Product data sheet
Characteristics
ATV12H037F1
variable speed drive ATV12 - 0.37kW - 0.55hp -
100..120V - 1ph - with heat sink
Main
Range of product Altivar 12
Product or component type Variable speed drive
Product destination Asynchronous motors
Product specific application Simple machine
Assembly style With heat sink
Component name ATV12
Quantity per set Set of 1
EMC filter Without EMC filter
Built-in fan Without
Network number of phases 1 phase
[Us] rated supply voltage 100...120 V - 15...10 %
Motor power kW 0.37kW
Motor power hp 0.55hp
Communication port protocol Modbus
Line current 11.4A at 100 V
9.3A at 120 V
Speed range 1…20
Transient overtorque 150…170% of nominal motor torque depending on drive rating and type of motor
Asynchronous motor control profile Voltage/frequency ratio (V/f)
Quadratic voltage/frequency ratio
Sensorless flux vector control
IP degree of protection IP20 without blanking plate on upper part
Noise level 0dB
Complementary
Supply frequency 50/60 Hz +/- 5 %
Connector type 1 RJ45 (on front face) for Modbus
Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications
Mar 16, 2021
1
Physical interface 2-wire RS 485 for Modbus
Transmission frame RTU for Modbus
Transmission rate 4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
Number of addresses 1…247 for Modbus
Communication service Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
Prospective line Isc 1kA
Continuous output current 2.4A at 4 kHz
Maximum transient current 3.6A for 60 s
Speed drive output frequency 0.5…400Hz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
4...16 kHz with derating factor
Braking torque Up to 70 % of nominal motor torque without braking resistor
Motor slip compensation Preset in factory
Adjustable
Output voltage 200...240 V 3 phases
Electrical connection Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC)
Tightening torque 0.8N.m
Insulation Electrical between power and control
Supply Internal supply for reference potentiometer: 5 V DC (4.75…5.25V), <10mA, protection type:
overload and short-circuit protection
Internal supply for logic inputs: 24 V DC (20.4…28.8V), <100mA, protection type: overload and
short-circuit protection
Analogue input number 1
Analogue input type Configurable current AI1 0...20 mA 250 Ohm
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm
Discrete input number 4
Discrete input type Programmable LI1...LI4 24 V 18...30 V
Discrete input logic Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)
Sampling duration 20ms, tolerance +/- 1 ms for logic input
10ms for analogue input
Linearity error +/- 0.3 % of maximum value for analogue input
Analogue output number 1
Analogue output type AO1 software-configurable voltage: 0...10 V, impedance: 470Ohm, resolution 8 bits
AO1 software-configurable current: 0...20 mA, impedance: 800Ohm, resolution 8 bits
Discrete output number 2
Discrete output type Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
Minimum switching current 5mA at 24 V DC for logic relay
Maximum switching current 2A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Acceleration and deceleration ramps S
U
Linear from 0 to 999.9 s
Braking to standstill By DC injection, <30s
Protection type Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
2
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
Frequency resolution Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz
Time constant 20ms +/- 1 ms for reference change
Marking CE
Operating position Vertical +/- 10 degree
Height 143mm
Width 72mm
Depth 121.2mm
Net weight 0.8kg
Specific application Commercial equipment
Variable speed drive application
selection
Commercial equipment Mixer
Commercial equipment Other application
Textile Ironing
Motor starter type Variable speed drive
Environment
Electromagnetic compatibility Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3
Surge immunity test level 3 conforming to EN/IEC 61000-4-5
Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
Electromagnetic emission Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded
motor cable
Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC
61800-3 4...12 kHz shielded motor cable <5m
Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC
61800-3 4...12 kHz shielded motor cable <20m
Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC
61800-3 4...12 kHz shielded motor cable <20m
Product certifications UL
C-Tick
GOST
NOM
CSA
Vibration resistance 1 gn (f = 13…200Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/
IEC 60068-2-6
Shock resistance 15 gn conforming to EN/IEC 60068-2-27 for 11ms
Relative humidity 5…95% without condensation conforming to IEC 60068-2-3
5…95% without dripping water conforming to IEC 60068-2-3
Ambient air temperature for storage -25…70°C
Ambient air temperature for operation -10…40°C protective cover from the top of the drive removed
40…60°C with current derating 2.2 % per °C
Operating altitude > 1000...2000 m with current derating 1 % per 100 m
<= 1000 m without derating
Packing Units
Unit Type of Package 1 PCE
Number of Units in Package 1 1
Package 1 Weight 1.031kg
Package 1 Height 10.6cm
Package 1 width 18.6cm
Package 1 Length 18.6cm
Unit Type of Package 2 P06
Number of Units in Package 2 45
Package 2 Weight 59.4kg
Package 2 Height 80cm
3
Package 2 width 80cm
Package 2 Length 60cm
Offer Sustainability
Sustainable offer status Green Premium product
REACh Regulation REACh Declaration
EU RoHS Directive Pro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration
Mercury free Yes
RoHS exemption information Yes
China RoHS Regulation China RoHS declaration
Environmental Disclosure Product Environmental Profile
Circularity Profile End of Life Information
WEEE The product must be disposed on European Union markets following specific waste collection and
never end up in rubbish bins
Contractual warranty
Warranty 18 months
4