QVGA module with 400 nits brightness and
550:1 contrast. An LED backlight along with
high-purity color filters give excellent color
reproduction. Module carries Sharp’s
Strong 2 Rating for temperature, shock
tolerance, and brightness and contrast.
Non-touch-panel version
of LQ057Q3DG01.
Full Specifications Listing
LQ057Q3DG02 LCD Module
Product Specification
June 2009
LCD Specification
LCD Group
Technical Document
LD-21605A－1
NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no
part of this pub lication may be reproduced or transmitted in any form or by any means, electronic o r mechanical for any
purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also
required before any use of this publication may be made by a third party.
The application circuit examples in this publication are provided to explain the representative applications of SHARP's
devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be
executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party
resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in
equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the
latest device specification sheets before using any SHARP's device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other
contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to
obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to
change without notice.
Observe the following points when using any device in this publication. SHARP takes no responsibility for damage
caused by improper use of the devices.
The devices in this publication are designed for general electronic equipment use.
The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for
equipment such as:
・Transportation control and safety equipment(i.e.,aircraft, trains, automobiles, etc.)
・Traffic signals・Gas leakage sensor breakers ・Alarm equipment・Various safety devices etc.
SHARP's devices shall not be us ed for equipment that requires extremely high level of reliability, such as:
・Military and space applications ・Nuclear power control equipment
・Medical equipment for life support
Contact a SHARP representative, in advance, when intending to use SHARP’s devices for any “specific” applications
other than those recommended by SHARP.
Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
LD-21605A－2
1. Application
This specification applies to color TFT-LCD module, LQ057Q3DG02.
2. Summary and Features
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is
composed of a color TFT-LCD panel, driver ICs, control circuit (PWB), FPC, front and back polarizer, sealed case,
backlight unit. Graphics and texts can be displayed on a 320×RGB×240 dots panel with 262,144 colors by suitable
control supplying from the outside.
It isn’t composed
LED drive circuit for a backlight drive.
・ Wide Viewing Angle technology is adopted.
(The most suitable viewing angle is in the 12 o'clock direction.)
・ By adopting an active matrix drive, a picture with high contrast is realized.
・ Reflection due to external light is minimized through the use of a low reflection black matrix .
・ A thin, light and compact module is accomplished through the use of COG mounting technology.
・ Through the use of high color purity color filter and TN-normally white mode excelled in color
reproducibility, an image with highly natural color reproduction is realized.
・ High viewing angle and high brightness.
・ An inverted video display in the vertical / horizontal directions is possible.
・ This module is adapted to RoHS compliance.
3. Mechanical specifications
table 3-1
Parameter Specifications Units
Screen size 14.4 (5.7 inch) diagonal cm
Active area 115.2 (H) × 86.4 (V) mm
Display format 320(H)×240(V) pixels
(1 pixel = R + G + B dots)
Dot pitch 0.360 (H) × 0.360 (Ｖ) mm
Pixel configuration R,G,B Stripe configuration
Display mode Normally white
Outline dimension【Note1-1】 144.0 (W)×104.6 (H)×12.3(D) mm
Mass 210 (MAX) g
【Note 1-1】
A FPC of LED and some projections are excluded.
A figure of outline dimension is show n in Fig. 1.
LD-21605A－3
４. Input terminal
4-1. TFT-LCD panel driving part
CN1 Used connector: IMSA-9637S-33Y902 (IRISO ELECTRONICS CO.,LTD.)
