REVISIONS
LTR
DESCRIPTION
DATE
APPROVED
A Changes in ac c ordance with NOR 5998-R005-95 28 June 1996 John F. Raye
B Add new configurations D and E. Change FSC from 5999 to 5998.
Editorial changes througho ut. 22 May 2000 Monica L. Poelk i ng
C Corrected inaccuracies in al l c onfigurations. 7 SEP 2001 Thomas M. Hes s
D Section 2 updated to remove c ancelled docu ments and add the
superseding replacements. C orrected super s ession data. Added an
additional supplier. Editor ial changes thr oughout.
20 SEP 2002 Thomas M. Hess
E Corrected inaccuracies in configurations D, E , F, G, and H. Editorial
changes thro ughout. 24 OCT 2003 Thomas M. Hess
F Corrected inaccuracies in configurations A, B, C, and D. 6 JUN 2014 Thomas M . Hess
G Update material requirements for alignment springs. 24 OCT 2016 Thomas M. Hess
Prepared in accordance with ASME Y14.100
REV G G G G G G G
PAGE 16 17 18 19 20 21 22 23 24 25 26
REV STATUS
OF PAGES
REV G G G G G G G G G G G G G G G
PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PMIC N/A
PREPARED BY DESIGN ACTIVITY
DEFENSE ELECTRONICS SUPPLY CE NTER,
DAYTON, OH 454 44 –5000
Bernard J. Miesse
Original date of drawing
8 November 1989
CHECKED BY TITLE
David J. Corbett
HOLDER, ELECT RICAL CARD, WEDGE
RETAINER, 5 PIECE, .225 INCH BY .225 INCH
AND .225 INCH BY .2 60 INCH BODY SIZE
APPROVED BY
Monica L. Poelking
SIZE
CAGE CODE
DWG. NO. 89064
A
14933
REV G PAGE 1 OF 26
AMSC N/A 5998–2016–E086
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME,
COLUMBUS, OHIO 43218–3990
Notice of Partial Inactivation for New D esign
The PINs ident i fied in see 6.6 are
INACTIVE FOR NEW DES IGN
AFTER 6 June 2014
FOR NEW DESIGN USE CID A -A-59789
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 2
1. SCOPE
1.1 Scope. This dr awing describes the requirement s for a family of 5 wedge metal card-retainers int ended to hold cir c uit card
assemblies or printed wiring assemblies in their install ed positions.
1.2 Part or Ident i fying Number (P IN). The complete PIN shall be as shown in the following example:
89064
│
│
│
───┴───
Drawing
number
–50
│
│
│
───┴───
Dash number
(see table I)
A
│
│
│
─────┴─────
Configuration
(see 3.1 and f igure 1)
N
│
│
│
─────┴─────
Mounting opt ions
(see 3.1.1 and table II)
WV
│
│
│
─────┴─────
Other options
(see 3.1.2)
2. APPLICABLE DOCUMENTS
2.1 General. The documents list ed i n this section are specified in sections 3 and 4 of this specification. This section does not
include documents cited in ot her sections of t his specification or recommended for additional information or as examples. While
every effort has been made to ens ure the compl eteness of this li s t, document user s are cautioned that they must meet all
specified requirements of documents cited i n sections 3 and 4 of this spec i fication, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, stan dards, and handbooks. The foll owing specifications, standards, and handbooks form a par t of this
document to t he extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract (s ee 6.2).
SPECIFICATIONS
DEPARTMENT OF DEFENSE
MIL–DTL–5002 – Surface Tr eatments and Inorganic Coatings for Metal Surf aces of Weapon Systems.
MIL–DTL–5541 – Chemical Conv ersion Coating s On Aluminum And Alum inum Alloys.
STANDARDS
DEPARTMENT OF DEFENSE
MIL–STD–1285 – Marking of Electrical and Electronic Parts.
(Copies of these documents a re available online at http://quicksearch.dla.mil.)
2.3 Non-Government publications. The follo wi ng documents form a part of this document to the extent specified h erein.
Unless otherwise specifi ed, the issues of t hese documents ar e those cited in the solicitation or contract .
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC.
AIA/NAS NAS 620 – Washer, Flat , Reduced Outside Diameter.
AIA/NAS NASM35338 – Washer, Lock-Spring, Helical, Regular (Med ium) Series.
AIA/NAS NASM122116-122155 – Insert, CRES Hel i cal Coil, Coar s e Thread, 1–1/2 Di a. Nominal Length.
(Copies of these documents a re available online at http://www.aia–aerospace.org or from the Aerospace Industries
Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209–3901.)
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 3
ASTM INTERNATIONAL (ASTM)
ASTM A484/A484M – Standard Specification for General Require ments for Stain less Steel Bars, Billets, and
Forgings.
ASTM A582/58 2M – Standar d Specificatio n for Free-Machining Stainless St eel Bars.
ASTM B194 – Standard Specification for Copper-Ber yllium Alloy Plate, Sheet, Stri p, and Rolled Bar.
ASTM B221 – Standard Specification for A l uminum and Alum inum-Alloy Extruded Bars, Rods , Wire,
Profiles and Tubes.
(Copies of these documents a re available online at http://www.astm.org or from the ASTM Internationa l, P.O. Box C700, 100
Barr Harbor Dr ive, West Conshohocken, PA 19428–2959.)
SAE INTERNATIONAL (SAE)
SAE AMS-QQ-N-290 – Nickel Plating (Electrodeposited)
SAE AMS-QQ-S-763 – Steel, Corros ion Resistant, Bars, Wire, S hapes, and Forgings
SAE AMS 5518 – Steel, Corrosion Resistant, Sheet and Stri p 18Cr - 8Ni Cold Rol led, 150 ksi ( 1034 MPa)
Tensile Str ength
SAE AMS 5904 – Steel, Corrosion-Resistant , Sheet and Strip 18Cr - 9.0Ni (S A E 30302) Cold Rolled 1/2 Hard,
150ksi (1034 MPa) Tensile Strength
(Copies of these documents ar e available onl ine at http://www.sae.org or from SAE World Headquarters, 400 Comm onwealth
Drive, Warrendale, PA 15096–0001.)
(Non-Government standards and other publications are nor mally availabl e from the organizations which pr epare or which
distribute the documents. These documents al s o may be available i n or through libr aries or other infor mational services.)
2.4 Order of precedence. Unless otherwise noted herein or i n the contract, in the event of a confl ict between the text of this
document and the references cited herein, the text of this doc ument takes precedence. Nothing i n this document, however,
supersedes applicable laws and regulations unless a specific exemption h as been obtained.
3. REQUIREMENTS
3.1 Interface and physical dimensions. S ee tables I and II and fi gure 1. Som e card holders conf orming to this drawing may
be supplied in a unassembled condi tion. See 6.8 for additional information.
3.1.1 Mounting to circuit card assembly. Card holders conforming to this dr awing are secur ed to the circuit c ard assembly
using either adhesives, braz i ng, fastener, or rivets. Card holders are availa ble either with mounting holes as shown on figure 1
or without mounting holes. Ther e are three options for designs with mounting holes. The hole opti ons are counterbore holes or
two styles of tapped holes.
3.1.1.1 No mounting holes (for adhesive or brazing mounting). Card holders without mountin g holes (to facilitate adhesive or
brazing mount ing) shall contain an "N" in the P IN.
3.1.1.2 Count er bore holes (for r i v et mounting). Counterbore holes shall be .068/.073 inch (1. 73/1.85 mm) diamet er
countersunk 100 degrees by .140 inch (3.56 mm) di am eter through holes with an access/clearance h ole .156 inch (3.96)
diameter by .2 00 inch (5.08 mm) deep for configurations "A", " C" , "D", and "E" and .175 inch (4.45 mm) deep for configuration
"B". Card retainers with counterbore holes shall include a suffix "R" in the PIN.
