HLMP-Pxxx Series, HLMP-Qxxx Series
HLMP-6xxx Series, HLMP-70xx Series
Features
Subminiature flat top package
ideal for backlighting and light piping applications
Subminiature dome package
diffused dome for wide viewing angle
nondiffused dome for high brightness
TTL and LSTTL compatible 5 volt resistor lamps
Available in six colors
Ideal for space limited applications
Axial leads
Available with lead configurations for surface mount
and through hole PC board mounting
Description
Flat Top Package
The HLMP-Pxxx Series flat top lamps use an untinted,
nondiffused, truncated lens to provide a wide
radiation pattern that is necessary for use in
backlighting applications. The flat top lamps are also
ideal for use as emitters in light pipe applications.
Dome Packages
The HLMP-6xxx Series dome lamps for use as
indicators use a tinted, diffused lens to provide a
wide viewing angle with a high on-off contrast ratio.
High brightness lamps use an untinted, nondiffused
lens to provide a high luminous intensity within a
narrow radiation pattern.
Resistor Lamps
The HLMP-6xxx Series 5 volt subminiature lamps
with built in current limiting resistors are for use in
applications where space is at a premium.
Lead Configurations
All of these devices are made by encapsulating LED
chips on axial lead frames to form molded epoxy
subminiature lamp packages. A variety of package
configuration options is available. These include
special surface mount lead configurations, gull wing,
yoke lead or Z-bend. Right angle lead bends at 2.54
mm (0.100 inch) and 5.08 mm (0.200 inch) center
spacing are available for through hole mounting. For
more information refer to Standard SMT and Through
Hole Lead Bend Options for Subminiature LED Lamps
data sheet.
HLMP-Pxxx
Subminiatur e LED Lamps
Data Sheet
2
Device Selection Guide
Part Number: HLMP-xxxx
DH AS High High Device
Standard AlGaAs Efficiency Perf. Emerald Outline
Red Red Red Orange Yellow Green Green Device Description[1] Drawing
P005 P105 P205 P405 P305 P505 P605 Untinted, Nondiffused, A
Flat Top
P102 P202 P402 P302 P502 Untinted, Diffused, Flat Top A
6000 Q100 6300 Q400 6400 6500 Q600 Tinted, Diffused B
Q105 6305 Q405 6405 6505 Q605 Untinted, Nondiffused, B
High Brightness
Q150 7000 7019 7040 Tinted, Diffused, Low Current B
Q155 Nondiffused, Low Current B
6600 6700 6800 Tinted, Diffused, Resistor, B
5 V, 10 mA
6620 6720 6820 Diffused, Resistor, 5 V, 4 mA B
Ordering Information
HLMX-XXXX-X X X X X
4 x 4 Prod.
Part
Number
Min. Iv Bin
Max. Iv Bin
Color Bin
Selection
Packaging
Option
3
0.50 (0.020) REF.
0.94
1.24 (0.037)
(0.049)
2.92 (0.115)
MAX.
0.76
0.89 (0.030)
(0.035)R.
0.63
0.38(0.025)
(0.015)
2.03 (0.080)
1.78 (0.070)
0.79 (0.031)
0.53 (0.021)
0.46
0.56(0.018)
(0.022)
0.25 (0.010) MAX.
NOTE 2
0.20 (0.008) MAX.
CATHODE
1.65
1.91(0.065)
(0.075)DIA.
ANODE
11.68
10.67(0.460)
(0.420)
BOTH SIDES
0.18
0.23(0.007)
(0.009)
2.08
2.34(0.082)
(0.092)
CATHODE
STRIPE
2.21
1.96(0.087)
(0.077)
(B) Diffused and Nondiffused
Figure 1. Proper right angle mounting to a PC board to prevent protruding cathode tab from shorting to anode connection.
Package Dimensions
(A) Flat Top Lamps
NO. ANODE DOWN. YES. CATHODE DOWN.
CATHODE
TAB
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD
POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.
0.46
0.56 (0.018)
(0.022)
1.40
1.65(0.055)
(0.065)
0.25 (0.010) MAX.
NOTE 2
0.20 (0.008) MAX.
0.50 (0.020) REF.
CATHODE
1.65
1.91(0.065)
(0.075)DIA.