Table 4-1 Functional table of CN1 terminals
Pin No. Symbol Description Polarity
１ GND ground
２ CK Clock signal for sampling each data signal
３ Hsync Horizontal synchronous signal Negative
４ Vsync Vertical synchronous signal Negative
５ GND ground
６ R0 RED data signal(LSB)
７ R1 RED data signal
８ R2 RED data signal
９ R3 RED data signal
１０ R4 RED data signal
１１ R5 RED data signal(MSB)
１２ GND ground
１３ G0 GREEN data signal(LSB)
１４ G1 GREEN data signal
１５ G2 GREEN data signal
１６ G3 GREEN data signal
１７ G4 GREEN data signal
１８ G5 GREEN data signal(MSB)
１９ GND ground
２０ B0 BLUE data signal(LSB)
２１ B1 BLUE data signal
２２ B2 BLUE data signal
２３ B3 BLUE data signal
２４ B4 BLUE data signal
２５ B5 BLUE data signal(MSB)
２６ GND ground
２７ ENAB Signal to settle the ho rizontal display position【Note4-1】 Positive
２８ Vcc +3.3V power supply
２９ Vcc +3.3V power supply
３０ R/L Selection signal for horizontal scanning direction【Note4-2】
(“L” : Normally , “H” : Right-and-Left reversal)
３１ U/D Selection signal for vertical scanning direction【Note4-2】
(“H” : Normally , “L” : Up-and-Down reversal)
３２ GND ground
３３ GND ground
LD-21605A－4
【Note 4-1】The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. Don’t keep
ENAB “Low” during operation.
【Note 4-2】
R/L = L，U/D = H R/L = H，U/D = H
R/L = L，U/D = L R/L = H，U/D = L
4-2. LED Backlight driving part (FPC1)
Table 4-2 Functional table of FPC terminals
Pin No. Symbol Description
１ LED-A1 Power Supply for LED (Anode)
２ LED-C1 Power Supply for LED (Cathode)
３ LED-A2 Power Supply for LED (Anode)
４ LED-C2 Power Supply for LED (Cathode)
５ LED-A3 Power Supply for LED (Anode)
６ LED-C3 Power Supply for LED (Cathode)
７ LED-A4 Power Supply for LED (Anode)
８ LED-C4 Power Supply for LED (Cathode)
Suitable connector ：IMSA-9632S-08-AGF
LD-21605A－5
5. Ab solute maximum rati ngs
Table 5-1
Item Symbol Conditions Rated value Unit Remarks
Input voltage VI Ta = 25°C-0.3 ~ VCC +0.3 V 【Note 5-1】
Power supply voltage VCC Ta = 25°C-0.3 ~ +4.0 V
Temperature for storage Tstg - -30 ~ +70 °C 【Note 5-2,3】
Temperature for operation Topr - -30 ~ +70 °C 【Note 5-2,3,4】
【Note 5-1】 CK, R0～R5, G0～G5, B0～B5, Hsync, Vsync, ENAB, R/L, U/D
【Note 5-2】 This rating applies to all parts of the module and should not be exceeded.
【Note 5-3】 Maximum wet-bulb temperature is less than 39℃. Condensation of dew must be avoided as
electrical current leaks will occur, causing a degradation of performance specifications.
【Note 5-4】 The operating temperature only guarantees operation of the circuit. For contrast, speed response,
and other factors related to display quality, judgment is done using the ambient temperature
Ta =+25℃.
LD-21605A－6
6. Electrical characteristics
6-1. TFT-LCD panel driving section
Table 6-1 Ta=25℃
Parameter Symbol Min. Typ. Max. Unit Remarks
+3.3V Supply voltage Vcc +3.0 +3.3 +3.6 V
【Note 6-1】
power suply Current dissipation Icc － 20 30 mA 【Note 6-2】
Permissive input ripple VRF － － 100
mVp-p
Vcc=+3.3V
Input Low voltage VIL 0 － 0.1Vcc V
Input High voltage VIH 0.9Vcc － Vcc V
【Note 6-3】
Input leak current (Low) IOL － － 1 μA V
I=0V
【Note 6-3】
Input leak current (High) IOH － － 1 μA VI=3.3～Vcc
【Note 6-3】
【Note 6-1】
Vcc turn-on/off conditions.
t1 t2 t3
0.3V
3.0V 3.0V
Vcc
Signal
t5
0.3V 0.3V
t4
t1≦10 ms
0<t2≦100 ms
0<t3≦100 ms
0<t4≦50 ms
1000 ms<t5
Vcc-dip conditions
1) 2.4V ＜ Vcc ＜ 3.0V
td ≦ 10 ms
2) At Vcc ＜ 2.5V
Vcc-dip conditions should also follow the Vcc turn-on/off td
2.4V
3.0V
Vcc
conditions.