3.1.1.3 Tapped holes (for threaded fastener s ). Card retainers with 2–56 UNF t apped through holes s hall include a suffix "S"
in the PIN. Card retainers with 0–80 UNF tapped thr ough holes shall include a suffi x "T" in the PIN (see figure 1, table I, and
1.2).
3.1.2 Alignment springs. Co nfigurations "A", "B", "C", and " D" that have no mount ing holes or tapped mounting holes shall
have 3 alignme nt springs, one in the mounting bod y and one in each of the two intermediate bodies. Configurations "A " , "B",
"C", and "D" that use rivets for mounting holes shall have 2 alignm ent springs, one i n each of the two intermediate bodies. The
mounting body will not have an alignment spring. Configurations "E", "F", "G", and "H" shall have 3 alignment s prings, one in
the mounting b ody and one in each of the two intermediate bodies for al l mounting opt ions.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 4
3.1.3 Optiona l features.
3.1.3.1 Flat washer and lockwa sher. A flat washer and lockwasher feature are available (s ee figure 1 and table I). Card
retainers with the optional fl at washer and loc kwasher feature shall includ e a suffix "W" in the P IN (see fig ure 1 and 1.2).
3.1.3.2 Visua l l oc k indication. An optional vi s ual lock indication feature is available (see figure 1 and table I). Card retainers
with the optional visual lock i ndication shal l include a suffix "V" in the PIN (see figure 1 and 1.2).
TABLE I. Card retainer d imensions and co nfigurations . 1/ 2/
PIN
89064 Configuration Dimension "L"
(length) +.02 / –.03
(+0.5 / –0.8 mm)
Dimension "A"
(mounting body)
±.01 (0.3 mm)
Dimension "B"
(mounting hole)
±.02 (0.5 mm)
Dimension "C" Number of
mounting
holes
–50 A, E 5.00 (127.0) 1.50 (38.1) .30 (7.6) 1.15 (29.2) 2
–50 B, F 5.00 (127.0) 1.50 (38.1) .30 (7.6) 1.15 (29.2) 2
–50 C, G 5.00 (127.0) 1.50 (38.1) .50 (12.7) 1.15 (29.2) 2
–60 A, E 6.00 (152.4) 2.50 (63.5) .80 (20.3) 1.15 (29.2) 2
–60 B, F 6.00 (152.4) 2.50 (63.5) .80 (20.3) 1.15 (29.2) 2
–60 C, G 6.00 (152.4) 2.50 (63.5) 1.00 (25.4) 1.15 (29.2) 2
–65 A, E 6.50 (165.1) 3.00 (76.2) 1.05 (26.7) 1.15 (29.2) 2
–65 B, F 6.50 (165.1) 3.00 (76.2) 1.05 (26.7) 1.15 (29.2) 2
–65 C, G 6.50 (165.1) 3.00 (76.2) 1.25 (26.7) 1.15 (29. 2) 2
–70 D, H 7.00 (177. 8) 3.50 (88.9) . 40 (10.2) 1.15 (29.2) 4
–75 D, H 7.50 (190. 5) 4.00 (101.6) .65 (16.5) 1.15 (29. 2) 4
–80 D, H 8.00 (203. 2) 3.50 (88.9) . 40 (10.2) 1.65 (41.9) 4
–85 D, H 8.50 (215. 9) 4.00 (101.6) .65 (16.5) 1.65 (41. 9) 4
1/ Dimensions are in inches. Metric equivalents are given for general information only.
2/ Tolerances, unless other wise specified, are ±.02 inch (0.5 m m), for 2 place decimals and ±.010 inch (0.25 mm), for 3
place decimals.
TABLE II. Mounting design.
PIN modifier Attribute
N Without mounting holes
R Counterbore holes
S 2–56 UNC tapped holes
T 0–80 UNF tapped holes
3.2 Materials.
3.2.1 Alignment spring. The alignment spring s hall be either beryllium copper in ac corda nce with ASTM B194 or equivalent,
or stainless s teel in accordance with SAE AMS 5518, SAE AMS 5904, or equivalent.
3.2.2 Bodies and wedges. The bo dies (mounting and intermediate) and wedges material shall be aluminum alloy in
accordance with ASTM B221 or equivalent.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 5
3.2.3 Flatwasher. The flatwasher (included wit h the locking feature) shall com ply with AIA/NAS NAS 620 or equiv alent.
3.2.4 Lockwasher. The lockwasher (included with the lock ing feature) shall comply with AIA/NAS NASM35338-135 or
equivalent.
3.2.5 Screw. The sc rew material shall be stainless st eel in accordanc e with SAE AMS-QQ-S-763, ASTM A484/A484M, or
ASTM A582/58 2M or equivale nt.
3.2.6 Screw retention.
3.2.6.1 Captive nut. When a captiv e nut is used, the captive nut mat erial shall be stainless steel, type 303, in accordance
with ASTM A582/58 2M.
3.2.6.2 Helical insert. When a helical insert is used, the helic al i nsert shall be i n ac cordance with AIA/NAS NASM122116.
3.2.7 Visual indicator.
3.2.7.1 Cup. The cup material for visual i ndicators shall stainless steel in accordance with ASTM B194, SAE AMS 5904, or
equivalent.
3.2.7.2 Spring. The spr i ng material for visual indicator s shall be stainless steel.
3.3 Finish.
3.3.1 Alignment spring. Stainless steel ali gnment springs shall be passivate in accordance with MIL–DTL–5002. Beryllium
copper alignment springs shall be nickel plate in accordance with SAE AMS-QQ-N-290, class 1, grade G, bright (see 6.1.1
regarding nickel plating).
3.3.2 Bodies and wedges. The bo dies and wedges shall be chemical finish in accordance with MIL–DTL–5541, class 1A.
3.3.3 Flat washer, lockwasher, captive nut, helical insert, and screw. The flatwasher, lockwasher, capt i ve nut, helical insert,
and screw shal l be passivate in acc ordance with MIL–DTL–5002.
3.3.4 Visual lock cup and spring (when applic able). The visual lock cup and s pr i ng shall be passivate in accordance with
MIL–DTL–5002.
3.4 Certificat e of compliance. A certificat e of compliance shal l be required from a manufacturer in order to be listed as an
approved source of supply in 6.8. The certificate of compli ance, submitted to DLA Land and Marit i me VAC prior to listing as an
approved source of supply, s hall s tate that the m anufacturer's product meet s the requirements herein.
3.5 Optional statement of compliance in lieu of performing conformance ins pections. The acquiring activity, at its di s cretion,
may accept from the manufacturer a statement of complianc e i n lieu of the manufacturer performing the inspection of produc t for
delivery tests (see 4.2.2 and 6.2.b).
3.6 Marking. Marking of t he c ard holder is not required; however, each unit package shall be mark ed in accordance with
MIL–STD–1285 and include the PIN as spec i fied herein (see 1.2), the manufacturer’s name or Commercial and Government
Entity (CAGE) code, and date lot codes.
3.7 Recycled, r ecovered, or env ironmentall y preferable mat erials. Recycled, recovered, or environm entally prefer able
materials should be used to the maximum extent pos sible provided that the material meets or exceeds the operational and
maintenance r equirements, and promotes economically advantageous life cycle costs.
3.8 Workmanship. Card hold ers shall be free from surface and finish flaws that affect life or s er viceability. Car d holders shall
be finished smooth and shall have rounded edges with no evidenc e of chipping, cracking, deterioration, disintegration, or burrs.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 6
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.010
.06 0.25
1.5 .09
.14 2.3
3.6 .165
.20 4.19
5.1 .225
.260
.33
5.72
6.61
8.4
.330
.50
.900
8.38
12.7
22.86
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ± .02 inch (0.5 mm), for 2 places and ± .010 inch ( 0.25 mm),
for 3 places.
