L6935 High performance 3 A ULDO linear regulator Features Up to 5 V input voltage range 60 m max RDS(on) 35 A shut-down current 3 A maximum output current Split bias and power supplies Adjustable output voltage: 0.5 V to 3.0 V Excellent load and line regulation: 1 % accuracy (over temperature) Description MLCC supported Programmable soft-start Short-circuit protection 3.5 A overcurrent protection Thermal shut-down L6935 is an ultra low drop output linear regulator operating up to 5 V input and is able to support output current up to 3 A. Designed with an internal low-RDS(on) N-channel MOSFET, it can be used for on-board DC-DC conversions saving in real estate, list of components and power dissipation. VFQFPN20 4 x 4 x 1.0 mm package Applications Motherboard Mobile PC Hand-held instruments PCMCIA cards Processors I/O Chipset and RAM supply Table 1. Bias input and power input are split to allow linear conversion from buses lower than 1.2 V minimizing power losses. L6935 provides the application with an adjustable voltage from 0.5 V to 3.0 V with a voltage regulation accuracy of 1 %. soft-start is available to program the output voltage rise-time according to the external capacitor connected. Enable and Power Good functions make L6935 suitable for complex systems and programmable start-up sequencing. The current limit at 3 A protects the system during a short circuit. The current is sensed in the power DMOS in order to limit the power dissipation. Thermal shut down limits the internal temperature at 150 C with a hysteresis of 20 C. Device summary Order codes L6935 L6935TR May 2008 VFQFPN20 (4.0 x 4.0 x 1.0 mm) Package Packing Tube VFQFPN20 Tape and reel Rev 1 1/20 www.st.com 20 Contents L6935 Contents 1 2 Typical application circuit and block diagram . . . . . . . . . . . . . . . . . . . . 3 1.1 Application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pins description and connection diagrams . . . . . . . . . . . . . . . . . . . . . . 5 2.1 3 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 Typical performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6 5.1 Soft-start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.2 Power Good . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.3 VIN vs VBIAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.4 Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.4.1 Over-current protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.4.2 Thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.1 6.2 Components selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.1.1 Input capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.1.2 Output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 VIN, VBIAS and sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7 Demonstration board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8 VFQFPN20 mechanical data and package dimensions . . . . . . . . . . . . 18 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 Typical application circuit and block diagram L6935 1 Typical application circuit and block diagram 1.1 Application circuit Figure 1. Typical application circuit - VIN = VBIAS VIN EN VOUT = 0.5V to 3.0V VBIAS VIN VOUT L6935 CIN EN SS GND PAD R1 COUT ADJ PGOOD R2 CSS PGOOD L6935 Reference Schematic Figure 2. Typical application circuit - VIN VBIAS VBIAS VIN = 0.75V to VBIAS VIN EN EN VBIAS L6935 CIN SS GND PAD VOUT > 0.5V (*) VOUT R1 COUT ADJ PGOOD R2 CSS PGOOD L6935 Reference Schematic (*) Vin may decrease until the minimum drop is reached. Conversely, Vout can rise untile the minimum drop is reached. 