1
New Product News
USB Connectors
XM7
Small Interface Connectors That
Conform to USB Standards
• Insertion life of 5,000 insertions.
• Right-angle DIP terminals or right-angle SMT terminals.
• USB A-type sockets for mounting on personal computers and
USB hubs. USB B-type sockets for mounting on printers, scan-
ner, mouses, and other peripheral devices for computers.
mini-USB Connectors
USB Connectors
RoHS Compliant
XM7D mini-USB Connectors
■Model Number Legend
■Ordering Information
●Sockets
Appearance
Right-angle DIP terminals Right-angle SMT terminals
Model XM7D-0512 XM7D-0514
Minimum ordering
quantity (pieces) 100 50
XM7D-05 1 @
1 2 3 4
1 Type
D: mini-B-type socket
2 No. of Contacts
05: 5 contacts
3 Plating Specification
1: Gold plated
4 Terminal Shape
2: Right-angle DIP terminals
4: Right-angle SMT terminals
XM7
2
■Ratings and Characteristics ■Materials
■Dimensions (Unit: mm)
Rated current 1 A
Rated voltage 30 V
Insulation resistance 100 MΩ min.
Contact resistance 50 mΩ max.
Dielectric strength 100 VAC for 1 min
(leakage current: 0.5 mA max.)
Total insertion force 35 N max.
Total removal force 7 N min.
Insertion durability 5,000 insertions
Ambient operating temperature 0 to 50°C (with no icing)
Housing LCP resin
Contacts Copper alloy
Shell Copper alloy
6.9
7.7
5.87
2
3.2
7.3
0.8
1.8
4
3.1 3.9
0.4
1.25 1.2
0.25
4.75
0.6 1.6
Five, 0.7 dia.
+0.1
0
7.4
±0.1
4.75
±0.1
3.2
±0.05
0.8
±0.05
0.8
±0.05
1.9
±0.05
1.2
±0.05
9.85
±0.3
9.2
0.9
±0.05
PCB Mating Dimensions
(BOTTOM VIEW)
XM7D-0512
6.9
7.7
5.87
3.1 3.9
5.5
±0.1
8.8
±0.1
2
±0.05
2.5
±0.05
2.5
±0.05
3.2
±0.05
0.8
±0.05
0.5
±0.05
9.25
±0.3
5.5
1.5
1.5
0.9
0.4
0.8
PCB Mating Dimensions
(TOP VIEW)
XM7D-0514
3
XM7
XM7A/B USB Connectors
■Model Number Legend
■Ordering Information
●Sockets
■Ratings and Characteristics
■Materials and Finish
Item Type One A-type Socket One A-type Socket Two Stacked A-type Sockets One B-type Socket
Appearance
With straight DIP kinked
terminals
With right-angle DIP kinked
terminals
With right-angle DIP kinked
terminals With right-angle DIP kinked
terminals
Model XM7A-0441 XM7A-0442 XM7A-0442-A XM7B-0442
Minimum ordering
quantity (pieces) 120 150 120 150
XM7@-04 4 @-@
1 2 3 4 5
1 Type
A: A-type socket
B: B-type socket
2 No. of Contacts
04: 4 contacts
3 Plating Specification
4: Gold plated
4 Terminal Shape
1: Straight (A-type sockets only)
2: Right angle
5 Special Code
A-type sockets Blank: 1 socket (black housing)
A: 2 stacked sockets (black housing)
B-type sockets Blank: White housing
Rated current 1 A
Rated voltage 30 VAC
Contact resistance 30 mΩ max. (at 20 mV, 100 mA max. (excluding cable conductor resistance))
Insulation resistance 1,000 MΩ min. (at 500 VDC)
Dielectric strength 750 VAC for 1 min (leakage current: 0.5 mA max.)
Total insertion force 35.3 N max.
Total removal force 10 N min.
Insertion durability 1,500 insertions
Ambient operating temperature −40 to 60°C (with no icing)
Item Classification Sockets
Type A-type Sockets B-type Sockets
Housing Fiber-glass reinforced
PBT resin (UL94V-0)/black
Fiber-glass reinforced
PBT resin (UL94V-0)/white
Contacts Mating end Phosphor bronze/nickel base, gold plating
Terminals Phosphor bronze/nickel base, tin alloy plated
Shell Copper alloy/tin plated
XM7
4
■Dimensions (Unit: mm)
5.127.12
14.5
12.5
Contact No.1 Contact No.4
(15.6)
7
2
15.0
(0.5) 2.8
2.71 5.72
1.4±0.25
3.07
±0.1
Two, 2.3±0.08 dia.
Four, 0.92±0.08 dia.
13.14
±0.1
7.0
±0.1
2.0
±0.1
2.5
±0.1
2.71
±0.1
Contact No.4Contact No.1
Mounting holes
(t = 1.6 mm, bottom view)
XM7A-0441
One A-type Socket
12.5
2
7
(16.2)
14.5
Contact No. 4 14.0
4.13
10.28 2.71
2.84 3.72
6.99
(11.4)
Contact No. 1
7.12 5.12
3.07±0.1
Two, 2.3 ±0.08 dia.
