LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 1 SCOPE 0.3mm FPC This product specification covers the performance requirements for 0.3mm PITCH FPC CONNECTOR. 2 PRODUCT NAME AND PART NUMBER Product Name Part Number Housing Assembly(Right Angle Type) 504740**09 504740**09 Embossed Tape Package For 504740-**09 504740**00 ** CIRCUITS(Refer to the drawing) 3 RATINGS Item Standard Rated Voltage(MAXIMUM) 50V Rated Current (MAXIMUM) 0.3A [AC( rms)/DC] *1 Ambient Temperature Range -40C +105C Storage Condition *2*3 Temperature -10C+50C Humidity 85%R.H. 85%R.H. MAX. (No Condensation) Terms 6 For 6 months after shipped (Unopened package) 1 Non-operating connectors after reflow must follow the operating temperature range condition. 2 This includes the terminal temperature rise generated by conducting electricity. 3FPC() Applicable FPC (wires and cables) must also meet the specified temperature range. REV. A B C D SHEET 115 115 115 115 REVISE ON PC ONLY TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM REVISED J2016-0144 D 2016/08/17 YU.HASEGAWA REV. DESCRIPTION STATUS DESIGN CONTROL J DOCUMENT NUMBER PS-504740-001 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION WRITTEN BY: T.ONO CHECKED BY: APPROVED BY: H.IIJIMA Y.NOGAWA DATE: YR/MO/DAY 2013/10/31 FILE NAME SHEET PS-504740-001.docx 1 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 4 PERFORMANCE 4-1 Electrical Performance Test Condition FPC 20mV 10mA (JIS C5402-2-1) Item Contact Resistance 4-1-1 Insulation Resistance 4-1-2 Dielectric Strength 4-1-3 Mate applicable FPC, measured at the open circuit voltage 20mV MAXIMUM and short circuit 10mA MAXIMUM.(JIS C5402-2-1) Requirement 100 milliohms MAXIMUM FPC DC 125V (JIS C5402-3-1/MIL-STD-202 302) Mate applicable FPC, measured by applying DC 125V between adjacent terminal or terminal and ground. (JIS C5402-3-1/MIL-STD-202 Method 302) FPC AC125V1 (JIS C5402-4-1/MIL-STD-202 301) Mate applicable FPC, applying AC 125V effective value) between adjacent terminal or terminal and ground for 1 minutes. (JIS C5402-4-1/MIL-STD-202 Method 301) REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 50 megaohm MINIMUM No Breakdown TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 2 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 4-2 Mechanical Performance Item 4-2-1 FPC FPC Retention Force 4-2-2 Terminal Retention Force Test Condition FPC FPC253 mm Mate applicable FPC, close actuator, and pull the FPC at the speed rate of 25+ /-3 mm per minute. Apply axial pull out the each terminal assembled in the housing. Requirement 7 () Refer to paragraph 7 (Reference value) 0.2 N {0.02 kgf} MINIMUM 4-3 Environmental Performance and Others Item Durability of Actuator Operation 4-3-1 Test Condition 110 FPCFPC 10 Insert FPC, close and open actuator, withdraw FPC to 10 cycles, at the speed rate of less than 10 cycles per minute in the power-off state. Requirement Contact Resistance 120 milliohms MAXIMUM Temperature Rise 30 C MAXIMUM FPC (UL 498) Temperature Rise 4-3-2 Mate applicable FPC, measure the temperature rise of contact when the maximum AC rated current is passed.(UL 498) REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 3 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION Item 4-3-3 Vibration Mechanical Shock 4-3-4 Test Condition FPCDC1mA 3 105510 Hz/ 1.5mm 2 (JIS C 60068-2-6 /MIL-STD-202 201) Mate applicable FPC, add to each 2 hours with ratio sweep 10-55-10 Hz per minute and total amplitude 1.5 mm vibration at 3 directions mutually vertical including fitting axis in DC 1 mA electricity state. (JIS C 60068-2-6 /MIL-STD-202, Method 201) Requirement Appearance No Damage Contact Resistance 120 milliohms MAXIMUM Discontinuity 1.0 microsecond MAXIMUM Appearance No Damage Contact Resistance 120 milliohms MAXIMUM Discontinuity 1.0 microsecond MAXIMUM FPC1052 9612 (JIS C60068-2-2/MIL-STD-202 108) Appearance No Damage Mate applicable FPC, exposing for 96 hours in the atmosphere of 105+/-2 degree C. After the test, allowed to stand at room temperature for 1 to 2 hours. (JIS C60068-2-2/MIL-STD-202 Method 108) Contact Resistance 120 milliohms MAXIMUM FPCDC 1mA 6 2 490m/s {50G} 113 (JIS C60068-2-27 / MIL-STD-202 213) Mate applicable FPC, add to each 