ZS-26-F - SMC Corporation of America

How to Order

4 3 2 1

Pressure Sensor

Series PSE530

Option

PSE53 0 M5

Nil

Option

Without cable

Pressure sensing range

High pressure [0 to 1 MPa]

Vacuum [0 to –101 kPa]

Low pressure [0 to 101 kPa]

Compound pressure [–101 to 101 kPa]

Port size

M5 x 0.8

Sensor cable (3 m)

Sensor cable (3 m) + Connector (1 pc.)

Description Part no.

ZS-26-E

ZS-26-F

ZS-26-G

Note

4 pcs. per set

Cable length: 3 m

Connector

Sensor cable

Connector +

Sensor cable

Specifications

Model PSE530-M5

0 to 1 MPa

1.5 MPa

PSE531-M5

0 to –101 kPa

Air/Non-corrosive gas

12 to 24 VDC (Ripple ±10% or less)

15 mA or less

Analog output (1 to 5 V, Output impedance: Approx. 1 kΩ)

±2% F.S. or less (Within rated pressure range, Ambient temperature 25° ±3°C)

±1% F.S. or less

±1% F.S. or less based on the analog output at 18 V ranging from 12 to 24 VDC

IP40

0° to 50°C; Stored: –10° to 70°C (No freezing or condensation)

1000 VAC, 50/60Hz for 1 minute between external terminals and case

5 MΩ between external terminals and case (at 50 VDC)

10 to 500 Hz at whichever is smaller of 1.5 mm amplitude or 98 m/s

acceleration, in X, Y, Z directions, for 2 hours each (De-energized)

980 m/s2 in X, Y, Z directions, 3 times each (De-energized)

±2% F.S. or less based on the analog output value at 25°C from a range of 0° to 50°C

M5 x 0.8

Body: Stainless steel Grade 303, Internal enclosure: PPE; Pressure sensor: Silicon; O-ring: NBR

Halogen-free heavy-duty cord, ø2.7, 0.15 mm2, 3 cores, 3 m

PSE533-M5

–101 to 101 kPa

PSE532-M5

0 to 101 kPa

500kPa

Rated pressure range

Proof pressure

Fluid

Power supply voltage

Current consumption

Output specification

Accuracy

Linearity

Repeatability

Power supply voltage effect

Enclosure

Temperature range

Withstand voltage

Insulation resistance

Vibration resistance

Impact resistance

Temperature characteristics (Based on 25°C)

Port size

Material

Sensor cable/Option

Resistance

Connector



When only optional parts are required, order using the part

numbers listed below.

The connector is not connected to

the cable at the time of shipment.

Note) At the factory, the connector is not connected to the

cable, but packed together with it for shipment.

16-3-4

Internal Circuit

Dimensions

PSE53-M5

Sensor cable color

Brown

Blue

Black

DC (+) Power supply

DC (–) GND

Analog output (1 to 5 V)

With sensor cable

Main circuit

Load

Brown

Black

Blue

12 to 24 VDC

5 5.5

3.4

0.5

29.4

27.2

5.4

M5 x 0.8

Pressure port

ø2.5

ø13

ø12

ø7.2

ø2.7

ø10.4

16-3-5

ZSE

ISE

PSE

ISE3

ISE 1

ZSP

ISA2

IS

ZSM

PF2

IF

Data

Series PSE530

Pressure Sensor

1. Do not drop, bump, or apply excessive impacts (980

m/s2) while handling. Although the body of the

sensor may not be damaged, the inside of the

sensor could be damaged and lead to a

malfunction.

2. The tensile strength of the cord is 23 N. Applying a

greater pulling force on it can cause a malfunction.

When handling, hold the body of the sensor—do

not dangle it from the cord.

3. Do not exceed the screw-in torque of 3.5 N⋅m when

installing piping. Exceeding this value may cause

malfunctioning of the sensor.