3. See 3.1.2 for r equirements f or the number of alig nment springs and their placement .
4. See table I for L, A, B, and C dime ns i ons and toleranc es.
FIGURE 1. Card holder dimensio ns and configurat ions.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 7
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.010
.06 0.25
1.5 .09
.14 2.3
3.6 .165
.20 4.19
5.1 .225
.275
.290
5.72
6.98
7.37
.33
.50
.900
8.4
12.7
22.86
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ± .02 inch (0.5 mm), for 2 places and ± .010 inch ( 0.25 mm),
for 3 places.
3. See 3.1.2 for r equirements f or the number of alig nment springs and their placement .
4. See table I for L, A, B, and C dime ns i ons and toleranc es.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 8
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.010
.06 0.25
1.5 .09
.14 2.3
3.6 .165
.20
.225
4.19
5.1
5.72
.260
.33
.330
6.61
8.4
8.38
.50
.500
.900
12.7
12.70
22.86
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ±.02 inch (0.5 mm), for 2 places and ±.010 inch ( 0.25 mm),
for 3 places.
3. See 3.1.2 for r equirements f or the number of alig nment springs and their placement .
4. See table I for L, A, B, and C dime ns i ons and toleranc es.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 9
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005
.06
.09
0.13
1.5
2.3
.14
.165
.20
3.6
4.19
5.1
.225
.260
.33
5.72
6.61
8.4
.330
.50
.900
8.38
12.7
22.86
1.800
2.700 45.72
68.58
NOTES:
1. Dimensions are in inches. M etric equivalents are given for i nformation only.
2. Unless otherwise specified, tolera nc es are ± .02 inch (0.5 mm), for 2 places and ± .010 inch ( 0.25 mm),
for 3 places.
3. See 3.1.2 for r equirements f or the number of alig nment springs and their placement .
4. See table I for L, A, B, and C dime ns ions and tolerances.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 10
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005
.06 0.13
1.5 .09
.165 2.3
4.19 .20
.225
.235
5.1
5.72
5.97
.270
.325
.33
6.86
8.36
8.4
.330
.50
.900
8.38
12.7
22.86
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ± .02 inch (0.5 mm), for 2 places and ± .010 inch ( 0.25 mm),
for 3 places.
3. See table I for L, A, B, and C dime ns i ons and toleranc es.
4. Screw advance is .14 inch (3. 6 mm) maximum for card holders without the visual indicator and .31 inch
(7.9 mm) maxim um on card holders with the visual indicator option.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 11
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005
.06 0.13
1.5 .09
.165 2.3
4.19 .20
.225 5.1
5.72 .235
.275 5.97
6.99 .33
.50
.900
8.4
12.7
22.86
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ±.02 inch (0.5 mm), for 2 places and ±.010 inch ( 0.25 mm),
for 3 places.
3. See table I for L, A, B, and C dime ns i ons and toleranc es.
4. Screw advance is .14 inch (3. 6 mm) maximum for card holders without the visual indicator and .31 inch
(7.9 mm) maxim um on card holders with the visual indicator option.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 12
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005
.06 0.13
1.5 .09
.165 2.3
4.19 .20
.225 5.1
5.72 .235
.270
.325
5.97
6.86
8.26
.33
.50
.500
8.4
12.7
12.70
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ±.02 inch (0.5 mm), for 2 places and ±.010 inch ( 0.25 mm),
for 3 places.
3. See table I for L, A, B, and C dime ns i ons and toleranc es.
4. Screw advance is .14 inch (3. 6 mm) maximum for card holders without the visual indicator and .31 inch
(7.9 mm) maxim um on card holders with the visual indicator option.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 13
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005
.06
.09
0.13
1.5
2.3
.165
.20 4.19
5.1 .225
.235
.270
5.72
5.97
6.86
.325
.33
.50
8.26
8.4
12.7
.900
1.800
2.700
22.86
45.72
68.58
NOTES:
1. Dimensio ns are in inches. Metric equivalents are given for information only.
2. Unless otherwise specified, tolera nc es are ±.02 inch (0.5 mm), for 2 places and ±.010 inch ( 0.25 mm),
for 3 places.
3. See table I for L, A, B, and C dime ns i ons and toleranc es.
4. Screw advance is .14 inch (3. 6 mm) maximum for card holders without the visual indicator and .31 inch
(7.9 mm) maxim um on card holders with the visual indicator option.
FIGURE 1. Card holder dimensio ns and configurat ions – Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 14
4. VERIFICATION
4.1 Sampling and inspection. Unless otherwise s pecified in the contract or order, the contract or is responsible for the
performance of all inspection requirement s as specified herei n. Except as otherwise specifi ed in the contract, the cont ractor
may use their own or any other facilities suitable for the per formance of the inspection requirements sp ecified herein, unless
disapproved by the Government. The Government reserves t he right to perform any of the inspecti ons set forth in this drawing
where such ins pec tions are deemed necessar y to assure supplies and services conform to prescr ibed requirements.
4.2 Conformance i nspections.
4.2.1 Inspection of product for delivery. Ins pection of product for deliver y shall consist of visual and mechanical inspections
of interface a nd physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.8). Criteria for defects are l isted in
4.2.1.3.
4.2.1.1 Sampl ing plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or
more defects a re found, the lot shall be rejected. Criteria for defects are listed in 4.2.1.3.
TABLE II. Sampling plan.
Lot size Normal Tightened
2
to
25
3 5
26
to
50
5 6
51
to
90
6 7
91
to
150
7 11
151
to
280
10 13
281
to
500
11 16
501
to
1,200
15 19
1,201
to
3,200
18 23
3,201
to
10,000
22 29
10,001
and
over
29 35
4.2.1.2 Rejected lots. If an ins pection lot is rejec ted after nor m al sampling inspec tion, the manufacturer may rework it to
correct the defects, or screen out the defective parts and resubmit for inspection. Resub mitted lots shal l be i nspected by
selecting a random sample of parts in accor dance with tabl e II, tightened sampling. I f one or more defect s are found in this
sample, the lot shall be rejected and shall not be s upplied to this specification. Resubmitted lot s which are acceptable shall be
clearly identified as reins pec ted lots.
4.2.1.3 Defect ive character istics and properties. Dim ens ional characteristics are considered defective when out of tolerance.
Physical and functional properties are cons i dered defective when outside t he specified minim um, maximum, or range as
applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use,
performance r equirements, or environmental survival of the part.
4.2.2 Optiona l statement of compliance. The acquiring activ i ty, at its discret i on, may accept a statement of com pli ance in lieu
of the manufac turer performing the inspection of product for delivery (see 6.2.b).
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging re qui rements shall be as specified in the contract or order (see 6.2).
When actual p ac kaging of mater i el i s to be performed by DoD personnel, these personnel need to contact the responsible
packaging act ivity to ascertain requisit e packaging requirements. Packaging requir ements are maintained by th e Inventory
Control Point's packaging activity within t he Military Department or Defense Agency, or within the Military Department's System
Command. Pack aging data retriev al is available from the managing Military Department's or Defense Agency's automated
packaging fil es, CD-ROM products, or by contact i ng the respons ible packaging activity.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 15
6. NOTES
(This section contains information of a general or explanatory nature which m ay be helpful, but is not mandatory.)
6.1 Intended u se. Card holders conforming to this drawing are intended for use when performance specifications do not exist
and qualifie d military devices that will perf orm the required function are not available for OEM applicatio n.
6.1.1 Environmentally pref erable material. Environm entally prefer able materia ls should be used to the maximum extent
possible to meet the requirements of this spe cification. A s of the dating of this document, the U.S. Environmental Protection
Agency (EPA) is focusing efforts on reducing 31 pr iority chemi c al s . The list of c hemicals and additional information is available
on their website http://www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the list of 31 priority chemicals are c admium,
lead, and merc ury. Use of these materials should be minimized or eliminated unless needed to m eet the requirem ents specifi ed
herein (see 3.2).
6.1.2 Guidance on use of alternat ive parts with less hazardous or nonhazardous materials. This drawing provides for a
number of alternative plating materials via the PIN. Us er s should select the PIN with the least hazardo us material that meets
the form, fit, and function requ i r ements of their application.