3 times with 2 impact of 490m/s {50G}on action time 11 milliseconds at 6 directions mutually vertical including fitting axis in DC 1 mA electricity state. (JIS C60068-2-27 / MIL-STD-202Method 213) Heat Resistance 4-3-5 JAPANESE ENGLISH REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 4 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION Test Condition FPC-403C 9612 ( JIS C60068-2-1 ) Item Cold Resistance 4-3-6 Mate applicable FPC and expose to -40+/-3 degree C for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours. ( JIS C60068-2-1 ) FPC602 90 95% 96 12 (JIS C60068-2-78/MIL-STD-202 103) Humidity 4-3-7 Mate applicable FPC, exposing for 96 hours in an atmosphere of 60+/-2 degree C, relative humidity 90 to 95%. After the test, allowed to stand at room temperature for 1 to 2 hours. (JIS C60068-2-78/MIL-STD-202 Method 103) FPC-55330 +10523015 5 12 (JIS C60068-2-14) Temperature Cycling 4-3-8 Mate applicable FPC, exposing to 105+/-2 degree C and -55+/-3 degree C temperature extremes for 30 minutes each including a 0-5 minutes transition time. The above-mentioned condition is repeated 5 cycles. After the test, allowed to stand at the room temperature for 1 to 2 hours before checking functionality. (JIS C60068-2-14) REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 JAPANESE ENGLISH Requirement Appearance No Damage Contact Resistance 120 milliohm MAXIMUM Appearance No Damage Contact Resistance 120 milliohm MAXIMUM Dielectric Strength 4-1-3 Must meet 4-1-3 Insulation Resistance 20 megaohm MINIMUM Appearance No Damage Contact Resistance 120 milliohm MAXIMUM TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 5 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION Item Salt Spray 4-3-9 Test Condition FPC352 51% 48 (JIS C60068-2-11/MIL-STD-202 101) Mate applicable FPC, exposing to the atmosphere where salt mist is diffused in. Other condition is written below. NaCl solution : 5+/-1% by weight Temperature : 35+/-2 degree C Duration : 48 hours After the test, they should be washed well by water and dried at room temperature before checking functionality. (JIS C60068-2-11/MIL-STD-202 Method 101) FPC402505ppm 24 SO2 Gas 4-3-10 Mate applicable FPC, exposing to the atmosphere is written below. Gas Concentration : SO2=25+/-5ppm Temperature : 40+/-2 degree C Duration : 24h REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 JAPANESE ENGLISH Requirement Appearance No Damage Contact Resistance 120 milliohm MAXIMUM Appearance No Damage Contact Resistance 120 milliohm MAXIMUM TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 6 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION Test Condition 0.2mm2455 30.5 Item Solderability 4-3-11 Dip the position of 0.2mm from terminal tip into 245 +/-5 degree C solder for 3+/-0.5 seconds. JAPANESE ENGLISH Requirement 95% 95% of immersed Solder Wetting area must show no voids, pin holes Infrared Reflow Method 5 2 Refer to the paragraph 5 2 times reflow enforcement Resistance to Soldering- Heat 4-3-12 Soldering iron method 0.2mm35010 5 Heat the position of 0.2mm from terminal tip for 5 seconds with 350+/-10 degree C soldering iron. However, without too much pressure to the terminal pin and fitting nail. Appearance No Damage Reference Standard 5 Sn-3Ag-0.5Cu The board samples of the specification test were reflowed under the reflow profile of paragraph 5. Cream soldering paste : Sn-3Ag-0.5Cu REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 7 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 5 REFLOW CONDITION 245+5/-10C Peak Temp. 245+5/-10 degree C 230C 230 degree C MINIMUM 200C 200 degree C 150C 3060 150 degree C 90120 30~60 seconds Pre-heat: 90~120 seconds TEMPERATURE CONDITION GRAPH (Temperature is measured at the soldering area on the surface of the print circuit board) N2 () NOTE: Please investigate the mounting condition (reflow soldering condition) on your own devices beforehand. The mounting conditions may change due to the soldering temperature, soldering paste, air reflow machine, Nitrogen reflow machine, and the type of printed circuit board. The different mounting conditions may have an influence on the product's performance. 6 PRODUCT SHAPE, DIMENSIONS AND MATERIALS Refer to the drawing. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 8 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 7FPC FPC RETENTION FORCE t=0.2mmFPC This test date in case of used the FPC(t=0.2mm) No of CIRCUIT UNIT 19 Retention Force (MINIMUM) st 1 10 th 10 N [kgf] 1.9 [0.19] 1.6 [0.16] 23 N [kgf] 2.3 [0.23] 2.0 [0.20] 33 N [kgf] 3.3 [0.33] 3.0 [0.30] 37 N [kgf] 3.7 [0.37] 3.4 [0.34] 39 N [kgf] 3.9 [0.39] 3.5 [0.35] 41 N [kgf] 4.1 [0.41] 3.7 [0.37] 45 N [kgf] 4.5 [0.45] 4.1 [0.41] 51 N [kgf] 5.1 [0.51] 4.7 [0.47] 61 N [kgf] 6.1 [0.71] 5.6 [0.56] FPC There may be the case which the connector performance does not meet the above specification, because the different FPC manufacturers have their own unique specification. 8 COMPLIANCE WITH ENVIRONMENTAL DIRECTIVE ELVRoHS ELV and RoHS Compliant. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 9 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION 9 JAPANESE ENGLISH INSTRUCTION UPON USAGE 1. Please do not touch the terminals before ot after reflowing the connector onto the printed circuit board. 2. FPCFPC FPC When inserting the FPC into the connector, please ensure that the actuator is completely open during insertion. Please also ensure that the FPC is completely inserted until the end of the FPC touches the housing. Diagonal insertion of the FPC into the connector can cause a short circuit due to the misaligned pitch. Diagonal insertion can also deform the terminal and/or damage the FPC contact area because the FPC edge may contact the terminal. x Diagonal insertion Straight insertion 3. When opening and closing the actuator, please do not use a sharp edged tool such as tweezers. This may cause to damage the connector or to the soldering area. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 10 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 4. -1 -2 When opening and closing the actuator, please gently pull the center of the actuator by applying an even force across the actuator and rotating carefully. (See Figure 1) Please do not apply a force only to one side of actuator because it may cause to damage the connector. (See Figure 2) Closed One-sided closing -1(Figure 1) -2(Figure 2) Not closed 5. () When closing the actuator, please press down on the actuator with soft pressure in the direction of the rotary axis as shown in the figure below. Please do not push the actuator closed from the direction that the FPC is inserted. This may cause damage or disengagement of the actuator. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 11 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 6. After the actuator is closed , please press down the surface of actuator with soft pressure in order to lock as shown in the following figure. 7. When unlocking the actuator, please pull up on the center of actuator in the direction of actuator rotation, which delivers even force to both edges of actuator. Please do not apply any force in any other direction as this may deform or damage the actuator. 8. FPC FPC When withdrawing the FPC, please make sure that the actuator is completely open. If the FPC is withdrawn without the actuator being fully open, please check to make sure that there is no debris on the contact area before inserting the FPC again. 9. FPCFPC It may cause to come off FPC, and/or occur contact defect by cabling the FPC in your application. Please make sure to avoid placing the connector where the connector is affected from the excessive force by your printed circuit board Layout reason. 10. Max0.02mm The mounting specification for coplanarity does not include the influence of warpage of the printed circuit board. The warpage of the printed circuit board should be a maximum of 0.02mm if measuring from one connector edge to the other. 11. The product performance was tested using rigid printed circuit board. In case the product needs to be reflowed onto flexible circuit board, please conduct a reflow test on the flexible circuit board in advance. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 12 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 12. Please add a stiffener on the flexible printed circuit (FPC) when you mount the connector onto FPC in order to prevent deformation of the FPC. 13. Although there might be some discoloration seen on the soldering tail after reflow, this will not influence the product's performance. 