3/20 Typical application circuit and block diagram 1.2 L6935 Block diagram Figure 3. Block diagram VIN CHARGE PUMP VBIAS CURRENT LIMIT VREF REFERENCE 0.500V SS + ERROR AMPLIFIER DRIVER VOUT ADJ EN ENABLE THERMAL SENSOR PGOOD + 0.9 VREF GND 4/20 - Pins description and connection diagrams 2 L6935 Pins description and connection diagrams Figure 4. Pins connection (top view) VBIAS EN VIN VIN VIN 10 9 11 8 7 6 12 13 5 4 L6935 14 3 2 15 1 16 17 18 19 20 PGOOD N.C. N.C. GND N.C. VOUT VOUT VOUT ADJ SS N.C. N.C. N.C. N.C. N.C. 2.1 Pin descriptions Table 2. Pin # Name 1 N.C. Not internally connected. 2 GND Ground connection. Connect to PCB ground plane. 3, 4 N.C. Not internally connected. 5 PGOOD Power Good output flag: the pin is open drain and it is forced low if the output voltage is lower than 90 % of the programmed voltage. If not used, it can be left floating. VBIAS Input bias supply. This pin supplies the internal logic to drive the power N-channel MOSFET that realize the voltage conversion. Connect directly to VIN or to a different supply ranging from VIN to 5 V. The voltage connected to this pin MUST always be higher or equal that VIN. 7 EN Enables the device if a voltage higher than 1 V is applied. When pulled low, the device is in low-power consumption: everything inside the controller is kept OFF. See Section 6.2 for details about EN signal and power sequencing. 8 to 10 VIN Power supply voltage. This pin is connected to the drain of the internal N-channel MOSFET. Filter to GND with capacitor larger than the one used for VOUT. 11 to15 N.C. Not internally connected. 16 to 18 VOUT 6 5/20 Pins descriptions Function Regulated output voltage. This pin is connected to the source of the internal N-mos. MLCC capacitor are supported. Filter to GND with capacitor smaller than the one used for VIN. Pins description and connection diagrams Table 2. 6/20 L6935 Pins descriptions (continued) Pin # Name Function 19 ADJ Feedback for the IC regulation. Connecting this pin through a voltage divider to VOUT, it is possible to program the output voltage between 0.5 V and 3.0 V. 20 SS Soft-start pin. The soft-start time is programmed connecting an external capacitor CSS from this pin to GND. In steady state regulation, the voltage at this pin is 3.3 V. PAD GND Ground connection. Connect to PCB GND Plane with enough VIAs to improve thermal conductivity. Electrical specifications L6935 3 Electrical specifications 3.1 Absolute maximum ratings Table 3. Absolute maximum ratings Symbol Parameter Unit VIN to GND 5.5 V VBIAS, EN, PGOOD to GND 6 V SS, VOUT to GND -0.3 to 3.3 V ADJ to GND -0.3 to 1 V 1000 V Maximum withstanding voltage range test condition: CDF-AEC-Q100-002 "human body model" acceptance criteria: "normal performance" 3.2 Value Thermal data Table 4. Symbol Thermal data Parameter Value Unit RthJA Thermal resistance junction to ambient(1) 55 C/W TMAX Maximum junction temperature 150 C TSTG Storage temperature range -50 to 150 C TJ Junction temperature range -25 to 150 C 1. Measured with the component mounted on demonstration board in free air (22 x 28.5 mm - 2 layer 70 m copper). 