[TK631xxB/H/S]
AP-MS0037-E-00 - 1 - 2011/02
TK631xxH/S
1-
. DESCRIPTION
The TK631xxH/S is a CMOS LDO regulator. The
packages are the small and thin SON2017-6, and the
extremely versatile SOT23-5.
The IC is designed for portable applications with space
requirements, battery powered system and any electronic
equipment.
The IC does not require a noise-bypass capacitor.
The IC offers high accuracy (±1%) and low dropout
voltage.
The output voltage is internally fixed from 1.5V to 4.2V.
2-
. FEATURES
High accuracy (±1%)
Packages: SON2017-6 / SOT23-5
No noise bypass capacitor required
Low dropout voltage
Thermal and over current protection
High maximum load current
On/Off control
3-
. APPLICATIONS
Mobile Communication
Battery Powered System
Any Electronic Equipment
4-
. PIN CONFIGURATION
SON2017-6 (TK631xxH)
VOut
GND
VIn
(Top View)
VCont
NC
GND
6
5
4
1
2
3
SOT23-5 (TK631xxS)
VOut
1
2
3
5
4
GND
VIn
(Top View)
VCont NC
5-
. BLOCK DIAGRAM
VIn
GND
VCont
VOut
CIn COut
On/Off
Control
VRef
Thermal &
Over Current
Protection
CMOS LDO Regulator
[TK631xxB/H/S]
AP-MS0037-E-00 - 2 - 2011/02
6-
. ORDERING INFORMATION
T K 6 3 1
Voltage Code
(Refer to the following table)
Package Code
B : FC-4
H : SON2017-6 Package
S : SOT23-5 Package
Operating Temp. Range Code
C : C Rank(standard) only
Tape/Reel Code
B : Normal type for FC
L : Normal type for plastic packages
C
Solder Composion Code
- G : PB Free
- GH : PB Free & Halogen Free
brank : Lead Containing
Output Voltage
Voltage Code
Voltage Code
Output Voltage
Voltage Code
1.5V
15
28
3.3V
33
1.6V
16
01
3.5V
35
1.8V
18
29
2.5V
25
30
2.6V
26
31
2.7V
27
32
*If you need a voltage other than the value listed in the above table, please contact Asahi Kasei Microdevices.
7-
. ABSOLUTE MAXIMUM RATINGS
Ta=25C
Parameter
Symbol
Rating
Units
Conditions
Absolute Maximum Ratings
Input Voltage
VIn,MAX
-0.3 ~ 7.0
V
Output pin Voltage
VOut,MAX
-0.3 ~ VIn+0.3
V
Control pin Voltage
VCont,MAX
-0.3 ~ 7.0
V
Storage Temperature Range
Tstg
-55 ~ 150
C
Power Dissipation
PD
500
mW
Internal Limited Tj=150°C *,
When mounted on PCB
SON2017-6 , SOT23-5
Operating Condition
Operational Temperature Range
TOP
-40 ~ 85
C
Operational Voltage Range
VOP
2.0 ~ 6.0
V
* PD must be decreased at the rate of 2.9mW/C (FC-4) or 4mW/C (SON2017-6 , SOT23-5) for operation above 25C.
The maximum ratings are the absolute limitation values with the possibility of the IC breakage.
When the operation exceeds this standard quality can not be guaranteed.
[TK631xxB/H/S]
AP-MS0037-E-00 - 3 - 2011/02
8-
. ELECTRICAL CHARACTERISTICS
The parameters with min. or max. values will be guaranteed at Ta=Tj=25C with test when manufacturing or
SQC(Statistical Quality Control) methods. The operation between -40 ~ 85C is guaranteed when design.
VIn=VOut,TYP+1V, VCont=1.3V, Ta=Tj=25°C
Parameter
Symbol
Value
Units
Conditions
MIN
TYP
MAX
Output Voltage
VOut
Refer to TABLE 1
V
IOut=5mA
Line Regulation
LinReg
-
0.0
4.0
mV
VIn=1V
Load Regulation
LoaReg
Refer to TABLE 2
mV
Refer to TABLE 2
Dropout Voltage *1
VDrop
Refer to TABLE 2
mV
Refer to TABLE 2
Maximum Load Current *2
IOut,MAX
210
300
-
mA
VOut=VOut,TYP0.9
Quiescent Current
IQ
-
80
120
µA
IOut=0mA, VCont=VIn
Standby Current
IStandby
-
0.01
0.1
µA
VCont=0V
GND Pin Current
IGND
-
90
150
µA
IOut=50mA, VCont=VIn
Control Terminal
Control Current
ICont
-
2.0
4.0
µA
VCont=1.3V
Control Voltage
VCont
1.3
-
-
V
VOut On state
-
-
0.25
V
VOut Off state
Reference Value
Output Voltage / Temp.
VOut/Ta
-
100
-
ppm/°C
IOut=5mA
Output Noise Voltage
(TK63128)
VNoise
-
40
-
µVrms
COut=1.0µF , IOut=30mA ,
BPF=400Hz~80kHz
Ripple Rejection
(TK63128)
RR
-
70
-
dB
COut=1.0µF ,
IOut=10mA , f=1kHz
Rise Time
(TK63128)
tr
-
30
-
µs
COut=1.0µF ,
VCont : Pulse Wave (100Hz) ,
VCont On VOut95% point
*1: For VOut 2.0V , no regulations.
