REVISIONS LTR DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5998-R005-95 28 June 1996 John F. Raye B Add new configurations D and E. Change FSC from 5999 to 5998. Editorial changes throughout. 22 May 2000 Monica L. Poelking C Corrected inaccuracies in all configurations. 7 SEP 2001 Thomas M. Hess D Section 2 updated to remove cancelled documents and add the superseding replacements. Corrected supersession data. Added an additional supplier. Editorial changes throughout. 20 SEP 2002 Thomas M. Hess E Corrected inaccuracies in configurations D, E, F, G, and H. Editorial changes throughout. 24 OCT 2003 Thomas M. Hess F Corrected inaccuracies in configurations A, B, C, and D. 6 JUN 2014 Thomas M. Hess G Update material requirements for alignment springs. 24 OCT 2016 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME, COLUMBUS, OHIO 43218-3990 Notice of Partial Inactivation for New Design The PINs identified in see 6.6 are INACTIVE FOR NEW DESIGN AFTER 6 June 2014 FOR NEW DESIGN USE CID A-A-59789 Prepared in accordance with ASME Y14.100 REV G G G G G G G PAGE 16 17 18 19 20 21 22 23 24 25 26 REV G G G G G G G G G G G G G G G PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 REV STATUS OF PAGES DESIGN ACTIVITY PREPARED BY PMIC N/A Original date of drawing DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 Bernard J. Miesse CHECKED BY TITLE HOLDER, ELECTRICAL CARD, WEDGE RETAINER, 5 PIECE, .225 INCH BY .225 INCH AND .225 INCH BY .260 INCH BODY SIZE David J. Corbett 8 November 1989 APPROVED BY Monica L. Poelking SIZE A AMSC N/A CAGE CODE 14933 REV G 89064 DWG. NO. PAGE 1 OF 26 5998-2016-E086 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of 5 wedge metal card-retainers intended to hold circuit card assemblies or printed wiring assemblies in their installed positions. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example: 89064 Drawing number -50 Dash number (see table I) A Configuration (see 3.1 and figure 1) N Mounting options (see 3.1.1 and table II) WV Other options (see 3.1.2) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-DTL-5002 MIL-DTL-5541 - - Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapon Systems. Chemical Conversion Coatings On Aluminum And Aluminum Alloys. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http://quicksearch.dla.mil.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. AIA/NAS NAS 620 AIA/NAS NASM35338 AIA/NAS NASM122116-122155 - - - Washer, Flat, Reduced Outside Diameter. Washer, Lock-Spring, Helical, Regular (Medium) Series. Insert, CRES Helical Coil, Coarse Thread, 1-1/2 Dia. Nominal Length. (Copies of these documents are available online at http://www.aia-aerospace.org or from the Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209-3901.) DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 2 ASTM INTERNATIONAL (ASTM) ASTM A484/A484M - ASTM A582/582M ASTM B194 ASTM B221 - - - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings. Standard Specification for Free-Machining Stainless Steel Bars. Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar. Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles and Tubes. (Copies of these documents are available online at http://www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SAE INTERNATIONAL (SAE) SAE AMS-QQ-N-290 SAE AMS-QQ-S-763 SAE AMS 5518 - - - SAE AMS 5904 - Nickel Plating (Electrodeposited) Steel, Corrosion Resistant, Bars, Wire, Shapes, and Forgings Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni Cold Rolled, 150 ksi (1034 MPa) Tensile Strength Steel, Corrosion-Resistant, Sheet and Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled 1/2 Hard, 150ksi (1034 MPa) Tensile Strength (Copies of these documents are available online at http://www.sae.org or from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. See tables I and II and figure 1. Some card holders conforming to this drawing may be supplied in a unassembled condition. See 6.8 for additional information. 3.1.1 Mounting to circuit card assembly. Card holders conforming to this drawing are secured to the circuit card assembly using either adhesives, brazing, fastener, or rivets. Card holders are available either with mounting holes as shown on figure 1 or without mounting holes. There are three options for designs with mounting holes. The hole options are counterbore holes or two styles of tapped holes. 3.1.1.1 No mounting holes (for adhesive or brazing mounting). Card holders without mounting holes (to facilitate adhesive or brazing mounting) shall contain an "N" in the PIN. 3.1.1.2 Counterbore holes (for rivet mounting). Counterbore holes shall be .068/.073 inch (1.73/1.85 mm) diameter countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with an access/clearance hole .156 inch (3.96) diameter by .200 inch (5.08 mm) deep for configurations "A", "C", "D", and "E" and .175 inch (4.45 mm) deep for configuration "B". Card retainers with counterbore holes shall include a suffix "R" in the PIN. 3.1.1.3 Tapped holes (for threaded fasteners). Card retainers with 2-56 UNF tapped through holes shall include a suffix "S" in the PIN. Card retainers with 0-80 UNF tapped through holes shall include a suffix "T" in the PIN (see figure 1, table I, and 1.2). 