SCH1305 Ordering number : ENN7759 SCH1305 P-Channel Silicon MOSFET General-Purpose Switching Device Applications Featurest * Low ON-resistance. * High-speed switching. * 1.8V drive. Specifications Absolute Maximum Ratings at Ta=25C Parameter Symbol Conditions Ratings Unit Drain-to-Source Voltage VDSS --12 Gate-to-Source Voltage VGSS 10 V ID --1.5 A Drain Current (DC) Drain Current (Pulse) IDP PD Allowable Power Dissipation PW10s, duty cycle1% Mounted on a ceramic board (900mm20.8mm) V --6 A 0.7 W Channel Temperature Tch 150 C Storage Temperature Tstg --55 to +150 C Electrical Characteristics at Ta=25C Parameter Symbol Drain-to-Source Breakdown Voltage Ratings min ID=--1mA, VGS=0 VDS=--12V, VGS=0 VGS=8V, VDS=0 --12 IDSS IGSS VDS=--6V, ID=--1mA VDS=--6V, ID=--0.8A --0.3 Forward Transfer Admittance VGS(off) yfs Static Drain-to-Source On-State Resistance RDS(on)1 RDS(on)2 ID=--0.8A, VGS=--4.5V ID=--0.4A, VGS=--2.5V Input Capacitance RDS(on)3 Ciss ID=--0.1A, VGS=--1.8V VDS=--6V, f=1MHz Zero-Gate Voltage Drain Current Gate-to-Source Leakage Current Cutoff Voltage V(BR)DSS Conditions 1.08 typ max Unit V --10 A 10 A --1.0 V 235 310 m 335 470 m 445 670 m 1.8 S 160 pF VDS=--6V, f=1MHz VDS=--6V, f=1MHz 45 pF 35 pF Output Capacitance Coss Reverse Transfer Capacitance Crss Turn-ON Delay Time td(on) tr See specified Test Circuit 11 ns See specified Test Circuit 45 ns td(off) tf See specified Test Circuit 29 ns See specified Test Circuit 30 ns Rise Time Turn-OFF Delay Time Fall Time Marking : JE Continued on next page. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 52804 TS IM TA-100791 No.7759-1/4 SCH1305 Continued from preceding page. Parameter Symbol Ratings Conditions min typ Unit max Total Gate Charge Qg VDS=--6V, VGS=--4.5V, ID=--1.5A 2.6 nC Gate-to-Source Charge Qgs VDS=--6V, VGS=--4.5V, ID=--1.5A 0.25 nC Gate-to-Drain "Miller" Charge Qgd VDS=--6V, VGS=--4.5V, ID=--1.5A 0.65 Diode Forward Voltage VSD IS=--1.5A, VGS=0 Package Dimensions unit : mm 2221 VDD= --6V 6 5 4 ID= --0.8A RL=7.5 VIN 0.15 VOUT PW=10s D.C.1% 1.5 1.6 D 0.05 V 0V --4.5V Side View 0.2 0.05 --1.5 Switching Time Test Circuit VIN Top View 1.6 nC --0.92 Bottom View 0.56 0.25 Side View G 1 : Drain 2 : Drain 3 : Gate 4 : Source 5 : Drain 6 : Drain 2 3 0.5 1 SCH1305 P.G 50 S SANYO : SCH6 ID -- VGS --0.6 --1.0 5C --25 C C --1.5V --0.5 Ta= 7 Drain Current, ID -- A V --1.8 --0.9 --1.5 --0.3 25 VGS= --1.0V 0 0 0 --0.1 --0.2 --0.3 --0.4 Drain-to-Source Voltage, VDS -- V 0 --0.5 --0.5 --1.0 --1.5 --2.0 --2.5 Gate-to-Source Voltage, VGS -- V IT07144 RDS(on) -- VGS 800 VDS= --6V C .5 --4 Drain Current, ID -- A --1.2 75 Ta= --25 V V V .5 -3.0 2.5V -- --3 C C --2.0 25 ID -- VDS --1.5 --3.0 IT04354 RDS(on) -- Ta 800 Static Drain-to-Source On-State Resistance, RDS(on) -- m Static Drain-to-Source On-State Resistance, RDS(on) -- m Ta=25C 700 600 --0.8A 500 ID= --0.4A 400 300 200 100 0 0 --1 --2 --3 --4 --5 --6 Gate-to-Source Voltage, VGS -- V --7 --8 IT07142 700 600 8V = --1. , VGS A 1 . 0 V I D= -= --2.5 A, V GS .4 0 -I D= = --4.5V A, V GS I D= --0.8 500 400 300 200 100 0 --60 --40 --20 0 20 40 60 80 100 Ambient Temperature, Ta -- C 120 140 160 IT07143 No.7759-2/4 SCH1305 yfs -- ID 3 VGS=0 3 2 C 5 1.0 -2 =C Ta 75 7 5 3 2 2 --1.0 7 5 3 25C --25C 5C Ta=7 5C 2 2 0.1 --0.01 2 3 5 7 --0.1 2 3 5 7 --1.0 2 Drain Current, ID -- A --0.1 --0.4 3 --0.8 --1.0 --1.2 Diode Forward Voltage, VSD -- V --1.4 IT04358 Ciss, Coss, Crss -- VDS 5 VDD= --6V VGS= --4.5V 2 --0.6 IT04357 SW Time -- ID 3 f=1MHz 3 100 2 7 Ciss, Coss, Crss -- pF Switching Time, SW Time -- ns IF -- VSD 5 VDS= --6V Forward Current, IF -- A Forward Transfer Admittance, yfs -- S 5 tr 5 td(off) tf 3 2 td(on) 10 Ciss 100 7 7 5 5 Coss 3 Crss 2 3 10 2 --0.1 2 3 5 7 2 --1.0 Drain Current, ID -- A --10 7 5 Drain Current, ID -- A --2.5 --2.0 --1.5 --0.5 3 2 1.0 1.5 2.0 2.5 Total Gate Charge, Qg -- nC 3.0 IT04361 PD -- Ta 0.8 --10 --12 IT04360 ASO 10s 10 0 s ID= --1.5A DC 3 2 --1.0 0.5 --8 IDP= --6A --1.0 7 5 --0.1 7 5 0 --6 1 10 0ms 0m s op er ati on s --3.0 --4 1m 3 2 --3.5 0 --2 Drain-to-Source Voltage, VDS -- V VDS= --6V ID= --1.5A --4.0 Allowable Power Dissipation, PD -- W 0 IT04359 VGS -- Qg --4.5 Gate-to-Source Voltage, VGS -- V 3 Operation in this area is limited by RDS(on). Ta=25C Single pulse Mounted on a ceramic board (900mm20.8mm) --0.01 --0.01 2 3 5 7 --0.1 2 3 5 7 --1.0 2 3 5 7 --10 Drain-to-Source Voltage, VDS -- V 2 3 IT07145 0.7 M ou nt 0.6 ed on ac er am ic 0.4 bo ar d (9 00 m m2 0. 0.2 8m m ) 0 0 20 40 60 80 100 120 Ambient Temperature, Ta -- C 140 160 IT07146 No.7759-3/4 SCH1305 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of May, 2004. Specifications and information herein are subject to change without notice. PS No.7759-4/4