ANODE
11.68
10.67(0.460)
(0.420)
BOTH SIDES
1.14
1.40 (0.045)
(0.055) 0.63
0.38 (0.025)
(0.015)
2.21
1.96(0.087)
(0.077)
0.18
0.23(0.007)
(0.009)
0.79 (0.031) MAX.
2.44
1.88(0.096)
(0.074)
2.08
2.34(0.082)
(0.092)
CATHODE
STRIPE
4
Absolute Maximum Ratings at TA = 25°C
DH AS High
Standard AlGaAs Eff. High Perf. Emerald
Parameter Red Red Red Orange Yellow Green Green Units
DC Forward Current[1] 50 30 30 30 20 30 30 mA
Peak Forward Current[2] 1000 300 90 90 60 90 90 mA
DC Forward Voltage 6 6 6 6 V
(Resistor Lamps Only)
Reverse Voltage (IR = 100 µA) 5 5 5 5 5 5 5 V
Transient Forward Current[3] 2000 500 500 500 500 500 500 mA
(10 µs Pulse)
Operating Temperature Range:
Non-Resistor Lamps -55 to +100 -40 to +100 55 to +100 -40 to +100 -20 to +100 °C
Resistor Lamps -40 to +85 -20 to +85
Storage Temperature Range -55 to +100 °C
For Thru Hole Devices 260°C for 5 seconds
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices: 260°C for 20 seconds
Reflow Soldering Temperature
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this
high current.
5
Electrical/Optical Characteristics, TA = 25°C
Standard Red
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
6000-E00xx 0.63 1.2
6000-G00xx Luminous Intensity[1] IV1.60 3.2 mcd IF = 10 mA
P005-F00xx 1.0 2.5
Forward Voltage VF1.4 1.6 2.0 V IF = 10 mA
All Reverse Breakdown VR5.0 12.0 V IR = 100 µA
Voltage
6000 Included Angle Between 2q1/290 Deg.
P005 Half Intensity Points[2] 125
Peak Wavelength lPEAK 655 nm
Dominant Wavelength[3] ld640 nm
Spectral Line Half Width Dl1/2 24 nm
All Speed of Response ts15 ns
Capacitance C 100 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead
Luminous Efficacy[4] hv65 lm/W
6
DH AS AlGaAs Red
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P102-F00xx 1.0 20.0
P105-L00xx 10.0 30.0
P105-NP000 25 80
Q100-M00xx 16 45
Q100-N00xx Luminous Intensity IV25.0 45.0 mcd IF = 20 mA
Q100-PQ000 40 125
Q105-P00xx 40 200
Q105-ST000 160 500
Q150-F00xx 1.0 1.8 IF = 1 mA
Q155-F00xx 1.0 4.0
Q100 Forward Voltage VF1.8 2.2 VIF = 20 mA
Q150/Q155 1.6 1.8 IF = 1 mA
All Reverse Breakdown Voltage VR5.0 15.0 V IR = 100 µA
P105 125
Q100/Q150 Included Angle Between 2q1/290 Deg.
Q105/Q155 Half Intensity Points[2] 28
Peak Wavelength lPEAK 645 nm Measured at Peak
Dominant Wavelength[3] ld637 nm
Spectral Line Half Width Dl1/2 20 nm
All Speed of Response ts30 ns Exponential Time
Constant; e-t/ts
Capacitance C 30 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to Cathode Lead
Luminous Efficacy[4] hv80 lm/W
7
High Efficiency Red
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P202-F00xx 1.0 5.0
P205-F00xx 1.0 8.0
P205-JK000 4.0 12.5 IF = 10 mA
6300-F00xx 1.0 10.0
6300-KL000 Luminous Intensity[1] IV6.3 20.0 mcd
6305-L00xx 10.0 40.0
7000-D00xx 0.4 1.0 IF = 2 mA
6600-G00xx 1.6 5.0 VF = 5.0 Volts
6620-F00xx 1.0 2.0
All Forward Voltage VF1.5 1.8 3.0 V IF = 10 mA
(Nonresistor Lamps)