4. Do not use pressure sensors with corrosive and/or

inflammable gases or liquids.

5. Connecting the sensor cable (Option)

Hold the female connector of the sensor cable with your

fingers and carefully insert it into the connector.

Warning

Handling

 Pressure Sensor

1. Do not drop, bump, or apply excessive impacts

(1000 m/s2) while handling. Although the body of

the controller case may not be damaged, the inside

of the controller could be damaged and cause a

malfunction.

2. The tensile strength of the power supply/output

connection cable is 50 N; that of the pressure

sensor lead wire with connector is 25 N. Applying a

greater pulling force than the applicable specified

tensile strength to either of these components can

lead to a malfunction. When handling, hold the

body of the controller—do not dangle it from the

cord.

Warning

Handling

1. Incorrect wiring can damage the switch and cause

a malfunction or erroneous switch output.

Connections should be done while the power is

turned off.

2. Do not attempt to insert or pull the pressure sensor

or its connector when the power is on. Switch

output may malfunction.

3. Wire separately from power lines and high voltage

lines, avoiding wiring in the same conduit with

these lines. Malfunctions may occur due to noise

from these other lines.

4. If a commercial switching regulator is used, make

sure that the F.G. terminal is grounded.

Connection

Warning

1. Our multi-channel pressure sensor controllers are

CE marked; however, they are not equipped with

surge protection against lightning. Lightning surge

countermeasures should be applied directly to

system components as necessary.

2. Our multi-channel pressure sensor controllers do

not have an explosion proof rating. Never use

pressure sensors in the presence of inflammable or

explosive gases.

3. Enclosure “IP65” applies only to the front face of

the panel when mounting. Do not use in an

environment where oil splashing or spraying are

anticipated.

Operating Environment

Warning

1. The pressure sensors are CE marked; however, they

are not equipped with surge protection against

lightning. Lightning surge countermeasures should

be applied directly to system components as

necessary.

2. The pressure sensors do not have an explosion

proof rating. Never use pressure sensors in the

presence of inflammable or explosive gases.

Operating Environment

Warning

 Controller

Sensor

Male connector

Female connector

Unlock

Lock

Sensor

Connector cover

A connector cover is provided as part of the cable assembly

(see the figure below). It is designed to keep the female

connector from slipping out of the sensor. To lock the connector

cover in place, first make sure it is facing in the right direction

as you slip it over the female connector, then lock it to the

sensor body by turning it clockwise. To remove the cover, first

unlock it by turning it counterclockwise, then pull back on it. To

remove the female connector, grab it with your fingers and pull

back on it. Do not pull on the cable.

Series PSE

Specific Product Precautions 1

Be sure to read before handling.

16-3-19

ZSE

ISE

PSE

ISE3

ISE 1

ZSP

ISA2

IS

ZSM

PF2

IF

Data

Mounting Wiring

Tighten screws 1/4 to 1/2 turn after the heads are flush with the panel.

Standard

When using 48 conversion adapter

48 conversion adapter

(ZS-26-D)

2-M3 x 8L

Front protective cover

(ZS-26-01) Panel mount

(ZS-26-B)

Caution

The front face of the panel mount conforms to IP65

(IP40 when using the 48 conversion adapter);

however, there is a possibility of liquid filtration if the

panel mount adapter is not installed securely and

properly. Securely fix the adaptor with screws as

shown below.

1. Connecting sensor cable and connector (ZS-26-E)

• Cut the sensor cable as shown below.

• Insert each lead wire into the corresponding connector number

by following the chart provided below.

Core wire color

of sensor cable

Brown (DC+)

Black (Analog output)

Blue (DC–)

N.C.

Connector

no.

Power supply/Output connector

Sensor connector port

4321

20 mm or more

4 3 2 1



4 3 2 1

2 m

Caution

• Make sure that the number of connector and the core wire

color match. After verifying that the wires are inserted all the

way, temporarily hold the connector down manually.

