ACDC
Specification
6501200 Watts
•Rugged Construction
•Variable Fan Speed for Noise Reduction
•20 ºC to +70 ºC Operation
•AC OK, Remote On/Off and Active Current Share
•5 V Standby
•Screw Terminals
•3 Year Warranty
MHP Series
Input
Input Voltage • 650 W: 80-264 VAC, derate output power
10% <90 VAC, and 20% <85 VAC,
1000 W: 85-264 VAC, derate output power
10% <90 VAC
Input Frequency • 47-63 Hz
Input Current • 650 W: 6.5 A at 115 VAC typical, 3.2 A at
230 VAC full load,
1000 W: 10.9 A at 115 VAC typical, 5.1 A
at 230 VAC full load
Inrush Current • 650 W: 40 A max at 264 VAC
1000 W: 60 A max at 264 VAC
Power Factor • >0.9
Earth Leakage Current • 250 µA max at 264 VAC/60 Hz
Input Protection • 650 W: T16 A/250 V, 1000 W: T20 A/250 V
internal fuse in line and neutral
Output
Output Voltage • 12-48 VDC (see tables)
Output Voltage Trim • ±10% V1
Initial Set Accuracy • 650 W: ±1% V1, ±5% V3,
1000 W: ±1% V1, ±5% V2
Minimum Load • No minimum load required
Start Up Delay • 500 ms max
Start Up Rise Time • 50 ms typical
Hold Up Time • 20 ms minimum
Drift • ±0.2% after 20 min warm up
Line Regulation • ±0.5%
Load Regulation • 650 W: ±1% V1, ±5% V3,
1000 W: ±1% V1, ±5% V2
Transient Response • 4% max. deviation, recovery to
within 1% in 500 µs for a 50-75-50%
load change
Ripple & Noise • 1% pk-pk V1, 20 MHz bandwidth
Overvoltage Protection • 115-145% Vnom, recycle input to reset
Overload Protection • 110-140%, V1 only
Overtemperature • Auto reset
Protection
Short Circuit Protection • Constant current characteristic
Temp. Coefficient • 0.05% / °C
Remote Sense • Compensates for 0.5 V total voltage drop
Remote On/Off • Uncommitted isolated optocoupler diode,
powered diode inhibits V1 and fan supply (1)
Current Share • Single wire current share (1)
(1) See longform datasheet for more information
xppower.com
General
Efficiency • 85% typical
Isolation • 4000 VAC In to Out, 2 x MOPP, 1500 VAC
In to Earth, 1 x MOPP, 500 VDC Out to
Earth
Switching Frequency • PFC 70 kHz, main converter 200 kHz,
standby 130 kHz typical
Power Density • 650 W: 8.2 W/in3,1000 W: 8.9 W/in3
Signals • AC OK, remote on/off, current share (1)
MTBF • 260 KHrs to MIL-HDBK-217F at 25 °C, GB
Environmental
Operating Temperature • -20 °C to +70 °C, derate linearly from
+50 °C at 2.5% / °C to 50% at +70 °C,
1000 W: -40 °C start up
Cooling • 650 W: Forced cooled, ‘-TF’ & ‘-EF’
models have integral dual voltage level fan,
which is load dependant, U Channel
requires 5.5 m/s minimum airflow,
1000 W: Forced cooled via integral quad
voltage level fan which is load dependant (1)
Operating Humidity • 95% RH, non-condensing
Storage Temperature • -40 °C to +85 °C
Operating Altitude • 3000 m
Shock • 30 g pk, half sine, 6 axes
Vibration • 2 g rms, 5 Hz to 500 kHz, 3 axes
EMC & Safety
Emissions • EN55022/ENN55011 class B conducted
EN55022/EN55011 class A radiated
Harmonic Currents • EN61000-3-2 class A,
650 W: class C for loads ≥20%
1000 W: classCfor loads ≥10%
Voltage Flicker • EN61000-3-3
ESD Immunity • EN61000-4-2, level 3 contact, level 3 air,
Perf Criteria A
Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A
EFT/Burst • EN61000-4-4, level 3 Perf Criteria A
Surge • EN61000-4-5, installation class 3,
Perf Criteria A
Conducted Immunity • EN61000-4-6, level 3, Perf Criteria A
Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms,
100% 5000 ms, Perf Criteria A, B, B,
EN60601-1-2, 30% 500 ms, 60% 100 ms,
100% 10 ms, 100% 5000 ms, Perf Criteria
A, A, A, B. Consult longform for 115 VAC
operation
Safety Approvals • IEC60601-1 CB report, CSA 22.2
No.60601-1, ANSI/AAMI ES60601-1, TUV,
EN60601-1 Including Risk Management
ACDC
MHP650
Models and Ratings
Notes
1. For top fan version replace ‘-EF’ in model number with ‘-TF’, e.g.
MHP650PS12-TF
2. For U Channel version remove suffix.
3. U Channel models require a minimum of 5.5 m/s airflow from the system.
4. Not available for ‘-TF’ and ‘-EF’ models as used by integral fan.
Output Voltage V1 Output Current V1 Fan Supply V2(4) Standby Supply V3 Output Power(3) Model Number(1,2)
12 V 50 A 12 V / 0.5 A 5 V / 0.2 A 607 W MHP650PS12-EF
15 V 40 A 12 V / 0.5 A 5 V / 0.2 A 607 W MHP650PS15-EF
24 V 27 A 12 V / 0.5 A 5 V / 0.2 A 655 W MHP650PS24-EF
28 V 23 A 12 V / 0.5 A 5 V / 0.2 A 655 W MHP650PS28-EF
36 V 18 A 12 V / 0.5 A 5 V / 0.2 A 655 W MHP650PS36-EF
48 V 13.5 A 12 V / 0.5 A 5 V / 0.2 A 655 W MHP650PS48-EF
Mechanical Details
End Fan (See Longform Datasheet for UChannel Version)
1. Dimensions shown in inches (mm).
2. Weight: 2.8 lb (1.27 kg).
3. J2 Mating plug: JST part no. PHDR-10VS,
contact: 26-22 AWG JST part no. SPHD-001T-P0.5.