3.1.2 Alignment springs. Configurations "A", "B", "C", and "D" that have no mounting holes or tapped mounting holes shall have 3 alignment springs, one in the mounting body and one in each of the two intermediate bodies. Configurations "A", "B", "C", and "D" that use rivets for mounting holes shall have 2 alignment springs, one in each of the two intermediate bodies. The mounting body will not have an alignment spring. Configurations "E", "F", "G", and "H" shall have 3 alignment springs, one in the mounting body and one in each of the two intermediate bodies for all mounting options. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 3 3.1.3 Optional features. 3.1.3.1 Flat washer and lockwasher. A flat washer and lockwasher feature are available (see figure 1 and table I). Card retainers with the optional flat washer and lockwasher feature shall include a suffix "W" in the PIN (see figure 1 and 1.2). 3.1.3.2 Visual lock indication. An optional visual lock indication feature is available (see figure 1 and table I). Card retainers with the optional visual lock indication shall include a suffix "V" in the PIN (see figure 1 and 1.2). TABLE I. Card retainer dimensions and configurations. 1/ 2/ PIN 89064 1/ 2/ Configuration Dimension "L" (length) +.02 / -.03 (+0.5 / -0.8 mm) Dimension "A" (mounting body) .01 (0.3 mm) Dimension "B" (mounting hole) .02 (0.5 mm) Dimension "C" Number of mounting holes -50 A, E 5.00 (127.0) 1.50 (38.1) .30 (7.6) 1.15 (29.2) 2 -50 B, F 5.00 (127.0) 1.50 (38.1) .30 (7.6) 1.15 (29.2) 2 -50 C, G 5.00 (127.0) 1.50 (38.1) .50 (12.7) 1.15 (29.2) 2 -60 A, E 6.00 (152.4) 2.50 (63.5) .80 (20.3) 1.15 (29.2) 2 -60 B, F 6.00 (152.4) 2.50 (63.5) .80 (20.3) 1.15 (29.2) 2 -60 C, G 6.00 (152.4) 2.50 (63.5) 1.00 (25.4) 1.15 (29.2) 2 -65 A, E 6.50 (165.1) 3.00 (76.2) 1.05 (26.7) 1.15 (29.2) 2 -65 B, F 6.50 (165.1) 3.00 (76.2) 1.05 (26.7) 1.15 (29.2) 2 -65 C, G 6.50 (165.1) 3.00 (76.2) 1.25 (26.7) 1.15 (29.2) 2 -70 D, H 7.00 (177.8) 3.50 (88.9) .40 (10.2) 1.15 (29.2) 4 -75 D, H 7.50 (190.5) 4.00 (101.6) .65 (16.5) 1.15 (29.2) 4 -80 D, H 8.00 (203.2) 3.50 (88.9) .40 (10.2) 1.65 (41.9) 4 -85 D, H 8.50 (215.9) 4.00 (101.6) .65 (16.5) 1.65 (41.9) 4 Dimensions are in inches. Metric equivalents are given for general information only. Tolerances, unless otherwise specified, are .02 inch (0.5 mm), for 2 place decimals and .010 inch (0.25 mm), for 3 place decimals. TABLE II. Mounting design. PIN modifier Attribute N Without mounting holes R Counterbore holes S 2-56 UNC tapped holes T 0-80 UNF tapped holes 3.2 Materials. 3.2.1 Alignment spring. The alignment spring shall be either beryllium copper in accordance with ASTM B194 or equivalent, or stainless steel in accordance with SAE AMS 5518, SAE AMS 5904, or equivalent. 3.2.2 Bodies and wedges. The bodies (mounting and intermediate) and wedges material shall be aluminum alloy in accordance with ASTM B221 or equivalent. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 4 3.2.3 Flatwasher. The flatwasher (included with the locking feature) shall comply with AIA/NAS NAS 620 or equivalent. 3.2.4 Lockwasher. The lockwasher (included with the locking feature) shall comply with AIA/NAS NASM35338-135 or equivalent. 3.2.5 Screw. The screw material shall be stainless steel in accordance with SAE AMS-QQ-S-763, ASTM A484/A484M, or ASTM A582/582M or equivalent. 3.2.6 Screw retention. 3.2.6.1 Captive nut. When a captive nut is used, the captive nut material shall be stainless steel, type 303, in accordance with ASTM A582/582M. 3.2.6.2 Helical insert. When a helical insert is used, the helical insert shall be in accordance with AIA/NAS NASM122116. 3.2.7 Visual indicator. 3.2.7.1 Cup. The cup material for visual indicators shall stainless steel in accordance with ASTM B194, SAE AMS 5904, or equivalent. 3.2.7.2 Spring. The spring material for visual indicators shall be stainless steel. 3.3 Finish. 3.3.1 Alignment spring. Stainless steel alignment springs shall be passivate in accordance with MIL-DTL-5002. Beryllium copper alignment springs shall be nickel plate in accordance with SAE AMS-QQ-N-290, class 1, grade G, bright (see 6.1.1 regarding nickel plating). 3.3.2 Bodies and wedges. The bodies and wedges shall be chemical finish in accordance with MIL-DTL-5541, class 1A. 3.3.3 Flatwasher, lockwasher, captive nut, helical insert, and screw. The flatwasher, lockwasher, captive nut, helical insert, and screw shall be passivate in accordance with MIL-DTL-5002. 3.3.4 Visual lock cup and spring (when applicable). The visual lock cup and spring shall be passivate in accordance with MIL-DTL-5002. 3.4 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in 6.8. The certificate of compliance, submitted to DLA Land and Maritime VAC prior to listing as an approved source of supply, shall state that the manufacturer's product meets the requirements herein. 3.5 Optional statement of compliance in lieu of performing conformance inspections. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery tests (see 4.2.2 and 6.2.b). 