a4 Raychem GO%-CAO > 604- ole Overcurrent and overtemperature protection The PolySwitch circuit protector is a positive temperature coefficient (PTC) resistor that undergoes a large abrupt change in resistance when an overcurrent or high temperature heats it above a specific point. Normally just tens of milliohms, the resistance of the PolySwitch device increases by orders of magnitude when switched. This increase limits circuit current to several milliamps. Remotely resettable The device will reset when voltage in the circuit is removed, or in some cases will reset automatically when the overload * Small size Low resistance * High hold currents * Remotely resettable fuses * Latching operation Rugged, monolithic construction PolySwitch RUE R-Line PTC overcurrent protection ee ee eee aaa condition is corrected. Normal circuit operation can then be resumed. The device requires no manual resetting or replacement. Latching (noncycling) operation After switching, the PolySwitch device is latched into its high-resistance, protective State by the small, sustained self-heating current. The device will reset only after it has cooled and the fault condition has been corrected, thus avoiding continuous cycling that could cause circuit damage. Rugged, monolithic constuction Since they are made from solid-state material, PolySwitch devices have no moving parts that can be damaged. Wide variety of applications Possible applications for PolySwitch devices include: * audio speakers * batteries * motors * power supplies * transformers * solenoids * PBXs * telephones * modems * key telephone systems * medical equipment * test instruments * industrial control circuits * computers * automotive small motor and electronics circuits Product dimensions (in millimeters) Part A B Cc D E number max. max. typ. min. max. RUEOSO 6.6 12.2 5.1 7.6 3.0 RUE110 6.6 14.2 5.1 7.6 3.0 RUE135 8.9 13.5 5.1 7.6 3.0 RUE160 8.9 15.2 5.1 7.6 3.0 RUE185 10.2 15.7 5.1 7.6 3.0 RUE250 11.4 18.3 5.1 7.6 3.0 RUE300 11.4 17.3 5.1 7.6 3.0 RUE400 14.0 20.1 5.1 7.6 3.0 RUE500 14.0 24.9 10.2 7.6 3.0 RUE600 16.5 24.9 10.2 7.6 3.0 RUE700 19.1 26.7 10.2 7.6 3.0 RUE800 21.6 29.2 10.2 7.6 3.0 RUE900 24.1 29.7 10.2 7.6 3.0 Lead size RUEOS90-RUE250 RUE300-RUE900 RUEO90-RUE250 0.51 mm (24 AWG) RUE300-RUESOO @ 0.81 mm (20 AWG) " A E ao Operating characteristics Maximum voltage 30 Vrms Maximum interrupt current* 40A Operating/storage temperature range 40C to 85C Maximum surface temperature Typical reset time 125C in tripped state <20 seconds (at 20C), atter power removed Device resistance in tripped state* V2/Pd * Note: Device may withstand higher interupt current at lower voltages. Each application will need to be individually qualified. "* Note: Device will reset when V/4R, <Pg (Ry_ = load resistance, V = circuit voltage, Pd = power dissipated in tripped state). Physical characteristics Lead material RUEOS90-250: 24 AWG Sn-plated Fe (= 0.51 mm) RUE300-900: 20 AWG Sn-plated Cu (= 0.81 mm) Soldering characteristics Soiderability per MIL-STD-202, Method 208E Solder heat withstand per MIL-STD-202, Method 210, Condition B Insulating material Cured, flame-retardant epoxy polymer, meets UL94V-O requirements Electrical characteristics (20C) Initial resistance Max. time Post trip resistance Part In I to trip Py R min. R max. Ri max. Number (A) (A) @ 5x! (s) {W) (Q) (Q) (Q) RUEOSO 0.90 1.80 5.9 0.6 0.070 0.12 0.22 RUE110 1.10 2.20 6.6 0.7 0,050 0.10 0.17 RUE135 1.35 2.70 7.3 0.8 0.040 0.08 0.13 RUE160 1.60 3.20 8.0 0.9 0.030 0.07 0.14 RUE185 1.85 3.70 8.7 1.0 0.030 0.06 0.09 RUE250 2.50 5.00 10.3 1.2 0.020 0.04 0.07 RUE300 3.00 6.00 10.8 2.0 0.020 0.05 0.08 RUE400 4.00 8.00 12.7 2.5 0.010 0.03 0.05 RUESOO 