6.2 Acquisiti on requirements . The acquisition requirement s should specify the following:
a. Complete PIN (see 1.2).
b. Requirements for delivery of one copy of the c onformance inspec tion data or cer tificate of compliance that parts have
passed conformance inspection with each shipment of parts by the manufactur er.
c. Whether the m anufacturer performs the product for delivery inspection (4.2.1) or provi des an optional statement of
compliance (4.2.2).
d. Requirements for notification of change in product to the contracting activ i ty, if applicable.
e. Requirements for packaging and packing.
6.3 Users of record. Coordinatio n of this docume nt for future revisions are coordinated only with the suggested sources of
supply and the us ers of record of this document. Requests to be added as a recorded user of this drawing should be in writing
to: DLA Land and Maritim e, ATTN: VAC, Post Office Box 3990, Columbus, OH 43216–5000 or by electr oni c mail at
5998.Documents@dla.mil or by facsimile (614) 692–6939 or DSN 850–6939.
6.4 Replaceability. Retainers covered herein replace similar commercial dev i ces covered b y contractor-prepared
specificati ons or drawings.
6.5 Changes from previous is s ue. Asterisks are not used in this r evision to identify changes with res pect to the previous
revision, due t o the extensiv eness of the changes .
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 16
6.6 Supersession data concerning inactive for new design PINs. The i nac tive for new design part numbers with
corresponding for new desig n use part numbers ar e l isted below. Configurations "B", "C", "F", "G" and "H" have not been
inactivated f or new design and are not covered b y A–A–59789.
Superseded
(old) part number
Superseding
(new) part number
Superseded
(old) part number
Superseding
(new) part number
89064–50AN
AA59789/21AC50N
89064–50ANW
AA59789/21FC50N
89064–50AR
AA59789/21AC50R
89064–50ARW
AA59789/21FC50R
89064–50AS AA59789/21AC50S 89064–50ASW AA59789/21FC50S
89064–50AT AA59789/21AC50T 89064–50ATW AA59789/21FC50T
89064–50EN
AA59789/21CC50N
89064–50ENW
AA59789/21WC50N
89064–50ER
AA59789/21CC50R
89064–50ERW
AA59789/21WC50R
89064–50ES AA59789/21CC50S 89064–50ESW AA59789/21WC50S
89064–50ET
AA59789/21CC50T
89064–50ETW
AA59789/21WC50T
89064–60AN AA59789/21AC60N 89064–60ANW AA59789/21FC60N
89064–60AR
AA59789/21AC60R
89064–60ARW
AA59789/21FC60R
89064–60AS AA59789/21AC60S 89064–60ASW AA59789/21FC60S
89064–60AT
AA59789/21AC60T
89064–60ATW
AA59789/21FC60T
89064–60EN AA59789/21CC60N 89064–60ENW AA59789/21WC60N
89064–65ER AA59789/21CC65R 89064–65ERW AA59789/21WC65R
89064–65ES
AA59789/21CC65S
89064–65ESW
AA59789/21WC65S
89064–65ET AA59789/21CC65T 89064–65ETW AA59789/21WC65T
89064–65AN AA59789/21AC65N 89064–65ANW AA59789/21FC65N
89064–65AR
AA59789/21AC65R
89064–65ARW
AA59789/21FC65R
89064–65AS
AA59789/21AC65S
89064–65ASW
AA59789/21FC65S
89064–65AT AA59789/21AC65T 89064–65ATW AA59789/21FC65T
89064–65EN AA59789/21CC65N 89064–65ENW AA59789/21WC65N
89064–65ER
AA59789/21CC65R
89064–65ERW
AA59789/21WC65R
89064–65ES
AA59789/21CC65S
89064–65ESW
AA59789/21WC65S
89064–65ET AA59789/21CC65T 89064–65ETW AA59789/21WC65T
89064–70AN
AA59789/23AC70N
89064–70ANW
AA59789/23FC70N
89064–70AR AA59789/23AC70R 89064–70ARW AA59789/23FC70R
89064–70AS
AA59789/23AC70S
89064–70ASW
AA59789/23FC70S
89064–70AT
AA59789/23AC70T
89064–70ATW
AA59789/23FC70T
89064–70EN
AA59789/23CC70N
89064–70ENW
AA59789/23WC70N
89064–70ER AA59789/23CC70R 89064–70ERW AA59789/23WC70R
89064–70ES
AA59789/23CC70S
89064–70ESW
AA59789/23WC70S
89064–70ET
AA59789/23CC70T
89064–70ETW
AA59789/23WC70T
89064–75AN
AA59789/23AC75N
89064–75ANW
AA59789/23FC75N
89064–75AR AA59789/23AC75R 89064–75ARW AA59789/23FC75R
89064–75AS
AA59789/23AC75S
89064–75ASW
AA59789/23FC75S
89064–75AT
AA59789/23AC75T
89064–75ATW
AA59789/23FC75T
89064–75EN
AA59789/23CC75N
89064–75ENW
AA59789/23WC75N
89064–75ER
AA59789/23CC75R
89064–75ERW
AA59789/23WC75R
89064–75ES AA59789/23CC75S 89064–75ESW AA59789/23WC75S
89064–75ET
AA59789/23CC75T
89064–75ETW
AA59789/23WC75T
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 17
Superseded
(old) part number Superseding
(new) part number Superseded
(old) part number Superseding
(new) part number
89064–80AN AA59789/23AC80N 89064–80ANW AA59789/23FC80N
89064–80AR AA59789/23AC80R 89064–80ARW AA59789/23FC80R
89064–80AS AA59789/23AC80S 89064–80ASW AA59789/23FC80S
89064–80AT AA59789/23AC80T 89064–80ATW AA59789/23FC80T
89064–80EN AA59789/23CC80N 89064–80ENW AA59789/23WC80N
89064–80ER AA59789/23CC80R 89064–80ERW AA59789/23WC80R
89064–80ES AA59789/23CC80S 89064–80ESW AA59789/23WC80S
89064–80ET AA59789/23CC80T 89064–80ETW AA59789/23WC80T
89064–85AN AA59789/23AC85N 89064–85ANW AA59789/23FC85N
89064–85AR AA59789/23AC85R 89064–85ARW AA59789/23FC85R
89064–85AS AA59789/23AC85S 89064–85ASW AA59789/23FC85S
89064–85AT AA59789/23AC85T 89064–85ATW AA59789/23FC85T
89064–85EN AA59789/23CC85N 89064–85ENW AA59789/23WC85N
89064–85ER AA59789/23CC85R 89064–85ERW AA59789/23WC85R
89064–85ES AA59789/23CC85S 89064–85ESW AA59789/23WC85S
89064–85ET AA59789/23CC85T 89064–85ETW AA59789/23WC85T
89064–60ANV AA59789/22AC60N 89064–60ANWV AA59789/22FC60N
89064–60ARV AA59789/22AC60R 89064–60ARWV AA59789/22FC60R
89064–60ASV AA59789/22AC60S 89064–60ASWV AA59789/22FC60S
89064–60ATV AA59789/22AC60T 89064–60ATWV AA59789/22FC60T
89064–60ENV AA59789/22CC60N 89064–60ENWV AA59789/22WC60N
89064–65ERV AA59789/22CC65R 89064–65ERWV AA59789/22WC65R
89064–65ESV AA59789/22CC65S 89064–65ESWV AA59789/22WC65S
89064–65ETV AA59789/22CC65T 89064–65ETWV AA59789/22WC65T
89064–65ANV AA59789/22AC65N 89064–65ANWV AA59789/22FC65N
89064–65ARV AA59789/22AC65R 89064–65ARWV AA59789/22FC65R
89064–65ASV AA59789/22AC65S 89064–65ASWV AA59789/22FC65S
89064–65ATV AA59789/22AC65T 89064–65ATWV AA59789/22FC65T
89064–65ENV AA59789/22CC65N 89064–65ENWV AA59789/22WC65N
89064–65ERV AA59789/22CC65R 89064–65ERWV AA59789/22WC65R
