ALUMINUM ELECTROLYTIC CAPACITORS CD Chip Type, Low Impedance series Chip type, low impedance temperature range up to +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). CD UD Low Impedance Specifications Item Performance Characteristics Category Temperature Range - 55 ~ +105C Rated Voltage Range 6.3 ~ 100V Rated Capacitance Range 1 ~ 3300F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (A), whichever is greater. Measurement frequency : 120Hz, Temperature : 20C Rated voltage (V) tan (MAX.) tan 6.3 0.26 10 0.19 16 0.16 25 0.14 35 0.12 50 0.10 63 0.08 80 0.08 100 0.07 For capacitance of more than 1000F, add 0.02 for every increase of 1000F. Measurement frequency : 120Hz Rated voltage (V) Stability at Low Temperature 10 16 25 35 50 63 80 100 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 3 3 3 3 3 3 Z--25C / Z+20C Impecance ratio Z--40C / Z+20C ZT / Z20 (MAX.) Z--55C / Z+20C After 5000 hours' (2000 hours for L 10 mm: 50V 10mm: 63V or more) application of or less, and for L Endurance 6.3 rated voltage at 105C, capacitors meet the characteristics requirements listed at right. Capacitance Change Within 30% of initial value for capacitors tan 200% or less initial specified value 300% or less initial specified value for 63V or more Leakage current Initial specified value or less After storing the capacitors under no load at 105C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they will meet the specified value for endurance characteristics listed above. Shelf Life The capacitors shall be kept on the hot plate maintained at 250C for 30 seconds. After removing from the hot plate and restored Resistance to soldering heat at room temperature, they meet the characteristics requirements listed at right. Capacitance Change Within 10% of initial value tan Initial specified value or less Leakage current Initial specified value or less Black print on the case top. Marking Chip Type Type numbering system (Example : 16V 100F) (4 ~ 8 x 6.2) Positive Capacitance Lot No. L 0.3 2 3 4 5 6 7 8 9 Package code Size Package 4 ~ 10 Taping 12.5 ~ 18 Taping 12.5 ~ 18 Tray Capacitance tolerance (20%) 1: Size 8 x 6.2 only Rated Capacitance (100F) Positive E L 0.5 Negative H 0.3 MAX. Pressure relief vent Capacitance E B 0.2 D 0.5 nichicon 330 F CD 50V H0515 Lot No. (mm) DxL A B C E L H Dimension table in next page. DxL A B C E L H 5 x 5.8 6.3 x 5.8 6.3 x 7.7 8 x 6.2 4 x 5.8 8 x 10 10 x 10 2.4 2.4 2.1 1.8 3.3 2.9 3.2 6.6 6.6 5.3 4.3 8.3 8.3 10.3 6.6 6.6 5.3 4.3 8.3 8.3 10.3 2.2 2.2 1.3 1.0 2.3 3.1 4.5 7.7 5.8 5.8 5.8 6.2 10 10 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 12.5 x 13.5 16 x 16.5 18 x 16.5 6.4 5.4 4.8 19.1 17.1 13.6 19.1 17.1 13.6 6.3 6.3 4.0 16.5 16.5 13.5 1.0 ~ 1.4 1.0 ~ 1.4 1.0 ~ 1.4 Voltage L 0.5 Series A 0.2 A 0.2 C 0.2 0.5 MAX. Plastic platform Voltage D Code 4 ~ 6.3 CL 8 (6.2L) CL 8 (10L) * 10 NL 12.5~18 NQ Type Positive (12.5 ~ 18) Trade mark Rated voltage (16V) Series name A 0.2 A 0.2 Pressure relief vent Capacitance Lot No. C 0.2 B0.2 A2 220E CD Trade mark D 0.5 Series 0.5 MAX. Plastic platform 0.3 MAX. Code GS MS ZD Size code Configuration Negative H (8 x 10, 10 x 10) Voltage ( E : 25V ) 10 11 12 13 14 A 0.2 A 0.2 C 0.2 B 0.2 