REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Sheet 4: TABLE I. Input offset voltage test. Device type 01. For subgroup 2,
delete the min limit of “1.5 mV” and substitute “5 mV”. Input bias current test.
Device type 01. For subgroup 2, delete the min limit of “40 nA” and substitute
“60 nA”. Input offset current test. Device type 01. For subgroup 2, delete the
min limit of “12 nA” and substitute “20 nA”.
Sheet 5: TABLE I. Common mode rejection ratio test. Device type 01.
For subgroup 2, delete the min limit of “86 dB” and substitute “82 dB”;
Power supply rejection ratio test. Device type 01. For subgroup 2, delete the
min limit of “86 dB” and substitute “82 dB”.
Changes in accordance with notice of revision 5962-R012-96. - ro
96-01-30 M. A. FRYE
B Drawing updated to reflect current requirements.
Incorporate N.O.R. 5962-R012-96. Redrawn. - ro 05-03-09 R. MONNIN
C Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-04-19 C. SAFFLE
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS REV C C C C C C C C C C
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10
PMIC N/A PREPARED BY
RICK OFFICER
DLA LAND AND MARITIME
COLUMBUS, OHIO 4321 8-3990
http://www.dscc.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
RAY MONNIN
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, DUAL COMPARATOR,
MONOLITHIC SILICON
DRAWING APPROVAL DATE
89-05-02
AMSC N/A
REVISION LEVEL
C SIZE
A CAGE CODE
67268
5962-89504
SHEET 1 OF 10
DSCC FORM 2233
APR 97 5962-E159-11
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device r equirements for MIL-STD-883 compliant, non-JAN class lev el B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-89504 01 G A
Drawing number Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function IIB ( TA = 25C )
01 LT1017 Dual comparator 15 nA
02 LT1018 Dual comparator 75 nA
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as fol lows:
Outline letter Descriptive designator Terminals Package style
G MACY1-X8 8 Can
P GDIP1-T8 or CDIP2-T8 8 Dual-in-line
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, app endix A.
1.3 Absolute maximum ratings.
Positive supply voltage (V+) ........................................................................... +40 V dc
Negative supply voltage (V-) ........................................................................... -40 V dc
Input voltage range ......................................................................................... -0.3 V dc to +40 V dc
Differential input voltage (VIN) ........................................................................ 40 V dc
Output short circuit duration ............................................................................ Indefinite
Storage temperature range ............................................................................. -65C to +150C
Power dissipation (PD) ................................................................................... 1.0 W
Lead temperature (soldering, 10 seconds) ..................................................... +300C
Junction temperature (TJ) ............................................................................... +150 C
Thermal resistance, junction-to-case (JC) ..................................................... See MIL-STD-1835
Thermal resistance, junction-to-ambient (JA) ................................................ 150C/W
1.4 Recommended operating conditions.
Ambient operating temperature range (TA) .................................................... -55C to +125C
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and han dbooks. The following specification, standards, an d handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Sp ecification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents ar e available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue , Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unle ss a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for
non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified
Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional
certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program
plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality
Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or
function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and ph ysical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics . Unless otherwise specified herein, the electrical performance character istics are
as specified in table I and shall app ly over the full ambient operating temperature ran ge.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in tabl e I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi c s.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Input offset voltage 1/ VIO 0.75 V VS 20 V 1 All 1.0 mV
2 01 5.0
02 1.5
3 All 1.4
Input bias current IIB 0.75 V VS 20 V 1 01 15 nA
02 75
2 01 60
02 110
3 01 25
02 100
Input offset current IIO 0.75 V VS 20 V 1 01 2.0 nA
02 8.0
2 01 20
02 20
3 01 3.0
02 12
Common mode rejection
mode CMRR VS = 20 V, 1 All 105 dB
-20 V VCM 19.1 V 2 01 82
02 86
3 All 100
Power supply rejection
ration PSRR +0.75 V V+ +20 V, 1 All 96 dB
-20 V V- -0.75 V 2 01 82
02 86
3 All 95
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi c s – Continued.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Gain G
No load, VOUT = 19.9 V, 1 All 110 dB
V+ = +20 V dc, 2 100
V- = -20 V dc 2/ 3 105
RL = 4.0 k,
VOUT = 19 V,
1 100
V+ = +20 V dc, 3 94
V- = -20 V dc
Output sink current IO(SK) V+ = 4.5 V, V- = 0 V, 1 01 30 mA
overdrive 30 mV, 02 35
VOUT = 2.0 V 2 All 10
3 25
Output source current IO(SO) V+ = 40 V, V- = 0 V, 1 01 30 A
VIN = 5.0 mV, 02 75
VOUT 0.4 V 2 01 25