89064–65ESV AA59789/22CC65S 89064–65ESWV AA59789/22WC65S
89064–65ETV AA59789/22CC65T 89064–65ETWV AA59789/22WC65T
89064–70ANV AA59789/24AC70N 89064–70ANWV AA59789/24FC70N
89064–70ARV AA59789/24AC70R 89064–70ARWV AA59789/24FC70R
89064–70ASV AA59789/24AC70S 89064–70ASWV AA59789/24FC70S
89064–70ATV AA59789/24AC70T 89064–70ATWV AA59789/24FC70T
89064–70ENV AA59789/24CC70N 89064–70ENWV AA59789/24WC70N
89064–70ERV AA59789/24CC70R 89064–70ERWV AA59789/24WC70R
89064–70ESV AA59789/24CC70S 89064–70ESWV AA59789/24WC70S
89064–70ETV AA59789/24CC70T 89064–70ETWV AA59789/24WC70T
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 18
Superseded
(old) part number Superseding
(new) part number Superseded
(old) part number Superseding
(new) part number
89064–75ANV
AA59789/24AC75N
89064–75ANWV
AA59789/24FC75N
89064–75ARV
AA59789/24AC75R
89064–75ARWV
AA59789/24FC75R
89064–75ASV AA59789/24AC75S 89064–75ASWV AA59789/24FC75S
89064–75ATV
AA59789/24AC75T
89064–75ATWV
AA59789/24FC75T
89064–75ENV
AA59789/24CC75N
89064–75ENWV
AA59789/24WC75N
89064–75ERV
AA59789/24CC75R
89064–75ERWV
AA59789/24WC75R
89064–75ESV AA59789/24CC75S 89064–75ESWV AA59789/24WC75S
89064–75ETV
AA59789/24CC75T
89064–75ETWV
AA59789/24WC75T
89064–80ANV AA59789/24AC80N 89064–80ANWV AA59789/24FC80N
89064–80ARV
AA59789/24AC80R
89064–80ARWV
AA59789/24FC80R
89064–80ASV
AA59789/24AC80S
89064–80ASWV
AA59789/24FC80S
89064–80ATV AA59789/24AC80T 89064–80ATWV AA59789/24FC80T
89064–80ENV AA59789/24CC80N 89064–80ENWV AA59789/24WC80N
89064–80ERV
AA59789/24CC80R
89064–80ERWV
AA59789/24WC80R
89064–80ESV
AA59789/24CC80S
89064–80ESWV
AA59789/24WC80S
89064–80ETV AA59789/24CC80T 89064–80ETWV AA59789/24WC80T
89064–85ANV AA59789/24AC85N 89064–85ANWV AA59789/24FC85N
89064–85ARV
AA59789/24AC85R
89064–85ARWV
AA59789/24FC85R
89064–85ASV
AA59789/24AC85S
89064–85ASWV
AA59789/24FC85S
89064–85ATV AA59789/24AC85T 89064–85ATWV AA59789/24FC85T
89064–85ENV
AA59789/24CC85N
89064–85ENWV
AA59789/24WC85N
89064–85ERV AA59789/24CC85R 89064–85ERWV AA59789/24WC85R
89064–85ESV
AA59789/24CC85S
89064–85ESWV
AA59789/24WC85S
89064–85ETV AA59789/24CC85T 89064–85ETWV AA59789/24WC85T
6.7 Supersession data concerning previous revisions. The original is s ue of this drawing PIN did not contain a suffix to
designate length, configuration, or other options. Superseded part numbers are listed below.
New PIN
89064– Previous
part number
89064–
New PIN
89064– Previous
part number
89064–
New PIN
89064– Previous
part number
89064–
New PIN
89064– Previous
part number
89064–
50AN 01A 60ANV 07A 60BN 13A 50CNV 19A
50AS 01M 60ASV 07M 60BS 13M 50CRV 19M
50ANW 02A 60ANWV 08A 60BNW 14A 50CNWV 20A
50ASW 02M 60ASWV 08M 60BSW 14M 50CRWV 20M
50ANV 03A 50BN 09A 60BNV 15A 60CN 21A
50ASV 03M 50BS 09M 60BSV 15M 60CR 21M
50ANWV 04A 50BNW 10A 60BNWV 16A 60CNW 22A
50ASWV 04M 50BSW 10M 60BSWV 16M 60CRW 22M
60AN 05A 50BNV 11A 50CN 17A 60CNV 23A
60AS 05M 50BSV 11M 50CS 17M 60CRV 23M
60ANW 06A 50BNWV 12A 50CNW 18A 60CNWV 24A
60ASW 06M 50BSWV 12M 50CRW 18M 60CRWV 24M
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 19
6.8 Approved sources of suppl y. Approved sourc es of supply are li s ted herein. Additional sourc es will be added as they
become available. The vendor s listed herein hav e agreed with t hi s drawing and have submitted a certificate of compliance (see
3.4 herein) to DLA Land and Mar i time, ATTN: V A C , Post Office Box 3990, Columbus, OH 43218–3990 or by electronic m ail at
"5998.Documents@dla.mil" or by facsimile ( 614) 692–6939 or DSN 850–6939.
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
Vendor
CAGE Vendor name and address
–50EN G5225–89064–50EN –50ENV G5225–89064–50ENV
–50ER G5225–89064–50ER –50ERV G5225–89064–50ERV 5BG68 American Circuit Card Retainers, Inc.
2310 E. Orangethorpe Avenue
Anaheim, CA 92806–1231
–50ES G5225–89064–50ES –50ESV G5225–89064–50ESV
–50ET G5225–89064–50ET –50ETV G5225–89064–50ETV
–50ENW G5225–89064–50ENW –50ENWV G5225–89064–50ENWV
–50ERW G5225–89064–50ERW –50ERWV G5225–89064–50ERWV Telephone: (714) 738–6194
–50ESW G5225–89064–50ESW –50ESWV G5225–89064–50ESWV Facsimile: (714) 446–0119
–50ETW G5225–89064–50ETW –50ETWV G5225–89064–50ETWV
–50FN G5220–89064–50FN –50FNV G5220–89064–50FNV E-mail: sales@accrmfg.com
–50FR G5220–89064–50FR –50FRV G5220–89064–50FRV
–50FS G5220–89064–50FS –50FSV G5220–89064–50FSV URL: http://www.accrmfg.com
–50FT G5220–89064–50FT –50FTV G5220–89064–50FTV
–50FNW G5220–89064–50FNW –50FNWV G5220–89064–50FNWV
–50FRW G5220–89064–50FRW –50FRWV G5220–89064–50FRWV
–50FSW G5220–89064–50FSW –50FSWV G5220–89064–50FSWV
–50FTW G5220–89064–50FTW –50FTWV G5220–89064–50FTWV
–60EN G5225–89064–60EN –60ENV G5225–89064–60ENV
–60ER G5225–89064–60ER –60ERV G5225–89064–60ERV
–60ES G5225–89064–60ES –60ESV G5225–89064–60ESV
–60ET G5225–89064–60ET –60ETV G5225–89064–60ETV
–60ENW G5225–89064–60ENW –60ENWV G5225–89064–60ENWV
–60ERW G5225–89064–60ERW –60ERWV G5225–89064–60ERWV
–60ESW G5225–89064–60ESW –60ESWV G5225–89064–60ESWV
–60ETW G5225–89064–60ETW –60ETWV G5225–89064–60ETWV
–60FN G5220–89064–60FN –60FNV G5220–89064–60FNV
–60FR G5220–89064–60FR –60FRV G5220–89064–60FRV
–60FS G5220–89064–60FS –60FSV G5220–89064–60FSV
–60FT G5220–89064–60FT –60FTV G5220–89064–60FTV
–60FNW G5220–89064–60FNW –60FNWV G5220–89064–60FNWV
–60FRW G5220–89064–60FRW –60FRWV G5220–89064–60FRWV
–60FSW G5220–89064–60FSW –60FSWV G5220–89064–60FSWV
–60FTW G5220–89064–60FTW –60FTWV G5220–89064–60FTWV
–65EN G5225–89064–65EN –65ENV G5225–89064–65ENV
–65ER G5225–89064–65ER –65ERV G5225–89064–65ERV
–65ES G5225–89064–65ES –65ESV G5225–89064–65ESV
–65ET G5225–89064–65ET –65ETV G5225–89064–65ETV
See footnotes at end of table.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 20
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
Vendor
CAGE Vendor name and address
–65ENW G5225–89064–65ENW –65ENWV G5225–89064–65ENWV
–65ERW G5225–89064–65ERW –65ERWV G5225–89064–65ERWV 5BG68 American Circuit Card Retainers, Inc.
