ATV12H037F1 Product data sheet Characteristics Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications variable speed drive ATV12 - 0.37kW - 0.55hp 100..120V - 1ph - with heat sink Main Range of product Altivar 12 Product or component type Variable speed drive Product destination Asynchronous motors Product specific application Simple machine Assembly style With heat sink Component name ATV12 Quantity per set Set of 1 EMC filter Without EMC filter Built-in fan Without Network number of phases 1 phase [Us] rated supply voltage 100...120 V - 15...10 % Motor power kW 0.37kW Motor power hp 0.55hp Communication port protocol Modbus Line current 11.4A at 100 V 9.3A at 120 V Speed range 1...20 Transient overtorque 150...170% of nominal motor torque depending on drive rating and type of motor Asynchronous motor control profile Voltage/frequency ratio (V/f) Quadratic voltage/frequency ratio Sensorless flux vector control IP degree of protection IP20 without blanking plate on upper part Noise level 0dB Complementary Supply frequency 50/60 Hz +/- 5 % Connector type 1 RJ45 (on front face) for Modbus Mar 16, 2021 1 Physical interface 2-wire RS 485 for Modbus Transmission frame RTU for Modbus Transmission rate 4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s Number of addresses 1...247 for Modbus Communication service Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) Prospective line Isc 1kA Continuous output current 2.4A at 4 kHz Maximum transient current 3.6A for 60 s Speed drive output frequency 0.5...400Hz Nominal switching frequency 4 kHz Switching frequency 2...16 kHz adjustable 4...16 kHz with derating factor Braking torque Up to 70 % of nominal motor torque without braking resistor Motor slip compensation Preset in factory Adjustable Output voltage 200...240 V 3 phases Electrical connection Terminal, clamping capacity: 3.5 mm, AWG 12 (L1, L2, L3, U, V, W, PA, PC) Tightening torque 0.8N.m Insulation Electrical between power and control Supply Internal supply for reference potentiometer: 5 V DC (4.75...5.25V), <10mA, protection type: overload and short-circuit protection Internal supply for logic inputs: 24 V DC (20.4...28.8V), <100mA, protection type: overload and short-circuit protection Analogue input number 1 Analogue input type Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm Discrete input number 4 Discrete input type Programmable LI1...LI4 24 V 18...30 V Discrete input logic Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1) Sampling duration 20ms, tolerance +/- 1 ms for logic input 10ms for analogue input Linearity error +/- 0.3 % of maximum value for analogue input Analogue output number 1 Analogue output type AO1 software-configurable voltage: 0...10 V, impedance: 470Ohm, resolution 8 bits AO1 software-configurable current: 0...20 mA, impedance: 800Ohm, resolution 8 bits Discrete output number 2 Discrete output type Logic output LO+, LOProtected relay output R1A, R1B, R1C 1 C/O Minimum switching current 5mA at 24 V DC for logic relay Maximum switching current 2A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay Acceleration and deceleration ramps S U Linear from 0 to 999.9 s Braking to standstill By DC injection, <30s Protection type Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases 2 Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of It Frequency resolution Analog input: converter A/D, 10 bits Display unit: 0.1 Hz Time constant 20ms +/- 1 ms for reference change Marking CE Operating position Vertical +/- 10 degree Height 143mm Width 72mm Depth 121.2mm Net weight 0.8kg Specific application Commercial equipment Variable speed drive application selection Commercial equipment Mixer Commercial equipment Other application Textile Ironing Motor starter type Variable speed drive Environment Electromagnetic compatibility Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2 Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3 Surge immunity test level 3 conforming to EN/IEC 61000-4-5 Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 Electromagnetic emission Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cable Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <5m Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20m Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20m Product certifications UL C-Tick GOST NOM CSA Vibration resistance 1 gn (f = 13...200Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f = 3...13Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/ IEC 60068-2-6 Shock resistance 15 gn conforming to EN/IEC 60068-2-27 for 11ms Relative humidity 5...95% without condensation conforming to IEC 60068-2-3 5...95% without dripping water conforming to IEC 60068-2-3 Ambient air temperature for storage -25...70C Ambient air temperature for operation -10...40C protective cover from the top of the drive removed 40...60C with current derating 2.2 % per C Operating altitude > 1000...2000 m with current derating 1 % per 100 m <= 1000 m without derating Packing Units Unit Type of Package 1 PCE Number of Units in Package 1 1 Package 1 Weight 1.031kg Package 1 Height 10.6cm Package 1 width 18.6cm Package 1 Length 18.6cm Unit Type of Package 2 P06 Number of Units in Package 2 45 Package 2 Weight 59.4kg Package 2 Height 80cm 3 Package 2 width 80cm Package 2 Length 60cm Offer Sustainability Sustainable offer status Green Premium product REACh Regulation REACh Declaration EU RoHS Directive Pro-active compliance (Product out of EU RoHS legal scope) EU RoHS Declaration Mercury free Yes RoHS exemption information Yes China RoHS Regulation China RoHS declaration Environmental Disclosure Product Environmental Profile Circularity Profile End of Life Information WEEE The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins Contractual warranty Warranty 4 18 months