6600 Forward Current IF9.6 13.0 mA VF = 5.0 V
6620 (Resistor Lamps) 3.5 5.0
All Reverse Breakdown Voltage VR5.0 30.0 V IR = 100 µA
P205 125
6305 Included Angle Between 2q1/228 Deg.
All Diffused Half Intensity Points[2] 90
Peak Wavelength lPEAK 635 nm Measured at Peak
Dominant Wavelength[3] ld626 nm
Spectral Line Half Width Dl1/2 40 nm
All Speed of Response ts90 ns
Capacitance C 11 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead
Luminous Efficacy[4] hv145 lm/W
8
Orange
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P402-F00xx 1.0 4.0
P405-F00xx 1.0 6
P405-JK000 Luminous Intensity IV4.0 12.5 mcd IF = 10 mA
Q400-F00xx 1.0 8
Q405-H00xx 2.5 14
All Forward Voltage VF1.5 1.9 3.0 V IF = 10 mA
Reverse Breakdown Voltage VR5.0 30.0 V IR = 100 µA
P40x Included Angle Between 2q1/2125 Deg.
Q40x Half Intensity Points[2] 90
Peak Wavelength lPEAK 600 nm
Dominant Wavelength[3] ld602 nm Measured at Peak
Spectral Line Half Width Dl1/2 40 nm
All Speed of Response ts260 ns
Capacitance C 4 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead
Luminous Efficacy[4] hv380 lm/W
9
Yellow
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P302-F00xx 1.0 3.0
P305-F00xx 1.0 4.0
6400-F00xx 1.0 9.0
6400-JK000 4.0 12.5 IF = 10 mA
6405-J00xx Luminous Intensity[1] IV3.6 20 mcd
6405-MN0xx 16 50
7019-D00xx 0.4 0.6 IF = 2 mA
6700-G00xx 1.4 5.0 VF = 5.0 Volts
6720-F00xx 0.9 2.0
All Forward Voltage VF2.0 2.4 V IF = 10 mA
(Nonresistor Lamps)
6700 Forward Current IF9.6 13.0 mA VF = 5.0 V
6720 (Resistor Lamps) 3.5 5.0
All Reverse Breakdown VR5.0 50.0 V
Voltage
P305 Included Angle Between 125
6405 Half Intensity Points[2] 2q1/228 Deg.
All Diffused 90
Peak Wavelength lPEAK 583 nm Measured at Peak
Dominant Wavelength[3] ld585 nm
Spectral Line Half Width Dl1/2 36 nm
All Speed of Response ts90 ns
Capacitance C 15 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead
Luminous Efficacy[4] hv500 lm/W
10
High Performance Green
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P502-F00xx 1.0 3.0
P505-G00xx 1.6 6.3 IF = 10 mA
6500-F00xx 1.0 7.0
6505-L00xx Luminous Intensity[1] Iv10.0 40.0 mcd
7040-D00xx 0.4 0.6 IF = 2 mA
6800-G00xx 1.6 5.0 VF = 5.0 Volts
6820-F00xx 1.0 2.0
All Forward Voltage VF2.1 2.7 V IF = 10 mA
(Nonresistor Lamps)
6800 Forward Current IF9.6 13.0 mA VF = 5.0 V
6820 (Resistor Lamps) 3.5 5.0
All Reverse Breakdown Voltage VR5.0 50.0 V IR = 100 µA
P505 Included Angle Between 125
6505 Half Intensity Points[2] 2q1/228 Deg.
All Diffused 90
Peak Wavelength lPEAK 565 nm
Dominant Wavelength[3] ld569 nm
Spectral Line Half Width Dl1/2 28 nm
All Speed of Response ts500 ns
Capacitance C 18 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead
Luminous Efficacy[4] hv595 lm/W
Notes:
1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous intensity for an array
determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching between arrays.
2. q1/2 is the off-axis angle where the luminous intensity is half the on-axis value.
3. Dominant wavelength, ld, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines the color of the device.
4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie = Iv/hv, where Iv is the luminous intensity in
candelas and hv is the luminous efficacy in lumens/watt.
11
Emerald Green[1]
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P605-F00xx 1.0 1.5
Q600-F00xx Luminous Intensity IV1.0 1.5 mcd IF = 10 mA
Q605-F00xx 1.0 7.5
All Forward Voltage VF2.2 3.0 V IF = 10 mA
Reverse Breakdown Voltage VR5.0 V IR = 100 µA
P605 Included Angle Between 2q1/2125 Deg.