2310 E. Orangethorpe Avenue
Anaheim, CA 92806–1231
–65ESW G5225–89064–65ESW –65ESWV G5225–89064–65ESWV
–65ETW G5225–89064–65ETW –65ETWV G5225–89064–65ETWV
–65FN G5220–89064–65FN –65FNV G5220–89064–65FNV
–65FR G5220–89064–65FR –65FRV G5220–89064–65FRV Telephone: (714) 738–6194
–65FS G5220–89064–65FS –65FSV G5220–89064–65FSV Facsimile: (714) 446–0119
–65FT G5220–89064–65FT –65FTV G5220–89064–65FTV
–65FNW G5220–89064–65FNW –65FNWV G5220–89064–65FNWV E-mail: sales@accrmfg.com
–65FRW G5220–89064–65FRW –65FRWV G5220–89064–65FRWV
–65FSW G5220–89064–65FSW –65FSWV G5220–89064–65FSWV URL: http://www.accrmfg.com
–65FTW G5220–89064–65FTW –65FTWV G5220–89064–65FTWV
–70HN G5225–89064–70HN –70HNV G5225–89064–70HNV
–70HR G5225–89064–70HR –70HRV G5225–89064–70HRV
–70HS G5225–89064–70HS –70HSV G5225–89064–70HSV
–70HT G5225–89064–70HT –70HTV G5225–89064–70HTV
–70HNW G5225–89064–70HNW –70HNWV G5225–89064–70HNWV
–70HRW G5225–89064–70HRW –70HRWV G5225–89064–70HRWV
–70HSW G5225–89064–70HSW –70HSWV G5225–89064–70HSWV
–70HTW G5225–89064–70HTW –70HTWV G5225–89064–70HTWV
–75HN G5225–89064–75HN –75HNV G5225–89064–75HNV
–75HR G5225–89064–75HR –75HRV G5225–89064–75HRV
–75HS G5225–89064–75HS –75HSV G5225–89064–75HSV
–75HT G5225–89064–75HT –75HTV G5225–89064–75HTV
–75HNW G5225–89064–75HNW –75HNWV G5225–89064–75HNWV
–75HRW G5225–89064–75HRW –75HRWV G5225–89064–75HRWV
–75HSW G5225–89064–75HSW –75HSWV G5225–89064–75HSWV
–75HTW G5225–89064–75HTW –75HTWV G5225–89064–75HTWV
–80HN G5225–89064–80HN –80HNV G5225–89064–80HNV
–80HR G5225–89064–80HR –80HRV G5225–89064–80HRV
–80HS G5225–89064–80HS –80HSV G5225–89064–80HSV
–80HT G5225–89064–80HT –80HTV G5225–89064–80HTV
–80HNW G5225–89064–80HNW –80HNWV G5225–89064–80HNWV
–80HRW G5225–89064–80HRW –80HRWV G5225–89064–80HRWV
–80HSW G5225–89064–80HSW –80HSWV G5225–89064–80HSWV
–80HTW G5225–89064–80HTW –80HTWV G5225–89064–80HTWV
–85HN G5225–89064–85HN –85HNV G5225–89064–85HNV
–85HR G5225–89064–85HR –85HRV G5225–89064–85HRV
–85HS G5225–89064–85HS –85HSV G5225–89064–85HSV
–85HT G5225–89064–85HT –85HTV G5225–89064–85HTV
See footnotes at end of table.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 21
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
Vendor
CAGE Vendor name and address
–85HNW G5225–89064–85HNW –85HNWV G5225–89064–85HNWV
–85HRW G5225–89064–85HRW –85HRWV G5225–89064–85HRWV 5BG68 American Circuit Card Retainers, Inc.
2310 E. Orangethorpe Avenue
Anaheim, CA 92806–1231
–85HSW G5225–89064–85HSW –85HSWV G5225–89064–85HSWV
–85HTW G5225–89064–85HTW –85HTWV G5225–89064–85HTWV
Telephone: (714) 738–6194
Facsimile: (714) 446–0119
E-mail: sales@accrmfg.com
URL: http://www.accrmfg.com
(1) Parts must be purchased to this DESC PIN to assure that all performance requirements and inspections are met.
(2) Do not use vendor PIN's for acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing.
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2) (3)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2) (3)
Vendor
CAGE Vendor name and address
–50AN 40–5–10–A –50ANV 40–5VI–10–A
–50AR 40–5–10–R –50ARV 40–5VI–10–R 61081
Pentair Technical Products
(formerly Birtcher)
7328 Trade Street
San Diego, CA 92121–3410
–50AS 40–5–10 –50ASV 40–5VI–10
–50AT 40–5–10–T –50ATV 40–5VI–10–T
–50ANW 40–5–10–LF–A –50ANWV 40–5VI–10–LF–A
–50ARW 40–5–10–LF–R –50ARWV 40–5VI–10–LF–R Telephone: (858) 740–2400
–50ASW 40–5–10–LF –50ASWV 40–5VI–10–LF Facsimile: (858) 740–2430
–50ATW 40–5–10–LF–T –50ATWV 40–5VI–10–LF–T
–50BN 42–5–10–A –50BNV 42–5VI–10–A E-mail: schroff.us@pentair.com
–50BR 42–5–10–R –50BRV 42–5VI–10–R
–50BS 42–5–10 –50BSV 42–5VI–10 URL: http://schroff.pentair.com
–50BT 42–5–10–T –50BTV 42–5VI–10–T
–50BNW 42–5–10–LF–A –50BNWV 42–5VI–10–LF–A
–50BRW 42–5–10–LF–R –50BRWV 42–5VI–10–LF–R
–50BSW 42–5–10–LF –50BSWV 42–5VI–10–LF
–50BTW 42–5–10–LF–T –50BTWV 42–5VI–10–LF–T
–50CN 40–5–1013–A –50CNV 40–5VI–1013–A
–50CR 40–5–1013–R –50CRV 40–5VI–1013–R
–50CS 40–5–1013 –50CSV 40–5VI–1013
–50CT 40–5–1013–T –50CTV 40–5VI–1013–T
–50CNW 40–5–1013–LF–A –50CNWV 40–5VI–1013–LFA