*2: The maximum output current is limited by power dissipation.
General Note
Parameters with only typical values are just reference. (Not guaranteed)
The noise level is dependent on the output voltage, the capacitance and capacitor characteristics.
[TK631xxB/H/S]
AP-MS0037-E-00 - 4 - 2011/02
TABLE 1. Preferred Product
Part Number
Output Voltage
MIN
TYP
MAX
V
V
V
TK63115H/S
1.485
1.500
1.515
TK63116H/S
1.584
1.600
1.616
TK63118H/S
1.782
1.800
1.818
TK63125H/S
2.475
2.500
2.525
TK63126H/S
2.574
2.600
2.626
TK63127H/S
2.673
2.700
2.727
TK63128H/S
2.772
2.800
2.828
TK63101H/S
2.821
2.850
2.879
TK63129H/S
2.871
2.900
2.929
TK63130H/S
2.970
3.000
3.030
TK63131H/S
3.069
3.100
3.131
TK63132H/S
3.168
3.200
3.232
TK63133H/S
3.267
3.300
3.333
TK63135H/S
3.465
3.500
3.535
Notice.
Please contact your authorized Asahi Kasei Microdevices representative for voltage availability.
[TK631xxB/H/S]
AP-MS0037-E-00 - 5 - 2011/02
TABLE 2. Preferred Product
Part Number
Load Regulation
Dropout Voltage
IOut=5 ~ 100mA
IOut=5 ~ 150mA
IOut=5 ~ 200mA
IOut=100mA
IOut=150mA
IOut=200mA
TYP
MAX
TYP
MAX
TYP
MAX
TYP
MAX
TYP
MAX
TYP
MAX
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
TK63115H/S
9
36
15
60
20
80
180
-
260
-
340
-
TK63116H/S
9
36
15
60
20
80
160
-
240
-
320
-
TK63118H/S
9
36
15
60
20
80
135
-
205
-
300
-
TK63125H/S
9
36
15
60
20
80
105
160
175
260
300
420
TK63126H/S
9
36
15
60
20
80
105
155
170
255
300
420
TK63127H/S
9
36
15
60
20
80
100
150
180
265
300
420
TK63128H/S
9
36
15
60
20
80
100
145
180
265
300
420
TK63101H/S
9
36
15
60
20
80
95
140
180
265
300
420
TK63129H/S
9
36
15
60
20
80
95
140
180
265
300
420
TK63130H/S
9
36
15
60
20
80
95
140
180
265
300
420
TK63131H/S
9
36
15
60
20
80
95
140
180
265
300
420
TK63132H/S
9
36
15
60
20
80
95
140
180
265
300
420
TK63133H/S
9
36
15
60
20
80
95
140
180
265
300
420
TK63135H/S
9
36
15
60
20
80
95
140
180
265
300
420
[TK631xxB/H/S]
AP-MS0037-E-00 - 6 - 2011/02
9-
. TEST CIRCUIT
IOut
=5mA
COut
=1.0uF
CIn
=1.0uF
VCont
V
_
A
_ICont VOut
VIn=
VOut,TYP+1.0V
A
_VIn VOut
VCont GND
IIn
Test circuit for electrical characteristic
Notice.
The limit value of electrical characteristics is applied when
CIn=1.0F(Ceramic), COut=1.0F(Ceramic).
But CIn, and COut can be used with both ceramic and
tantalum capacitors.