• Using pliers, snap A into B as shown below so that there is no

gap between A and B, and secure the connector.

• The A and B portion of the sensor connector are already tacked

down temporarily at the time of shipment. Do not snap the A

portion in place before inserting the cable. Note that the

connector cannot be taken apart to be reused once it is

crimped. Use a new sensor connector in case wiring or the

snapping of A into B are done incorrectly.

• To connect the connector to the multi-channel pressure sensor,

push the connector with its A portion facing toward you into the

socket until it clicks as shown below.

• To remove the connector, pull it straight out while applying

pressure to the fingers on both sides.

2. Connecting power supply/output connection cable

• To connect the power supply/output connection cable to the

controller, insert the cable connector with the C part facing

down until it clicks.

Brown

Black

Blue

N.C.

Ver ify from the top side of

A that the lead wires are

inserted completely.

Series PSE

Specific Product Precautions 2

Be sure to read before handling.

16-3-20

Wiring

Caution

3. Connecting to other series

• Any pressure sensor (SW) can be connected as long as it

generates analog output (1 to 5 V) signal. However, the

pressure range must match.

• SMC pressure sensors, Series PSE510 & PSE520, are also

connectable.

• When connecting to pressure sensors other than the Series

PSE530, connector types will vary depending on the wire core

size of the cable and the outside diameter of the insulation

cover. Refer to the table provided below.

• Refer to the following diagram for connecting Series PSE520 to

the connector.

ZS-26-E

ZS-26-E-1

ZS-26-E-2

ZS-26-E-3

Connector

part no. Wire core size

AWG24-26 (0.14 to 0.2 mm2)

AWG20-22 (0.3 to 0.5 mm2)

Insulation

cover

O.D.

ø1.0 to 1.4

ø1.4 to 2.0

ø1.0 to 1.4

ø1.4 to 2.0

Sensor part no.

PSE510, PSE530

PSE521

PSE520

Brown

Black

Blue

N.C.

F. G .

Regulating Pressure Range & Rated Pressure Range

1. Regulating pressure range: Refers to allowable

pressure range in a pressure setting mode.

• Setting range is between P_1(n_1) to P_4(n_4).

• For Series PSE200, the regulating pressure range and the

setting pressure range that can be displayed are the same.

2. Rated pressure range: Refers to the pressure range

that satisfies the product specifications.

• Pressure range that satisfies the product specifications

(accuracy and linearity) for PSE530.

Caution

( )

There is no shielding wire for

Series PSE510 & PSE530.

Connect the shielding wire to

the frame ground (F.G.) or

F.G. terminal.

Series PSE

Specific Product Precautions 3

Be sure to read before handling.

16-3-21

ZSE

ISE

PSE

ISE3

ISE 1

ZSP

ISA2

IS

ZSM

PF2

IF

Data

Safety Instructions

These safety instructions are intended to prevent a hazardous situation and/or

equipment damage. These instructions indicate the level of potential hazard by labels of

"Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1),

JIS B 8370

Note 2) and other safety practices.

1. The compatibility of pneumatic equipment is the responsibility of the person

who designs the pneumatic system or decides its specifications.

Since the products specified here are used in various operating conditions, their compatibility for the

specific pneumatic system must be based on specifications or after analysis and/or tests to meet your

specific requirements. The expected performance and safety assurance will be the responsibility of the

person who has determined the compatibility of the system. This person should continuously review

the suitability of all items specified, referring to the latest catalog information with a view to giving due

consideration to any possibility of equipment failure when configuring a system.

2. Only trained personnel should operate pneumatically operated machinery

and equipment.

Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of

pneumatic systems should be performed by trained and experienced operators.

3. Do not service machinery/equipment or attempt to remove components until

safety is confirmed.

1. Inspection and maintenance of machinery/equipment should only be performed once measures to

prevent falling or runaway of the driver objects have been confirmed.