【Note 6-2】 Vcc = 3.3V
Max current situation : Timing ; Typical, Pattern ; All black
【Note 6-3】 CK,R0～R5,G0～G5,B0～B5,Hsync,Vsync,ENAB,R/L,U/D
LD-21605A－7
6-2. Backlight driving section
The backlight system is edge-lighting type with 20 White-LED(White Light Emitting Diode).
The characteristics of White-LED are shown in the following table. (Ta = 25 deg.)
Table 6-2
Parameter Min. Typ. Max. Unit Remark
LED voltage - 16.0 17.5 V LED current = 20mA
LED current range - 20 20 mA
Number of circuit strings - 4 - [Note 1]
LED power consumption - 1.28 - W [Note 2]
LED life time - 30,000 - Hour continuous operation
[Note 1] The LED backlight is composed by 4 strings from which 5 LED is connected with the series.
The figure below shows the circuit chart.
In each string, there is a ceramic capacitor for the electrostatic protection.
LED-A1 LED-A3
LED-C1 LED-C3
LED-A2 LED-A4
LED-C2 LED-C4
[Note 2] Calculated value for reference ( IL × VL )
7. Timing Characteristics of input signals
Timing diagrams of input signal are shown in Fig.7
7-1. Timing characteristics
Table 7-1
Parameter Symbol MIN TYP MAX Unit Remarks
Clock frequency 1/Tc - 6.3 7.0 MHz
Duty ratio TH/T 40 50 60 %
Data Setup time Tds 10 - - ns
Hold time Tdh 10 - - ns
TH 50.0 63.6 - μs Cycle 360 400 450 clock
Horizontal sync.
signal
Pulse width THp 1 - 6 clock
Vertical sync. Cycle TV 251 262 280 line
signal frequency 1/TV 50 60 - Hz
【Note7-1】
Pulse width TVp 1 - 6 line
Horizontal display period THd 320 320 320 clock
Hsync-Clock phase difference THc 5 - - ns
Hsync-Vsync phase difference TVh 0 - 320 clock
Vertical display start position TVs 7 7 7 line
【Note7-1】 In case of lower frequency, the deterioration of display quality, flicker etc., may occur.
Please use this module in more than 50Hz.(1/Tv)
LD-21605A－8
7-2. Horizontal display position
Table 7-2 Parameter symbol Min. Typ. Max. Unit Remark
Enable signal Setup time Tes 10 - - ns
Pulse width Tep 320 - - clock
Hsync-Enable signal phase
difference The 7 7 7 clock
Please do not make ENAB fixation in "L".
The Horizontal display start position (The) is fixed 7 clock.
7-3. Vertical display position
The Vertical display start position (TVs) is fixed 7 line.
ENAB signal has no relation to the vertical display position.
7-4. Input Data Signals and Display Position on the screen
ＵＰ
D1,DH1
D1,DH2
D1,DH3
D1,DH240
D2,DH1
D320,DH240
D320,DH1
D2,DH2
R
D3,DH1
G
B
Display position of input data (H,V)
LD-21605A－10
(８) Input Signals, Basic Display Color and Gray Scale of Each Color
Colors & Data signal
Gray scale
Gray Scale
R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Black － 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue － 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Green － 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Cyan － 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Red － 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Magenta － 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Yellow － 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
Basic color
White － 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× È È È È
Ø È È È È
Brighter GS61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Ø GS62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Gra
y
Scale of red
Red GS63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0
Darker GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0
× È È È È
Ø È È È È
Brighter GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0
Ø GS62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0
Gra
y
Scale of
g
reen
Green GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
× È È È È
Ø È È È È
Brighter GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1
Ø GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1
Gra
y
Scale of bleu
Bleu GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
0 :Low level voltage 1 :High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18
bit data signals, the 262,144-color display can be achieved on the screen.
LD-21605A－11
9. Optical characteristics
Table 9-1 Ta=25℃, VCC =+3.3V
Parameter Symbol Condition Min Typ Max Unit Remarks
θ
21,
θ
22
75 80
－ °(degree) 【Note 9-1】
Viewing angle range θ11 CR≧5 75 80
－ °(degree)
θ12 55 65
－ °(degree)
Contrast ratio CRmax Optimal
viewing angle 440 550 － 【Note 9-2】
Response Rise τr θ＝０° － 30 － ms 【Note 9-3 】
time Fall τd － 10 － ms
White chromaticity x 0.263 0.313 0.363
y
0.279 0.329 0.379 【Note 9-4】
Luminance Y 320 400
－ cd/m2
Remarks:The optical specifications are measured 30 minute after turing LED on and in a dark room or equivalent
condition, according to the method shown in Fig.9-1 below.