IOut
COut
=1.0uF
CIn
=1.0uF
VCont
V
_
A
_ICont VOut
VIn
VIn VOut
VCont GND
VOut vs VIn
VDrop vs IOut
VOut vs IOut
VOut vs IOut
VOut vs Ta
VDrop vs Ta
IOut,MAX vs Ta
ICont vs VCont , VOut vs VCont
ICont vs Ta
VCont vs Ta
VNoise vs VIn
VNoise vs IOut
VNoise vs VOut
VNoise vs Frequency
COut
=1.0uF
CIn
=1.0uF
VCont
A
_ICont
VIn=
VOut,TYP+1.0V
A
_VIn VOut
VCont GND
IIn
Open
IQ vs VIn
IStandby vs VIn
IQ vs Ta
IOut
COut
=1.0uF
CIn
=1.0uF
VCont
VIn=
VOut,TYP+1.0V
VIn VOut
VCont GND
A
_
IGND
A
_ICont
IGND vs IOut
IGND vs Ta
[TK631xxB/H/S]
AP-MS0037-E-00 - 7 - 2011/02
IOut
=10mA
COut
=1.0uF
VIn VOut
VCont GND
VIn=
VOut,TYP+1.5V
Vripple=
500mVP-P
VCont
=1.3V
RR vs VIn
RR vs Frequency
RR vs Frequency
COut
=1.0uF
V
_VOut
VIn VOut
VCont GND
VOut,TYP+1V
VOut,TYP+2V
VCont
=1.3V
IOut
=5mA
Line Transient
COut
=1.0uF
CIn
=1.0uF
V
_VOut
VIn=
VOut,TYP+1.0V
VIn VOut
VCont GND
IOut
VCont
=1.3V
Load Transient
IOut
=5mA
COut
=1.0uF
CIn
=1.0uF
V
_VOut
VIn=
VOut,TYP+1.0V
VIn VOut
VCont GND
VCont
=0V 1.3V
On/Off Transient
[TK631xxB/H/S]
AP-MS0037-E-00 - 8 - 2011/02
10-
. TYPICAL CHARACTERISTICS
10-1-
. DC CHARACTERISTICS
VOut vs VIn (TK63115H/S)
VIn [V]
0 1 2 3 4 5 6
VOut [mV]
-30
-25
-20
-15
-10
-5
0
5
10
IOut=5mA
VOut vs VIn (TK63128H/S)
VIn [V]
0 1 2 3 4 5 6
VOut [mV]
-30
-25
-20
-15
-10
-5
0
5
10
IOut=5mA
VOut vs VIn (TK63142H/S)
VIn [V]
0 1 2 3 4 5 6
VOut [mV]
-30
-25
-20
-15
-10
-5
0
5
10
IOut=5mA
VOut vs VIn (TK63115H/S)
VIn-VOut [mV]
-100 0 100 200 300
VOut [mV]
-100
-80
-60
-40
-20
0
20
40
IOut=0, 50, 100, 150mA
VOut vs VIn (TK63128H/S)
VIn-VOut [mV]
-100 0 100 200 300
VOut [mV]
-100
-80
-60
-40
-20
0
20
40
IOut=0, 50, 100, 150mA
VOut vs VIn (TK63142H/S)
VIn-VOut [mV]
-100 0 100 200 300
VOut [mV]
-100
-80
-60
-40
-20
0
20
40
IOut=0, 50, 100, 150mA
[TK631xxB/H/S]
AP-MS0037-E-00 - 9 - 2011/02
VDrop vs IOut (TK63115H/S)
IOut [mA]
050 100 150 200
VDrop [mV]
-400
-350
-300
-250
-200
-150
-100
-50
0
VDrop vs IOut (TK63128H/S)
IOut [mA]
050 100 150 200
VDrop [mV]
-400
-350
-300
-250
-200
-150
-100
-50
0
VDrop vs IOut (TK63142H/S)
IOut [mA]
050 100 150 200
VDrop [mV]
-400
-350
-300
-250
-200
-150
-100
-50
0
VOut vs IOut (TK63115H/S)
IOut [mA]
0 100 200 300 400 500
VOut [V]
0
0.5
1
1.5
2
VOut vs IOut (TK63128H/S)
IOut [mA]
0 100 200 300 400 500
VOut [V]
0
0.5
1
1.5
2
2.5
3
3.5
4
VOut vs IOut (TK63142H/S)
IOut [mA]
0 100 200 300 400 500
VOut [V]
0
1
2
3
4
5
6
[TK631xxB/H/S]
AP-MS0037-E-00 - 10 - 2011/02
VOut vs IOut (TK63115H/S)
IOut [mA]
050 100 150 200
VOut [mV]
-40
-35
-30
-25
-20
-15
-10
-5
0
5
10
VOut vs IOut (TK63128H/S)
IOut [mA]
050 100 150 200
VOut [mV]
-40
-35
-30
-25
-20
-15
-10
-5
0
5
10
VOut vs IOut (TK63142H/S)
IOut [mA]
050 100 150 200
VOut [mV]
-40
-35
-30
-25
-20
-15
-10
-5
0
5
10
VOut vs Ta (TK63115H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VOut [mV]
-100
-80
-60
-40
-20
0
20
40
60
80
100
VOut vs Ta (TK63128H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VOut [mV]
-100
-80
-60
-40
-20
0
20
40
60
80
100
VOut vs Ta (TK63142H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VOut [mV]
-100
-80
-60
-40
-20
0
20
40
60
80
100
[TK631xxB/H/S]
AP-MS0037-E-00 - 11 - 2011/02
VDrop vs Ta (TK63115H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VDrop [mV]
-400
-350
-300
-250
-200
-150
-100
-50
0
IOut=100mA
IOut=150mA
VDrop vs Ta (TK63128H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VDrop [mV]
-400
-350
-300
-250
-200
-150
-100
-50
0
IOut=100mA
IOut=150mA
VDrop vs Ta (TK63142H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VDrop [mV]
-400
-350
-300
-250
-200
-150
-100
-50
0
IOut=100mA
IOut=150mA
[TK631xxB/H/S]
AP-MS0037-E-00 - 12 - 2011/02
IOut,MAX vs Ta (TK63115H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IOut,MAX [mA]
200
300
400
