JNPS-O813B ~! = .P1:11:1 Product 1+ I-L ~ '1;]< ~ "8 Specification APRV.~~~~ ~ ~7 CHKD. 75'.;{v'0.,?p/ ~7 PRPD. j': % ~..P SUMITOMO c.-.c.J2- 3M .2Po 2-qQk " 1," y LIMITED ELECfRONIC SOLUTIONS DIVISION TECHNICAL DEPARTMENT JNPS-O813 tX / CONTENTS ~ ~~ /PAGE 1 FUNCnON 2. ~i!i-'!/j~ 1 COMPAnBLE 3. STANDARDS 6 TION 3 PERFORMANCE 8 ~J'11 J::~,?~f:f:~~JjIJ** SPEC INDICATION 1ti&*~ PACKAGE 9 6 1 TEST J'I1WI.f!j1t. PLAnNG 8 DRA WINGS 2 QUALITY 7 noN ~m APPLICA 6. 1 SPECIFICA lU]imm~M RELATED 5. 6 ~~ft~~ RELATED 4. OBJECTS 5 ON CONNECTOR 10 5 & IDENTIFICATION *~ 10 5 STORAGE 10 ~;i:*Jj ATTENnONS 10 5 ' 10 B JNPS-O813 B FUNCTION This connector is one ofMDR board mount receptacle right angle series. And mating side has 2 rows of female contacts with the pitch of 1.27mm and contact tails are arranged in 1.27mmxl.905mm staggered grid. This connector can be mounted on the compatible PC board and mating with MDR plug connector enable to have the electrical performance. COMPATIBLE OBJECTS 2. 2- COMPATIBLE CONNECTORS 3M BRAND MDR PLUG: lOlXX-XXXX XX 2-2 COMP AIBLE PC BOARDS PCB with solder plating hole SeeRELA TED SPECIFICATION DRA WINGS recommendedhole pattern PRODUCTNo PCB RETENSION METHOD PCB RETENSION HOLE DIA. cp 2.8 mm SCREW LOCK PCB THICKNESS 3.9 mm Tail: 3.0 mm Max. 2.8 mm Tail: 1.6 mm Max. 2.3 mm Tail: 1.2 mm Max. $3.2mm GROUND LOCK TYPEl <I>2.6 mm 1.6mm GROUND LOCK TYPE2 4> 2.8 mm 0.6 mm or 1.2 mm cp 2.8 mm (recommended) GROUND LOCK TYPE3 or cp2.6 mm 0.6 mm Min. 1.6mmMax 2-3 COMPATIBLE PANELS Thickness of panels: 2.0 mm Max. (Including with the thickness of washers) SeeRELATED SPECIFICAnaN DRA WINGS for recommendedpanel cut-out. 3 RELATED SPECIFICATION DRA WINGS Seethe drawings describedin JNPD-O813. 4. RELA TED TEST STANDARDS MIL-Sm-202 JEIDA-38-1984 ns C 0050 JNTM-0039, JNTM-0040 * JNTM: Test Method Standardof Sumitomo 3M for Electronic and Electrical Component Parts 6 JNPS-O813 B APPLICA TION 5. PRODUCT NUMBER INFORMATION 1! PX PLA TING THICKNESS SUFFIX PL : under Nickel Plating CONTACT AREA / Gold Plating 0.2 ~m Min. TAIL AREA / Gold Flash Plating with Lubricant Treatment PE : under Nickel Plating CONTACT TAIL PC: SOLDER AREA / Gold Plating 0.5 ~m Min. AREA / Gold Flash Plating under Nickel Plating CONT ACT AREA / Gold Plating 0.76 ~m Min. TAIL T AIL AREA / Gold Flash Plating 2 : 3.9mm 3 : 2.8mm 4: 2.3mm RETENTION FEA TORE 0 : Lock Stand (M2.6mm) for Panel and Screw Lock (M2.6) for PC Board 1 : Lock Stand (M2.5mm) for Panel and Screw Lock (M2.5) for PC Board 4 : Lock Stand (No.4-40) for Panel and Screw Lock (No.4-40) for PC Board A : Lock Stand (M2.6mm) for Panel and Ground Lock Type 1 for PC Board B : Lock Stand (M2.5mm) for Panel and Ground Lock Type 1 for PC Board D : Lock Stand (M2.6mm) for Panel and Ground Lock Type 2 for PC Board E : Lock Stand (No.4-40) for Panel and Ground Lock Type I for PC Board F : Lock Stand (M2.6mm) G : Lock Stand (M2.5mm) H : Lock Stand (No.4-40) for Panel and Ground Lock Type 3 for PC Board for Panel and Ground Lock Type 3 for PC Board for Panel and Ground Lock Type 3 for PC Board TYPE 2 : Standard Body PIN CONFIGURAnONS 5 : Board Mount Right Angle Type CONTACT QUANTITY XX : XX Pos. (Exception: PRODUCT SERIES NAME 102: MDR Receptacle 100 pos. is shown IIAO" JNPS-O813 6. QUALITY PERFORMANCE 6-1 RATING 6-2 PHYSICAL * The SPECIFICATIONS 8 value in ( ) is reference. B JNPS-O813 6-3 ELECTRICAL SPECIFICATIONS TEST DIELECTRIC WITHSTANDING VOLTAGE INSULA TION RESIDENSE No appearanceof arcing and break down. Leak current: lmA Max. SOOMQ Mill. Less than l~s DISCONnNUITY Impressed voltage is AC SOOV rms. between adjacent two contacts for one minute. Impressedvoltage is DC SOOVbetween adjacent two contacts for one minute. -Vibration test * as the part of3M -Mechanical Initial / for each plating spec 3Sm.O. Max. RELA TED STANDARD TEST CONDITION REQUIREMENT DESCRIPnON SEQUENCE-II SeeTable sock test Contact resistanceis measured at Short Circuit. Current: 1.5mA Open Circuit Voltage: 20mV by 4 terminal method. * Measurement values include the resistanceof contact pins as conductive material. Change of contact resistance after evaluation tests/ for each plating spec ::!:25m.O. Max. (I) PL Plating 3M SEQUENCE -1/ mating (30 cycles) 7 moisture 7 salt spray 3M SEQUENCE -II / thermal shock 7 humidity 7 vibration 3M SEQUENCE thermal life CONTACT RESISTANCE -III / H2S GAS SEQUENCE / mating (30 cycles)7 DURABILITY / 300 cycles H2S gas MECHANICAL See Table SHOCK / (2) PE Plating and PC Plating 3M SEQUENCE -1/ mating (50 cycles) 7 moisture 3M SEQUENCE 7 salt spray -II / thermal shock 7 humidity 7 vibration 3M SEQUENCE thermal life -III / H2S GAS SEQUENCE / mating (50 cycles)7 DURABILITY / 500 cycles H2S gas .NOTE: 9 See Table I. for environmental tests. B JNPS-O813 Table I: ENVIROMENTAL 7. B TEST PLA TING SPEC INDICA TION ON CONNECTOR The first letter, in stamped 3 letters on the connector body for lot numbering, identified the following plating specs. R xx: PL plating .2:XX: PE plating y XX: PC plating * xx: two alphabet letters 8. PACKAGE & IDENTIFICATION These products are packed with plastic tray and carton box for transit. Carton box is identified by part number, quantity, maker name and lot number 9 STORAGE This products shall be stored in a room, ambient temperature 5 -35C, 40- 70%. 10. ATTENTIONS 10-1 FIXING OF CONNECTOR The connector should be fixed on panel by screws. 10 and ambient humidity