Photodetector:SR-3(TOPCON)
Center of the screen
TFT-LCD Module LCD panel
Field=2°
400ｍｍ
Fig.9-1 Optical characteristics measurement method
LD-21605A－12
【Note 9-1】 Viewing angle range is defined as follows.
12 o’clock
direction
6 o’clock direction
Normal line
θ21
θ22
θ11
θ12
The best viewing angle of this module is slightly leaned to 12 o’clock from normal line.
Where θ11＞θmax, gray scale is reversed partially.
Where θ11＜θmax, or in θ12 direction, gray scale isn’t reversed.
【Note 9-2】 Contrast ratio is defined as follows:
Luminance (brightness) with all pixels white
Contrast ratio(CR)=
Luminance (brightness) with all pixels black
※ Measurement point : Center of the active area
【Note 9-3】 Response time is obtained by measuring the transition time of photo detector
output, when input signals are applied so as to make the area "black" to and
from "white".
０％
１０％
９０％
１００％
Black WhiteWhi t e
τｄ τｒ
Time
P
h
o
t
o
d
e
t
e
c
t
e
r
o
u
t
p
u
t
(
R
e
l
a
t
i
v
e
v
a
l
u
e
)
【Note 9-4】 This parameter should be measured at the center of the screen and 30 minutes after turn-on.
The characteristics are measured when the driver circuit is not powered.
【Note 9-5】 The data for LED is for your reference, because LED is consumable component.
LED life time : When a brightness of lamp surface become 50% of the initial value under the
Standard condition.
LD-21605A－13
10. Handling Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b)Our TFT-LCD module is designed to be fixed to the hardware with mounting holes on 4-corners on the
backside. Be sure to design the cabinet so that the module can be installed without any extra stress such
as warp or twist.
c) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
d) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
e) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Handle with care.
f) Since CMOS LSI is used in this module, take care of static electricity and ensure the human earth
when handling. Observe all other precautionary requirements in handling components.
g) Since there is a circuit board in the module back, stress shall not be impressed in designing and
assembling. If stress is impressed, there arises a possibility that circuit parts may be damaged.
h) Direct sunlight on LCD panel may cause degradation of panel quality. Do not expose the LCD panel to
direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such
environment.
i) Connect GND to 4 place of mounting holes to get stable against EMI and external noise.
j) When handling LCD modules and assembling them into cabinets, please be noted that long-term
storage in the environment of oxidization or deoxidization gas and the use of such materials as
reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and
discoloration of the LCD modules.
k) When installing LCD modules in the cabinet, we suggest the reference torque as 0.38±0.3N･m
(with JIS B1122 M3, 6mm).
Since the optimal torque varies according to the screw or building conditions, so be sure to test it
in the actual use condition.
Inserting length to the module shall be within 5mm. Tapping screws shall be tighten only one time.
More than two time tightening is not assured. Please take care in the case of reworking.
l) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it
gets inside your eye or mouth by mistake.
m) Notice: Never dismantle the module , because it will cause failure.
Please don't remove the fixed tape, insulating tape etc that was pasted on the original module.
(except for protection film of the panel and the crepe tape(yellow tape) temporarily adhered on the
module.)
n) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
（Please use a screen saver etc., in order to avoid an afterimage.）
o) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
If adjusted value is changed, the specification may not be satisfied.
p) If a minute particle get into the module and adheres on an optical material, it may cause display
irregularity issue, etc. Therefore, fine-pitch filters have to be built into cooling and inhalation hole if
you intend to install a fan.
q) Liquid crystal can be damaged by ultraviolet light. Be sure not to operate or storage under direct
sunlight or strong ultraviolet light for a long time.
r) Please storage modules in ambient temperature if possible. Below the storage temperature, liquid
crystal can freeze and damage the LCD panel. Above storage temperature, it can irreversibly turn into
isotropic state which cannot work as display.
s) Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and
oxime series), tray forming agent (azo compound) etc, in the cabinet or the packing materials may
induce abnormal display with polarizer film deterioration regardress of contact or noncontact to
polarizer film.
