Features
Fast read access time – 90ns
Dual voltage range operation
Low voltage power supply range, 3.0V to 3.6V, or
Standard power supply range, 5V 10%
Compatible with JEDEC standard Atmel® AT27C256R
Low-power CMOS operation
20µA max standby (less than 1µA, typical) for VCC = 3.6V
29mW max active at 5MHz for VCC = 3.6V
JEDEC standard package
32-lead PLCC
High-reliability CMOS technology
2,000V ESD protection
200mA latchup immunity
Rapid programming algorithm – 100µs/byte (typical)
CMOS- and TTL-compatible inputs and outputs
JEDEC standard for LVTTL
Integrated product identification code
Industrial temperature range
Green (Pb/halide-free) packaging option
1. Description
The Atmel AT27LV256A is a high-performance, low-power, low-voltage, 262,144-bit, one-
time programmable, read-only memory (OTP EPROM) organized as 32K by 8 bits. It
requires only one supply in the range of 3.0V to 3.6V in normal read mode operation, mak-
ing it ideal for fast, portable systems using battery power.
The Atmel innovative design techniques provide fast speeds that rival 5V parts, while keep-
ing the low power consumption of a 3.3V supply. At VCC = 3.0V, any byte can be accessed
in less than 90ns. With a typical power dissipation of only 18mW at 5MHz and VCC = 3.3V,
the AT27LV256A consumes less than one-fifth the power of a standard, 5V EPROM.
Standby mode supply current is typically less than 1µA at 3.3V.
The AT27LV256A is available in an industry-standard, JEDEC-approved, one-time program-
mable (OTP) PLCC package. All devices feature two-line control (CE, OE) to give
designers the flexibility to prevent bus contention.
The AT27LV256A operating with VCC at 3.0V produces TTL-level outputs that are compati-
ble with standard TTL logic devices operating at VCC = 5.0V. The device is also capable of
standard, 5V operation, making it ideally suited for dual supply range systems or card prod-
ucts that are pluggable in both 3V and 5V hosts.
The AT27LV256A has additional features to ensure high quality and efficient production use.
The rapid programming algorithm reduces the time required to program the part and guar-
antees reliable programming. Programming time is typically only 100µs/byte. The
integrated product identification code electronically identifies the device and manufacturer.
This feature is used by industry standard programming equipment to select the proper pro-
gramming algorithms and voltages. The AT27LV256A programs in exactly the same way as
a standard, 5V Atmel AT27C256R, and uses the same programming equipment.
256K (32K x 8)
Low Voltage,
One-time
Programmable,
Read-only Memory
Atmel AT27LV256A
0547H–EPROM–4/11
2
0547H–EPROM–4/11
Atmel AT27LV256A
2. Pin configurations
3. System considerations
Switching between active and standby conditions via the chip enable pin may produce transient voltage excursions. Unless
accommodated by the system design, these transients may exceed datasheet limits, resulting in device nonconformance.
At a minimum, a 0.1µF, high-frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This
capacitor should be connected between the VCC and ground terminals of the device, as close to the device as possible.
Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7µF bulk electrolytic
capacitor should be utilized, again connected between the VCC and ground terminals. This capacitor should be positioned as
close as possible to the point where the power supply is connected to the array.
Figure 3-1. Block diagram
Pin name Function
A0 - A14 Addresses
O0 - O7 Outputs
CE Chip Enable
OE Output Enable
NC No Connect
5
6
7
8
9
10
11
12
13
29
28
27
26
25
24
23
22
21
A6
A5
A4
A3
A2
A1
A0
NC
O0
A8
A9
A11
NC
OE
A10
CE
O7
O6
4
3
2
1
32
31
30
14
15
16
17
18
19
20
O1
O2
GND
NC
O3
O4
O5
A7
A12
VPP
NC
VCC
A14
A13
32-lead PLCC
Top view
Note: PLCC package pins 1
and 17 are “don’t
connect.”
3
0547H–EPROM–4/11
Atmel AT27LV256A
4. Absolute maximum ratings*
Note: 1. Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20ns. Maximum output pin voltage is
VCC + 0.75V DC, which may be exceeded if certain precautions are observed (consult application notes), and which may
overshoot to +7.0V for pulses of less than 20ns.
5. DC and AC characteristics
Table 5-1. Operating modes
Notes: 1. X can be VIL or VIH.
2. Read, output disable, and standby modes require 3.0V VCC 3.6V or 4.5V VCC 5.5V.
3. Refer to programming characteristics. Programming modes require VCC = 6.5V.
4. VH = 12.0 ± 0.5V.
5. Two identifier bytes may be selected. All Ai inputs are held low (VIL) except A9, which is set to VH, and A0, which is tog-
gled low (VIL) to select the manufacturer’s identification byte and high (VIH) to select the device code byte.