7/20 Electrical specifications L6935 3.3 Electrical characteristics Table 5. Electrical characteristics (VIN = 5 V, VBIAS = 5 V; TA = 25 C unless otherwise specified). Symbol Parameter Test conditions Min Typ Max Unit Recommended operating conditions VIN VBIAS IIN Operating supply voltage VIN = VBIAS VBIAS < 5 V 5.0 VBIAS V UVLO VBIAS rising 1.275 V Quiescent current Iout = 0 A 3 mA Shut-down current VIN = VBIAS = 3.3 V VIN = VBIAS = 5.0 V 25 40 A 0.504 V 2.5 2.5 mV 7 mV 2.3 Voltage regulation VOUT Output voltage Io = 0.1 A; VIN = 3.3 V; ADJ = OUT Line regulation Vin = 3.30 V +/- 10 %; Io = 10 mA Vin = 4.50 V +/- 10 %; Io = 10 mA Load regulation Vin = 3.3 V; Io = 100 mA to 3 A Ripple rejection (1) F = 100...120 Hz; Io = 10 mA Vin = 3 V; Vin = 2 Vpp; Vout = 1 V 45 Drain-to-source resistance Io = 3 A 30 60 m 3.50 3.85 A 85 % ADJ RDS(on) 0.496 0.500 dB Enable, SS and protections IOCP PGOOD Current limiting Vo = 1.8 V 3.15 Power Good threshold VADJ falling, wrt Ref. Hysteresis 77 10 % Voltage low I = -1 mA 0.4 V EN Enable threshold EN rising 1.05 V SS Soft start current Vss = 0 V Temperature rising OT Thermal shut-down Hysteresis (1) 1. Parameter guaranteed by design, not tested in production 8/20 (1) 1.0 A 150 C 20 C Typical performances 4 L6935 Typical performances Figure 5. Output voltage and OC threshold vs junction temperature 1.0 4.0 0.8 3.8 0.4 OC Threshold [A] Output Voltage [%] 0.6 0.2 0.0 -0.2 -0.4 -0.6 3.6 3.4 3.2 -0.8 -1.0 3.0 -40 -20 Figure 6. 0 20 40 60 80 Temperature [C] 100 120 140 -40 -20 0 20 40 60 80 Temperature [C] 100 120 140 Quiescent and shutdown current vs junction temperature 4.0 40 5 VIN Shutdown Current [uA Quiescent Current [mA] 35 3.8 3.6 3.4 3.2 30 25 20 15 3 VIN 10 5 3.0 -40 Figure 7. -20 0 20 40 60 80 Temperature [C] 100 120 0 140 -40 -20 0 100 120 140 0.2% VBIAS = 1.4V, VOUT = 2V VBIAS = VIN, VOUT = 0.5V 0.1% Line Regulation [%] Line Regulation [%] 40 60 80 Temperature [C] Line regulation 0.2% 0.0% -0.1% 0.1% 0.0% -0.1% -0.2% -0.2% 1.0 9/20 20 1.5 2.0 2.5 3.0 VIN [V] 3.5 4.0 4.5 5.0 2.0 2.5 3.0 3.5 VIN [V] 4.0 4.5 5.0 Typical performances Figure 8. L6935 Load regulation 0.3% 0.3% VBIAS = VIN = 1.4V, VOUT = 0.5V VBIAS = 1.4V, VIN = 2.6V, VOUT = 2V 0.2% Load Regulation [%] Load Regulation [%] 0.2% 0.1% 0.0% -0.1% 0.0% -0.1% -0.2% -0.2% -0.3% -0.3% 0.0 0.5 1.0 1.5 Output Current [A] 10/20 0.1% 2.0 2.5 0.0 0.5 1.0 1.5 Output Current [A] 2.0 2.5 Device description L6935 5 Device description 5.1 Soft-start L6935 implements a soft-start feature to smoothly charge the output filter avoiding high inrush currents to be required to the input power supply. The soft-start process begins as soon as VBIAS reaches UVLO and ENABLE is asserted. A constant current ISS = 1.0 A is sourced through the SS pin: connecting an external capacitor (CSS) to this pin a voltage ramp is implemented; the voltage ramp internally clamps the E.A. reference, resulting in a controlled slope for the output voltage. As the voltage on CSS reaches the VREF value the internal clamp is released. In this way, the soft-start process lasts for: V REF 5 T SS = C SS -------------- = 5 10 C SS [ F ] I SS where CSS is the external capacitor [F] and TSS is the soft-start time [sec.]. If the device is disabled (ENABLE low) and the VBIAS is still present, the SS pin is clamped to GND for a fixed time of about 50 s. in order to discharge the residual charge present on CSS: in this way, the device will be ready for a new SS process as ENABLE is asserted again. Figure 9 describes a typical soft-start process. Figure 9. Soft start process diagram (left) and measured (right) Vbias >1.1V ENABLE >0.7V ADJ 0.5V Vout Programmed Vout Programmed Tss ~50sec 11/20 Device description 5.2 L6935 Power Good L6935 presents a PGOOD flag, an open drain output that is grounded during all the soft start procedure, and is left free when VOUT reaches 90 % of the programmed value. An hysteresis of 10 % is also provided in order to avoid false triggering due to the noise generated by the application. Figure 10 shows the PGOOD commutations. Figure 10. Power