JNPS-O813B
~! .P- 1+ ~ ~
= 1:11:1 I-L '1;]< "8
Product Specification
APRV.~~~~ ~ ~7 .2Po
CHKD. 75'.;{v'0.,?p/ ~7 2-qQk
PRPD. j': ~..P c.-.c.J2- % " 1," y
SUMITOMO 3M LIMITED
ELECfRONIC SOLUTIONS DIVISION
TECHNICAL DEPARTMENT
JNPS-O813 B
§ tX / CONTENTS
~ /PAGE
~~ 1
FUNCnON
2. ~i!i-'!/j~ 1
COMPAnBLE OBJECTS 6
3. ~~ft~~ 1
RELATED SPECIFICA noN DRA WINGS 6
4. lU]imm~M 1
RELATED TEST STANDARDS 6
~m 2
APPLICA TION
5.
6. J'I1WI.f!j1t. 3
QUALITY PERFORMANCE 8
7~J'11 J::~,?~f:f:~~JjIJ** 5
PLAnNG SPEC INDICATION ON CONNECTOR 10
§1ti&*~ 5
PACKAGE & IDENTIFICATION 10
8
*~ 5
STORAGE 10
9
10 ~;i:*Jj 5
ATTENnONS ' 10
JNPS-O813 B
FUNCTION
This connector is one ofMDR board mount receptacle right angle series. And mating side has 2 rows of
female contacts with the pitch of 1.27mm and contact tails are arranged in 1.27mmxl.905mm staggered
grid. This connector can be mounted on the compatible PC board and mating with MDR plug connector
enable to have the electrical performance.
2. COMPATIBLE OBJECTS
2- COMPATIBLE CONNECTORS
3M BRAND MDR PLUG: lOlXX-XXXX XX
2-2 COMP AIBLE PC BOARDS
PCB with solder plating hole
See RELA TED SPECIFICATION DRA WINGS recommended hole pattern
PCB RETENSION
METHOD PCB RETENSION
HOLE DIA.
PRODUCT No PCB THICKNESS
3.9 mm Tail: 3.0 mm Max.
2.8 mm Tail: 1.6 mm Max.
2.3 mm Tail: 1.2 mm Max.
cp 2.8 mm
SCREW LOCK
$3.2mm
GROUND LOCK TYPEl <I> 2.6 mm 1.6mm
GROUND LOCK TYPE2 4> 2.8 mm 0.6 mm or 1.2 mm
cp 2.8 mm (recommended)
or cp 2.6 mm 0.6 mm Min.
1.6mmMax
GROUND LOCK TYPE3
2-3 COMPATIBLE PANELS
Thickness of panels: 2.0 mm Max. (Including with the thickness of washers)
See RELATED SPECIFICA naN DRA WINGS for recommended panel cut-out.
3RELATED SPECIFICATION DRA WINGS
See the drawings described in JNPD-O813.
4. RELA TED TEST STANDARDS
MIL-Sm-202
JEIDA-38-1984
ns C 0050
JNTM-0039, JNTM-0040
* JNTM: Test Method Standard of Sumitomo 3M for Electronic and Electrical Component Parts
6
JNPS-O813 B
5. APPLICA TION
PRODUCT NUMBER INFORMATION
1! PX
PLA TING THICKNESS SUFFIX
PL : under Nickel Plating
CONTACT AREA / Gold Plating 0.2 ~m Min.
TAIL AREA / Gold Flash Plating
with Lubricant Treatment
PE : under Nickel Plating
CONTACT AREA / Gold Plating 0.5 ~m Min.
TAIL AREA / Gold Flash Plating
PC: under Nickel Plating
CONT ACT AREA / Gold Plating 0.76 ~m Min.