–50CRW 40–5–1013–LF–R –50CRWV 40–5VI–1013–LFR
–50CSW 40–5–1013–LF –50CSWV 40–5VI–1013–LF
See footnotes at end of table.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 22
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2) (3)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2) (3)
Vendor
CAGE Vendor name and address
–50CTW 40–5–1013–LF–T –50CTWV 40–5VI–1013–LFT
–60AN 40–5–12–A –60ANV 40–5VI–12–A 61081
Pentair Technical Products
(formerly Birtcher)
7328 Trade Street
San Diego, CA 92121–3410
–60AR 40–5–12–R –60ARV 40–5VI–12–R
–60AS 40–5–12 –60ASV 40–5VI–12
–60AT 40–5–12–T –60ATV 40–5VI–12–T
–60ANW 40–5–12–LF–A –60ANWV 40–5VI–12–LF–A Telephone: (858) 740–2400
–60ARW 40–5–12–LF–R –60ARWV 40–5VI–12–LF–R Facsimile: (858) 740–2430
–60ASW 40–5–12–LF –60ASWV 40–5VI–12–LF
–60ATW 40–5–12–LF–T –60ATWV 40–5VI–12–LF–T E-mail: schroff.us@pentair.com
–60BN 42–5–12–A –60BNV 42–5VI–12–A
–60BR 42–5–12–R –60BRV 42–5VI–12–R URL: http://schroff.pentair.com
–60BS 42–5–12 –60BSV 42–5VI–12
–60BT 42–5–12–T –60BTV 42–5VI–12–T
–60BNW 42–5–12–LF–A –60BNWV 42–5VI–12–LF–A
–60BRW 42–5–12–LF–R –60BRWV 42–5VI–12–LF–R
–60BSW 42–5–12–LF –60BSWV 42–5VI–12–LF
–60BTW 42–5–12–LF–T –60BTWV 42–5VI–12–LF–T
–60CN 40–5–12–A –60CNV 40–5VI–12–A
–60CR 40–5–1108–R –60CRV 40–5VI–1108–R
–60CS 40–5–1108 –60CSV 40–5VI–1108
–60CT 40–5–1108–T –60CTV 40–5VI–1108–T
–60CNW 40–5–12–LF–A –60CNWV 40–5VI–12–LF–A
–60CRW 40–5–1108–LF–R –60CRWV 40–5VI–1108–LFR
–60CSW 40–5–1108–LF –60CSWV 40–5VI–1108–LF
–60CTW 40–5–1108–LF–T –60CTWV 40–5VI–1108–LFT
–65BN 42–5–13–A –65BNV 42–5VI–13–A
–65BR 42–5–13–R –65BRV 42–5VI–13–R
–65BS 42–5–13 –65BSV 42–5VI–13
–65BT 42–5–13–T –65BTV 42–5VI–13–T
–65BNW 42–5–13–LF–A –65BNWV 42–5VI–13–LF–A
–65BRW 42–5–13–LF–R –65BRWV 42–5VI–13–LF–R
–65BSW 42–5–13–LF –65BSWV 42–5VI–13–LF
–65BTW 42–5–13–LF–T –65BTWV 42–5VI–13–LF–T
–65CN 40–5–13–A –65CNV 40–5VI–13–A
–65CR 40–5–1109–R –65CRV 40–5VI–1109–R
–65CS 40–5–1109 –65CSV 40–5VI–1109
–65CT 40–5–1109–T –65CTV 40–5VI–1109–T
–65CNW 40–5–13–LF–A –65CNWV 40–5VI–13–LF–A
–65CRW 40–5–1109–LFR –65CRWV 40–5VI–1109–LFR
–65CSW 40–5–1109–LF –65CSWV 40–5VI–1109–LF
See footnotes at end of table.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 23
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2) (3)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2) (3)
Vendor
CAGE Vendor name and address
–65CTW 40–5–1109–LF–T –65CTWV 40–5VI–1109–LFT
–70DN 40–5–14–A –70DNV 40–5VI–14–A 61081
Pentair Technical Products
(formerly Birtcher)
7328 Trade Street
San Diego, CA 92121–3410
–70DR 40–5–14–R –70DRV 40–5VI–14–R
–70DS 40–5–14 –70DSV 40–5VI–14
–70DT 40–5–14–T –70DTV 40–5VI–14–T
–70DNW 40–5–14–LF–A –70DNWV 40–5VI–14–LF–A Telephone: (858) 740–2400
–70DRW 40–5–14–LF–R –70DRWV 40–5VI–14–LF–R Facsimile: (858) 740–2430
–70DSW 40–5–14–LF –70DSWV 40–5VI–14–LF
–70DTW 40–5–14–LF–T –70DTWV 40–5VI–14–LF–T E-mail: schroff.us@pentair.com
–75DN 40–5–15–A –75BNV 40–5VI–15–A
–75DR 40–5–15–R –75DRV 40–5VI–15–R URL: http://schroff.pentair.com
–75DS 40–5–15 –75DSV 40–5VI–15
–75DT 40–5–15–T –75DTV 40–5VI–15–T
–75DNW 40–5–15–LF–A –75DNWV 40–5VI–15–LF–A
–75DRW 40–5–15–LF–R –75DRWV 40–5VI–15–LF–R
–75DSW 40–5–15–LF –75DSWV 40–5VI–15–LF
–75DTW 40–5–15–LF–T –75DTWV 40–5VI–15–LF–T
–80DN 40–5–16–A –80DNV 40–5VI–16–A
–80DR 40–5–16–R –80DRV 40–5VI–16–R
–80DS 40–5–16 –80DSV 40–5VI–16
–80DT 40–5–16–T –80DTV 40–5VI–16–T
–80DNW 40–5–16–LF–A –80DNWV 40–5VI–16–LF–A
–80DRW 40–5–16–LF–R –80DRWV 40–5VI–16–LF–R
–80DSW 40–5–16–LF –80DSWV 40–5VI–16–LF
–80DTW 40–5–16–LF–T –80DTWV 40–5VI–16–LF–T
–85DN 40–5–17–A –85DNV 40–5VI–17–A
–85DR 40–5–17–R –85DRV 40–5VI–17–R
–85DS 40–5–17 –85DSV 40–5VI–17
–85DT 40–5–17–T –85DTV 40–5VI–17–T
–85DNW 40–5–17–LF–A –85DNWV 40–5VI–17–LF–A
–85DRW 40–5–17–LF–R –85DRWV 40–5VI–17–LF–R
–85DSW 40–5–17–LF –85DSWV 40–5VI–17–LF
–85DTW 40–5–17–LF–T –85DTWV 40–5VI–17–LF–T
(1) Parts must be purchased to this DESC PIN to assure that all performance requirements and inspections are met.
(2) Do not use vendor PIN's for acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing.