Table 5-2. DC and AC operating conditions for read operation
Temperature under bias . . . . . . . . . . . . . . . -40°C to +85°C *NOTICE: Stresses beyond those listed under “Absolute
maximum ratings” may cause permanent damage to
the device. This is a stress rating only, and functional
operation of the device at these or any other conditions
beyond those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
Storage temperature . . . . . . . . . . . . . . . . .-65°C to +125°C
Voltage on any pin with
respect to ground . . . . . . . . . . . . . . . . . . . -2.0V to +7.0V(1)
Voltage on A9 with
respect to ground . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1)
VPP supply voltage with
respect to ground . . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1)
Mode/Pin CE OE Ai VPP VCC Outputs
Read(2) VIL VIL Ai VCC VCC DOUT
Output disable(2) VIL VIH X
(1) VCC VCC High Z
Standby(2) VIH X
(1) X
(1) VCC VCC High Z
Rapid program(3) VIL VIH Ai VPP VCC DIN
PGM verify(3) X
(1) VIL Ai VPP VCC DOUT
Optional PGM verify(3) VIL VIL Ai VCC VCC DOUT
PGM inhibit(3) VIH VIH X
(1) VPP VCC High Z
Product identification(3)(5) VIL VIL
A9 = VH(4)
A0 = VIH or VIL
A1 - A14 = VIL
VCC VCC Identification code
Atmel AT27LV256A
-90
Industrial operating temperature (case) -40°C - 85°C
VCC power supply
3.0V to 3.6V
5V 10%
4
0547H–EPROM–4/11
Atmel AT27LV256A
Table 5-3. DC and operating characteristics for read operation
Notes: 1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP.
2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and
IPP.
Table 5-4. AC characteristics for read operation
Symbol Parameter Condition Min Max Units
VCC = 3.0V to 3.6V
ILI Input load current VIN = 0V to VCC A
ILO Output leakage current VOUT = 0V to VCC A
IPP1(2) VPP(1) read/standby current VPP = VCC 10 µA
ISB VCC(1) standby current
ISB1 (CMOS), CE = VCC 0.3V 20 µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V 100 µA
ICC VCC active current f = 5MHz, IOUT = 0mA, CE = VIL 8mA
VIL Input low voltage -0.6 0.8 V
VIH Input high voltage 2.0 VCC + 0.5 V
VOL Output low voltage IOL = 2.0mA 0.4 V
VOH Output high voltage IOH = -2.0mA 2.4 V
VCC = 4.5V to 5.5V
ILI Input load current VIN = 0V to VCC A
ILO Output leakage current VOUT = 0V to VCC A
IPP1(2) VPP(1) read/standby current VPP = VCC 10 µA
ISB VCC(1) standby current
ISB1 (CMOS), CE = VCC 0.3V 100 µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V 1 mA
ICC VCC active current f = 5MHz, IOUT = 0mA, CE = VIL 20 mA
VIL Input low voltage -0.6 0.8 V
VIH Input high voltage 2.0 VCC + 0.5 V
VOL Output low voltage IOL = 2.1mA 0.4 V
VOH Output high voltage IOH = -400µA 2.4 V
VCC = 3.0V to 3.6V and 4.5V to 5.5V
Symbol Parameter Condition
Atmel AT27LV256A
Units
-90
Min Max
tACC(3) Address to output delay CE = OE = VIL 90 ns
tCE(2) CE to output delay OE = VIL 90 ns
tOE(2)(3) OE to output delay CE = VIL 50 ns
tDF(4)(5) OE or CE high to output float, whichever occurred first 40 ns
tOH Output hold from address, CE or OE, whichever occurred first 0 ns
5
0547H–EPROM–4/11
Atmel AT27LV256A
Figure 5-1. AC waveforms for read operation(1)
Notes: 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE.
3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC.
4. This parameter is only sampled, and is not 100% tested.
5. Output float is defined as the point when data is no longer driven.
Figure 5-2. Input test waveforms and measurement levels
Figure 5-3. Output test load
tR, tF < 20ns (10% to 90%)
Note: CL = 100pF including
jig capacitance.
6
0547H–EPROM–4/11
Atmel AT27LV256A
Table 5-5. Pin capacitance
Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
Figure 5-4. Programming waveforms(1)
Notes: 1. The input timing reference is 0.8V for VIL and 2.0V for VIH.
2. tOE and tDFP are characteristics of the device, but must be accommodated by the programmer.
3. When programming the Atmel AT27LV256A, a 0.1µF capacitor is required across VPP and ground to suppress spurious
voltage transients.
f = 1MHz, T = 25°C(1)
Symbol Typ Max Units Conditions
CIN 48pFVIN = 0V
COUT 812pFVOUT = 0V
7
0547H–EPROM–4/11
Atmel AT27LV256A
Table 5-6. DC programming characteristics
Table 5-7. AC programming characteristics
Notes: 1. VCC must be applied simultaneously with or before VPP and removed simultaneously with or after VPP.
