TD62008APG/AFG TOSHIBA BIPOLAR DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC TD62008APG,TD62008AFG 7CH DARLINGTON SINK DRIVER The TD62008APG and TD62008AFG are high-voltage, high-current darlington drivers comprised of seven NPN darlington pairs. All units feature integral clamp diodes for switching inductive loads and protective diodes against a negative input voltage. The TD62008APG and TD62008AFG are suitable for interfaces from plus and minus dual supply voltage systems to plus single supply voltage systems. Applications include relay, hammer, lamp and display (LED) drivers. Please observe the thermal conditions for use. The suffix (G) appended to the part number represents a RoHS product. TD62008APG TD62008AFG Features z Output current (single output) 400 mA (Max) z High sustaining voltage output 50 V (Min) z Output clamp diodes z Protective diodes against a negative input voltage z Inputs base resistor RIN = 20 k Weight DIP16-P-300-2.54A : 1.11 g (typ.) SOP16-P-225-1.27 : 0.16 g (typ.) z Inputs compatible with 9~15 V PMOS, CMOS. z Package type-APG : DIP-16 pin z Package type-AFG : SOP-16 pin Pin Connection (top view) Schematics (each driver) Note: 1 The input and output parasitic diodes cannot be used as clamp diodes. 2007-10-16 TD62008APG/AFG Absolute Maximum Ratings (Ta = 25C) CHARACTERISTIC SYMBOL RATING UNIT VCE (SUS) -0.5 ~ 50 V Output Current IOUT 400 mA / ch Input Voltage VIN -40 ~ 40 V Clamp Diode Reverse Voltage VR 50 V 400 mA Output Sustaining Voltage Clamp Diode Forward Current Power Dissipation APG AFG IF 1.47 PD 0.625 (Note) W Operating Temperature Topr -40 ~ 85 C Storage Temperature Tstg -55 ~ 150 C Note: On Glass Epoxy PCB (30 x 30 x 1.6 mm Cu 50%) Operating Conditions (Ta = -40 ~ 85C) CHARACTERISTIC SYMBOL Output Sustaining Voltage CONDITION MIN TYP. MAX UNIT 0 50 V DC 1 Circuit, Tpw = 25%, Duty = 40% 0 400 Tpw = 25 ms, Duty = 10%, 7 Circuits 0 200 VCE (SUS) mA Output Current IOUT Input Voltage VIN -35 35 V Clamp Diode Reverse Voltage VR 50 V Clamp Diode Forward Current IF 400 mA 0.52 0.325 Power Dissipation Note: APG AFG PD Ta = 85C (Note) W On Glass Epoxy PCB (30 x 30 x 1.6 mm Cu 50%) 2 2007-10-16 TD62008APG/AFG Electrical Characteristics (Ta = 25C) SYMBOL TEST CIR- CUIT ICEX 1 Collector-Emitter Saturation Voltage VCE (sat) 2 "H" Level IIN (ON) 4 "L" Level IIN (OFF) 4 VIN = -35 V hFE 3 VCE = 4 V, IOUT = 350 mA Clamp Diode Reverse Current IR 5 Clamp Diode Forward Voltage VF Turn-On Delay tON CHARACTERISTIC Output Leakage Current Input Current DC Current Transfer Ratio Turn-Off Delay TEST CONDITION MIN TYP. MAX UNIT VOUT = 50 V 100 A IOUT = 400 mA 1.3 2.4 IOUT = 200 mA 1.0 1.6 VIN = 18 V 0.85 1.8 VIN = 35 V 3.8 V mA -20 1000 3000 VR = 50 V, VR = 35 V (Type-F) 100 A 6 IF = 400 mA 1.5 2.4 V VOUT = 50 V, RL = 156 0.1 s 7 CL = 15 pF VOUT = 50 V, RL = 156 0.2 s tOFF 3 A 2007-10-16 TD62008APG/AFG Test Circuit 1. ICEX 2. VCE (sat) 3. hFE 4. IIN (ON), IIN (OFF) 5. IR 6. VF 7. tON, tOFF Note 1: Pulse Width 50 s Duty Cycle 10% Output Impedance 50 tr 5 ns, tf 10 ns Note 2: CL includes probe and jig capacitance Precautions for Use This IC does not include built-in protection circuits for excess current or overvoltage. If this IC is subjected to excess current or overvoltage, it may be destroyed. Hence, the utmost care must be taken when systems which incorporate this IC are designed. Utmost care is necessary in the design of the output line, COMMON and GND line since the IC may be destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding. 4 2007-10-16 TD62008APG/AFG Type-APG Free Air Type-AFG Free Air Type-APG On Glass Epoxy PCB 30x30x16mm Cu 50% 5 2007-10-16 TD62008APG/AFG Package Dimensions DIP16-P-300-2.54A Unit : mm Weight: 1.11 g (Typ.) 6 2007-10-16 TD62008APG/AFG Package Dimensions SOP16-P-225-1.27 Unit : mm Weight: 0.16 gTyp.) 7 2007-10-16 TD62008APG/AFG Notes on Contents 1. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 2. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause breakdown, damage or deterioration of the device, and may result in injury by explosion or combustion. (2) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of overcurrent and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load. A breakdown could cause a large current to continuously flow and lead to smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings are required, such as fuse capacity, fusing time and insertion circuit location. (3) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. (4) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause breakdown, damage or deterioration of the device, and may result injury by explosion or combustion. In addition, do not use any device that has had current applied even once while inserted in the wrong orientation or incorrectly . (5) Carefully select external components such as power amps and regulators (including input and negative feedback capacitors), and load components such as speakers. If there is a large amount of leakage current, such as from input or negative feedback condensers, the IC output DC voltage will increase. If this output voltage is connected to a speaker with a low input voltage threshold, overcurrent or IC failure could cause smoke or ignition. (The overcurrent can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage directly to a speaker. 8 2007-10-16 TD62008APG/AFG Points to Remember on Handling of ICs (1) Heat Radiation Design When using an IC with a large current flow, such as in a power amp, regulator or driver, please design the device so that heat is appropriately radiated, so as not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into consideration the effect of IC heat radiation on peripheral components. (2) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, current flows back to the motor's power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device's motor power supply and output pins might be exposed to conditions beyond absolute maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. About solderability, following conditions were confirmed * Solderability (1) Use of Sn-37Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux 9 2007-10-16 TD62008APG/AFG RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 10 2007-10-16