Page 1 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 www.psemi.com
Figure 2. Package Type
RFC
RF1 RF2
C1
75 75
75
C2
CMOS
Control
Driver
The PE4280 is an UltraCMOS™ Switch designed for CATV
applications, covering a broad frequency range from DC up to
2.2 GHz. This single-supply SPDT switch integrates a two-pin
CMOS control interface. It also provides low insertion loss with
extremely low bias requirements while operating on a single 3 V
supply. In a typical CATV application, the PE4280 provides for
a cost effective and manufacturable solution when compared to
mechanical relays.
The PE4280 is manufactured on Peregrine’s UltraCMOS™
process, a patented variation of silicon-on-insulator (SOI)
technology on a sapphire substrate, offering the performance of
GaAs with the economy and integration of conventional CMOS.
Product Specification
75 SPDT CATV UltraCMOS™
Switch 5 MHz - 2.2 GHz
Product Description
Figure 1. Functional Diagram
PE4280
Features
75 characteristic impedance
Integrated 75 terminations
CTB performance of 85 dBc
High isolation 60 dB at 1 GHz
Low insertion loss: typically 0.5 dB at
5 MHz, 1.1 dB at 1 GHz
High input IP3: 50 dBm
CMOS two-pin control
Single +3 V supply operation
Low current consumption: 8 µA
Unique all off terminated mode
4x4 mm QFN package
Table 1. Electrical Specifications @ +25 °C (Z
S
= Z
L
= 75 )
Parameter Condition Minimum Typical Maximum Units
Operating Frequency
1
5
2200
MHz
Insertion Loss
5 MHz250 MHz
250 MHz750 MHz
750 MHz1000 MHz
1000 MHz – 2200 MHz
0.5
0.8
0.9
1.1
0.6
0.95
1.1
1.3
dB
Isolation
5 MHz250 MHz
250 MHz750 MHz
750 MHz1000 MHz
1000 MHz – 2200 MHz
67
60
57
44
72
65
60
47
dB
Input IP2
2
5 MHz - 1000 MHz
75
dBm
Input IP3
2
5 MHz - 1000 MHz
50
50
dBm
Input 1dB Compression
2
1000 MHz
29
26
dBm
CTB / CSO
77 & 110 channels;
Power Out = 44 dBmV
-85
dBc
Switching Time
50% CTRL to 10/90 RF
2
µs
Video Feedthrough
3
5 MHz - 1000 MHz
15
mV
pp
Notes: 1. Device linearity will begin to degrade below 5 MHz.
2. Measured in a 50
system.
3. Measured with a 1 ns risetime, 0/3 V pulse and 500 MHz bandwidth
20-lead 4x4 mm QFN
Product Specification
PE4280
Page 2 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 UltraCMOS™ RFIC Solutions
Table 2. Pin Descriptions
Table 3. Absolute Maximum Ratings
Electrostatic Discharge (ESD) Precautions
When handling this UTSi device, observe the
same precautions that you would use with other
ESD-sensitive devices. Although this device
contains circuitry to protect it from damage due to
ESD, precautions should be taken to avoid
exceeding the rating specified.
Latch-Up Avoidance
Unlike conventional CMOS devices, UltraCMOS™
devices are immune to latch-up.
Table 4. Operating Ranges @ 25 °C
Figure 3. Pin Configuration (Top View)
No. Name Description
1
GND
Ground
2
GND
Ground
3
1
RF1
RF I/O
4
4
GND
Ground
5
GND
Ground
6
GND
Ground
7
4
GND
Ground
8
1
RFC
Common
9
4
GND
Ground
10
GND
Ground
11
GND
Ground
12
4
GND
Ground
13
1
RF2
RF I/O
14
GND
Ground
15
GND
Ground
16
2
C2
Control 2
17
2
C1
Control 1
18
3
VSS / GND
Negative Supply Option
19
GND
Ground
20
VDD
Supply
Pad
GND
Ground Pad
Notes:
1. RF pins 3, 8, and 13 must be at 0 VDC. The RF pins do not require DC
blocking capacitors for proper operation if the 0 VDC requirement is met.