IOut,MAX vs Ta (TK63128H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IOut,MAX [mA]
200
300
400
IOut,MAX vs Ta (TK63142H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IOut,MAX [mA]
200
300
400
IQ vs VIn (TK63115H/S)
VIn [V]
0 1 2 3 4 5 6
IQ [µA]
0
20
40
60
80
100
120
140
VCont=VIn
IQ vs VIn (TK63128H/S)
VIn [V]
0 1 2 3 4 5 6
IQ [µA]
0
20
40
60
80
100
120
140
VCont=VIn
IQ vs VIn (TK63142H/S)
VIn [V]
0 1 2 3 4 5 6
IQ [µA]
0
20
40
60
80
100
120
140
VCont=VIn
[TK631xxB/H/S]
AP-MS0037-E-00 - 13 - 2011/02
IStandby vs VIn (TK63115H/S)
VIn [V]
0 1 2 3 4 5 6
IStandby [nA]
0
1
2
3
4
5
6
7
8
9
10
VCont=0V
IStandby vs VIn (TK63128H/S)
VIn [V]
0 1 2 3 4 5 6
IStandby [nA]
0
1
2
3
4
5
6
7
8
9
10
VCont=0V
IStandby vs VIn (TK63142H/S)
VIn [V]
0 1 2 3 4 5 6
IStandby [nA]
0
1
2
3
4
5
6
7
8
9
10
VCont=0V
IGND vs IOut (TK63115H/S)
IOut [mA]
050 100 150 200
IGND [µA]
0
20
40
60
80
100
120
140
160
180
200
VCont=VIn
IGND vs IOut (TK63128H/S)
IOut [mA]
050 100 150 200
IGND [µA]
0
20
40
60
80
100
120
140
160
180
200
VCont=VIn
IGND vs IOut (TK63142H/S)
IOut [mA]
050 100 150 200
IGND [µA]
0
20
40
60
80
100
120
140
160
180
200
VCont=VIn
[TK631xxB/H/S]
AP-MS0037-E-00 - 14 - 2011/02
IQ vs Ta (TK63115H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IQ [µA]
0
20
40
60
80
100
120
140
VCont=VIn
IQ vs Ta (TK63128H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IQ [µA]
0
20
40
60
80
100
120
140
VCont=VIn
IQ vs Ta (TK63142H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IQ [µA]
0
20
40
60
80
100
120
140
VCont=VIn
IGND vs Ta (TK63115H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IGND [µA]
0
20
40
60
80
100
120
140
VCont=VIn, IOut=50mA
IGND vs Ta (TK63128H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IGND [µA]
0
20
40
60
80
100
120
140
VCont=VIn, IOut=50mA
IGND vs Ta (TK63142H/S)
Ta [°C]
-50 -25 0 25 50 75 100
IGND [µA]
0
20
40
60
80
100
120
140
VCont=VIn, IOut=50mA
[TK631xxB/H/S]
AP-MS0037-E-00 - 15 - 2011/02
ICont vs VCont, VOut vs VCont (TK63115H/S)
VCont [V]
0 0.5 1 1.5 2
VOut [V]
0
0.5
1
1.5
2
ICont [µA]
0
2
4
6
8
VOut
ICont
ICont vs VCont, VOut vs VCont (TK63128H/S)
VCont [V]
0 0.5 1 1.5 2
VOut [V]
0
1
2
3
4
ICont [µA]
0
2
4
6
8
VOut
ICont
ICont vs VCont, VOut vs VCont (TK63142H/S)
VCont [V]
0 0.5 1 1.5 2
VOut [V]
0
1
2
3
4
5
6
ICont [µA]
0
1
2
3
4
5
6
VOut
ICont
VCont vs Ta (TK63115H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VCont [V]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
VCont vs Ta (TK63128H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VCont [V]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
VCont vs Ta (TK63142H/S)
Ta [°C]
-50 -25 0 25 50 75 100
VCont [V]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
[TK631xxB/H/S]
AP-MS0037-E-00 - 16 - 2011/02
ICont vs Ta (TK631xxH/S)
Ta [°C]
-50 -25 0 25 50 75 100
ICont [µA]
0
0.5
1
1.5
2
2.5
VCont=1.3V
[TK631xxB/H/S]
AP-MS0037-E-00 - 17 - 2011/02
10-2-
. AC CHARACTERISTICS
RR vs VIn (TK63115H/S)
VIn-VOut [V]
0 0.5 1 1.5 2 2.5 3 3.5
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=200mA
150mA
100mA
50mA
10mA
CIn=1.0µF, Vripple=0.1Vp-p, f=1kHz
RR vs VIn (TK63128H/S)
VIn-VOut [V]
0 0.5 1 1.5 2 2.5 3 3.5
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=200mA
150mA
100mA
50mA
10mA
CIn=1.0µF, Vripple=0.1Vp-p, f=1kHz
RR vs VIn (TK63142H/S)
VIn-VOut [V]
0 0.5 1 1.5 2 2.5
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=200mA
150mA
100mA
50mA
10mA
CIn=1.0µF, Vripple=0.1Vp-p, f=1kHz
RR vs Frequency (TK63115H/S)
Frequency [Hz]
100 1k 10k 100k
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1M
IOut=10mA
COut=1.0µF(cer.)
COut=1.0µF(tant.)
RR vs Frequency (TK63128H/S)
Frequency [Hz]
100 1k 10k 100k 1M
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=10mA
COut=1.0µF(cer.)