(3) CAGE 61081 card holders are supplied assembled.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 24
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
Vendor
CAGE Vendor name and address
–50EN 226–1006–4.80 –50ENV V226–1006–4.80
–50ER 226–1006–4.80H –50ERV V226–1006–4.80H 61081 Pentair Technical Products
(formerly Calmark)
7328 Trade Street
San Diego, CA 92121–3410
–50ES 226–1006–4.80T2 –50ESV V226–1006–4.80T2
–50ET 226–1006–4.80T0 –50ETV V226–1006–4.80T0
–50ENW W226–1006–4.80 –50ENWV WV226–1006–4.80
–50ERW W226–1006–4.80H –50ERWV WV226–1006–4.80H Telephone: (858) 740–2400
–50ESW W226–1006–4.80T2 –50ESWV WV226–1006–4.80T2 Facsimile: (858) 740–2430
–50ETW W226–1006–4.80T0 –50ETWV WV226–1006–4.80T0
–50FN 231–1013–4.80 –50FNV V231–1006–4.80 E-mail: schroff.us@pentair.com
–50FR 231–1013–4.80H –50FRV V231–1006–4.80H
–50FS 231–1013–4.80T2 –50FSV V231–1006–4.80T2 URL: http://schroff.pentair.com
–50FT 231–1013–4.80T0 –50FTV V231–1006–4.80T0
–50FNW W231–1013–4.80 –50FNWV WV231–1006–4.80
–50FRW W231–1013–4.80H –50FRWV WV231–1006–4.80H
–50FSW W231–1013–4.80T2 –50FSWV WV231–1006–4.80T2
–50FTW W231–1013–4.80T0 –50FTWV WV231–1006–4.80T0
–50GN 226–1007–4.80 –50GNV V226–1007–4.80
–50GR 226–1007–4.80H –50GRV V226–1007–4.80H
–50GS 226–1007–4.80T2 –50GSV V226–1007–4.80T2
–50GT 226–1007–4.80T0 –50GTV V226–1007–4.80T0
–50GNW W226–1007–4.80 –50GNWV WV226–1007–4.80
–50GRW W226–1007–4.80H –50GRWV WV226–1007–4.80H
–50GSW W226–1007–4.80T2 –50GSWV WV226–1007–4.80T2
–50GTW W226–1007–4.80T0 –50GTWV WV226–1007–4.80T0
–60EN 226–1006–5.80 –60ENV V226–1006–5.80
–60ER 226–1006–5.80H –60ERV V226–1006–5.80H
–60ES 226–1006–5.80T2 –60ESV V226–1006–5.80T2
–60ET 226–1006–5.80T0 –60ETV V226–1006–5.80T0
–60ENW W226–1006–5.80 –60ENWV WV226–1006–5.80
–60ERW W226–1006–5.80H –60ERWV WV226–1006–5.80H
–60ESW W226–1006–5.80T2 –60ESWV WV226–1006–5.80T2
–60ETW W226–1006–5.80T0 –60ETWV WV226–1006–5.80T0
–60FN 231–1013–5.80 –60FNV V231–1006–5.80
–60FR 231–1013–5.80H –60FRV V231–1006–5.80H
–60FS 231–1013–5.80T2 –60FSV V231–1006–5.80T2
–60FT 231–1013–5.80T0 –60FTV V231–1006–5.80T0
–60FNW W231–1013–5.80 –60FNWV WV231–1006–5.80
–60FRW W231–1013–5.80H –60FRWV WV231–1006–5.80H
–60FSW W231–1013–5.80T2 –60FSWV WV231–1006–5.80T2
–60FTW W231–1013–5.80T0 –60FTWV WV231–1006–5.80T0
See footnotes at end of table.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 25
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
Vendor
CAGE Vendor name and address
–60GN 226–1007–5.80 –60GNV V226–1007–5.80
–60GR 226–1007–5.80H –60GRV V226–1007–5.80H 61081
Pentair Technical Products
(formerly Calmark)
7328 Trade Street
San Diego, CA 92121–3410
–60GS 226–1007–5.80T2 –60GSV V226–1007–5.80T2
–60GT 226–1007–5.80T0 –60GTV V226–1007–5.80T0
–60GNW W226–1007–5.80 –60GNWV WV226–1007–5.80
–60GRW W226–1007–5.80H –60GRWV WV226–1007–5.80H Telephone: (858) 740–2400
–60GSW W226–1007–5.80T2 –60GSWV WV226–1007–5.80T2 Facsimile: (858) 740–2430
–60GTW W226–1007–5.80T0 –60GTWV WV226–1007–5.80T0
–65EN 226–1006–6.30 –65ENV V226–1006–6.30 E-mail: schroff.us@pentair.com
–65ER 226–1006–6.30H –65ERV V226–1006–6.30H
–65ES 226–1006–6.30T2 –65ESV V226–1006–6.30T2 URL: http://schroff.pentair.com
–65ET 226–1006–6.30T0 –65ETV V226–1006–6.30T0
–65ENW W226–1006–6.30 –65ENWV WV226–1006–6.30
–65ERW W226–1006–6.30H –65ERWV WV226–1006–6.30H
–65ESW W226–1006–6.30T2 –65ESWV WV226–1006–6.30T2
–65ETW W226–1006–6.30T0 –65ETWV WV226–1006–6.30T0
–65FN 231–1013–6.30 –65FNV V231–1013–6.30
–65FR 231–1013–6.30H –65FRV V231–1013–6.30H
–65FS 231–1013–6.30T2 –65FSV V231–1013–6.30T2
–65FT 231–1013–6.30T0 –65FTV V231–1013–6.30T0
–65FNW W231–1013–6.30 –65FNWV WV231–1013–6.30
–65FRW W231–1013–6.30H –65FRWV WV231–1013–6.30H
–65FSW W231–1013–6.30T2 –65FSWV WV231–1013–6.30T2
–65FTW W231–1013–6.30T0 –65FTWV WV231 1013 6.30T0
–65GN 226–1007–6.30 –65GNV V226–1007–6.30
–65GR 226–1007–6.30H –65GRV V226–1007–6.30H
–65GS 226–1007–6.30T2 –65GSV V226–1007–6.30T2
–65GT 226–1007–6.30T0 –65GTV V226–1007–6.30T0
–65GNW W226–1007–6.30 –65GNWV WV226–1007–6.30
–65GRW W226–1007–6.30H –65GRWV WV226–1007–6.30H
–65GSW W226–1007–6.30T2 –65GSWV WV226–1007–6.30T2
–65GTW W226–1007–6.30T0 –65GTWV WV226–1007–6.30T0
–70HN 226–1084–6.80 –70HNV V226–1084–6.80
–70HR 226–1084–6.80H –70HRV V226–1084–6.80H
–70HS 226–1084–6.80T2 –70HSV V226–1084–6.80T2
–70HT 226–1084–6.80T0 –70HTV V226–1084–6.80T0
–70HNW W226–1084–6.80 –70HNWV WV226–1084–6.80
–70HRW W226–1084–6.80H –70HRWV WV226–1084–6.80H
–70HSW W226–1084–6.80T2 –70HSWV WV226–1084–6.80T2
–70HTW W226–1084–6.80T0 –70HTWV WV226–1084–6.80T0
See footnotes at end of table.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 454 44
SIZE
CAGE CODE DWG NO.
A
14933
89064
REV G PAGE 26
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
DESC
drawing PIN
89064 (1)
Vendor similar
designation or type
number (2)
Vendor
CAGE Vendor name and address
–75HN 226–1084–7.30 –75HNV V226–1084–7.30
–75HR 226–1084–7.30H –75HRV V226–1084–7.30H 61081
Pentair Technical Products
(formerly Calmark)
7328 Trade Street
San Diego, CA 92121–3410
–75HS 226–1084–7.30T2 –75HSV V226–1084–7.30T2
–75HT 226–1084–7.30T0 –75HTV V226–1084–7.30T0
–75HNW W226–1084–7.30 –75HNWV WV226–1084–7.30
–75HRW W226–1084–7.30H –75HRWV WV226–1084–7.30H
Telephone: (858) 740–2400
–75HSW W226–1084–7.30T2 –75HSWV WV226–1084–7.30T2 Facsimile: (858) 740–2430
–75HTW W226–1084–7.30T0 –75HTWV WV226–1084–7.30T0
–80HN 226–1085–7.80 –80HNV V226–1085–7.80 E-mail: schroff.us@pentair.com
–80HR 226–1085–7.80H –80HRV V226–1085–7.80H
–80HS 226–1085–7.80T2 –80HSV V226–1085–7.80T2 URL: http://schroff.pentair.com
–80HT 226–1085–7.80T0 –80HTV V226–1085–7.80T0
–80HNW W226–1085–7.80 –80HNWV WV226–1085–7.80
–80HRW W226–1085–7.80H –80HRWV WV226–1085–7.80H
–80HSW W226–1085–7.80T2 –80HSWV WV226–1085–7.80T2
–80HTW W226–1085–7.80T0 –80HTWV WV226–1085–7.80T0
–85HN 226–1085–8.30 –85HNV V226–1085–8.30
–85HR 226–1085–8.30H –85HRV V226–1085–8.30H
–85HS 226–1085–8.30T2 –85HSV V226–1085–8.30T2
–85HT
226–1085–8.30T0
–85HTV
V226–1085–8.30T0
–85HNW W226–1085–8.30 –85HNWV WV226–1085–8.30
–85HRW W226–1085–8.30H –85HRWV WV226–1085–8.30H
–85HSW
W226–1085–8.30T2
–85HSWV
WV226–1085–8.30T2
–85HTW W226–1085–8.30T0 –85HTWV WV226–1085–8.30T0
(1) Parts must be purchased to this DESC PIN to assure that all performance requirements and inspections are met.
(2) Do not use vendor PIN's for acquisition.
