RH119
1
I.D.No.66-10-0176 Rev. D
For more information www.analog.comDocument Feedback
PACKAGE/ORDER INFORMATION
BURN-IN CIRCUIT
DESCRIPTION
High Performance
Dual Comparator
The RH
®
119 dual comparator features low input offset
voltage and offset current, high voltage gain, guaranteed
common mode rejection and input protection diodes.
The RH119 is capable of operation over a supply range
from 5V to ±15V and can drive 25mA loads from each
open collector output. A separate GND pin allows the
RH119 to isolate system grounds.
The wafer lots are processed to Analog Devices’ in-house
Class S flow to yield circuits usable in stringent military
applications.
All registered trademarks and trademarks are the property of their respective owners. Protected
by U.S. patents, including XXXXX, XXXXX.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage ..........................................................36V
Output to Negative Supply Voltage .......................... 36V
Ground to Negative Supply Voltage ......................... 25V
Ground to Positive Supply Voltage .......................... 18V
Diffierential Input Voltage ....................................... ± 5V
Differential Input Current ..................................... ±5mA
Input Voltage (See Note 1)
Output Short-Circuit Duration ............................. 10 sec
Operating Temperature Range .............. –55°C to 125°C
Storage Temperature Range ..................–65°C to 150°C
Lead Temperature (Soldering, 10 sec) ................... 300°C
–
+
–
+
15V
SIDE 1
SIDE 2
10k
10k
100Ω
10k
GND1
GND2
OUT1
OUT2
V+
V–
–15V RH119 BI
TOP VIEW
–IN2
V+
V–
–IN1
10 9
5
2
6
H PACKAGE
10-LEAD TO-5 METAL CAN
8
4
GND2
+IN2
OUT2
+IN1
GND1
OUT1
7
3
1
1
2
3
4
5
6
7
TOP VIEW
J PACKAGE
14-LEAD CERDIP
14
13
12
11
10
9
8
NC
NC
GND1
+IN1
–IN1
V–
OUT2
NC
NC
OUT1
V+
–IN2
+IN2
GND2
TOP VIEW
W PACKAGE
10-LEAD CERPAC
1
5
4
3
2
10
6
7
8
9
OUT1
GND1
+IN1
–IN1
V–
V+
–IN2
+IN2
GND2
OUT2
Note: Obsolete Packages-For Reference Only
RH119
2
I.D.No.66-10-0176 Rev. D
For more information www.analog.com
TABLE 1: ELECTRICAL CHARACTERISTICS
TABLE 1A: ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS NOTES
TA = 25˚CSUB-
GROUP
−55˚C ≤ TA ≤ 125˚CSUB-
GROUP UNITSMIN TYP MAX MIN TYP MAX
VOS Input Offset Voltage VS = ±15V, VCM = 0V
3
4 1
7
2, 3
mV
mV
CMRR Common Mode
Rejection Ratio
90 1 dB
IOS Input Offset Current 375 1 100 2, 3 nA
IBInput Bias Current 500 1 1000 2, 3 nA
AVVoltage Gain 10 4 V/mV
tRResponse Time 480 200 4 200 5, 6 ns
VSAT Saturation Voltage VIN ≤ −5mV, IO = 25mA 1.5 1 V
V+ ≥ 4.5V, V− = 0V
VIN ≤ 6mV, ISINK ≤ 3.2mA
TA ≥ 0˚C
TA ≤ 0˚C
0.4
1
0.4
0.6
2
3
V
V
Output Leakage Current VIN ≥ 5mV, VOUT to V− = 35V 2 1 10 2, 3 µA
Input Voltage Range VS = ±15V
V+ = 5V, V− = 0V
−12
1
12
3
1
1
12
3
2, 3
2, 3
V
V
Differential Input Voltage ±5 1 ±5 2, 3 V
ISSupply Current V+ = 5V, V− = 0V 4.3 mA
Positive Supply Current VS = ±15V 11.5 1 mA
Negative Supply Current VS = ±15V 4.5 1 mA
(Postirradiation) (Note 5)
SYMBOL PARAMETER CONDITIONS NOTES
10Krad(Si) 20Krad(Si) 50Krad(Si) 100Krad(Si) 200Krad(Si
UNITSMIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
VOS Offset Voltage 4 4 4 4 8 mV
IOS Input Offset Current 3 75 100 150 300 500 nA
IBInput Bias Current 3 500 750 1000 1500 2000 nA
AVOL Large-Signal Voltage Gain 10 10 10 10 5 V/mV
VSAT Saturation Voltage VIN ≤ −5mV, IO = 25mA 1.5 1.5 1.5 1.5 1.5 V
V+ ≥ 4.5V, V− = 0V
VIN ≤ −6mV, ISINK ≤ 3.2mA
0.4 0.4 0.4 0.4 0.4 V
CMRR Common Mode Rejection
Ratio
90 90 90 90 90 dB
ISPositive Supply Current VS = ±15V 11.5 11.5 11.5 11.5 11.5 mA
Negative Supply Current VS = ±15V 4.5 4.5 4.5 4.5 4.5 mA
Output Leakage Current VIN ≥ 5mV,
VOUT to V− = 35V
22222µA
(Preirradiation) (Note 2)
RH119
3
I.D.No.66-10-0176 Rev. D
For more information www.analog.com
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
TOTAL DOSE BIAS CIRCUIT
TABLE 2: ELECTRICAL TEST REQUIREMENTS
ELECTRICAL CHARACTERISTICS
Note 1: For supply voltages less than ±15V, the maximum input voltage is
equal to the supply voltage.