COut=1.0µF(tant.)
RR vs Frequency (TK63142H/S)
Frequency [Hz]
100 1k 10k 100k 1M
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=10mA
COut=1.0µF(cer.)
COut=1.0µF(tant.)
[TK631xxB/H/S]
AP-MS0037-E-00 - 18 - 2011/02
RR vs Frequency (TK63115H/S)
Frequency [Hz]
100 1k 10k 100k 1M
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=10mA
COut=0.68µ, 1.0µ, 2.2µ, 4.7µF(cer.)
RR vs Frequency (TK63128H/S)
Frequency [Hz]
100 1k 10k 100k 1M
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=10mA
COut=0.68µ, 1.0µ, 2.2µ, 4.7µF(cer.)
RR vs Frequency (TK63142H/S)
Frequency [Hz]
100 1k 10k 100k 1M
RR [dB]
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
IOut=10mA
COut=0.68µ, 1.0µ, 2.2µ, 4.7µF(cer.)
The ripple rejection (RR) characteristic depends on the
characteristic and the capacitance value of the capacitor
connected to the output side. The RR characteristic of
50kHz or more varies greatly with the capacitor on the
output side and PCB pattern. If necessary, please confirm
stability of your design.
[TK631xxB/H/S]
AP-MS0037-E-00 - 19 - 2011/02
VNoise vs VIn (TK63115H/S)
VIn [V]
1 2 3 4 5 6
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
IOut=30mA
VNoise vs VIn (TK63128H/S)
VIn [V]
2.5 3 3.5 4 4.5 5 5.5 6
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
IOut=30mA
VNoise vs VIn (TK63142H/S)
VIn [V]
4 4.5 5 5.5 6
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
IOut=30mA
VNoise vs IOut (TK63115H/S)
IOut [mA]
050 100 150 200
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
VNoise vs IOut (TK63128H/S)
IOut [mA]
050 100 150 200
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
VNoise vs IOut (TK63142H/S)
IOut [mA]
050 100 150 200
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
[TK631xxB/H/S]
AP-MS0037-E-00 - 20 - 2011/02
VNoise vs VOut (TK631xxH/S)
VOut [V]
1.5 2 2.5 3 3.5 4 4.5
VNoise [µVrms]
0
10
20
30
40
50
60
70
80
90
100
IOut=30mA
VNoise vs Frequency (TK63115H/S)
Frequency [Hz]
10 100 1k 10k
VNoise [µV/√Hz]
0.01
0.1
1
100k
IOut=10mA
10
VNoise vs Frequency (TK63128H/S)
Frequency [Hz]
10 100 1k 10k
VNoise [µV/√Hz]
0.01
0.1
1
100k
IOut=10mA
10
VNoise vs Frequency (TK63142H/S)
Frequency [Hz]
10 100 1k 10k
VNoise [µV/√Hz]
0.01
0.1
1
100k
IOut=10mA
10
[TK631xxB/H/S]
AP-MS0037-E-00 - 21 - 2011/02
10-3-
. TRANSIENT CHARACTERISTICS
Line Transient (TK63115H/S)
Time
20µsec/div
10mV/div
VIn
VOut
3.5V
2.5V
IOut=30, 100, 150mA
Line Transient (TK63128H/S)
Time
20µsec/div
10mV/div
VIn
VOut
4.8V
3.8V
IOut=30, 100, 150mA
Line Transient (TK63142H/S)
Time
20µsec/div
10mV/div
VIn
VOut
6.2V
5.2V
IOut=30, 100, 150mA
Load Transient (IOut=5100mA) (TK63115H/S)
Time
10µsec/div
50mV/div
100mA/div
IOut
VOut
COut=2.2µF
5mA 100mA
COut=0.68µF
COut=1.0µF
Load Transient (IOut=5100mA) (TK63128H/S)
Time
10µsec/div
50mV/div
100mA/div
IOut
VOut
COut=1.0µF
COut=0.68µF
COut=2.2µF
5mA 100mA
Load Transient (IOut=5100mA) (TK63142H/S)
Time
10µsec/div
50mV/div
100mA/div
IOut
VOut
COut=1.0µF
COut=0.68µF
COut=2.2µF
5mA 100mA
[TK631xxB/H/S]
AP-MS0037-E-00 - 22 - 2011/02
Load Transient (IOut=0100mA) (TK63115H/S)
Time
5msec/div
100mA/div
IOut
VOut 100mV/div
100mA
0 or 5mA
0 100mA
5 100mA
Load Transient (IOut=0100mA) (TK63128H/S)
Time
2msec/div
100mA/div
IOut
VOut 100mV/div
100mA
0 or 5mA
0 100mA
5 100mA
Load Transient (IOut=0100mA) (TK63142H/S)
Time
1msec/div
100mA/div
IOut
VOut 100mV/div
100mA
0 or 5mA
0 100mA
5 100mA
Time
10µsec/div
100mA/div
IOut
VOut 100mV/div
100mA
0 or 5mA
0 100mA
5 100mA
Time
10µsec/div
100mA/div
IOut
VOut 100mV/div
100mA
0 or 5mA
0 100mA
5 100mA
Time
10µsec/div
100mA/div
IOut
VOut 100mV/div
100mA