2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply

pressure for this equipment and exhaust all residual compressed air in the system.

3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston

rod, etc.

4. Contact SMC if the product is to be used in any of the following conditions:

1. Conditions and environments beyond the given specifications, or if product is used outdoors.

2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles,

medical equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and

brake circuits in press applications, or safety equipment.

3. An application which has the possibility of having negative effects on people, property, or animals,

requiring special safety analysis.

Note 1) ISO 4414: Pneumatic fluid power--General rules relating to systems.

Note 2) JIS B 8370: General Rules for Pneumatic Equipment

Warning

Caution : Operator error could result in injury or equipment damage.

Warning

: Operator error could result in serious injury or loss of life.

Danger : In extreme conditions, there is a possible result of serious injury or loss of life.

16-14-3

1. Confirm the specifications.

Products represented in this catalog are designed for use in

compressed air appllications only (including vacuum), unless

otherwise indicated.

Do not use the product outside their design parameters.

Please contact SMC when using the products in applications

other than compressed air (including vacuum).

4. Use clean air

If the compressed air supply is contaminated with chemicals,

cynthetic materials, corrosive gas, etc., it may lead to break

down or malfunction.

Selection

Mounting

Piping

Air Supply

Maintenance

Operating Environment

Warning

1. Instruction manual

Install the products and operate them only after reading the

instruction manual carefully and understanding its contents.

Also keep the manual where it can be referred to as

necessary.

2. Securing the space for maintenance

When installing the products, please allow access for

maintenance.

3. Tightening torque

When installing the products, please follow the listed torque

specifications.

Warning

1. Do not use in environments where the product

is directly exposed to corrosive gases,

chemicals, salt water, water or steam.

2. Do not expose the product to direct sunlight

for an extended period of time.

3. Do not use in a place subject to heavy

vibrations and/or shocks.

4. Do not mount the product in locations where it

is exposed to radiant heat.

Warning

1. Maintenance procedures are outlined in the

operation manual.

Not following proper procedures could cause the product to

malfunction and could lead to damage to the equipment or

machine.

2. Maintenance work

If handled improperly, compressed air can be dangerous.

Assembly, handling and repair of pneumatic systems should

be performed by qualified personnel only.

3. Drain flushing

Remove drainage from air filters regularly. (Refer to the

specifications.)

4. Shut-down before maintenance

Before attempting any kind of maintenance make sure the

supply pressure is shut of and all residual air pressure is

released from the system to be worked on.

5. Start-up after maintenance and inspection

Apply operating pressure and power to the equipment and

check for proper operation and possible air leaks. If operation

is abnormal, please verify product set-up parameters.

6. Do not make any modifications to be product.

Do not take the product apart.

Warning

1. Before piping

Make sure that all debris, cutting oil, dust, etc, are removed

from the piping.

2. Wrapping of pipe tape

When screwing piping or fittings into ports, ensure that chips

from the pipe threads or sealing material do not get inside the

piping. Also, when the pipe tape is used, leave 1.5 to 2 thread

ridges exposed at the end of the threads.

Caution

1. Operating fluid

Please consult with SMC when using the product in

applications other than compressed air (including vacuum).

Regarding products for general fluid, please ask SMC about

applicable fluids.

2. Install an air dryer, aftercooler, etc.

Excessive condensate in a compressed air system may cause

valves and other pneumatic equipment to malfunction.

Installation of an air dryer, after cooler etc. is recommended.

3. Drain flushing

If condensate in the drain bowl is not emptied on a regular

basis, the bowl will over flow and allow the condensate to

enter the compressed air lines.

If the drain bowl is difficult to check and remove, it is

recommended that a drain bowl with the auto-drain option be

installed.

For compressed air quality, refer to “Air Preparation

Equipment” catalog.

Warning

Common Precautions

Be sure to read before handling.

For detailed precautions on every series, refer to main text.