2. This parameter is only sampled, and is not 100% tested. Output float is defined as the point where data is no longer driven.
See timing diagram.
3. Program pulse width tolerance is 100µsec5%.
Table 5-8. The Atmel AT27LV256A integrated product identification code(1)
Note: 1. The Atmel AT27LV256A has the same product identification code as the Atmel AT27C256R. Both are programming
compatible.
TA = 25 5°C, VCC = 6.5 0.25V, VPP = 13.0 0.25V
Symbol Parameter Test conditions
Limits
UnitsMin Max
ILI Input load current VIN = VIL, VIH 10 µA
VIL Input low level -0.6 0.8 V
VIH Input high level 2.0 VCC + 0.5 V
VOL Output low voltage IOL = 2.1mA 0.4 V
VOH Output high voltage IOH = -400µA 2.4 V
ICC2 VCC supply current (program and verify) 25 mA
IPP2 VPP current CE = VIL 25 mA
VID A9 product identification voltage 11.5 12.5 V
TA = 25 5°C, VCC = 6.5 0.25V, VPP = 13.0 0.25V
Symbol Parameter Test conditions(1)
Limits
UnitsMin Max
tAS Address setup time
Input rise and fall times
(10% to 90%) 20ns
Input pulse levels
0.45V to 2.4V
Input timing reference level
0.8V to 2.0V
Output timing reference level
0.8V to 2.0V
s
tOES OE setup time 2 µs
tDS Data setup time 2 µs
tAH Address hold time 0 µs
tDH Data hold time 2 µs
tDFP OE high to output float delay(2) 0 130 ns
tVPS VPP setup time 2 µs
tVCS VCC setup time 2 µs
tPW CE program pulse width(3) 95 105 µs
tOE Data valid from OE(2) 150 ns
tPRT VPP pulse rise time during programming 50 ns
Codes
Pins
Hex dataA0 O7 O6 O5 O4 O3 O2 O1 O0
Manufacturer 0 0 0 0 1 1 1 1 0 1E
Device type 1 1 0 0 0 1 1 0 0 8C
8
0547H–EPROM–4/11
Atmel AT27LV256A
6. Rapid programming algorithm
A 100µs CE pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised to
13.0V. Each address is first programmed with one 100µs CE pulse without verification. Then a verification/reprogramming
loop is executed for each address. In the event a byte fails to pass verification, up to 10 successive 100µs pulses are
applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been applied, the part is
considered failed. After the byte verifies properly, the next address is selected until all have been checked. VPP is then
lowered to 5.0V and VCC to 5.0V. All bytes are read again and compared with the original data to determine if the device
passes or fails.
Figure 6-1. Rapid programming algorithm
9
0547H–EPROM–4/11
Atmel AT27LV256A
7. Ordering information
Green package option (Pb/halide-free)
tACC
(ns)
ICC (mA)
Atmel ordering code Package Lead finish Operation rangeActive Standby
90 8 0.02 AT27LV256A-90JU 32J Matte tin Industrial
(-40C to 85C)
Package type
32J 32-lead, plastic, J-leaded chip carrier (PLCC)
10
0547H–EPROM–4/11
Atmel AT27LV256A
8. Packaging information
32J – PLCC
DRAWING NO. REV.
TITLE
32J, 32-lead, plastic J-leaded chip carrier (PLCC) B
32J
10/04/01
1.14(0.045) X 45° PIN NO. 1
IDENTIFIER
1.14(0.045) X 45°
0.51(0.020)MAX
0.318(0.0125)
0.191(0.0075)
A2
45° MAX (3X)
A
A1
B1 E2
B
e
E1 E
D1
D
D2
COMMON DIMENSIONS
(Unit of measure = mm)
SYMBOL MIN NOM MAX NOTE
Package drawing contact:
packagedrawings@atmel.com
Notes: 1. This package conforms to JEDEC reference MS-016, variation AE.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.10mm) maximum.
A 3.175 3.556
A1 1.524 2.413
A2 0.381
D 12.319 12.573
D1 11.354 11.506 Note 2
D2 9.906 10.922
E 14.859 15.113
E1 13.894 14.046 Note 2
E2 12.471 13.487
B 0.660 0.813
B1 0.330 0.533
e 1.270 TYP
11
0547H–EPROM–4/11
Atmel AT27LV256A
9. Revision history
Doc. rev. Date Comments
0547E 04/2011 Remove SOIC and TSOP packages
Add lead finish to ordering information
0547D 12/2007
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: (+1) (408) 441-0311
Fax: (+1) (408) 487-2600
www.atmel.com
Atmel Asia Limited
Unit 01-5 & 16, 19F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Atmel Munich GmbH
Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81) (3) 3523-3551
Fax: (+81) (3) 3523-7581
© 2011 Atmel Corporation. All rights reserved. / Rev.: 0547H–EPROM–4/11
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel
products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY
RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE
THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to
make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not
be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
Atmel®, logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trade-
marks of others.