Be sure to confirm the component of them.
LD-21605A－14
12.Reliability Test Items
No. Test items Test conditions
１ High temperature
storage test
Leaves the module at Ta = +70℃ for 240h 【Note 1】
２ Low temperature
storage test
Leaves the module at Ta=－30℃ for 240h 【Note 1】
３ High temperature
and high humidity
operating test
Operates the module at Tp= +40℃, 95%RH for 240h
(No condensation) 【Note 1】
４ High temperature
operating test
Operates the module at Tp=+70°C for 240h 【Note 1】
５ Low temperature
operating test
Operates the module at Tp=－30℃ for 240h 【Note 1】
６ Strength against
ESD
±200V・200pF(0Ω) 1 time for each terminals
７ Shock test
(non-operating)
490m/s2・11ms, ±X；±Y；±Z once for each direction
８ Vibration test
(non-operating)
Frequency：5～57Hz, One side：0.076mm
Frequency：58～500Hz, Acceleration：9.8m/s2
Sweep cycle：11 minutes
X,Y,Z 1 hours for each directions ( total 3 hours ) 【Note 2】
９ Thermal shock test Ta=－30℃～+70℃ , 50 cycles
(0.5h) (0.5h)
【Result evaluation criteria】
Under the display quality test conditions with normal operation state, these shall be
no change which may affect practical display function.
【Note 1】 Ta= Ambient temperature, Tp= Panel surface temperature
【Note 2】 X,Y,Z directions are shown as follows:
ＸＹ
Ｚ
LD-21605A－15
13. Packing Form
1-1 packaging detail
Please refer “Figure A” for the detailed packing form.
1-2 Carton stock conditions
a) Maximum number of Carton being stuck: Max. 9 cartons
b) Maximum number of product contained: 20 Unit
c) Carton size: 534 mm(W)×349 mm(D)×195 mm(H)
d) Total mass : 7.6 kg (MAX)
e) Carton stock environment:
1) Temperature: 0 ~ 40°C
2) Humidity: Less than 60%RH
3) Ambiance: No gases bite into electronic components and wiring materials
4) Period: Approximately 3month
5) Unpacking: Take care not to get LCD module damaged by ESD.
When unpacking, the room humidity shall be controlled to be
more than 50%RH.
Please unpack packages by effective means against ESD
(the earthing Band, for example).
1-3 Barcode label print
Serial No. consists of 10 numbers. The role of each number is as follows:
1st: last number of the year of manufacture (0-9)
2nd: month of manufacture (1-9,X,Y,Z)
3rd-4th: SHARP handling No. (fixed value=0X)
5th: manufacturing location (fixed value=D)
6th-10th: serial No. (1-9)
ex. The 12th product of Dec. 2011 = 1Z0XD00012
Product number
Serial number
Barcode
LD-21605A－16
Master Carton
sleeve
Tray
5pcs+1pcs(blank cover)
Figure. A : packing form
Modules
MAX 4pcs/1tray
Barcode label
LD-21605A2
NORTH AMERICA
Sharp Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
www.sharpsma.com
TAIWAN
Sharp Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
CHINA
Sharp Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: smc@china.global.sharp.co.jp
EUROPE
Sharp Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
www.sharpsme.com
SINGAPORE
Sharp Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
KOREA
Sharp Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
JAPAN
Sharp Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
HONG KONG
Sharp-Roxy (Hong Kong) Ltd.
Level 26, Tower 1, Kowloon Commerce Centre,
No. 51, Kwai Cheong Road, Kwai Chung,
New Territories, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 602-603, 6/F.,
International Chamber of Commerce Tower,
168 Fuhua Rd. 3, CBD,
Futian District, Shenzhen 518048,
Guangdong, P.R. China
Phone: (86) 755-88313505
Fax: (86) 755-88313515
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for
limitations on special applications. See Limited Warranty for SHARP’s product warranty.
The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE,
ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in
any way, for any incidental or consequential economic or property damage.
LCD Group
LCD Specification
Technical Document