16-14-4

Quality Assurance Information

(ISO 9001, ISO 14001)

Reliable quality of products in the global market

To enable our customers throughout

the world to use our products with

even greater confidence, SMC has

obtained certification for international

standards “ISO 9001” and “ISO

14001”, and created a complete

structure for quality assurance and

environmental controls. SMC

products pursue to meet its

customers’ expectations while also

considering company’s contribution in

society.

This is an international standard for quality control

and quality assurance. SMC has obtained a large

number of certifications in Japan and overseas,

providing assurance to our customers throughout

the world.

Quality management system

ISO 9001

This is an international standard related to

environmental management systems and

environmental inspections. While promoting

environmentally friendly automation technology,

SMC is also making diligent efforts to preserve

the environment.

Environmental management system

ISO 14001

Sales coordination

Production

Make customers our

first priority, offering

them reliable and

friendly service.

Market research

Product planning

After service

Process control

Inspection, testing, etc.

Initial production control

Quality system

education

Training of

suppliers

New product evaluation

Reliability design

Reliability testing

New technical

development

Education

Training

Research

Design

Development

Produce the highest

quality with the

participation of all

employees.

Create new

products using the

latest technology,

and offer the finest

products in a

timely manner.

SMC’s quality control system

Quality policies

Quality control activities

16-14-5

CE Mark

SMC Product Conforming to Inter

SMC products complying with EN/ISO, CSA/UL standards are supporting

The CE mark indicates that machines and components meet essential requirements of all the EC Directives

applied.

It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and

components are exported to the member Nations of the EU.

Once “A manufacturer himself” declares a product to be safe by means of CE marking (declaration of

conformity by manufacturer), free distribution inside the member Nations of the EU is permissible.

 CE Mark

SMC provides CE marking to products to which EMC and Low Voltage Directives have been applied, in

accordance with CETOP (European hydraulics and pneumatics committee) guide lines.

 As of February 1998, the following 18 countries will be obliged to conform to CE mark legislation

Iceland, Ireland, United Kingdom, Italy, Austria, Netherlands, Greece, Liechtenstein, Sweden, Spain, Denmark,

Germany, Norway, Finland, France, Belgium, Portugal, Luxembourg

 EC Directives and Pneumatic Components

• Machinery Directive

The Machinery Directive contains essential health and safety requirements for machinery, as applied to

industrial machines e.g. machine tools, injection molding machines and automatic machines. Pneumatic

equipment is not specified in Machinery Directive. However, the use of SMC products that are certified as

conforming to EN Standards, allows customers to simplify preparation work of the Technical Construction File

required for a Declaration of Conformity.

• Electromagnetic Compatibility (EMC) Directive

The EMC Directive specifies electromagnetic compatibility. Equipment which may generate electromagnetic

interference or whose function may be compromised by electromagnetic interference is required to be immune

to electromagnetic affects (EMS/immunity) without emitting excessive electromagnetic affects (EMI/emission).

• Low Voltage Directive

This directive is applied to products, which operate above 50 VAC to 1000 VAC and 75 VDC to 1500 VDC

operating voltage, and require electrical safety measures to be introduced.

• Simple Pressure Vessels Directive

This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V)

exceed 50 bar/L. Such vessels require EC type examination and then CE marking.

16-14-6

http://www.smcworld.com

you to comply with EC directives and CSA/UL standards.

 CSA Standards & UL Standards

UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric

products, and are defined to mainly prevent danger from electric shock or fire, resulting from trouble with

electric products. Both UL and CSA standards are acknowledged in North America as the first class certifying

body. They have a long experience and ability for issuing product safety certificate. Products approved by CSA

or UL standards are accepted in most states and governments beyond question.

Since CSA is a test certifying body as the National Recognized Testing Laboratory (NRTL) within the

jurisdiction of Occupational Safety and Health Administration (OSHA), SMC was tested for compliance with

CSA Standards and UL Standards at the same time and was approved for compliance with the two Standards.