14. If you leave any soldering area on this product open, there may be the possibility of a missing terminal short circuiting between pins, terminal buckling or the potential for the connector to come off of the printed circuit board. Therefore, please solder all of the terminals and fitting nails on the printed circuit board. 15. If there is accidental contact with the connector while it is going through the reflow machine, there may be deformation or damage caused to the connector. Please check to prevent this. 16. Please do not conduct any "washing process" on the connector because it may damage the product's function. 17. FPC Please make sure to use the appropriate FPC which has Gold plating (Nickel under plating) on the contact area. 18. FPC Please check the compatibility between the connector and the FPC before mass production. 19. FPCFPC FPCFPC Please pay special attention not to add the excessive force on the FPC under the FPC inserted condition. It may cause to unlock the connector, break the FPC, and/or damage the FPC. Especially, in case the consecutive force on the FPC is added in your application, fix the FPC. Please avoid the vertical pulling force to direction of the PCB(rigid epoxy-glass printed circuit board). Also avoid twisting the FPC to the direction of contact pitch. 20. Please do not use the connector in a condition where the wire, the printed circuit board, or the contact area is experiencing a sympathetic vibration of wires and printed circuit board, and constant movement of devices. This may cause a defect in the contact due to the contact area being worn down. Therefore, please fix wires and printed circuit board on the chassis, and reduces sympathetic vibration. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 13 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 21. This product is not designed for the mating and unmating of the connectors to be performed under the condition of an active electrical circuit. It may cause a spark and product defect if the connectors are mated and unmated in this way. 22. Please keep enough clearance between connector and chassis of your application in order not to apply pressure on the connector. 23. Please do not stack the printed circuit board directly after mounted the connector on it. 24. There is no influence electrically though a few warps will be generated in the FPC insertion width of the housing. (warp of hood) 10 REPAIR 1. When conducting manual repairs using a soldering iron, please follow the soldering conditions shown in the product specification. If the conditions in the product spec are not followed, it may cause the terminals to fall off, a change in the contact gap, a deformation of the housing, melting of the housing, and damage the connector. 2. When conducting manual repairs using a soldering iron, please do not use more solder and flux than needed.This may cause solder wicking and flux wicking issues, and it will eventually cause a contact defect and functional issues. 11. EXTERNALS Although there may be some small dark spots on this product, the product performance will not be affected. There may be slight differences in the housing coloring, but there will be no influence on the product's performance. You may find the white dot on the actuator when the lubricant becomes dry, this will not affect the product's performance. REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 14 OF 15 EN-037(2015-08 rev.2) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH REV. REV. RECORD DATE ECN NO. WRITTEN BY : CHECKED BY : A RELEASED 2013/10/31 J2014-0526 T.ONO H.IIJIMA B REVISED 2014/04/15 J2014-1556 T.ONO H.IIJIMA C REVISED 2015/04/13 J2015-1144 N.ASAMUMA K.TAKAHASHI D REVISED 2015/08/18 J2016-0144 YU.HASEGAWA K.TAKAHASHI REVISE ON PC ONLY D SEE SHEET 1 OF 15 REV. DESCRIPTION DOCUMENT NUMBER PS-504740-001 TITLE: 0.3 FPC CONN BACK FLIP H=0.95MM THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX LLC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS-504740-001.docx SHEET 15 OF 15 EN-037(2015-08 rev.2)