02 50
3 01 25
02 50
V+ = 1.2 V, V- = 0 V, 1 01 25
VIN = 5.0 mV, 02 70
VOUT 0.4 V 2 01 25
02 40
3 01 15
02 45
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi c s – Continued.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Positive output
saturation voltage +VO(SAT) I
OUT = 0 A, 1 All 80 mV
V+ = 1.2 V, V- = 0 V 2 100
3 90
IOUT = 10 A, 1 250
V+ = 1.2 V, V- = 0 V 2,3 300
Negative output
saturation voltage -VO(SAT) I
OUT = 0 mA, 1 01 20 mV
V+ = 4.5 V, V- = 0 V, 02 15
VIN = -10 V 2 01 50
02 40
3 All 20
IOUT = 0.1 mA, 1 All 60
V+ = 4.5 V, V- = 0 V, 2 100
VIN = -10 V 3 01 75
02 70
IOUT = 1.0 mA, 1 All 120
V+ = 4.5 V, V- = 0 V, 2 200
VIN = -10 V 3 150
IOUT = 10 mA, 1 01 200
V+ = 4.5 V, V- = 0 V, 02 250
VIN = -10 V 2 01 600
02 400
3 All 300
IOUT = 30 mA, 1 01 600
V+ = 4.5 V, V- = 0 V, 02 700
VIN = -10 V 3 All 900
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 7
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi c s – Continued.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Leakage current IL V
OUT = 40 V, 1 01 3.0
A
VIN 100 mV, 02 8.0
V+ = 5.0 V, V- = 0 V 2 01 5.0
02 15
3 01 3.0
02 10
Supply current IS V+ = 5.0 V, V- = 0 V 1 01 60 A
02 250
2 01 80
02 300
3 01 80
02 250
V+ = +40 V, V- = 0 V 1 01 90
02 250
2 01 100
02 300
3 01 100
02 270
Minimum operating
voltage VOP I
OUT = 1.0 mA 1,2,3 01 1.15 V
02 1.2
1/ Input offset voltage is guaranteed over a common mode voltage range of V- VIN (V+ -0.9 V).
2/ No load gain is guaranteed but not tested, (device type 01 only).
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 8
DSCC FORM 2234
APR 97
Device types All
Case outlines G and P
Terminal number Terminal symbol
1 Output A
2 -Input A
3 +Input A
4 V-
5 +Input B
6 -Input B
7 Output B
8 V+
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 9
DSCC FORM 2234
APR 97
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of complian ce submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as require d in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits deliver ed to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the optio n of the reviewer.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection pro c edures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devi c es
prior to quality conformance inspection. The following additional criteri a shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspectio n . Quality conformance inspection shall be in accordance with method 5005 of
MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 4, 5, 6, 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state lif e test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be ma de available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicabl e, in accordanc e wit h the inte nt specified in
method 1005 of MIL-STD-883.
(2) TA = +125C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-89504
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 10
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgr oups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004) ---
Final electrical test parameters
(method 5004) 1*,2,3
Group A test requirements
(method 5005) 1,2,3
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
5. PACKAGING
5.1 Packaging requirements. The requir ements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming t o this drawing are intended for use for Government microcircuit application s
(original equipment), desig n applications, and logistics purposes.
6.2 Replaceability. Microcirc uits covered by this drawing will replace the same generic d evice covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed chan ges to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished usin g DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of cha nges to the drawings. Users of drawings covering microelectronics
devices (FSC 5962) should c ontact DLA Land and Maritime -VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio
43218-3990, or telephone (614) 692-0540.
6.6 Approved sources of supply. Approved sources of suppl y are listed in MIL-HDBK-10 3. The vendors listed in
MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and
accepted by DLA Land and Maritime -VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 11-04-19
Approved sources of suppl y for SMD 5962-89504 are listed below for immediate acq uisition information only a nd
shall be added to MIL-HDBK-103 an d QML-38535 during the ne xt revision. MIL-HDBK-103 and QML-38 535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been subm itted to and accepted by DLA Land and Maritim e -VA. T his information
bulletin is superseded by the ne xt dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8950401GA 60264 MTLT1017QH
3/ LT1017MH/883
5962-8950401GC 60264 MTL1017MH/883
5962-8950401PA 60264 MTLT1017QD8
60264 MTL1017MJ8/883
64155 LT1017MJ8/883
5962-8950401PC 60264 MTL1017MD8/883
60264 MTL1017MJ8/883
5962-8950402GA 60264 MTLT1018QH
3/ LT1018MH/883
5962-8950402GC 60264 MTL1018MH/883
5962-8950402PA 60264 MTLT1018QD8
60264 MTL1018MJ8/883
64155 LT1018MJ8/883
5962-8950402PC 60264 MTL1018MD8/883
60264 MTL1018MJ8/883
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number m ay not
satisfy the performance requirements of this drawing.
3/ Not available from an approve d source of su pply.
1 of 2
STANDARD MICROCIRCUIT DRAWING BULLETIN - CONTINUED.
DATE: 11-04-19
Vendor CAGE Vendor name
number and address
60264 Minco Technology La bs, Inc.
1805 Rutherford Lane
Austin, TX 78754-5101
64155 Linear Technology Corporation
1630 McCarthy Blvd.
Milpitas, CA 95035-7417
2 of 2
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoeve r for any inaccuracies in the
information bulletin.