The above CSA NRTL/C logo is described on a product label in order to indicate that the product is approved

by CSA and UL Standards.

 TSSA (MCCR) Registration Products

TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi

(0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation.

Products conforming to CE Standard

With CE symbol for simple visual recognition

In this catalog each accredited product series is indicated with a

CE mark symbol. However, in some cases, every available

models may not meet CE compliance. Please visit our web site

for the latest selection of available models with CE mark.

Mark of compliance

for CSA

Mark of compliance

for CSA/UL

national Standards

16-14-7

SMC Product Conforming to International Standards

America Europe

U.S.A. SMC Corporation of America

3011 North Franklin Road Indianapolis, IN 46226, U.S.A.

TEL: 317-899-4440 FAX: 317-899-3102

CANADA SMC Pneumatics (Canada) Ltd.

6768 Financial Drive Mississauga, Ontario, L5N 7J6 Canada

TEL: 905-812-0400 FAX: 905-812-8686

MEXICO SMC Corporation (Mexico), S.A. DE C.V.

Carr. Silao-Trejo K.M. 2.5 S/N, Predio San Jose del Duranzo

C.P. 36100, Silao, Gto., Mexico

TEL: 472-72-2-55-00 FAX: 472-72-2-59-44/2-59-46

CHILE SMC Pneumatics (Chile) S.A.

Av. La Montaña 1,115 km. 16,5 P. Norte Parque

Industrial Valle Grande, Lampa Santiago, Chile

TEL: 02-270-8600 FAX: 02-270-8601

ARGENTINA SMC Argentina S.A.

Teodoro Garcia 3860 (1427) Buenos Aires, Argentina

TEL: 011-4555-5762 FAX: 011-4555-5762

BOLIVIA SMC Pneumatics Bolivia S.R.L.

Avenida Beni Numero 4665

Santa Cruz de la Sierra-Casilla de Correo 2281, Bolivia

TEL: 591-3-3428383 FAX: 591-3-3449900

VENEZUELA SMC Neumatica Venezuela S.A.

Apartado 40152, Avenida Nueva Granada, Edificio Wanlac,

Local 5, Caracas 1040-A, Venezuela

TEL: 2-632-1310 FAX: 2-632-3871

PERU (Distributor) IMPECO Automatizacion Industrial S.A.

AV. Canevaro 752, Lince, Lima, Peru

TEL: 1-471-6002 FAX: 1-471-0935

URUGUAY (Distributor) BAKO S.A.

Galicia 1650 esq. Gaboto C.P. 11200, Montevideo, Uruguay

TEL: 2-401-6603 FAX: 2-409-4306

BRAZIL SMC Pneumaticos Do Brasil Ltda.

Rua. Dra. Maria Fidelis, nr. 130, Jardim Piraporinha-Diadema-S.P.

CEP: 09950-350, Brasil

TEL: 11-4051-1177 FAX: 11-4071-6636

COLOMBIA (Distributor) Airmatic Ltda.

Calle 18 69-05 Apart. Aereo 081045 Santa Fe de Bogotá, Colombia

TEL: 1-424-9240 FAX: 1-424-9260

U.K. SMC Pneumatics (U.K.) Ltd.

Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN, Backinghamshire, U.K.

TEL: 01908-563888 FAX: 01908-561185

GERMANY SMC Pneumatik GmbH

Boschring 13-15 D-63329 Egelsbach, Germany

TEL: 06103-4020 FAX: 06103-402139

ITALY SMC Italia S.p.A.

Via Garibaldi 62 I-20061 Carugate Milano, Italy

TEL: 02-9271365 FAX: 02-9271365

FRANCE SMC Pneumatique S.A.

