflow profile not exceed the limit conditions specified in Figure 1 and Table 3. BOARD WASH When washing the PCB, ensure that water does not make contact with the microphone port. Do not use blow-off procedures or ultrasonic cleaning. Document Number: DS-ADMP404-00 Revision: 1.0. Page 11 of 13 ADMP404 OUTLINE DIMENSIONS 3.425 3.350 3.275 0.75 REF REFERENCE CORNER 3.06 REF PIN 1 1.08 1.52 0.30 BSC 0.25 NOM DIA. 0.20 MIN THRU HOLE 0.90 x 0.68 (PINS 1, 3) 1.56 DIA. 1 2.575 2.500 2.425 2.21 REF 0.95 DIA. 0.54 REF 2 1.22 BSC 1.25 3 TOP VIEW 0.98 0.88 0.78 0.65 REF SIDE VIEW 0.64 REF 0.20 TYP x 45 BOTTOM VIEW 0.21 REF Figure 10. 3-Terminal Chip Array Small Outline No-Lead Cavity [LGA_CAV] 3.35 x 2.50 mm Body (CE-3-2) Dimensions shown in millimeters ORDERING GUIDE PART 1 ADMP404ACEZ-RL 1 ADMP404ACEZ-RL7 TEMP RANGE PACKAGE -40C to +85C 3-Terminal LGA_CAV* PACKAGE OPTION 2 CE-3-2 -40C to +85C 3-Terminal LGA_CAV CE-3-2 1,000 -- -- EVAL-ADMP404Z-FLEX -- Flex Evaluation Board * - 13" Tape and Reel - 7" Tape and Reel 1 2 Z = RoHS-Compliant Part This package option is halide free. REVISION HISTORY REVISION DATE REVISION DESCRIPTION 11/18/2013 1.0 Initial Release Document Number: DS-ADMP404-00 Revision: 1.0. Page 12 of 13 (SOUND PORT) 2 QUANTITY 10,000 ADMP404 Compliance Declaration Disclaimer: InvenSense believes this compliance information to be correct but cannot guarantee accuracy or completeness. Conformity documents for the above component constitutes are on file. InvenSense subcontracts manufacturing and the information contained herein is based on data received from vendors and suppliers, which has not been validated by InvenSense. Environmental Declaration Disclaimer: InvenSense believes this environmental information to be correct but cannot guarantee accuracy or completeness. Conformity documents for the above component constitutes are on file. InvenSense subcontracts manufacturing and the information contained herein is based on data received from vendors and suppliers, which has not been validated by InvenSense. This information furnished by InvenSense, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by InvenSense for its use, or for any infringements of patents or other rights of third parties that may result from its use. Specifications are subject to change without notice. InvenSense reserves the right to make changes to this product, including its circuits and software, in order to improve its design and/or performance, without prior notice. InvenSense makes no warranties, neither expressed nor implied, regarding the information and specifications contained in this document. InvenSense assumes no responsibility for any claims or damages arising from information contained in this document, or from the use of products and services detailed therein. This includes, but is not limited to, claims or damages based on the infringement of patents, copyrights, mask work and/or other intellectual property rights. Certain intellectual property owned by InvenSense and described in this document is patent protected. No license is granted by implication or otherwise under any patent or patent rights of InvenSense. This publication supersedes and replaces all information previously supplied. Trademarks that are registered trademarks are the property of their respective companies. InvenSense sensors should not be used or sold in the development, storage, production or utilization of any conventional or mass-destructive weapons or for any other weapons or life threatening applications, as well as in any other life critical applications such as medical equipment, transportation, aerospace and nuclear instruments, undersea equipment, power plant equipment, disaster prevention and crime prevention equipment. (c)2013 InvenSense, Inc. All rights reserved. InvenSense, MotionTracking, MotionProcessing, MotionProcessor, MotionFusion, MotionApps, DMP, and the InvenSense logo are trademarks of InvenSense, Inc. Other company and product names may be trademarks of the respective companies with which they are associated. (c)2013 InvenSense, Inc. All rights reserved. Document Number: DS-ADMP404-00 Revision: 1.0. Page 13 of 13