5.00 10.00 14.5 3.0 0.010 0.03 0.05 RUE600 6.00 12.00 16.0 3.5 0.005 0.02 0.04 RUE700 7.00 14.00 17.5 3.8 0.005 0.02 0.03 RUE800 8.00 16.00 18.8 4.0 0.005 0.02 0.02 RUESOO 9.00 18.00 20.0" 4.2 0.005 0.01 0.02 ly = Hold current. The maximum current at which the device will not trip at 20C. ly = Trip current. The minimum current at which the device will always trip at 20C. Pg = Typical power dissipation. Typical amount of power dissipated by the device when in tripped state in 20C still air environment, R min. = Minimum device resistance at 20C prior to tripping. R max. = Maximum device resistance at 20C prior to tripping. Ry max. = Maximum device resistance at 20C measured 1 hour post trip. * Device tested at 40 A. Environmental specifications Test Test method Conditions Resistance change Passive aging Raychem PS300 70C, 1000 hours 25% 85C, 1000 hours +5% Humidity aging Raychem PS300 85C, 85% R.H., 1000 hours 45% Thermal shock Raychem PS300 125C, -55C (ten times) +5% Solvent resistance Raychem PS300, Method 215 MIL-STD-202, Method 215F No change a4 Approvals and reference documents Agency approvals Reference documents UL-recognized component under file 74889, thermistor type devices (X6PU2) CSA-recognized component under file CA 78165-1 PS300 Test Methods and Requirements for PolySwitch Devices Performance curves Typical time to trip at 20C = RUEOSO = RUE110 = RUE135 = RUE160 = RUE185 = RUE250 = RUE300 = RUE400 = RUESOO = RUE600 = RUE700 = RUE800 M = RUESOO rFxACTTOMNMIOOyYD Time to trip (s) ABCDEFGHIJKLM 1000 100 01 .001 1 10 100 Fault current (A) Example: The typical time to trip of RUE110 at 8 A is 1 second. Thermal derating Percent of rated (at 20C) hold and trip current 200 150 100 50 -40 -30 -20 -10 0 10 20 30 40 50 60 #70 += 80 90 Temperature (C) Example: At 60C, the hold current of an RUE300 is 2.1 A and the trip current is 4.2 A70 percent af their rated values. Ordering information Packaging Bulk Tape and reel AMMO pack Product supplied in bags; multiples of 500 pieces per bag AUE090 through RUE250 available per EIA RS-468-A and IEC 286-2 RUE300 and RUE400 available per PolySwitch Tape and Reel Selection Guide* RUE090 through RUE250 available per EIA RS-468-A and IEC 286-2 RUE300 and RUE400 available per PolySwitch Tape and Reel Selection Guide * Note: PolySwitch Tape and Reel Selection Guide available upon request. Part numbering system RUEXXX - suffix -2 = Tape and reel - AP = AMMO pack -1. =25.4mm (1") minimum lead length XXX = Current rating Part marking system x-O0 | ~L_ Voltage rating PolySwitch symbol vOOU ~ Le Part |.D. (last three digits of part number) Second letter of part number OOO00 ~ Lo Lot number (may be on back) Caution Operation beyond maximum ratings may result in device damage and possible electrical arcing and flame. Note: These devices are intended for over- current/overtemperature protection, not for continual, repeated tripping. Raychem S.A. B.P. 8300 95802 CERGY PONTOISE Cedex FRANCE Tel (33) 1-34 20 24 07 Fax (33) 1-34 20 21 69 Raychem Limited Raychem GmbH Edison Road Haidgraben 6 DORCAN, SWINDON SN3 SJA 85521 OTTOBRUNN ENGLAND GERMANY Tel (49) 89 6089384 Tel (44) 1793 57 2245 Fax (49) 89 6089593 Fax (44) 1793 57 2209 All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Raychem makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Raychem's only obligations are those in the Raychem Standard Terms and Conditions of Sale for this product, and in no case will Raychem be liable for any incidental, indirect, or consequential damages arising from the sale, resale, veo ay mieiea atthe nracuct Gnarifications are subiect to change without notice. in addition, Raychem reserves the right fo make et a ee