2. Pins 16 and 17 are the CMOS controls that set the three operating
states.
3. Connect pin 18 to GND to enable the on-chip negative voltage generator.
Connect
pin 18 to V
SS
(-3 V) to bypass and disable internal -3 V supply
generator. Also, see paragraph “Switching Frequency.”
4. Customer can add external resistance to ground to change or modify
termination resistance.
Switching Frequency
The PE4280 has a maximum 25 kHz switching
rate when the internal negative voltage generator
is used (pin 18=GND). The rate at which the
PE4280 can be switched is only limited to the
switching time if an external -3 V supply is
provided at pin 18 (V
SS
).
Symbol Parameter/Condition Min Max Unit
V
DD
Power supply voltage -0.3 4.0 V
V
I
Voltage on any DC input -0.3 V
DD
+
0.3 V
P
RF
RF CW power 24 dBm
T
ST
Storage temperature -65 150 °C
T
OP
Operating temperature -40 85 °C
V
ESD
ESD voltage
(Human Body Model) 1000 V
Parameter Min Typ Max Unit
V
DD
Power Supply
2.7
3.0
3.3
V
I
DD
Power Supply Current
(V
DD
= 3 V)
8
20
µA
Control Voltage High
70% V
DD
V
Control Voltage Low
30% V
DD
V
Exceeding absolute maximum ratings may cause
permanent damage. Operation should be re-
stricted to the limits in the Operating Ranges ta-
ble. Operation between operating range maxi-
mum and absolute maximum for extended periods
may reduce reliability.
GND 15
14
13
12
11
3
4
5
2
1
17
16
18
19
20
9
10
8
7
6
CTRL2
GND
GND
GND
GND
GND
RFC
VDD
CTRL1
VSS/GND
GND
GND
GND
RF2
GND, RF2 Term.
GND
GND, RF1 Term.
RF1
GND
GND
Product Specification
PE4280
Page 3 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 www.psemi.com
Table 5. RF Path Truth Table
Table 6. Termination Truth Table
Notes: 1. The operation of the PE4280 is not supported or characterized in the C1=VDD and C2=VDD state.
2. “X” denotes termination enabled.
C1
C2
RFC – RF1
RFC – RF2
Low
Low
OFF
OFF
Low
High
OFF
ON
High
Low
ON
OFF
High
High
N/A
1
N/A
1
C1
C2
RFC – 75
RF1 – 75 Ω
RF2 – 75 Ω
Low
Low
X
2
X
2
X
2
Low
High
X
2
High
Low
X
2
High
High
N/A
1
N/A
1
N/A
1
Product Specification
PE4280
Page 4 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 UltraCMOS™ RFIC Solutions
Evaluation Kit
The SPDT Switch Evaluation Kit board was
designed to ease customer evaluation of the
PE4280 SPDT switch. The RFC port is
connected through a 75 transmission line to J2.
Port 1 and Port 2 are connected through 75
transmission lines to J1 and J3. A through
transmission line connects F connectors J4 and
J5. This transmission line can be used to
estimate the loss of the PCB over the
environmental conditions being evaluated.
The board is constructed of a four metal layer
FR4 material with a total thickness of 0.062”. The
transmission lines were designed using a
coplanar waveguide with ground plane (28 mil
core, 21mil width, 30 mil gap).
J6 provides a means for controlling DC and digital
inputs to the device. The provided jumpers short
the package pin to ground for logic low. When
the jumper is removed, the pin is pulled up to V
DD
for logic high.
When the jumper is in place, 3 µA of current will
flow through the 1 M pull up resistor. This extra
current should not be attributed to the
requirements of the device.
Proper PCB design is essential for full isolation
performance. This eval board demonstrates good
trace and ground management for minimum
coupling and radiation.