3.6 Marking. Marking of the card holder is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturer's name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Card holders shall be free from surface and finish flaws that affect life or serviceability. Card holders shall be finished smooth and shall have rounded edges with no evidence of chipping, cracking, deterioration, disintegration, or burrs. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 5 Inches mm Inches mm Inches mm Inches mm Inches mm .010 .06 0.25 1.5 .09 .14 2.3 3.6 .165 .20 4.19 5.1 .225 .260 .33 5.72 6.61 8.4 .330 .50 .900 8.38 12.7 22.86 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See 3.1.2 for requirements for the number of alignment springs and their placement. 4. See table I for L, A, B, and C dimensions and tolerances. FIGURE 1. Card holder dimensions and configurations. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 6 Inches mm Inches mm Inches mm Inches mm Inches mm .010 .06 0.25 1.5 .09 .14 2.3 3.6 .165 .20 4.19 5.1 .225 .275 .290 5.72 6.98 7.37 .33 .50 .900 8.4 12.7 22.86 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See 3.1.2 for requirements for the number of alignment springs and their placement. 4. See table I for L, A, B, and C dimensions and tolerances. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 7 Inches mm Inches mm Inches mm Inches mm Inches mm .010 .06 0.25 1.5 .09 .14 2.3 3.6 .165 .20 .225 4.19 5.1 5.72 .260 .33 .330 6.61 8.4 8.38 .50 .500 .900 12.7 12.70 22.86 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See 3.1.2 for requirements for the number of alignment springs and their placement. 4. See table I for L, A, B, and C dimensions and tolerances. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 8 Inches mm Inches mm Inches mm Inches mm Inches mm .005 .06 .09 0.13 1.5 2.3 .14 .165 .20 3.6 4.19 5.1 .225 .260 .33 5.72 6.61 8.4 .330 .50 .900 8.38 12.7 22.86 1.800 2.700 45.72 68.58 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See 3.1.2 for requirements for the number of alignment springs and their placement. 4. See table I for L, A, B, and C dimensions and tolerances. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 9 Inches mm Inches mm Inches mm Inches mm Inches mm .005 .06 0.13 1.5 .09 .165 2.3 4.19 .20 .225 .235 5.1 5.72 5.97 .270 .325 .33 6.86 8.36 8.4 .330 .50 .900 8.38 12.7 22.86 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See table I for L, A, B, and C dimensions and tolerances. 4. Screw advance is .14 inch (3.6 mm) maximum for card holders without the visual indicator and .31 inch (7.9 mm) maximum on card holders with the visual indicator option. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 10 Inches mm Inches mm Inches mm Inches mm Inches mm .005 .06 0.13 1.5 .09 .165 2.3 4.19 .20 .225 5.1 5.72 .235 .275 5.97 6.99 .33 .50 .900 8.4 12.7 22.86 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See table I for L, A, B, and C dimensions and tolerances. 4. Screw advance is .14 inch (3.6 mm) maximum for card holders without the visual indicator and .31 inch (7.9 mm) maximum on card holders with the visual indicator option. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 11 Inches mm Inches mm Inches mm Inches mm Inches mm .005 .06 0.13 1.5 .09 .165 2.3 4.19 .20 .225 5.1 5.72 .235 .270 .325 5.97 6.86 8.26 .33 .50 .500 8.4 12.7 12.70 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See table I for L, A, B, and C dimensions and tolerances. 4. Screw advance is .14 inch (3.6 mm) maximum for card holders without the visual indicator and .31 inch (7.9 mm) maximum on card holders with the visual indicator option. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 12 Inches mm Inches mm Inches mm Inches mm Inches mm .005 .06 .09 0.13 1.5 2.3 .165 .20 4.19 5.1 .225 .235 .270 5.72 5.97 6.86 .325 .33 .50 8.26 8.4 12.7 .900 1.800 2.700 22.86 45.72 68.58 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm), for 2 places and .010 inch (0.25 mm), for 3 places. 3. See table I for L, A, B, and C dimensions and tolerances. 4. Screw advance is .14 inch (3.6 mm) maximum for card holders without the visual indicator and .31 inch (7.9 mm) maximum on card holders with the visual indicator option. FIGURE 1. Card holder dimensions and configurations - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 13 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified in the contract or order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use their own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.8). Criteria for defects are listed in 4.2.1.3. 4.2.1.1 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.2.1.3. TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 29 35 10,001 and over 4.2.1.2 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.2.1.3 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. 4.2.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military Department or Defense Agency, or within the Military Department's System Command. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 14 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use when performance specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.1.1 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http://www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see 3.2). 6.1.2 Guidance on use of alternative parts with less hazardous or nonhazardous materials. This drawing provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. 6.2 Acquisition requirements. The acquisition requirements should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the product for delivery inspection (4.2.1) or provides an optional statement of compliance (4.2.2). d. Requirements for notification of change in product to the contracting activity, if applicable. e. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail at 5998.Documents@dla.mil or by facsimile (614) 692-6939 or DSN 850-6939. 6.4 Replaceability. Retainers covered herein replace similar commercial devices covered by contractor-prepared specifications or drawings. 6.5 Changes from previous issue. Asterisks are not used in this revision to identify changes with respect to the previous revision, due to the extensiveness of the changes. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 15 6.6 Supersession data concerning inactive for new design PINs. The inactive for new design part numbers with corresponding for new design use part numbers are listed below. Configurations "B", "C", "F", "G" and "H" have not been inactivated for new design and are not covered by A-A-59789. Superseded (old) part number Superseding (new) part number Superseded (old) part number Superseding (new) part number 89064-50AN 89064-50AR 89064-50AS 89064-50AT AA59789/21AC50N AA59789/21AC50R AA59789/21AC50S AA59789/21AC50T 89064-50ANW 89064-50ARW 89064-50ASW 89064-50ATW AA59789/21FC50N AA59789/21FC50R AA59789/21FC50S AA59789/21FC50T 89064-50EN 89064-50ER 89064-50ES 89064-50ET AA59789/21CC50N AA59789/21CC50R AA59789/21CC50S AA59789/21CC50T 89064-50ENW 89064-50ERW 89064-50ESW 89064-50ETW AA59789/21WC50N AA59789/21WC50R AA59789/21WC50S AA59789/21WC50T 89064-60AN 89064-60AR 89064-60AS 89064-60AT AA59789/21AC60N AA59789/21AC60R AA59789/21AC60S AA59789/21AC60T 89064-60ANW 89064-60ARW 89064-60ASW 89064-60ATW AA59789/21FC60N AA59789/21FC60R AA59789/21FC60S AA59789/21FC60T 89064-60EN 89064-65ER 89064-65ES 89064-65ET AA59789/21CC60N AA59789/21CC65R AA59789/21CC65S AA59789/21CC65T 89064-60ENW 89064-65ERW 89064-65ESW 89064-65ETW AA59789/21WC60N AA59789/21WC65R AA59789/21WC65S AA59789/21WC65T 89064-65AN 89064-65AR 89064-65AS 89064-65AT AA59789/21AC65N AA59789/21AC65R AA59789/21AC65S AA59789/21AC65T 89064-65ANW 89064-65ARW 89064-65ASW 89064-65ATW AA59789/21FC65N AA59789/21FC65R AA59789/21FC65S AA59789/21FC65T 89064-65EN 89064-65ER 89064-65ES 89064-65ET AA59789/21CC65N AA59789/21CC65R AA59789/21CC65S AA59789/21CC65T 89064-65ENW 89064-65ERW 89064-65ESW 89064-65ETW AA59789/21WC65N AA59789/21WC65R AA59789/21WC65S AA59789/21WC65T 89064-70AN 89064-70AR 89064-70AS 89064-70AT AA59789/23AC70N AA59789/23AC70R AA59789/23AC70S AA59789/23AC70T 89064-70ANW 89064-70ARW 89064-70ASW 89064-70ATW AA59789/23FC70N AA59789/23FC70R AA59789/23FC70S AA59789/23FC70T 89064-70EN 89064-70ER 89064-70ES 89064-70ET AA59789/23CC70N AA59789/23CC70R AA59789/23CC70S AA59789/23CC70T 89064-70ENW 89064-70ERW 89064-70ESW 89064-70ETW AA59789/23WC70N AA59789/23WC70R AA59789/23WC70S AA59789/23WC70T 89064-75AN 89064-75AR 89064-75AS 89064-75AT AA59789/23AC75N AA59789/23AC75R AA59789/23AC75S AA59789/23AC75T 89064-75ANW 89064-75ARW 89064-75ASW 89064-75ATW AA59789/23FC75N AA59789/23FC75R AA59789/23FC75S AA59789/23FC75T 89064-75EN 89064-75ER 89064-75ES 89064-75ET AA59789/23CC75N AA59789/23CC75R AA59789/23CC75S AA59789/23CC75T 89064-75ENW 89064-75ERW 89064-75ESW 89064-75ETW AA59789/23WC75N AA59789/23WC75R AA59789/23WC75S AA59789/23WC75T DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 16 Superseded (old) part number Superseding (new) part number Superseded (old) part number Superseding (new) part number 89064-80AN AA59789/23AC80N 89064-80ANW AA59789/23FC80N 89064-80AR AA59789/23AC80R 89064-80ARW AA59789/23FC80R 89064-80AS AA59789/23AC80S 89064-80ASW AA59789/23FC80S 89064-80AT AA59789/23AC80T 89064-80ATW AA59789/23FC80T 89064-80EN AA59789/23CC80N 89064-80ENW AA59789/23WC80N 89064-80ER AA59789/23CC80R 89064-80ERW AA59789/23WC80R 89064-80ES AA59789/23CC80S 89064-80ESW AA59789/23WC80S 89064-80ET AA59789/23CC80T 89064-80ETW AA59789/23WC80T 89064-85AN AA59789/23AC85N 89064-85ANW AA59789/23FC85N 89064-85AR AA59789/23AC85R 89064-85ARW AA59789/23FC85R 89064-85AS AA59789/23AC85S 89064-85ASW AA59789/23FC85S 89064-85AT AA59789/23AC85T 89064-85ATW AA59789/23FC85T 89064-85EN AA59789/23CC85N 89064-85ENW AA59789/23WC85N 89064-85ER AA59789/23CC85R 89064-85ERW AA59789/23WC85R 89064-85ES AA59789/23CC85S 89064-85ESW AA59789/23WC85S 89064-85ET AA59789/23CC85T 89064-85ETW AA59789/23WC85T 89064-60ANV AA59789/22AC60N 89064-60ANWV AA59789/22FC60N 89064-60ARV AA59789/22AC60R 89064-60ARWV AA59789/22FC60R 89064-60ASV AA59789/22AC60S 89064-60ASWV AA59789/22FC60S 89064-60ATV AA59789/22AC60T 89064-60ATWV AA59789/22FC60T 89064-60ENV AA59789/22CC60N 89064-60ENWV