Note 2: Unless otherwise noted, supply voltage equals ±15V, VCM = 0V
and TA = 25°C. The GND pin is grounded. Note that the maximum voltage
allowed between the GND pin and V+ is 18V. Do not tie the GND pin
to V– when the power supply voltage exceeds ±9V. The offset voltage,
offset current and bias current specifications apply for all supply voltages
between ±15V and 5V unless otherwise specified.
Note 3: The offset voltages and currents given are the maximum values
required to drive the output within 1V of either supply with a 1mA load––
thus, these parameters define an error band and take into account the
worst-case effects of voltage gain and input impedance.
Note 4: Response time specified for a 100mV input step with 5mV
overdrive.
Note 5: VS = ±15V, VCM = 0V, TA = 25°C unless otherwise noted.
–
+
–
+
15V
SIDE 1
SIDE 2
100Ω
10k
10k
10k
10k
GND1
GND2
OUT1
OUT2
V+
V–
–15V
RH119 TDBC
MIL-STD-883 TEST REQUIREMENTS SUBGROUP
Final Electrical Test Requirements (Method 5004) 1*, 2, 3, 4, 5, 6
Group A Test Requirements (Method 5005) 1, 2, 3, 4, 5, 6
Group B End Point Electrical Parameters (Method
5005)
1, 2, 3
*PDA Applies to subgroup 1. See PDA Test Notes.
PDA Test Notes
The PDA is specified as 5% based on failures from group A, subgroup
1, tests after cooldown as the final electrical test in accordance with
method 5004 of MIL-STD-883 Class B. The verified failures (including
Delta parameters) of group A, subgroup 1, after burn-in divided by the
total number of devices submitted for burn-in in that lot shall be used to
determine the percent for the lot.
Analog Devices reserves the right to test to tighter limits than those given.
(Continued)
REVISION HISTORY
REV DATE DESCRIPTION PAGE NUMBER
D 04/19 Obsoleting J package and updating to ADI format
RH119
4
I.D.No.66-10-0176 Rev. D
For more information www.analog.com
TYPICAL PERFORMANCE CHARACTERISTICS
Input Offset Voltage Input Bias Current Input Offset Current
Open-Loop Gain Common Mode Rejection Ratio Input Offset Voltage
TOTAL DOSE KRAD (Si)
1
INPUT OFFSET VOLTAGE (mV)
6
4
2
0
–2
–4
–6 10 100 1000
RH119 G06
VS = 15V
RS = 50Ω
TOTAL DOSE KRAD (Si)
1
INPUT OFFSET CURRENT (nA)
500
400
300
200
100
0
–100 10 100 1000
RH119 G03
VS = 15V
VCM = 0V
TOTAL DOSE KRAD (Si)
1
COMMON MODE REJECTION RATIO (dB)
150
140
130
120
110
100
90 10 100 1000
RH119 G05
VS = 15V
TOTAL DOSE KRAD (Si)
1
INPUT BIAS CURRENT (nA)
2000
1600
1200
800
400
010 100 1000
RH119 G02
VS = 15V
VCM = 0V
TOTAL DOSE KRAD (Si)
1
OPEN-LOOP GAIN (V/mV)
70
60
50
40
30
20
10 10 100 1000
RH119 G04
VS = 15V
TOTAL DOSE KRAD (Si)
1
INPUT OFFSET VOLTAGE (mV)
6
4
2
0
–2
–4
–6 10 100 1000
RH119 G01
VS = 15V
VCM = 0V
RS = 5k
04/19
ANALOG DEVICES, INC. 1990–2019
www.analog.com