Figure 4. Evaluation Board Layouts
Peregrine Specification 101/0148~03A
Figure 5. Evaluation Board Schematic
Peregrine Specification 102/0195~02A
75 OHM T-Line
75 OHM T-Line
75 OHM T-Line
75 OHM T-Line
1
2
J5J5
R1
1M
R1
1M
R2
1M
R2
1M
VDD
1
GND
3
VSS/GND
5
GND
7
GND 2
GND 4
GND 6
GND 8
GND 1 0
GND 1 2
GND 1 4
C2
13
C1
9
GND
11
J
6
HEADER 7X2
J
6
HEADER 7X2
1
2
J4J4
1
2
J3J3
C3
DNI
C3
DNI
GND
7
GND
2
RF1
3
GND
4
GND
5
GND
6
GND
1
RFC
8
GND
9
GND
10
GN D 12
GN D 11
RF2 13
GN D 14
GN D 15
C2 16
C1 17
VSS/GND 18
GND 19
VDD 20
GND
21
U1
PE4280
U1
PE4280
C1
DNI
C1
DNI
C2
DNI
C2
DNI
1
2
J2J2
1
2
J1J1
Product Specification
PE4280
Page 5 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 www.psemi.com
-100
-90
-80
-70
-60
-50
-40
0 500 1000 1500 2000 2500 3000
RF1 - RF2 (RF1 Thru)
RF1 - RF2 (RF2 Thru)
RF1 - RF2 (RF1 & 2 OPEN)
Isolation (dB)
Frequency (MHz)
-100
-90
-80
-70
-60
-50
-40
0 500 1000 1500 2000 2500 3000
RFC - RF1 (RF2 OPEN)
RFC - RF2 (RF1 OPEN)
Isolation (dB)
Frequency (MHz)
-100
-90
-80
-70
-60
-50
-40
0 500 1000 1500 2000 2500 3000
RFC - RF1 (RF2 CLOSED)
RFC - RF2 (RF1 CLOSED)
Isolation (dB)
Frequency (MHz)
-1.8
-1.6
-1.4
-1.2
-1
-0.8
-0.6
-0.4
-0.2
0 500 1000 1500 2000 2500 3000
25C
-40C
85C
Insertion Loss (dB)
Frequency (MHz)
Typical Performance Data from -4C to +85°C (Unless otherwise noted)
Figure 7. Input to Output Isolation
Figure 9. Isolation – RF1 To RF2 Figure 8. Input to Output Isolation
Figure 6. Insertion Loss (RFC to RF1 or RF2)
(75 impedance except as indicated)
Product Specification
PE4280
Page 6 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 UltraCMOS™ RFIC Solutions
0
10
20
30
40
50
60
0 500 1000 1500 2000 2500 3000
Input IP3
1dB Compression
Power (dBm)
Frequency (MHz)
-35
-30
-25
-20
-15
-10
-5
0
0 500 1000 1500 2000 2500 3000
RFC Terminated
RFC - RF1 CLOSED
Return Loss (dB)
Frequency (MHz)
Typical Performance Data @ +25°C (Unless otherwise noted)
Figure 11. RF1 Return Loss
Figure 13. Linearity: 50 Ω Impedance
Figure 12. RF2 Return Loss
Figure 10. RFC Return Loss
(75 impedance except as indicated)
Product Specification
PE4280
Page 7 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 www.psemi.com
Figure 14. Package Drawing (mm)
4x4 mm 20-Lead QFN
Figure 15. Tape and Reel Drawing
Table 7. Ordering Information
Order Code Part Marking Description Package Shipping Method
4280-01 4280 PE4280-20QFN 4x4 mm-75A 20-lead 4x4 mm QFN, Matte Tin Lead Finish 75 units/Tube
4280-02 4280 PE4280-20QFN 4x4 mm-3000C 20-lead 4x4 mm QFN, Matte Tin Lead Finish 3000 units/T&R
4280-00 PE4280-EK PE4280-20QFN 4x4 mm-EK Evaluation Kit 1/Box
4280-51 4280 PE4280G-20QFN 4x4 mm-75A Green 20-lead 4x4 mm QFN, Matte Tin Lead Finish 75 units/Tube
4280-52 4280 PE4280G-20QFN 4x4 mm-3000C Green 20-lead 4x4 mm QFN, Matte Tin Lead Finish 3000 units/T&R
PE4280MLIAA 4280 PE4280-20QFN 4x4 mm-75 20-lead 4x4 mm QFN, NiPdAu Lead Finish 75 units/Tube
PE4280MLIAA-Z 4280 PE4280-20QFN 4x4 mm-3000 20-lead 4x4 mm QFN, NiPdAu Lead Finish 3000 units/T&R