AA59789/22WC60N 89064-65ERV AA59789/22CC65R 89064-65ERWV AA59789/22WC65R 89064-65ESV AA59789/22CC65S 89064-65ESWV AA59789/22WC65S 89064-65ETV AA59789/22CC65T 89064-65ETWV AA59789/22WC65T 89064-65ANV AA59789/22AC65N 89064-65ANWV AA59789/22FC65N 89064-65ARV AA59789/22AC65R 89064-65ARWV AA59789/22FC65R 89064-65ASV AA59789/22AC65S 89064-65ASWV AA59789/22FC65S 89064-65ATV AA59789/22AC65T 89064-65ATWV AA59789/22FC65T 89064-65ENV AA59789/22CC65N 89064-65ENWV AA59789/22WC65N 89064-65ERV AA59789/22CC65R 89064-65ERWV AA59789/22WC65R 89064-65ESV AA59789/22CC65S 89064-65ESWV AA59789/22WC65S 89064-65ETV AA59789/22CC65T 89064-65ETWV AA59789/22WC65T 89064-70ANV AA59789/24AC70N 89064-70ANWV AA59789/24FC70N 89064-70ARV AA59789/24AC70R 89064-70ARWV AA59789/24FC70R 89064-70ASV AA59789/24AC70S 89064-70ASWV AA59789/24FC70S 89064-70ATV AA59789/24AC70T 89064-70ATWV AA59789/24FC70T 89064-70ENV AA59789/24CC70N 89064-70ENWV AA59789/24WC70N 89064-70ERV AA59789/24CC70R 89064-70ERWV AA59789/24WC70R 89064-70ESV AA59789/24CC70S 89064-70ESWV AA59789/24WC70S 89064-70ETV AA59789/24CC70T 89064-70ETWV AA59789/24WC70T DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 17 Superseded (old) part number Superseding (new) part number Superseded (old) part number Superseding (new) part number 89064-75ANV 89064-75ARV 89064-75ASV 89064-75ATV AA59789/24AC75N AA59789/24AC75R AA59789/24AC75S AA59789/24AC75T 89064-75ANWV 89064-75ARWV 89064-75ASWV 89064-75ATWV AA59789/24FC75N AA59789/24FC75R AA59789/24FC75S AA59789/24FC75T 89064-75ENV 89064-75ERV 89064-75ESV 89064-75ETV AA59789/24CC75N AA59789/24CC75R AA59789/24CC75S AA59789/24CC75T 89064-75ENWV 89064-75ERWV 89064-75ESWV 89064-75ETWV AA59789/24WC75N AA59789/24WC75R AA59789/24WC75S AA59789/24WC75T 89064-80ANV 89064-80ARV 89064-80ASV 89064-80ATV AA59789/24AC80N AA59789/24AC80R AA59789/24AC80S AA59789/24AC80T 89064-80ANWV 89064-80ARWV 89064-80ASWV 89064-80ATWV AA59789/24FC80N AA59789/24FC80R AA59789/24FC80S AA59789/24FC80T 89064-80ENV 89064-80ERV 89064-80ESV 89064-80ETV AA59789/24CC80N AA59789/24CC80R AA59789/24CC80S AA59789/24CC80T 89064-80ENWV 89064-80ERWV 89064-80ESWV 89064-80ETWV AA59789/24WC80N AA59789/24WC80R AA59789/24WC80S AA59789/24WC80T 89064-85ANV 89064-85ARV 89064-85ASV 89064-85ATV AA59789/24AC85N AA59789/24AC85R AA59789/24AC85S AA59789/24AC85T 89064-85ANWV 89064-85ARWV 89064-85ASWV 89064-85ATWV AA59789/24FC85N AA59789/24FC85R AA59789/24FC85S AA59789/24FC85T 89064-85ENV 89064-85ERV 89064-85ESV 89064-85ETV AA59789/24CC85N AA59789/24CC85R AA59789/24CC85S AA59789/24CC85T 89064-85ENWV 89064-85ERWV 89064-85ESWV 89064-85ETWV AA59789/24WC85N AA59789/24WC85R AA59789/24WC85S AA59789/24WC85T 6.7 Supersession data concerning previous revisions. The original issue of this drawing PIN did not contain a suffix to designate length, configuration, or other options. Superseded part numbers are listed below. New PIN 89064- Previous part number 89064- Previous part number 89064- New PIN 89064- Previous part number 89064- 50AN 01A 60ANV 07A 60BN 13A 50CNV 19A 50AS 50ANW 01M 60ASV 07M 60BS 13M 50CRV 19M 02A 60ANWV 08A 60BNW 14A 50CNWV 20A 50ASW 02M 60ASWV 08M 60BSW 14M 50CRWV 20M 50ANV 03A 50BN 09A 60BNV 15A 60CN 21A 50ASV 03M 50BS 09M 60BSV 15M 60CR 21M 50ANWV 04A 50BNW 10A 60BNWV 16A 60CNW 22A 50ASWV 04M 50BSW 10M 60BSWV 16M 60CRW 22M 60AN 05A 50BNV 11A 50CN 17A 60CNV 23A 60AS 05M 50BSV 11M 50CS 17M 60CRV 23M 60ANW 06A 50BNWV 12A 50CNW 18A 60CNWV 24A 60ASW 06M 50BSWV 12M 50CRW 18M 60CRWV 24M New PIN 89064- DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A New PIN 89064- CAGE CODE DWG NO. 89064 14933 REV Previous part number 89064- G PAGE 18 6.8 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed with this drawing and have submitted a certificate of compliance (see 3.4 herein) to DLA Land and Maritime, ATTN: VAC, Post Office Box 3990, Columbus, OH 43218-3990 or by electronic mail at "5998.Documents@dla.mil" or by facsimile (614) 692-6939 or DSN 850-6939. DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) -50EN G5225-89064-50EN -50ENV G5225-89064-50ENV -50ER G5225-89064-50ER -50ERV G5225-89064-50ERV Vendor CAGE Vendor name and address 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 92806-1231 -50ES G5225-89064-50ES -50ESV G5225-89064-50ESV -50ET G5225-89064-50ET -50ETV G5225-89064-50ETV -50ENW G5225-89064-50ENW -50ENWV G5225-89064-50ENWV -50ERW G5225-89064-50ERW -50ERWV G5225-89064-50ERWV Telephone: (714) 738-6194 -50ESW G5225-89064-50ESW -50ESWV G5225-89064-50ESWV Facsimile: (714) 446-0119 -50ETW G5225-89064-50ETW -50ETWV G5225-89064-50ETWV -50FN G5220-89064-50FN -50FNV G5220-89064-50FNV -50FR G5220-89064-50FR -50FRV G5220-89064-50FRV -50FS G5220-89064-50FS -50FSV G5220-89064-50FSV -50FT G5220-89064-50FT -50FTV G5220-89064-50FTV -50FNW G5220-89064-50FNW -50FNWV G5220-89064-50FNWV -50FRW G5220-89064-50FRW -50FRWV G5220-89064-50FRWV -50FSW G5220-89064-50FSW -50FSWV G5220-89064-50FSWV -50FTW G5220-89064-50FTW -50FTWV G5220-89064-50FTWV -60EN G5225-89064-60EN -60ENV G5225-89064-60ENV -60ER G5225-89064-60ER -60ERV G5225-89064-60ERV -60ES G5225-89064-60ES -60ESV G5225-89064-60ESV -60ET G5225-89064-60ET -60ETV G5225-89064-60ETV -60ENW G5225-89064-60ENW -60ENWV G5225-89064-60ENWV -60ERW G5225-89064-60ERW -60ERWV G5225-89064-60ERWV -60ESW G5225-89064-60ESW -60ESWV G5225-89064-60ESWV -60ETW G5225-89064-60ETW -60ETWV G5225-89064-60ETWV -60FN G5220-89064-60FN -60FNV G5220-89064-60FNV -60FR G5220-89064-60FR -60FRV G5220-89064-60FRV -60FS G5220-89064-60FS -60FSV G5220-89064-60FSV -60FT G5220-89064-60FT -60FTV G5220-89064-60FTV -60FNW G5220-89064-60FNW -60FNWV G5220-89064-60FNWV -60FRW G5220-89064-60FRW -60FRWV G5220-89064-60FRWV -60FSW G5220-89064-60FSW -60FSWV G5220-89064-60FSWV -60FTW G5220-89064-60FTW -60FTWV G5220-89064-60FTWV -65EN G5225-89064-65EN -65ENV G5225-89064-65ENV -65ER G5225-89064-65ER -65ERV G5225-89064-65ERV -65ES G5225-89064-65ES -65ESV G5225-89064-65ESV -65ET G5225-89064-65ET -65ETV G5225-89064-65ETV E-mail: sales@accrmfg.com URL: http://www.accrmfg.com See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 19 DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) Vendor CAGE Vendor name and address 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 92806-1231 -65ENW G5225-89064-65ENW -65ENWV G5225-89064-65ENWV -65ERW G5225-89064-65ERW -65ERWV G5225-89064-65ERWV -65ESW G5225-89064-65ESW -65ESWV G5225-89064-65ESWV -65ETW G5225-89064-65ETW -65ETWV G5225-89064-65ETWV -65FN G5220-89064-65FN -65FNV G5220-89064-65FNV -65FR G5220-89064-65FR -65FRV G5220-89064-65FRV Telephone: (714) 738-6194 -65FS G5220-89064-65FS -65FSV G5220-89064-65FSV Facsimile: (714) 446-0119 -65FT G5220-89064-65FT -65FTV G5220-89064-65FTV -65FNW G5220-89064-65FNW -65FNWV G5220-89064-65FNWV -65FRW G5220-89064-65FRW -65FRWV G5220-89064-65FRWV -65FSW G5220-89064-65FSW -65FSWV G5220-89064-65FSWV -65FTW G5220-89064-65FTW -65FTWV G5220-89064-65FTWV -70HN G5225-89064-70HN -70HNV G5225-89064-70HNV -70HR G5225-89064-70HR -70HRV G5225-89064-70HRV -70HS G5225-89064-70HS -70HSV G5225-89064-70HSV -70HT G5225-89064-70HT -70HTV G5225-89064-70HTV -70HNW G5225-89064-70HNW -70HNWV G5225-89064-70HNWV -70HRW G5225-89064-70HRW -70HRWV G5225-89064-70HRWV -70HSW G5225-89064-70HSW -70HSWV G5225-89064-70HSWV -70HTW G5225-89064-70HTW -70HTWV G5225-89064-70HTWV -75HN G5225-89064-75HN -75HNV G5225-89064-75HNV -75HR G5225-89064-75HR -75HRV G5225-89064-75HRV -75HS G5225-89064-75HS -75HSV G5225-89064-75HSV -75HT G5225-89064-75HT -75HTV G5225-89064-75HTV -75HNW G5225-89064-75HNW -75HNWV G5225-89064-75HNWV -75HRW G5225-89064-75HRW -75HRWV G5225-89064-75HRWV -75HSW G5225-89064-75HSW -75HSWV G5225-89064-75HSWV -75HTW G5225-89064-75HTW -75HTWV G5225-89064-75HTWV -80HN G5225-89064-80HN -80HNV G5225-89064-80HNV -80HR G5225-89064-80HR -80HRV G5225-89064-80HRV -80HS G5225-89064-80HS -80HSV G5225-89064-80HSV -80HT G5225-89064-80HT -80HTV G5225-89064-80HTV -80HNW G5225-89064-80HNW -80HNWV G5225-89064-80HNWV -80HRW G5225-89064-80HRW -80HRWV G5225-89064-80HRWV -80HSW G5225-89064-80HSW -80HSWV G5225-89064-80HSWV -80HTW G5225-89064-80HTW -80HTWV G5225-89064-80HTWV -85HN G5225-89064-85HN -85HNV G5225-89064-85HNV -85HR G5225-89064-85HR -85HRV G5225-89064-85HRV -85HS G5225-89064-85HS -85HSV G5225-89064-85HSV -85HT G5225-89064-85HT -85HTV G5225-89064-85HTV E-mail: sales@accrmfg.com URL: http://www.accrmfg.com See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 20 DESC drawing PIN 89064 (1) -85HNW Vendor similar designation or type number (2) G5225-89064-85HNW DESC drawing PIN 89064 (1) -85HNWV Vendor similar designation or type number (2) Vendor CAGE Vendor name and address 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 92806-1231 G5225-89064-85HNWV -85HRW G5225-89064-85HRW -85HRWV G5225-89064-85HRWV -85HSW G5225-89064-85HSW -85HSWV G5225-89064-85HSWV -85HTW G5225-89064-85HTW -85HTWV G5225-89064-85HTWV Telephone: (714) 738-6194 Facsimile: (714) 446-0119 E-mail: sales@accrmfg.com URL: http://www.accrmfg.com (1) (2) Parts must be purchased to this DESC PIN to assure that all performance requirements and inspections are met. Do not use vendor PIN's for acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) (3) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) (3) -50AN 40-5-10-A -50ANV 40-5VI-10-A -50AR 40-5-10-R -50ARV 40-5VI-10-R -50AS 40-5-10 -50ASV 40-5VI-10 Vendor CAGE Vendor name and address 61081 Pentair Technical Products (formerly Birtcher) 7328 Trade Street San Diego, CA 92121-3410 -50AT 40-5-10-T -50ATV 40-5VI-10-T -50ANW 40-5-10-LF-A -50ANWV 40-5VI-10-LF-A -50ARW 40-5-10-LF-R -50ARWV 40-5VI-10-LF-R Telephone: (858) 740-2400 -50ASW 40-5-10-LF -50ASWV 40-5VI-10-LF Facsimile: (858) 740-2430 -50ATW 40-5-10-LF-T -50ATWV 40-5VI-10-LF-T -50BN 42-5-10-A -50BNV 42-5VI-10-A -50BR 42-5-10-R -50BRV 42-5VI-10-R -50BS 42-5-10 -50BSV 42-5VI-10 -50BT 42-5-10-T -50BTV 42-5VI-10-T -50BNW 42-5-10-LF-A -50BNWV 42-5VI-10-LF-A -50BRW 42-5-10-LF-R -50BRWV 42-5VI-10-LF-R -50BSW 42-5-10-LF -50BSWV 42-5VI-10-LF -50BTW 42-5-10-LF-T -50BTWV 42-5VI-10-LF-T -50CN 40-5-1013-A -50CNV 40-5VI-1013-A -50CR 40-5-1013-R -50CRV 40-5VI-1013-R -50CS 40-5-1013 -50CSV 40-5VI-1013 -50CT 40-5-1013-T -50CTV 40-5VI-1013-T -50CNW 40-5-1013-LF-A -50CNWV 40-5VI-1013-LFA -50CRW 40-5-1013-LF-R -50CRWV 40-5VI-1013-LFR -50CSW 40-5-1013-LF -50CSWV 