0 or 5mA
0 100mA
5 100mA
[TK631xxB/H/S]
AP-MS0037-E-00 - 23 - 2011/02
On/Off Transient (VCont=01.3V) (TK63115H/S)
Time
10µsec/div
0.5V/div
200mA/div
VCont
IIn
VOut
1V/div
IOut=30mA
COut=0.68, 1.0, 2.2, 4.7µF
On/Off Transient (VCont=01.3V) (TK63128H/S)
Time
10µsec/div
1V/div
200mA/div
VCont
IIn
VOut
1V/div
IOut=30mA
COut=0.68, 1.0, 2.2, 4.7µF
On/Off Transient (VCont=01.3V) (TK63142H/S)
Time
10µsec/div
2V/div
200mA/div
VCont
IIn
VOut
1V/div
IOut=30mA
COut=0.68, 1.0, 2.2, 4.7µF
On/Off Transient (VCont=1.30V) (TK63115H/S)
Time
200µsec/div
0.5V/div
200mA/div
VCont
IIn
VOut
1V/div
IOut=30mA
COut=0.68, 1.0, 2.2, 4.7µF
On/Off Transient (VCont=1.30V) (TK63128H/S)
Time
200µsec/div
1V/div
200mA/div
VCont
IIn
VOut
1V/div
IOut=30mA
COut=0.68, 1.0, 2.2, 4.7µF
On/Off Transient (VCont=1.30V) (TK63142H/S)
Time
200µsec/div
2V/div
200mA/div
VCont
IIn
VOut
1V/div
IOut=30mA
COut=0.68, 1.0, 2.2, 4.7µF
[TK631xxB/H/S]
AP-MS0037-E-00 - 24 - 2011/02
11-
. PIN DESCRIPTION
Pin No.
Pin
Description
Internal Equivalent Circuit
Description
TK631xxH
TK631xxS
2, 5
2
GND
GND Terminal
6
3
VCont
VCont
675k
ESD
protection
Control Terminal
VCont > 1.3V : On
VCont < 0.25V : Off
The pull-down resistor (about
675k) is built-in.
3
5
VOut
VOut
VIn
ESD
protection
Output Terminal
1
1
VIn
Input Terminal
4
4
NC
No Connected
[TK631xxB/H/S]
AP-MS0037-E-00 - 25 - 2011/02
12-
. APPLICATIONS INFORMATION
12-1-
. Stability
Linear regulators require input and output capacitors in
order to maintain the regulator's loop stability. If a 1.0µF
capacitor is connected to the output side, the IC provides
stable operation. However, it is recommended to use as
large a value capacitor as is practical. The output noise
and the ripple noise decrease as the value of the capacitor
increases.
A recommended value of the application is as follows.
CIn=1.0µF, COut=1.0µF
It is not possible to determine this indiscriminately.
Please confirm the stability in your design.
Fig12-1: Capacitor in the application
TK631xx VOut
VCont
VIn
COut
1.0µFCIn
1.0µF
Fig12-2: Output Current vs Stable Operation Area
(TK631xxH/S)
TK63115H/S
0.01
0.1
1
10
100
050 100 150 200
IOut (mA)
ESR ()
Unstable Area
Stable Area
COut=0.68uF
TK63128H/S
0.01
0.1
1
10
100
050 100 150 200
IOut (mA)
ESR ()
Unstable Area
Stable Area
COut=0.68uF
TK63142H/S
0.01
0.1
1
10
100
050 100 150 200
IOut (mA)
ESR ()
Unstable Area
Stable Area
COut=0.68uF
[TK631xxB/H/S]
AP-MS0037-E-00 - 26 - 2011/02
Fig.Error! Reference source not found. and Fig.12-2
show the stable operation area of output current and the
equivalent series resistance (ESR) with a ceramic
capacitor of 0.68µF. ESR of the output capacitor must be
in the stable operation area. Please select the best output
capacitor according to the voltage and current used. The
stability of the regulator improves as the value of the
output side capacitor increases (the stable operation area
extends.) Please use as large a value capacitor as is
practical.
For evaluation
Kyocera : CM05B104K10AB , CM05B224K10AB ,
CM105B104K16A , CM105B224K16A ,
CM21B225K10A
Murata : GRM36B104K10 , GRM42B104K10 ,
GRM39B104K25 , GRM39B224K10 ,
GRM39B105K6.3
Fig12-3: ex. Ceramic Capacitance vs Voltage,
Temperature
CAP(%)
12
50
Bias Voltage(V)
CAP(%)
100
Ta(°C)
Capacitance vs Voltage
Capacitance vs Temperature
B Curve
F Curve
1086420
60
70
80
90
100
B Curve
F Curve
7550250-25-50
50
60
70
80
90
100
Generally, a ceramic capacitor has both a temperature
characteristic and a voltage characteristic. Please consider
both characteristics when selecting the part. The B curves
are the recommended characteristics.