T AIL AREA / Gold Flash Plating
SOLDER TAIL
2 : 3.9mm
3 : 2.8mm
4: 2.3mm
RETENTION FEA TORE
0 : Lock Stand (M2.6mm) for Panel and Screw Lock (M2.6) for PC Board
1 : Lock Stand (M2.5mm) for Panel and Screw Lock (M2.5) for PC Board
4 : Lock Stand (No.4-40) for Panel and Screw Lock (No.4-40) for PC Board
A : Lock Stand (M2.6mm) for Panel and Ground Lock Type 1 for PC Board
B : Lock Stand (M2.5mm) for Panel and Ground Lock Type 1 for PC Board
D : Lock Stand (M2.6mm) for Panel and Ground Lock Type 2 for PC Board
E : Lock Stand (No.4-40) for Panel and Ground Lock Type I for PC Board
F : Lock Stand (M2.6mm) for Panel and Ground Lock Type 3 for PC Board
G : Lock Stand (M2.5mm) for Panel and Ground Lock Type 3 for PC Board
H : Lock Stand (No.4-40) for Panel and Ground Lock Type 3 for PC Board
TYPE
2 : Standard Body
PIN CONFIGURAnONS
5 : Board Mount Right Angle Type
CONTACT QUANTITY
XX : XX Pos. (Exception: 100 pos. is shown II AO"
PRODUCT SERIES NAME
102: MDR Receptacle
JNPS-O813 B
6. QUALITY PERFORMANCE
6-1 RATING
6-2 PHYSICAL SPECIFICATIONS * The value in ( ) is reference.
8
JNPS-O813 B
6-3 ELECTRICAL SPECIFICATIONS
TEST
DESCRIPnON
RELA TED
STANDARD
REQUIREMENT TEST CONDITION
No appearance of arcing
and break down.
Leak current: lmA Max.
DIELECTRIC
WITHSTANDING
VOLTAGE
Impressed voltage is AC SOOV rms.
between adjacent two contacts for one
minute.
SOOMQ Mill.
INSULA TION
RESIDENSE Impressed voltage is DC SOOV between
adjacent two contacts for one minute.
Less than l~s
DISCONnNUITY -Vibration test
* as the part of3M SEQUENCE-II
-Mechanical sock test See Table
Initial /
for each plating spec
3Sm.O. Max.
Contact resistance is measured
at Short Circuit.
Current: 1.5mA
Open Circuit Voltage: 20mV
by 4 terminal method.
* Measurement values include
the resistance of contact pins
as conductive material.
Change of contact
resistance after
evaluation tests/
for each plating spec
::!: 25m.O. Max.
(I) PL Plating
3M SEQUENCE -1/
mating (30 cycles) 7 moisture
7 salt spray
3M SEQUENCE -II /
thermal shock 7 humidity
7 vibration
3M SEQUENCE -III /
thermal life
H2S GAS SEQUENCE /
mating (30 cycles)7 H2S gas
DURABILITY /
300 cycles
MECHANICAL SHOCK /
CONTACT
RESISTANCE See Table
(2) PE Plating and PC Plating
3M SEQUENCE -1/
mating (50 cycles) 7 moisture
7 salt spray
3M SEQUENCE -II /
thermal shock 7 humidity
7 vibration
3M SEQUENCE -III /
thermal life
H2S GAS SEQUENCE /
mating (50 cycles)7 H2S gas
DURABILITY /
500 cycles
.NOTE: See Table I.
for environmental tests.
9
JNPS-O813 B
Table I: ENVIROMENTAL TEST
7. PLA TING SPEC INDICA TION ON CONNECTOR
The first letter, in stamped 3 letters on the connector body for lot numbering, identified the following
plating specs.
R xx: PL plating
.2: XX: PE plating
y XX: PC plating
* xx: two alphabet letters
8. PACKAGE & IDENTIFICATION
These products are packed with plastic tray and carton box for transit.
Carton box is identified by part number, quantity, maker name and lot number
9STORAGE
This products shall be stored in a room, ambient temperature 5 -35°C, and ambient humidity
40- 70%.
10. ATTENTIONS
10-1 FIXING OF CONNECTOR
The connector should be fixed on panel by screws.
10