Q60x Half Intensity Points[2] 90
Peak Wavelength lPEAK 558 nm
Dominant Wavelength[3] ld560 nm Measured at Peak
Spectral Line Half Width Dl1/2 24 nm
P605/Q600 Speed of Response ts3100 ns
Capacitance C 35 pF VF = 0; f = 1 MHz
Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead
Luminous Efficacy[4] hV656 lm/W
Note:
1. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation.
12
Standard Red, DH As AlGaAs Red
Standard Red and DH AS
AlGaAs Red High Efficiency Red, Orange,
Yellow, High Performance
Green, and Emerald Green
HER, Orange, Yellow, and
High Performance Green,
and Emerald Green
Low Current
Figure 1. Relative intensity vs. wavelength.
Figure 2. Forward current vs. forward voltage (non-resistor lamp).
Figure 3. Relative luminous intensity vs. forward current (non-resistor lamp).
FORWARD CURRENT – mA
100
0
FORWARD VOLTAGE – V
80
60
50
70
20
0
10
30
40
0.5 1 1.5 2 2.5 3 3.5
90
HIGH
PERFORMANCE
GREEN,
EMERALD
GREEN
YELLOW
HIGH EFFICIENCY
RED/ORANGE
13
Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current (non-resistor lamps).
Figure 5. Maximum forward dc current vs. ambient temperature. Derating based on TJ MAX = 110°C (non-resistor lamps).
Figure 6. Maximum tolerable peak current vs. pulse duration (IDC MAX as per MAX ratings) (non-resistor lamps).
Standard Red
DH As AlGaAs RedStandard Red
HER, Orange, Yellow, and High
Performance Green DH As AlGaAs Red
HER, Orange, Yellow, and
High Performance Green,
and Emerald Green
14
Figure 9. Relative intensity vs. angular displacement.
Figure 7. Resistor lamp forward current vs. forward voltage. Figure 8. Resistor lamp luminous intensity vs. forward voltage.
15
Intensity Bin Limits
Bin Min. Max.
A 0.10 0.20
B 0.16 0.32
C 0.25 0.50
D 0.40 0.80
E 0.63 1.25
F 1.00 2.00
G 1.60 3.20
H 2.50 5.00
J 4.00 8.00
K 6.30 12.50
L 10.00 20.00
M 16.00 32.00
N 25.00 50.00
P 40.00 80.00
Q 63.00 125.00
R 100.00 200.00
S 160.00 320.00
T 250.00 500.00
U 400.00 800.00
V 630.00 1250.00
W 1000.00 2000.00
X 1600.00 3200.00
Y 2500.00 5000.00
Color Bin Limits
Package Bin Min. Max.
Emerald Green 0 Full Distribution
9552 556
8555 559
7558 562
6561 565
Green 0 Full Distribution
6561 565
5564 568
4567 571
3570 574
2573 577
Yellow 0 Full Distribution
1581.5 585.0
3584.0 587.5
2586.5 590.0
4589.0 592.5
5591.5 593.5
6591.5 595.0
7594.0 597.5
Orange 0 Full Distribution
1596.5 600.0
2599.0 602.5
3601.5 604.0
4603.8 608.2
5606.8 611.2
6609.8 614.2
7612.8 617.2
8615.8 620.2
Ordering Information
HLMx-XXXX-X X X X X
4 x 4 Prod.
Part
Number
Min. Iv Bin
Max. Iv Bin
Color Bin
Selection
Packaging
Option
Mechanical Option
00 Straight Leads, Bulk Packaging, Quantity of 500 Parts
10 Right Angle Housing, Bulk Packaging, Quantity of 500 Parts
11 Gull Wing Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel
12 Gull Wing Lead, Bulk Packaging, Quantity of 500 Parts
14 Gull Wing Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel
21 Yoke Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel
22 Yoke Leads, Bulk Packaging, Quantity of 500 Parts
24 Yoke Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel
31 Z-Bend Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel
32 Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts
34 Z-Bend Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel
1L 2.54 mm (0.100 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)
1S 2.54 mm (0.100 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)
2L 5.08 mm (0.200 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)
2S 5.08 mm (0.200 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)
Note:
All Categories are established for classification of products. Products may not be available in all categories.
Please contact your local Avago representative for further clarification/information.
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries.
Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5988-6260EN
5989-1708EN April 11, 2006