[TK631xxB/H/S]
AP-MS0037-E-00 - 27 - 2011/02
12-2-
. Layout
Fig12-4: Layout example (TK631xxH)
VCont
VIn VOut
GND
(Top View)
NCGND
PCB Material : Glass epoxy
Size : 10mm7mm×0.8mm
Fig12-5: Layout example (TK631xxS)
VCont
VIn
VOut
GND
(Top View)
NCGND
PCB Material : Glass epoxy
Size : 12mm7mm×0.8mm
Please do derating with with 4mW/C at
Pd=500mW(SON2017-6/SOT23-5), and 25C or more.
Thermal resistance (ja) is=250C/W.
Fig12-6: Derating Curve (TK631xxH/S)
25 50 100 150°C
Pd(mW)
500
(85°C)
-4mW/°C
The package loss is limited at the temperature that the
internal temperature sensor works (about 150C).
Therefore, the package loss is assumed to be an internal
limitation. There is no heat radiation characteristic of the
package unit assumed because of its small size. Heat is
carried away from the device by being mounted on the
PCB. This value is directly effected by the material and
the copper pattern etc. of the PCB. The losses are
approximately 500mW(SON2017-6/SOT23-5). Enduring
these losses becomes possible in a lot of applications
operating at 25C.
The overheating protection circuit operates when the
junction temperature reaches 150C (this happens when
the regulator is dissipating excessive power, outside
temperature is high, or heat radiation is bad). The output
current and the output voltage will drop when the
protection circuit operates. However, operation begins
again as soon as the output voltage drops and the
temperature of the chip decreases.
How to determine the thermal resistance when
mounted on PCB
The thermal resistance when mounted is expressed as
follows:
Tj=jaPd+Ta
Tj of IC is set around 150C. Pd is the value when the
thermal sensor is activated.
If the ambient temperature is 25C, then:
150=jaPd+25
ja=125/Pd (C /mW)
[TK631xxB/H/S]
AP-MS0037-E-00 - 28 - 2011/02
Pd is easily calculated.
A simple way to determine Pd is to calculate VInIIn
when the output side is shorted. Input current gradually
falls as output voltage rises after working thermal
shutdown. You should use the value when thermal
equilibrium is reached.
Fig12-7: How to determine DPd
25 50 100 150
Pd (mW)
Pd
Ta (°C)
75 125
DPd
2
3
4
5
Procedure (When mounted on PCB.)
1. Find Pd (VInIIn when the output side is short-
circuited).
2. Plot Pd against 25C.
3. Connect Pd to the point corresponding to the 150C
with a straight line.
4. In design, take a vertical line from the maximum
operating temperature (e.g., 75C) to the derating
curve.
5. Read off the value of Pd against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation DPd.
6. DPd (VIn,MAXVOut)=IOut (at 75C)
The maximum output current at the highest operating
temperature will be IOut DPd (VIn,MAXVOut).
Please use the device at low temperature with better
radiation. The lower temperature provides better quality.
12-3-
. On/Off Control
It is recommended to turn the regulator Off when the
circuit following the regulator is not operating. A design
with little electric power loss can be implemented. We
recommend the use of the On/Off control of the regulator
without using a high side switch to provide an output
from the regulator. A highly accurate output voltage with
low voltage drop is obtained.
Because the control current is small, it is possible to
control it directly by CMOS logic.
Fig12-8: The use of On/Off control
REG
Vsat
On/Off Cont.
Control Terminal Voltage ((VCont)
On/Off State
VCont > 1.3V
On
VCont < 0.25V
Off
Parallel Connected On/Off Control
Fig12-9: The example of parallel connected IC
TK63142
TK63133
TK63115
4.2V
3.3V
1.5V
On/Off
Cont.
VIn VOut
The above figure is multiple regulators being controlled
by a single On/Off control signal. There is concern of
overheating, because the power loss of the low voltage
side IC (TK63115H/S) is large. The series resistor (R) is
put in the input line of the low output voltage regulator in
order to prevent over-dissipation. The voltage dropped
across the resistor reduces the large input-to-output
voltage across the regulator, reducing the power
dissipation in the device. When the thermal sensor works,
a decrease of the output voltage, oscillation, etc. may be
observed.
[TK631xxB/H/S]
AP-MS0037-E-00 - 29 - 2011/02
12-4-
. Definition of term
Characteristics
Output Voltage (VOut)
The output voltage is specified with VIn=(VOutTYP+1V)
and IOut=5mA.
Maximum Output Current (IOut, MAX)
The rated output current is specified under the condition
where the output voltage drops to 90% of the value
specified with IOut=5mA. The input voltage is set to
VOutTYP+1V and the current is pulsed to minimize
temperature effect.
Dropout Voltage (VDrop)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the
regulator starts to fall out of regulation. Below this value,
the output voltage will fall as the input voltage is reduced.
It is dependent upon the output voltage, the load current,
and the junction temperature.
Line Regulation (LinReg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
from VIn=VOut,TYP+1V to VIn=6V. It is a pulse
measurement to minimize temperature effect.
Load Regulation (LoaReg)
Load regulation is the ability of the regulator to maintain
a constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects
with the input voltage set to VIn=VOut,TYP+1V. The load
regulation is specified under an output current step
condition of 5mA to 100mA.