good window 5.3 VIN vs VBIAS L6935 provides the flexibility to supply the internal logic (VBIAS) with a supply different than the power input (VIN). The aim of this feature is to provide low-drop regulation still having the supply voltage to correctly drive the internal power mosfet so optimizing the conversion. VIN drives only the drain of the power DMOS and it can be kept as low as possible (VIN > VOUT + VDROPmin), while VBIAS drives the control section. VBIAS must be typically higher than VIN. 5.4 Protections L6935 is equipped with a set of protections in order to protect both the load and the device from electrical overstress. Each protection does not latch the device, that returns to work properly as the perturbation disappear. 5.4.1 Over-current protection An over current protection is provided: if the current that flows through the power DMOS is greater than 3.5 A, the device adjust the power DMOS driving voltage in order to keep constant the delivered current (IOUT). Anyhow the output may drop also causing the PGOOD to be set low. Figure 11 show the way the OCP intervention: as the threshold value is reached by IOUT, the device forces a lower output current (~3.5 A). 12/20 Device description L6935 Figure 11. Over-current protection 5.4.2 Thermal protection The device constantly monitors its internal temperature. As the silicon reaches a 150 C, the control circuit turns off the power DMOS, and stays off until a safe temperature of 150 - 20 = 130 C. Figure 12 shows how the over-temperature protection intervention. Figure 12. Over-temperature protection 13/20 Application information 6 L6935 Application information L6935 is the best choice in smart linear regulator applications, due to its own small size, high power delivered and high regulation accuracy. Furthermore thermal shut-down and OCP guarantee the highest reliability for each application. VIN can be separated by VBIAS: in this way the device can regulate the output voltage even if VIN < VBIAS, resulting in a better performance. In fact, the power dissipated decreases as VIN get lower, according to the relationship PDISS = (VIN - VOUT) x IOUT. 6.1 Components selection 6.1.1 Input capacitor The choice of the input capacitor value depends on the several factor such as load transient requirements, input source (battery or DC/DC converter) and its distance from the input capacitor. Generally speaking, a capacitor with the lowest ESR possible should be chosen: a value within the range [10 F; 100 F] can be sufficient in many cases. 6.1.2 Output capacitor The choice of the output capacitor value basically depends on the load transient requirement. Output capacitor must be sized according to the dynamic requests of the load. A too small capacitor may exhibit huge voltage drop after a load transient is applied: a value greater than 10 F should be used. In order to guarantee a good reliability, at least X5R type should be used as I/O capacitors. Different kinds of input/output capacitors can be used: Table 6. shows a few tested examples. Table 6. Input/output capacitor selection guide Manufacturer Type Murata - GRM31CR61ExxxK(1) MLCC, SMD1206, X5R 10...100 F 6.3 - 25 V Panasonic - ECJ3YB1AxxxM MLCC, SMD1206, X5R 10...100 F 10 - 25 V Panasonic - EEFFD0HxxxR SPCap - SMD7343 28 m ESR 10...100 F 4-8V Sanyo - 8TPE100MPC2 POSCAP, SMD6032 25 m ESR 10...100 F 6.3 - 25 V MLCC, SMD1210, X5R 10...100 F 6.3 V TDK - C3216X5R0JxxxMT I/O cap. value Rated voltage 1. xxx in the part numbers stands for 106 (10 F), 226 (22 F)... 