EK4280-01 PE4280-EK PE4280-20QFN 4x4 mm-EK Evaluation Kit 1/Box
Product Specification
PE4280
Page 8 of 8
©2010 Peregrine Semiconductor Corp. All rights reserved. Document No. 70-0164-04 www.psemi.com
Sales Offices
The Americas
Peregrine Semiconductor Corporation
9380 Carroll Park Drive
San Diego, CA 92121
Tel: 858-731-9400
Fax: 858-731-9499
Europe
Peregrine Semiconductor Europe
Bâtiment Maine
13-15 rue des Quatre Vents
F-92380 Garches, France
Tel: +33-1-4741-9173
Fax : +33-1-4741-9173
For a list of representatives in your area, please refer to our
Web site at: www.psemi.com
Data Sheet Identification
Advance Information
The product is in a formative or design stage. The data
sheet contains design target specifications for product
development. Specifications and features may change in
any manner without notice.
Preliminary Specification
The data sheet contains preliminary data. Additional data
may be added at a later date. Peregrine reserves the right
to change specifications at any time without notice in order
to supply the best possible product.
Product Specification
The data sheet contains final data. In the event Peregrine
decides to change the specifications, Peregrine will notify
customers of the intended changes by issuing a CNF
(Customer Notification Form).
The information in this data sheet is believed to be reliable.
However, Peregrine assumes no liability for the use of this
information. Use shall be entirely at the user’s own risk.
No patent rights or licenses to any circuits described in this
data sheet are implied or granted to any third party.
Peregrine’s products are not designed or intended for use in
devices or systems intended for surgical implant, or in other
applications intended to support or sustain life, or in any
application in which the failure of the Peregrine product could
create a situation in which personal injury or death might occur.
Peregrine assumes no liability for damages, including
consequential or incidental damages, arising out of the use of
its products in such applications.
The Peregrine name, logo, and UTSi are registered trademarks
and UltraCMOS, HaRP, MultiSwitch and DuNE are trademarks
of Peregrine Semiconductor Corp.
High-Reliability and Defense Products
Americas
San Diego, CA, USA
Phone: 858-731-9475
Fax: 848-731-9499
Europe/Asia-Pacific
Parc Cezanne 1
380 Avenue Archimède
Parc de la Duranne
13857 Aix-En-Provence Cedex 3
France
Tel: +33(0)-4-4239-3361
Fax: +33(0)-4-4269-7227
Peregrine Semiconductor, Asia Pacific (APAC)
Shanghai, 200040, P.R. China
Tel: +86-21-5836-8276
Fax: +86-21-5836-7652
Peregrine Semiconductor, Korea
#B-2607, Kolon Tripolis, 210
Geumgok-dong, Bundang-gu, Seongnam-si
Gyeonggi-do, 463-943 South Korea
Tel: +82-31-728-3939
Fax: +82-31-728-3940
Peregrine Semiconductor K.K., Japan
601 Yaesu Kyodo Building
2-5-9 Yaesu, Chuo-ku
Tokyo 104-0028 Japan
Tel: +81-3-3527-9841
Fax: +81-3-3527-9848