1 Boulevard de Strasbourg, Parc Gustave Eiffel, Bussy Saint Georges, F-77600

Marne La Vallee Cedex 3 France

TEL: 01-64-76-10-00 FAX: 01-64-76-10-10

SWEDEN SMC Pneumatics Sweden AB

Ekhagsvägen 29-31, S-141 05 Huddinge, Sweden

TEL: 08-603-07-00 FAX: 08-603-07-10

SWITZERLAND SMC Pneumatik AG

Dorfstrasse 7, Postfach 117, CH-8484 Weisslingen, Switzerland

TEL: 052-396-3131 FAX: 052-396-3191

AUSTRIA SMC Pneumatik GmbH (Austria)

Girakstrasse 8, A-2100 Korneuburg, Austria

TEL: 0-2262-6228-0 FAX: 0-2262-62285

SPAIN SMC España, S.A.

Zuazobidea 14 Pol. Ind. Júndiz 01015 Vitoria, Spain

TEL: 945-184-100 FAX: 945-184-510

IRELAND SMC Pneumatics (Ireland) Ltd.

2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin, Ireland

TEL: 01-403-9000 FAX: 01-466-0385

NETHERLANDS (Associated company) SMC Pneumatics BV

De Ruyterkade 120, NL-1011 AB Amsterdam, Netherlands

TEL: 020-5318888 FAX: 020-5318880

GREECE (Distributor) S.Parianopoulos S.A.

7, Konstantinoupoleos Street 11855 Athens, Greece

TEL: 01-3426076 FAX: 01-3455578

DENMARK SMC Pneumatik A/S

Knudsminde 4 B DK-8300

Odder, Denmark

TEL: 70252900 FAX: 70252901

SMC’s Global Service Network

16-14-20

Europe

FINLAND SMC Pneumatics Finland OY

PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland

TEL: 09-8595-80 FAX: 09-8595-8595

NORWAY SMC Pneumatics Norway A/S

Vollsveien 13C, Granfoss Næringspark N-1366 LYSAKER, Norway

TEL: 67-12-90-20 FAX: 67-12-90-21

BELGIUM (Distributor) SMC Pneumatics N.V./S.A.

Nijverheidsstraat 20 B-2160 Wommelgem Belguim

TEL: 03-355-1464 FAX: 03-355-1466

POLAND SMC Industrial Automation Polska Sp.z.o.o.

ul. Konstruktorska 11A, PL-02-673 Warszawa, Poland

TEL: 022-548-5085 FAX: 022-548-5087

TURKEY (Distributor) Entek Pnömatik San.ve Tic. Ltd. Sti

Perpa Tic. Merkezi Kat:11 No.1625 80270 Okmeydani Istanbul, Türkiye

TEL: 0212-221-1512 FAX: 0212-221-1519

RUSSIA SMC Pneumatik LLC.

36/40 Sredny prospect V.O. St. Petersburg 199004, Russia

TEL: 812-118-5445 FAX: 812-118-5449

CZECH SMC Industrial Automation CZ s.r.o.

Hudcova 78a, CZ-61200 Brno, Czech Republic

TEL: 05-4121-8034 FAX: 05-4121-8034

HUNGARY SMC Hungary Ipari Automatizálási kft.

Budafoki ut 107-113 1117 Budapest

TEL: 01-371-1343 FAX: 01-371-1344

ROMANIA SMC Romania S.r.l.

Str. Frunzei, Nr. 29, Sector 2, Bucharest, Romania

TEL: 01-3205111 FAX: 01-3261489

SLOVAKIA SMC Priemyselná automatizáciá, s.r.o

Nova 3, SK-83103 Bratislava

TEL: 02-4445-6725 FAX: 02-4445-6028

SLOVENIA SMC Industrijska Avtomatilca d.o.o.

Grajski trg 15, SLO- 8360 Zuzemberk, Slovenia

TEL: 07388-5240 FAX: 07388-5249

SOUTH AFRICA (Distributor) Hyflo Southern Africa (Pty.) Ltd.