40-5VI-1013-LF E-mail: schroff.us@pentair.com URL: http://schroff.pentair.com See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 21 DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) (3) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) (3) -50CTW 40-5-1013-LF-T -50CTWV 40-5VI-1013-LFT -60AN 40-5-12-A -60ANV 40-5VI-12-A -60AR 40-5-12-R -60ARV 40-5VI-12-R -60AS 40-5-12 -60ASV 40-5VI-12 Vendor CAGE Vendor name and address 61081 Pentair Technical Products (formerly Birtcher) 7328 Trade Street San Diego, CA 92121-3410 -60AT 40-5-12-T -60ATV 40-5VI-12-T -60ANW 40-5-12-LF-A -60ANWV 40-5VI-12-LF-A Telephone: (858) 740-2400 -60ARW 40-5-12-LF-R -60ARWV 40-5VI-12-LF-R Facsimile: (858) 740-2430 -60ASW 40-5-12-LF -60ASWV 40-5VI-12-LF -60ATW 40-5-12-LF-T -60ATWV 40-5VI-12-LF-T -60BN 42-5-12-A -60BNV 42-5VI-12-A -60BR 42-5-12-R -60BRV 42-5VI-12-R -60BS 42-5-12 -60BSV 42-5VI-12 -60BT 42-5-12-T -60BTV 42-5VI-12-T -60BNW 42-5-12-LF-A -60BNWV 42-5VI-12-LF-A -60BRW 42-5-12-LF-R -60BRWV 42-5VI-12-LF-R -60BSW 42-5-12-LF -60BSWV 42-5VI-12-LF -60BTW 42-5-12-LF-T -60BTWV 42-5VI-12-LF-T -60CN 40-5-12-A -60CNV 40-5VI-12-A -60CR 40-5-1108-R -60CRV 40-5VI-1108-R -60CS 40-5-1108 -60CSV 40-5VI-1108 -60CT 40-5-1108-T -60CTV 40-5VI-1108-T -60CNW 40-5-12-LF-A -60CNWV 40-5VI-12-LF-A -60CRW 40-5-1108-LF-R -60CRWV 40-5VI-1108-LFR -60CSW 40-5-1108-LF -60CSWV 40-5VI-1108-LF -60CTW 40-5-1108-LF-T -60CTWV 40-5VI-1108-LFT -65BN 42-5-13-A -65BNV 42-5VI-13-A -65BR 42-5-13-R -65BRV 42-5VI-13-R -65BS 42-5-13 -65BSV 42-5VI-13 -65BT 42-5-13-T -65BTV 42-5VI-13-T -65BNW 42-5-13-LF-A -65BNWV 42-5VI-13-LF-A -65BRW 42-5-13-LF-R -65BRWV 42-5VI-13-LF-R -65BSW 42-5-13-LF -65BSWV 42-5VI-13-LF -65BTW 42-5-13-LF-T -65BTWV 42-5VI-13-LF-T -65CN 40-5-13-A -65CNV 40-5VI-13-A -65CR 40-5-1109-R -65CRV 40-5VI-1109-R -65CS 40-5-1109 -65CSV 40-5VI-1109 -65CT 40-5-1109-T -65CTV 40-5VI-1109-T -65CNW 40-5-13-LF-A -65CNWV 40-5VI-13-LF-A -65CRW 40-5-1109-LFR -65CRWV 40-5VI-1109-LFR -65CSW 40-5-1109-LF -65CSWV 40-5VI-1109-LF E-mail: schroff.us@pentair.com URL: http://schroff.pentair.com See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 22 DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) (3) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) (3) -65CTW 40-5-1109-LF-T -65CTWV 40-5VI-1109-LFT -70DN 40-5-14-A -70DNV 40-5VI-14-A -70DR 40-5-14-R -70DRV 40-5VI-14-R -70DS 40-5-14 -70DSV 40-5VI-14 Vendor CAGE Vendor name and address 61081 Pentair Technical Products (formerly Birtcher) 7328 Trade Street San Diego, CA 92121-3410 -70DT 40-5-14-T -70DTV 40-5VI-14-T -70DNW 40-5-14-LF-A -70DNWV 40-5VI-14-LF-A Telephone: (858) 740-2400 -70DRW 40-5-14-LF-R -70DRWV 40-5VI-14-LF-R Facsimile: (858) 740-2430 -70DSW 40-5-14-LF -70DSWV 40-5VI-14-LF -70DTW 40-5-14-LF-T -70DTWV 40-5VI-14-LF-T -75DN 40-5-15-A -75BNV 40-5VI-15-A -75DR 40-5-15-R -75DRV 40-5VI-15-R -75DS 40-5-15 -75DSV 40-5VI-15 -75DT 40-5-15-T -75DTV 40-5VI-15-T -75DNW 40-5-15-LF-A -75DNWV 40-5VI-15-LF-A -75DRW 40-5-15-LF-R -75DRWV 40-5VI-15-LF-R -75DSW 40-5-15-LF -75DSWV 40-5VI-15-LF -75DTW 40-5-15-LF-T -75DTWV 40-5VI-15-LF-T -80DN 40-5-16-A -80DNV 40-5VI-16-A -80DR 40-5-16-R -80DRV 40-5VI-16-R -80DS 40-5-16 -80DSV 40-5VI-16 -80DT 40-5-16-T -80DTV 40-5VI-16-T -80DNW 40-5-16-LF-A -80DNWV 40-5VI-16-LF-A -80DRW 40-5-16-LF-R -80DRWV 40-5VI-16-LF-R -80DSW 40-5-16-LF -80DSWV 40-5VI-16-LF -80DTW 40-5-16-LF-T -80DTWV 40-5VI-16-LF-T -85DN 40-5-17-A -85DNV 40-5VI-17-A -85DR 40-5-17-R -85DRV 40-5VI-17-R -85DS 40-5-17 -85DSV 40-5VI-17 -85DT 40-5-17-T -85DTV 40-5VI-17-T -85DNW 40-5-17-LF-A -85DNWV 40-5VI-17-LF-A -85DRW 40-5-17-LF-R -85DRWV 40-5VI-17-LF-R -85DSW 40-5-17-LF -85DSWV 40-5VI-17-LF -85DTW 40-5-17-LF-T -85DTWV 40-5VI-17-LF-T (1) (2) (3) E-mail: schroff.us@pentair.com URL: http://schroff.pentair.com Parts must be purchased to this DESC PIN to assure that all performance requirements and inspections are met. Do not use vendor PIN's for acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. CAGE 61081 card holders are supplied assembled. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 23 DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) Vendor CAGE Vendor name and address 61081 Pentair Technical Products (formerly Calmark) 7328 Trade Street San Diego, CA 92121-3410 -50EN 226-1006-4.80 -50ENV V226-1006-4.80 -50ER 226-1006-4.80H -50ERV V226-1006-4.80H -50ES 226-1006-4.80T2 -50ESV V226-1006-4.80T2 -50ET 226-1006-4.80T0 -50ETV V226-1006-4.80T0 -50ENW W226-1006-4.80 -50ENWV WV226-1006-4.80 -50ERW W226-1006-4.80H -50ERWV WV226-1006-4.80H Telephone: (858) 740-2400 -50ESW W226-1006-4.80T2 -50ESWV WV226-1006-4.80T2 Facsimile: (858) 740-2430 -50ETW W226-1006-4.80T0 -50ETWV WV226-1006-4.80T0 -50FN 231-1013-4.80 -50FNV V231-1006-4.80 -50FR 231-1013-4.80H -50FRV V231-1006-4.80H -50FS 231-1013-4.80T2 -50FSV V231-1006-4.80T2 -50FT 231-1013-4.80T0 -50FTV V231-1006-4.80T0 -50FNW W231-1013-4.80 -50FNWV WV231-1006-4.80 -50FRW W231-1013-4.80H -50FRWV WV231-1006-4.80H -50FSW W231-1013-4.80T2 -50FSWV WV231-1006-4.80T2 -50FTW W231-1013-4.80T0 -50FTWV WV231-1006-4.80T0 -50GN 226-1007-4.80 -50GNV V226-1007-4.80 -50GR 226-1007-4.80H -50GRV V226-1007-4.80H -50GS 226-1007-4.80T2 -50GSV V226-1007-4.80T2 -50GT 226-1007-4.80T0 -50GTV V226-1007-4.80T0 -50GNW W226-1007-4.80 -50GNWV WV226-1007-4.80 -50GRW W226-1007-4.80H -50GRWV WV226-1007-4.80H -50GSW W226-1007-4.80T2 -50GSWV WV226-1007-4.80T2 -50GTW W226-1007-4.80T0 -50GTWV WV226-1007-4.80T0 -60EN 226-1006-5.80 -60ENV V226-1006-5.80 -60ER 226-1006-5.80H -60ERV V226-1006-5.80H -60ES 226-1006-5.80T2 -60ESV V226-1006-5.80T2 -60ET 226-1006-5.80T0 -60ETV V226-1006-5.80T0 -60ENW W226-1006-5.80 -60ENWV WV226-1006-5.80 -60ERW W226-1006-5.80H -60ERWV WV226-1006-5.80H -60ESW W226-1006-5.80T2 -60ESWV WV226-1006-5.80T2 -60ETW W226-1006-5.80T0 -60ETWV WV226-1006-5.80T0 -60FN 231-1013-5.80 -60FNV V231-1006-5.80 -60FR 231-1013-5.80H -60FRV V231-1006-5.80H -60FS 231-1013-5.80T2 -60FSV V231-1006-5.80T2 -60FT 231-1013-5.80T0 -60FTV V231-1006-5.80T0 -60FNW W231-1013-5.80 -60FNWV WV231-1006-5.80 -60FRW W231-1013-5.80H -60FRWV WV231-1006-5.80H -60FSW W231-1013-5.80T2 -60FSWV WV231-1006-5.80T2 -60FTW W231-1013-5.80T0 -60FTWV WV231-1006-5.80T0 E-mail: schroff.us@pentair.com URL: http://schroff.pentair.com See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 24 DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) -60GN 226-1007-5.80 -60GNV V226-1007-5.80 -60GR 226-1007-5.80H -60GRV V226-1007-5.80H -60GS 226-1007-5.80T2 -60GSV V226-1007-5.80T2 Vendor CAGE Vendor name and address 61081 Pentair Technical Products (formerly Calmark) 7328 Trade Street San Diego, CA 92121-3410 -60GT 226-1007-5.80T0 -60GTV V226-1007-5.80T0 -60GNW W226-1007-5.80 -60GNWV WV226-1007-5.80 -60GRW W226-1007-5.80H -60GRWV WV226-1007-5.80H Telephone: (858) 740-2400 -60GSW W226-1007-5.80T2 -60GSWV WV226-1007-5.80T2 Facsimile: (858) 740-2430 -60GTW W226-1007-5.80T0 -60GTWV WV226-1007-5.80T0 -65EN 226-1006-6.30 -65ENV V226-1006-6.30 -65ER 226-1006-6.30H -65ERV V226-1006-6.30H -65ES 226-1006-6.30T2 -65ESV V226-1006-6.30T2 -65ET 226-1006-6.30T0 -65ETV V226-1006-6.30T0 -65ENW W226-1006-6.30 -65ENWV WV226-1006-6.30 -65ERW W226-1006-6.30H -65ERWV WV226-1006-6.30H -65ESW W226-1006-6.30T2 -65ESWV WV226-1006-6.30T2 -65ETW W226-1006-6.30T0 -65ETWV WV226-1006-6.30T0 -65FN 231-1013-6.30 -65FNV V231-1013-6.30 -65FR 231-1013-6.30H -65FRV V231-1013-6.30H -65FS 231-1013-6.30T2 -65FSV V231-1013-6.30T2 -65FT 231-1013-6.30T0 -65FTV V231-1013-6.30T0 -65FNW W231-1013-6.30 -65FNWV WV231-1013-6.30 -65FRW W231-1013-6.30H -65FRWV WV231-1013-6.30H -65FSW W231-1013-6.30T2 -65FSWV WV231-1013-6.30T2 -65FTW W231-1013-6.30T0 -65FTWV WV231 1013 6.30T0 -65GN 226-1007-6.30 -65GNV V226-1007-6.30 -65GR 226-1007-6.30H -65GRV V226-1007-6.30H -65GS 226-1007-6.30T2 -65GSV V226-1007-6.30T2 -65GT 226-1007-6.30T0 -65GTV V226-1007-6.30T0 -65GNW W226-1007-6.30 -65GNWV WV226-1007-6.30 -65GRW W226-1007-6.30H -65GRWV WV226-1007-6.30H -65GSW W226-1007-6.30T2 -65GSWV WV226-1007-6.30T2 -65GTW W226-1007-6.30T0 -65GTWV WV226-1007-6.30T0 -70HN 226-1084-6.80 -70HNV V226-1084-6.80 -70HR 226-1084-6.80H -70HRV V226-1084-6.80H -70HS 226-1084-6.80T2 -70HSV V226-1084-6.80T2 -70HT 226-1084-6.80T0 -70HTV V226-1084-6.80T0 -70HNW W226-1084-6.80 -70HNWV WV226-1084-6.80 -70HRW W226-1084-6.80H -70HRWV WV226-1084-6.80H -70HSW W226-1084-6.80T2 -70HSWV WV226-1084-6.80T2 -70HTW W226-1084-6.80T0 -70HTWV WV226-1084-6.80T0 E-mail: schroff.us@pentair.com URL: http://schroff.pentair.com See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 25 DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) DESC drawing PIN 89064 (1) Vendor similar designation or type number (2) Vendor CAGE Vendor name and address 61081 Pentair Technical Products (formerly Calmark) 7328 Trade Street San Diego, CA 92121-3410 -75HN 226-1084-7.30 -75HNV V226-1084-7.30 -75HR 226-1084-7.30H -75HRV V226-1084-7.30H -75HS 226-1084-7.30T2 -75HSV V226-1084-7.30T2 -75HT 226-1084-7.30T0 -75HTV V226-1084-7.30T0 -75HNW W226-1084-7.30 -75HNWV WV226-1084-7.30 -75HRW W226-1084-7.30H -75HRWV WV226-1084-7.30H Telephone: (858) 740-2400 -75HSW W226-1084-7.30T2 -75HSWV WV226-1084-7.30T2 Facsimile: (858) 740-2430 -75HTW W226-1084-7.30T0 -75HTWV WV226-1084-7.30T0 -80HN 226-1085-7.80 -80HNV V226-1085-7.80 -80HR 226-1085-7.80H -80HRV V226-1085-7.80H -80HS 226-1085-7.80T2 -80HSV V226-1085-7.80T2 -80HT 226-1085-7.80T0 -80HTV V226-1085-7.80T0 -80HNW W226-1085-7.80 -80HNWV WV226-1085-7.80 -80HRW W226-1085-7.80H -80HRWV WV226-1085-7.80H -80HSW W226-1085-7.80T2 -80HSWV WV226-1085-7.80T2 -80HTW W226-1085-7.80T0 -80HTWV WV226-1085-7.80T0 -85HN 226-1085-8.30 -85HNV V226-1085-8.30 -85HR 226-1085-8.30H -85HRV V226-1085-8.30H -85HS 226-1085-8.30T2 -85HSV V226-1085-8.30T2 -85HT 226-1085-8.30T0 -85HTV V226-1085-8.30T0 -85HNW W226-1085-8.30 -85HNWV WV226-1085-8.30 -85HRW W226-1085-8.30H -85HRWV WV226-1085-8.30H -85HSW W226-1085-8.30T2 -85HSWV WV226-1085-8.30T2 -85HTW W226-1085-8.30T0 -85HTWV WV226-1085-8.30T0 (1) (2) E-mail: schroff.us@pentair.com URL: http://schroff.pentair.com Parts must be purchased to this DESC PIN to assure that all performance requirements and inspections are met. Do not use vendor PIN's for acquisition. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE A CAGE CODE 89064 14933 REV DWG NO. G PAGE 26