Ripple Rejection (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 500mVP-P, 1kHz super-imposed on the
input voltage, where VIn=VOut,TYP+1.5V. Ripple rejection
is the ratio of the ripple content of the output vs. input and
is expressed in dB.
Standby Current (IStandby)
Standby current is the current which flows into the
regulator when the output is turned off by the control
function (VCont=0V).
Protections
Over Current Sensor
The over current sensor protects the device when there is
excessive output current. It also protects the device if the
output is accidentally connected to ground.
Thermal Sensor
The thermal sensor protects the device in case the
junction temperature exceeds the safe value (Tj=150C).
This temperature rise can be caused by external heat,
excessive power dissipation caused by large input to
output voltage drops, or excessive output current. The
regulator will shut off when the temperature exceeds the
safe value. As the junction temperatures decrease, the
regulator will begin to operate again. Under sustained
fault conditions, the regulator output will oscillate as the
device turns off then resets. Damage may occur to the
device under extreme fault.
Please prevent the loss of the regulator when this
protection operates, by reducing the input voltage or
providing better heat efficiency.
ESD
MM : 200pF 0 150V or more
HBM : 100pF 1.5k 2000V or more
[TK631xxB/H/S]
AP-MS0037-E-00 - 30 - 2011/02
13-
. PACKAGE OUTLINE
6-Lead-Small Outline Non-Leaded Package : SON2017-6
1.7
0.20+0.10
0.05
0.65 M
0.10
+0.2
0.1
2.0 +0.2
0.1
1
4
3
6
(0.1)
0.75
(0.2)
0.10
0.125+0.10
0.05
2.1 0.2
(0.2)
1
4
3
6
Reference Mount Pad
1.8
0.6
0.3
0.65
Mark
1 Pin Mark Lot No.
Lead Free Mark
Unit : mm
Package Structure and Others
Package Material
:
Epoxy Resin
Mark Method
:
Laser
Terminal Material
:
Copper Alloy
County of Origin
:
Japan
Terminal Finish
:
Lead Free Solder Plating(5~15µm)
Mass
:
0.0066g
Solder Composition
:
Sn-2.5Ag
Marking
Part Number
Marking Code
Part Number
Marking Code
Part Number
Marking Code
TK63115H
C15
TK63128H
C28
TK63133H
C33
TK63116H
C16
TK63101H
C01
TK63135H
C35
TK63118H
C18
TK63129H
C29
TK63125H
C25
TK63130H
C30
TK63126H
C26
TK63131H
C31
TK63127H
C27
TK63132H
C32
[TK631xxB/H/S]
AP-MS0037-E-00 - 31 - 2011/02
5-Lead-Surface Mount Discrete Package: SOT23-5
2.9
1.6
1.1
0.15
0.4
2.8
Reference Mount Pad
(0.3)
0 ~0.1 0.1
1.3max
0.1
0.2
Mark
0.2
0.2
54
13
+0.10
0.05
+0.10
0.05
0.4 0.2
0.95 0.95
Lead Free Mark
+
M
0.1
+
+
+
+
2.4
1.0
0.7
0.95 0.95
Unit : mm
Package Structure and Others
Package Material
:
Epoxy Resin
Mark Method
:
Laser
Terminal Material
:
Copper Alloy
Country of Origin
:
Japan
Terminal Finish
:
Lead Free Solder Plating(5~15m)
Mass
:
0.016g
Solder Composition
:
Sn-2.5Ag
Marking
Part Number
Marking Code
Part Number
Marking Code
Part Number
Marking Code
TK63115S
15J
TK63128S
28J
TK63133S
33J
TK63116S
16J
TK63101S
01J
TK63135S
35J
TK63118S
18J
TK63129S
29J
TK63125S
25J
TK63130S
30J
TK63126S
26J
TK63131S
31J
TK63127S
27J
TK63132S
32J
[TK631xxB/H/S]
AP-MS0037-E-00 - 32 - 2011/02
IMPORTANT NOTICE
These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of
Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the
products.
Descriptions of external circuits, application circuits, software and other related information contained
in this document are provided only to illustrate the operation and application examples of the
semiconductor products. You are fully responsible for the incorporation of these external circuits,
application circuits, software and other related information in the design of your equipments. AKM
assumes no responsibility for any losses incurred by you or third parties arising from the use of these
information herein. AKM assumes no liability for infringement of any patent, intellectual property, or
other rights in the application or use of such information contained herein.
Any export of these products, or devices or systems containing them, may require an export license or
other official approval under the law and regulations of the country of export pertaining to customs
and tariffs, currency exchange, or strategic materials.
AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety,
life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for
such use, except for the use approved with the express written consent by Representative Director of
AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system
containing it, and which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of
safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to
function or perform may reasonably be expected to result in loss of life or in significant injury or damage to
person or property.
It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or
otherwise places the product with a third party, to notify such third party in advance of the above
content and conditions, and the buyer or distributor agrees to assume any and all responsibility and
liability for and hold AKM harmless from any and all claims arising from the use of said product in
the absence of such notification.