P.O.Box 240 Paardeneiland 7420 South Africa

TEL: 021-511-7021 FAX: 021-511-4456

EGYPT (Distributor) Saadani Trading & Ind. Services

15 Sebaai Street, Miami 21411 Alexandria, Egypt

TEL: 3-548-50-34 FAX: 3-548-50-34

Oceania/Asia

AUSTRALIA SMC Pneumatics (Australia) Pty.Ltd.

14-18 Hudson Avenue Castle Hill NSW 2154, Australia

TEL: 02-9354-8222 FAX: 02-9894-5719

NEW ZEALAND SMC Pneumatics (New Zealand) Ltd.

8C Sylvia Park Road Mt.Wellington Auckland, New Zealand

TEL: 09-573-7007 FAX: 09-573-7002

TAIWAN SMC Pneumatics (Taiwan) Co.,Ltd.

17, Lane 205, Nansan Rd., Sec.2, Luzhu-Hsiang, Taoyuan-Hsien, TAIWAN

TEL: 03-322-3443 FAX: 03-322-3387

HONG KONG SMC Pneumatics (Hong Kong) Ltd.

29/F, Clifford Centre, 778-784 Cheung, Sha Wan Road, Lai Chi Kok, Kowloon,

Hong Kong

TEL: 2744-0121 FAX: 2785-1314

SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.

89 Tuas Avenue 1, Jurong Singapore 639520

TEL: 6861-0888 FAX: 6861-1889

PHILIPPINES SHOKETSU SMC Corporation

Unit 201 Common Goal Tower, Madrigal Business Park,

Ayala Alabang Muntinlupa, Philippines

TEL: 02-8090565 FAX: 02-8090586

MALAYSIA SMC Pneumatics (S.E.A.) Sdn. Bhd.

Lot 36 Jalan Delima1/1, Subang Hi-Tech Industrial Park, Batu 3 40000 Shah Alam

Selangor, Malaysia

TEL: 03-56350590 FAX: 03-56350602

SOUTH KOREA SMC Pneumatics Korea Co., Ltd.

Woolim e-BIZ Center (Room 1008), 170-5, Guro-Dong, Guro-Gu,

Seoul, 152-050, South Korea

TEL: 02-3219-0700 FAX: 02-3219-0702

CHINA SMC (China) Co., Ltd.

7 Wan Yuan St. Beijing Economic & Technological Development Zone 100176, China

TEL: 010-67882111 FAX: 010-67881837

THAILAND SMC Thailand Ltd.

134/6 Moo 5, Tiwanon Road, Bangkadi, Amphur Muang, Patumthani 12000, Thailand

TEL: 02-963-7099 FAX: 02-501-2937

INDIA SMC Pneumatics (India) Pvt. Ltd.

D-107 to 112, Phase-2, Extension, Noida, Dist. Gautaim Budh Nagar,

U.P. 201 305, India

TEL: (0120)-4568730 FAX: 0120-4568933

INDONESIA (Distributor) P.T. Riyadi Putera Makmur

Jalan Hayam Wuruk Komplek Glodok Jaya No. 27-28 Jakarta 11180 Indonesia

TEL: 021-625 5548 FAX: 021-625 5888

PAKISTAN (Distributor) Jubilee Corporation

First Floor Mercantile Centre, Newton Road Near Boulton Market P.O. Box 6165

Karachi 74000 Pakistan

TEL: 021-243-9070/8449 FAX: 021-241-4589

ISRAEL (Distributor) Baccara Automation Control

Kvutzat Geva 18915 Israel

TEL: 04-653-5960 FAX: 04-653-1445

SAUDI ARABIA (Distributor) Assaggaff Trading Est.

P.O. Box 3385 Al-Amir Majed Street, Jeddah-21471, Saudi Arabia

TEL: 02-6761574 FAX: 02-6708173

16-14-21

SMC’s Global Service Network