105 (100 F) 14/20 Application information 6.2 L6935 VIN, VBIAS and sequencing Different configurations for VIN and VBIAS are possibleand the power sequencing must consider the different timings in which the power suppliesbecomes available. In order to properly drive the device internal logic, it is reccomendedto control the sequence between EN signal and the VIN / VBIAS application: the device need to result being disabled when VBIAS crosses the UVLO threshols. Furthermore, in case of VIN <> VBIAS, the EN signal needs to be driven by the last-coming between the two supplies. It is reccomended to drive the EN pin with a resistor divider connected as reported into Figure 13 and Figure 14. Figure 13. Recommended circuit for VBIAS = VIN VIN L6935 REH CIN VOUT = 0.5V to 3.0V VBIAS VIN EN SS VOUT R1 RPG COUT PGOOD GND PAD ADJ PGOOD EN (OpenDrain Toggle **) REL R2 CSS ** Drive EN with external Open-Drain Signal. Figure 14. Reccomended circuit for VBIAS VIN VBIAS VIN (< VBIAS) REH* CIN L6935 EN SS VOUT = 0.5V to 3.0V VBIAS VIN VOUT R1 RPG COUT PGOOD GND PAD ADJ PGOOD EN (OpenDrain Toggle **) REL CSS R2 * EN Divider (REH) needs to be connected to the Last-Coming rail between VCC and VIN. ** Drive EN with external Open-Drain Signal. 15/20 Demonstration board description 7 L6935 Demonstration board description Figure 15 and Figure 16 show the schematic and the layout of the demonstration board designed for L6935. VIN and VBIAS may be different and, in this case, R4 must not be mounted. C3 defines the Soft-Start timer, according to the relationship described in the Section 5.1. The value of the output divider R1 / R2 have to be designed in order to program the desired VOUT value, according to the following equation: R V OUT = 0.5 1 + ------1- R 2 Figure 15. Demonstration board schematic VBIAS PGOOD R4 C2 R5 6 VIN 8, 9, 10 VIN EN 7 EN C4 VBIAS 20 GND PAD R3 C6 Figure 16. Demonstration board layout R1 ADJ 19 C5 2 C3 16/20 VOUT L6935 PGOOD 5 SS C1 16,17,18 VOUT R2 ADJ GND Demonstration board description L6935 Different values for R1 are available in order to program the value of VOUT (R2 = 10 k) VOUT = 0.50 VDC @ R1 = 0 VOUT = 0.75 VDC @ R1 = 5 k VOUT = 1.00 VDC @ R1 = 10 k VOUT = 1.25 VDC @ R1 = 15 k VOUT = 1.50 VDC @ R1 = 20 k VOUT = 3.00 VDC @ R1 = 50 k Table 7. L6935 demonstration board bill of material Reference C1, C2, c3 Chip capacitor 100 nF - 6.3 V - X5R C4 Murata chip capacitor (GRM31CR60J226K) 1206, X5R, 6.3-25V, 22 F C5 Murata chip capacitor (GRM31CR61E106K) 1206, X5R, 6.3-25V, 10 F C6 Not mounted R1 Chip resistor 15 k +/-0.1% - 1/16 W R2 Chip resistor 10 k +/-0.1% - 1/16 W R3, R5 R4 17/20 Description Chip resistor 10 k +/-5% - 1/16 W Chip resistor 0 VFQFPN20 mechanical data and package dimensions 8 L6935 VFQFPN20 mechanical data and package dimensions In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 17. VFQFPN20 mechanical data and package dimensions DIMENSIONS REF. A mm mils MIN. TYP. MAX. MIN. TYP. 0.80 MAX. 0.90 1.00 31.496 35.433 39.370 A1 0.02 0.05 0.787 A2 0.65 1.00 25.591 39.370 A3 0.25 1.969 9.843 9.055 PACKAGE AND PACKING INFORMATION b 0.18 0.23 0.30 7.087 D 3.85 4.00 4.15 151.57 157.48 163.39 D2 2.70 2.80 2.90 106.30 110.24 114.17 Very Fine Quad Flat Package No lead 11.811 Weight: not available E 3.85 4.00 4.15 151.57 157.48 163.39 E2 2.70 2.80 2.90 106.30 110.24 114.17 e 0.45 0.50 0.55 17.717 19.685 21.654 L 0.3 0.4 0.5 11.811 15.748 19.685 ddd 18/20 0.08 3.150 VFQFPN20 (4x4x1.00mm) Revision history 9 L6935 Revision history Table 8. 19/20 Document revision history Date Revision 20-May-2008 1 Changes Initial release L6935 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20