Four, 0.92 ±0.08 dia.
13.14±0.1
7.0±0.1
2.0±0.1
2.5±0.1
2.71±0.1
Mounting holes
(t = 1.6 mm, bottom view)
Contact No. 4Contact No. 1
XM7A-0442
One A-type Socket
14.5
Top contact No. 1
Bottom contact No. 1
Top contact No. 4
Bottom contact No. 4
Bottom contact
Top contact No. 1
Top contact
Top contact No. 4
Bottom contact No. 1 Bottom contact No. 4
12.5
(19.9)
13.62 15.62
0.5
15.49
2.0±0.1
5.68±0.1
3.07±0.1
13.14±0.1
Four, 2.3 ±0.08 dia.
Eight, 0.92 ±0.08 dia.
5.33±0.1
2.71±0.1
7.0±0.1
3.72
2.84
2.71
5.33
5.6810.28
16.96
8.5
5.12
2
7
(15.6)
5.12
Mounting holes
(t = 1.6 mm, bottom view)
XM7A-0442-A
Two Stacked A-type Sockets
5
XM7
■Accessories (sold separately) (Unit: mm)
●Dust cover (For XM7A One A-type socket)
XM7Z-0001 (A type)
●Dust cover (For XM7B sockets)
XM7Z-0002 (B type) Characteristics/Material
Note: Dust covers cannot be used for Two Stacked A-type sockets.
(14.7)
2.5
7.78 10.62
16
11
2.91
22.71
10.28
3.1
5.5
8.45
12.04
Contact No. 2 Contact No. 1
Contact No. 3 Contact No. 4
Contact No. 4Contact No. 3
Contact No. 1Contact No. 2
Contact
No. 3
Contact
No. 2
Contact
No. 1
Contact
No. 4
(15.2)
2
±0.1
2.71
±0.1
12.04
±0.1
Two, 2.3 ±0.08 dia.
2.5
±0.1
4.77
±0.1
Four, 0.92 ±0.08 dia.
Mounting holes
(t = 1.6 mm, bottom view)
XM7B-0442
One B-type Socket
16.8
1.4
7.5
12.3
2.35
10
14.2
8
6.4
1.4
13 7.4
Ambient operating
temperature −40 to 60°C
Material Polyethylene resin
Model Applicable Minimum ordering quantity
(pieces)
XM7Z-0001 XM7A (One A-type Socket) 50
XM7Z-0002 XM7B
XM7
6
■Precautions
●Automatic Soldering
Reference Information: Automated Soldering Conditions
(Jet Flow)
(1) Soldering temperature: 250 ±5°C
(2) Continuous soldering time: 5 ±1 s max.
●Soldering Conditions
• Reference Information: Reflow Conditions
Maximum temperature: 260°C
Time: 5 to 15 s max.
These conditions, however, depend on the type of solder, the
manufacturer, the amount of solder, the size of the board, and
the other mounting materials.
●Screen Thickness for Printing Cream Solder
We recommend a metal mask thickness of 0.15 mm when print-
ing cream solder.
The appropriate conditions, however, depend on the type of sol-
der, the manufacturer, the amount of solder, the size of the circuit
board, other mounting materials, and other conditions.
●Terminal Shapes
The terminals will deform if they are subjected to an excessive
load, which will in turn reduce solderability when mounting. Do
not drop the Connectors or handle them carelessly. Do not con-
nect anything when the Connectors are not mounted to a board.
Doing so may deform the terminals.
●Using an Automatic Solder Bath after Reflow
Mask the mating portion with tape before you perform automatic
soldering to prevent flux or solder from entering the mating por-
tion of the Connector. Select and use a suitable masking tape.
●Application Precautions
• Confirm that there is no excessive misalignment or inclination
in the mating contact portion between the plug and socket
before mating the Connector. Make sure that the Connector is
mated all the way to the back. If the Connector is not mated all
the way to the back, contact reliability may be lost.
• Do not apply an extreme load during Connector insertion or
removal. The Connector may be damaged, and contact failure
may result. Twist the plug and socket as little as possible when
mating the Connector. Not doing so may deform the terminals
or housing or crack the housing.
• Do not insert a foreign object, such as tweezers, into the Con-
nector mating contact portion. Doing so may cause the plating
to peel off or deform the terminals.
●Precautions for Board Mounting
Be careful of the amount of board warping. If the board is exces-
sively warped, soldering faults may occur.
●Storage
Do not store the Connectors in locations subject to dust or high
humidity. Do not store the Connectors in locations close to
sources of gasses such ammonia gas or sulfide gas.
Precautions for Correct Use
Preheating time:
60 s max.
Soldering time:
5 to 15 s max.
Preheating temperature
Soldering temperature
Peak temperature
(°C)
(s)
150
250
260
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products
or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,
to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price
of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other
claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it
to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice
to change part numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be
assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to
confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
G079-E1-01 0813 (0813)
2013
