CAT.8100D
4
5
6.3
6.3
12
23
37
49
ALUMINUM ELECTROLYTIC CAPACITORS
U
1
U
2
P
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
S
14
Capacitance tolerance (±20%)
Configuration
Taping code
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Voltage mark for 6.3V is 6V
Voltage
Capacitance
105˚C Marking
Lot No.
A2P
10
16V
Plastic platform
0.3 MAX.
5.8±0.3
φD±0.5
B±0.2
C±0.2
0.5 MAX.
A±0.2 A±0.2
E
0.5 to 0.8
φD
A
B
C
E
1.8
4.3
4.3
1.0
2.1
5.3
5.3
1.3
2.4
6.6
6.6
2.2
4 5
(mm)
6.3
UP series
6mmL Chip Type, Bi-Polarized
Chip type, bi-polarized withstanding high temperature range up to +105
°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Chip Type
Dimensions
Type numbering system (Example : 16V 10
µ
F)
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Resistance to soldering
heat
Shelf Life
Marking
Performance CharacteristicsItem
–55 to +105°C
6.3 to 50V
0.1 to 47µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater.
Black print on the case top.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
UP
Measurement frequency : 120Hz at 20°C
Measurement frequency : 120Hz
Rated voltage (V)
tan δ (MAX.)
6.3
0.24
10
0.20
16
0.17
25
0.17
35
0.15
50
0.15
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
6.3
4
8
10
3
6
16
2
4
25
2
4
35
2
3
50
2
3
Rated ripple current (mArms) at 105°C 120Hz
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
5
6.3
6.3
28
37
45
4
6.3
6.3
17
33
41
5
5
6.3
12
16
27
4
5
5
6.3
8.4
16
18
29
4
4
4
4
4
5
5
6.3
1.0
2.0
2.8
4.0
8.4
13
17
20
0J
6.3
1A
10
1C
16
1E
25
1V
35
1H
50
V
Code
Cap.(µF)
Capacitance change
Leakage current
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 1000 hours at
105°C with the polarity every 250 hours.
tan δ
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Rated
ripple
High
Te m p e ra tu re
WP
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UN(p.162) series if high CV products are required.
Please refer to page 3 for the minimum order quantity.
Case size
φD (mm)
UN
Extended
range
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz 120 Hz 300 Hz 1 kHz
10 kHz or more
0.70 1.00 1.17 1.36 1.50
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Nichicon:
UUP1E100MCL1GS UUP1C220MCL1GS UUP1E4R7MCL1GS UUP1H4R7MCL1GS UUP1V4R7MCL1GS
UUP0J220MCL1GS UUP0J330MCL1GS UUP0J470MCL1GS UUP1A100MCL1GS UUP1A220MCL1GS
UUP1A330MCL1GS UUP1C4R7MCL1GS UUP1C330MCL1GS UUP1E3R3MCL1GS UUP1V2R2MCL1GS
UUP1V3R3MCL1GS UUP1H0R1MCL1GS UUP1HR22MCL1GS UUP1HR33MCL1GS UUP1HR47MCL1GS
UUP1H010MCL1GS UUP1H2R2MCL1GS UUP1H3R3MCL1GS UUP1C100MCL1GS UUP1V100MCL1GS
UUP1HR47MCL1GB
