GbX-LTM Backplane Press-In Tool GbX-LTM Backplane Module Installation Press-In Tool Application Tooling Specification Sheet Order No. 62202-2026 FEATURES Polarized tool prevents product damage Tool provides uniform distribution of press force across entire pin array May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools SCOPE Products: GbX-LTM Backplane Signal Module Assembly, 75465 Series, (4-Pair by 25 Column Assemblies). See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. Series No. 75465 Guide Style Columns Open Wall 25 Left End 25 Right End 25 75465-0200 75465-0207 75465-2210 75465-2217 75465-2223 75465-4210 75465-4217 75465-4223 75465-0201 75465-0208 75465-2211 75465-2218 75465-2224 75465-4211 75465-4218 75465-4224 Assembly Order Number 75465-0202 75465-0203 75465-0209 75465-2212 75465-2213 75465-2219 75465-2220 75465-2225 75465-2227 75465-4212 75465-4213 75465-4219 75465-4220 75465-4225 75465-4227 75465-0204 75465-0205 75465-2214 75465-2221 75465-2228 75465-4214 75465-4221 75465-4228 75465-2215 75465-2222 75465-2229 75465-4215 75465-4222 75465-4229 Tool Setup Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1. ALONE WITH 62201-95XX RAIL Figure 1 Doc No: ATS-622022026 Revision: A Release Date: 04-26-13 Revision Date: 04-26-13 UNCONTROLLED COPY Page 1 of 3 GbX-LTM Backplane Press-In Tool Tool Installation The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools. Rail Part Number Rail Overall Length 62201-9501 24mm (0.94 in) 62201-9502 72mm (2.83 in) 62201-9503 156mm (6.14 in) 62201-9504 216mm (8.50 in) 62201-9509 254mm (10.0 in) 62201-9511 305mm (12.0 in) Reference: This Press-In Tool is 46.2mm (1.82 in.) long. Printed Circuit Board (PCB) Support The GbX-UTM connectors require a significant amount of force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole pattern. Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must furnish their own support plate. When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through the PCB thickness. Press Equipment Recommendations Many types of presses can be used to install GbX-LTM connectors, but to assure consistent connector installation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of force and distance data. Tool Operation 1. Carefully insert, by hand, the backplane signal module(s) into the PCB hole pattern. Make sure the connector(s) are oriented properly by confirming the location of the #1 circuit notch with respect to the PCB layout. Doc No: ATS-622022026 Revision: A Release Date: 04-26-13 Revision Date: 04-26-13 UNCONTROLLED COPY Page 2 of 3 GbX-LTM Backplane Press-In Tool PRESS-IN TOOL ORIENTATION PEG ORIENTATION PEG SLOT IN MODULE ASSEMBLY Figure 2 PCB MODULE ASSEMBLY 2. Insert the application tool into the header assembly with the orientation peg on the tool entering the #1 circuit notch at the top of the connector housing. See Figure 2. 3. Using the application tool and an appropriate press, seat the header assembly until there is less than 0.25mm (.010 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3. .25 MAX. .010 Figure 3 There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing). CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press manufacturer's instruction manual. CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. Visit our Web site at http://www.molex.com Doc No: ATS-622022026 Revision: A Release Date: 04-26-13 Revision Date: 04-26-13 UNCONTROLLED COPY Page 3 of 3