Notes
Vo+Vo-
Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
Standard Terminal
Block, M3.5 Screw 3
Pins 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
9.18 (233.2)
N
E
L
2.50 (63.5)
V1 Adjustment
Output On, LED
1.95
(49.5)
2.49
(63.3)
AIRFLOW
Pin 1
Pin 9
Pin 2
Pin 10
J3: Logic Connector
0.87
(22.2)
2.86 (72.6)
6.53 (165.8)
8.00 (203.2)
4.00
(101.6)
C
L
2 x M3 THD both side faces
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
4 x M3 THD
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
J2 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit (Anode)
8 - Inhibit (Cathode)
9 +5 V Standby (V3)
10 5 V Standby Return (V3)
Top Fan (Suffix TF)
Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
Standard Terminal Block, M3.5 Screw 3, Pins 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
Vo+Vo-
N
E
8.00 (203.2)
L
2.58 (65.5)
2.50 (63.5)
1.95
(49.5)
0.87
(22.2)
6.53 (165.8)
2.86 (72.6)
4.00
(101.6)
Pin 1
pin 9
Pin 2
Pin 10
J3: Logic Connector
V1 Adjustment
Output On, LED
AIRFLOW
2 x M3 THD both side faces
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
4x M3 THD
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
Signals
AC OK/Power Fail Remote On/Off (Inhibit)
AC OK Collector
Pin 3
AC OK Emitter
Pin 2 (-sense)
POWER SUPPLY
Transistor On (<0.8 V):
AC NOT OK
Transistor Off (>4.5 V):
AC OK
INHIBIT HI INHIBIT LOW
J3 Logic Connector
330R
5 V Standby
Return Pin 10
5 V Standby
Pin 9
Max 12 V 20 mA Inhibit Hi
Pin 7
POWER SUPPLY
100 R
800 R
2-5 mA
Chassis J3 Logic Connector
Signal High: Power Supply OFF
Low or Floating: Power Supply ON
Signal High: Power Supply ON
Low or Floating: Power Supply OFF
Inhibit Lo
Pin 8
5 V Standby
Pin 9
5 V Standby
Return Pin 10
Inhibit Hi
Pin 7
POWER SUPPLY
100 R
Chassis J3 Logic Connector
Inhibit Lo
Pin 8
5 V Standby
Pin 9
5 V Standby
Return Pin 10
800 R
2-5 mA
Notes
J2 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit (Anode)
8 - Inhibit (Cathode)
9 +5 V Standby (V3)
10 5 V Standby Return (V3)
1. Dimensions shown in inches (mm).
2. Weight: 2.8 lb (1.27 kg).
3. J2 Mating plug: JST part no. PHDR-10VS,
contact: 26-22 AWG JST part no. SPHD-001T-P0.5.
ACDC
MHP650
Mechanical Details
For U Channel and Thermal Considerations please see longform datasheet.
22-Feb-13
ACDC
MHP1000
Mechanical Details
Models and Ratings
Output Voltage V1 Output Current V1 Standby Supply V2 Output Power Model Number
<180 VAC >180 VAC <180 VAC >180 VAC
12 V 83.0 A 5 V / 1.0 A 1000 W MHP1000PS12
15 V 67.0 A 5 V / 1.0 A 1010 W MHP1000PS15
24 V 42.0 A 50.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS24
28 V 36.0 A 43.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS28
36 V 28.0 A 34.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS36
48 V 21.0 A 25.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS48
1. Dimensions shown in inches (mm).
2. Weight: 4.6 lb (2.08 kg)
3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22
AWG JST part no. SPHD-001T-P0.5.
Notes
C
L
4.50
(114.3)
1.20 (30.5)
Pin 2 Pin 1
Pin 10 Pin 9
Detail A J3: Logic Connector
9.41 (238.9)
BB
BB
BB
4 x M4-0.7 THD both side faces
0.15 (3.8) max screw penetration
max torque 10.62 lbs-in (1.2 Nm)
4 x M4-0.7 THD both side faces
0.15 (3.8) max screw penetration
max torque 10.62 lbs-in (1.2 Nm)
Airflow
1.33 (33.8)
6.70 (170.2)
VO+ VO-
L
N
A
9.48 (240.9)
5.90
(149.8)
2.91
(73.9)
1.20 (30.5)
1.47
(37.4)
9.55 (242.64)
2.40 (61.0)
V1 Adjustment
Output On, LED
Standard Terminal Block, M4 Screw
3 Pins 0.37 (9.5) center
Torque 10.62 lbs-in (1.2 Nm)
Standard Terminal Block, M6 Screw, 4 Pins 0.62 (16.0) center
Torque 26.0 lbs-in (2.94 Nm)
J3 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit
8 - Inhibit
9 +5 V Standby
10 -5 V Standby