A2 47 j CD D 0.5 Series 1 Trade mark E Voltage ( j : 6.3V ) 1 UCD 1 C 1 0 1 M C L 1 GS 0.5 MAX. Plastic platform 0.3 MAX. H Negative V 6.3 10 16 25 35 50 63 80 100 Code j A C E V H J K 2A CAT.8100V-1 ALUMINUM ELECTROLYTIC CAPACITORS CD series Dimensions Cap. (F) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 5.8 2.70 60 2.2 2R2 4 5.8 2.70 60 3.3 3R3 4 5.8 2.70 60 4.7 4R7 60 10 100 15 4 150 22 220 27 270 33 330 47 4 4 5 5.8 5.8 5.8 1.35 90 1.35 90 0.70 5.8 1.35 90 5 5.8 0.70 160 5.8 1.35 5.8 0.70 160 4 5.8 1.35 90 5 5.8 0.70 160 6.3 5.8 90 5.8 1.35 90 4 5.8 1.35 90 5 5.8 0.70 160 5 5.8 0.70 160 6.3 0.36 1.35 4 90 5 160 4 470 4 5.8 5.8 0.36 1.35 5 5.8 0.70 160 5 5.8 0.70 160 6.3 5.8 0.36 240 5 5.8 0.70 160 6.3 5.8 0.36 240 240 5 5.8 0.70 160 6.3 5.8 0.36 240 240 5.8 4 6.3 5.8 0.36 4 5.8 1.35 90 4 5.8 2.70 4 5.8 1.35 90 5 5.8 1.50 90 5 5.8 0.70 160 6.3 5.8 0.86 170 5 5.8 0.70 160 6.3 5.8 0.86 170 5.8 6.3 195 0.36 240 7.7 0.66 6.3 8 6.2 0.63 200 6.3 7.7 0.66 195 8 6.2 0.63 200 8 10 0.32 350 90 240 6.3 5.8 0.36 240 56 560 5 5.8 0.70 160 6.3 5.8 0.36 240 6.3 5.8 0.36 240 6.3 5.8 0.36 240 68 680 6.3 5.8 0.36 240 6.3 5.8 0.36 240 6.3 5.8 0.36 240 6.3 5.8 0.36 240 6.3 7.7 0.32 290 5 5.8 0.70 160 6.3 7.7 0.32 290 6.3 7.7 0.32 290 6.3 5.8 0.36 240 8 6.2 0.26 300 8 10 0.16 600 6.3 5.8 0.36 240 8 10 0.16 600 8 10 0.16 600 10 10 0.16 700 8 10 0.16 600 8 10 0.16 600 10 10 0.16 700 10 0.08 850 12.5 13.5 0.12 900 12.5 13.5 0.12 13.5 0.08 1100 16 16.5 0.073 1610 16 16.5 0.073 1610 100 101 150 151 220 221 330 6.3 5.8 6.3 0.36 7.7 0.32 290 8 6.2 0.26 300 0.36 240 0.36 240 6.3 7.7 0.32 290 0.32 290 6.3 7.7 0.32 290 8 6.2 0.26 300 8 6.2 0.26 300 8 10 0.16 600 8 10 0.16 600 8 10 0.16 600 10 10 0.16 600 8 10 0.16 600 10 10 0.08 850 12.5 10 10 0.08 850 12.5 13.5 0.08 1100 16 16.5 0.035 1800 471 8 10 0.16 600 8 680 681 8 10 0.16 600 10 10 0.08 850 1000 102 8 10 0.16 600 10 10 0.08 850 1500 152 10 10 0.08 850 2200 222 13.5 0.08 1100 3300 332 Cap. (F) 12.5 12.5 63 80 1J 1K 4.7 4R7 10 22 100 5 5.8 3.00 50 5.8 1.50 6.3 7.7 1.20 120 8 6.2 1.20 120 6.3 220 0.08 12.5 13.5 0.08 1100 16 16.5 0.035 1800 Case size fD L Impedance Rated ripple 100 2A 5 5.8 5.00 25 6.3 5.8 3.00 40 6.3 7.7 2.40 60 8 6.2 2.40 60 8 10 1.30 130 80 900 1100 (mm) V 3R3 13.5 1100 Code 3.3 240 7.7 391 0.08 0.36 5.8 470 13.5 5.8 6.3 390 12.5 6.3 6.3 240 6.3 331 5.8 8 10 1.30 130 33 330 8 10 0.65 250 8 10 1.30 130 10 10 0.70 200 47 470 8 10 0.65 250 10 10 0.70 200 12.5 13.5 0.32 500 68 680 10 10 0.35 400 12.5 13.5 0.32 500 12.5 13.5 0.32 500 100 101 10 10 0.35 400 12.5 13.5 0.32 500 16 16.5 0.17 793 150 151 12.5 13.5 0.16 800 12.5 13.5 0.32 500 16 16.5 0.17 793 220 221 12.5 13.5 0.16 800 18 16.5 0.15 917 330 331 16.5 0.15 917 470 471 16 16.5 0.082 1410 680 681 18 16.5 0.08 1690 16 16.5 0.17 793 18 18 16.5 0.15 917 Case size fD L (mm) Impedance Rated ripple Max. Impedance (1/2) at 20C 100kHz, Rated Ripple (mArms) at 105C 100kHz : In this case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency 50Hz 120Hz 300Hz 1kHz 10kHz~ Coefficient 0.35 0.50 0.64 0.83 1.00 Taping specifications are given in page 24. Recommended land size, soldering by refrow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V-1