SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 SINGLE M-LVDS RECEIVERS FEATURES APPLICATIONS * * * * * * * * * * (1) Low-Voltage Differential 30- to 55- Line Receivers for Signaling Rates(1) up to 250Mbps; Clock Frequencies up to 125MHz SN65MLVD2 Type-1 Receiver Incorporates 25 mV of Input Threshold Hysteresis SN65MLVD3 Type-2 Receiver Provides 100 mV Offset Threshold to Detect Open-Circuit and Idle-Bus Conditions Wide Receiver Input Common-Mode Voltage Range, -1 V to 3.4 V, Allows 2 V of Ground Noise Improved VIT (35 mV) Meets or Exceeds the M-LVDS Standard TIA/EIA-899 for Multipoint Topology High Input Impedance with Low Supply Voltage Bus-Pin HBM ESD Protection Exceeds 9 kV Packaged in 8-Pin SON (DRB) 70% Smaller Than 8-Pin SOIC * * * Parallel Multipoint Data and Clock Transmission via Backplanes and Cables Cellular Base Stations Central Office Switches Network Switches and Routers PACKAGE AND PIN-OUT SN65MLVD2DRB SN65MLVD3DRB SON-8 VCC 1 8 VCC RE 2 7 B R 3 6 A GND 4 5 GND The signaling rate of a line is the number of voltage transitions that are made per second, expressed in the units bps (bits per second). DESCRIPTION The SN65MLVD2 and SN65MLVD3 are single-channel M-LVDS receivers. These devices are designed in full compliance with the TIA/EIA-899 (M-LVDS) standard, which are optimized to operate at signaling rates up to 250 Mbps. Each receiver channel is controlled by a receive enable (RE). When RE = low, the corresponding channel is enabled; when RE = high, the corresponding channel is disabled. The M-LVDS standard defines two types of receivers, designated as Type-1 and Type-2. Type-1 receivers (SN65MLVD2) have thresholds centered about zero with 25 mV of hysteresis to prevent output oscillations with loss of input; Type-2 receivers (SN65MLVD3) implement a failsafe by using an offset threshold. Receiver outputs are slew rate controlled to reduce EMI and crosstalk effects associated with large current surges. The devices are characterized for operation from -40C to 85C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2006, Texas Instruments Incorporated SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 TYPICAL APPLICATION (System Clock - Primary) (System Clock - Secondary) User defined frequency < 100 MHz 19.44 MHz 8 KHz M-LVDS Transceiver M-LVDS Transceiver 19.44 MHz 8 KHz M-LVDS Transceiver M-LVDS Transceiver User defined frequency < 100 MHz M-LVDS Transceiver 80 RT CLK1A (8 KHz) 80 RT 80 RT CLK1B (8KHz) 80 RT 80 R CLK2A (19.44 MHz) 80 R CLK2B (19.44 MHz) 80 R 80 R T T T T 80 RT CLK3A (user defined frequency) 80 RT 80 R CLK3B (user defined frequency) 80 R T M-LVDS Receivers CLK1A 8 KHz M-LVDS Receivers CLK1B 8 KHz M-LVDS Receivers CLK2A 19.44 MHz M-LVDS Receivers CLK2B 19.44 MHz M-LVDS Receivers AdvancedTCA Backplane - Synchronized System Clock Submit Documentation Feedback M-LVDS Receivers CLK3A CLK3B User defined frequency Line Card 1 - N 2 M-LVDS Transceiver T SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION (1) PART NUMBER FUNCTION PART MARKING PACKAGE / CARRIER SN65MLVD2DRBT M-LVDS Type 1 Receiver MF2 8-Pin SON / Small Tape and Reel SN65MLVD2DRBR M-LVDS Type 1 Receiver MF2 8-Pin SON / Tape and Reel SN65MLVD3DRBT M-LVDS Type 2 Receiver MF3 8-Pin SON / Small Tape and Reel SN65MLVD3DRBR M-LVDS Type 2 Receiver MF3 8-Pin SON / Tape and Reel (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) VCC (1) VALUE UNIT -0.5 to 4 V RE -0.5 to 4 V A or B -1.8 to 4 V R -0.3 to 4 V Supply voltage range (2) Input voltage range Output voltage range Human-body model (3) Electrostatic discharge All other pins 7 A, B 9 Machine model (4) All pins 200 V Field-induced-charged-device model (5) All pins 2 kV Continuous power dissipation (1) (2) (3) (4) (5) kV See Dissipation Rating Table Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values, except differential I/O bus voltages, are with respect to network ground terminal. Tested in accordance with JEDEC Standard 22, Test Method A114-A. Bus pin stressed with respect to a common connection of GND and VCC. Tested in accordance with JEDEC Standard 22 Test Method A115-A. Tested in accordance with EIA-JEDEC JESD22-C101C. PACKAGE DISSIPATION RATINGS (1) PACKAGE 8-SON DRB (1) (2) PCB TYPE TA 25C POWER RATING DERATING FACTOR (2) ABOVE TA = 25C TA = 85C POWER RATING Low-K 280 mW 2.80 mW/C 112 mW High-K 662 mW 6.62 mW/C 264 mW The thermal dissipations are in the consideration of soldering down the powerPAD without via on each type of boards. This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. THERMAL CHARACTERISTICS PARAMETER JB Junction-to-board thermal resistance JC Junction-to-case thermal resistance PD Device power dissipation TEST CONDITIONS MIN TYP MAX C/W 98 RE at 0 V, CL = 15 pF, VID = 400 mV, 125 MHz Submit Documentation Feedback UNIT C/W 89 90 mW 3 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN NOM MAX VCC Supply voltage 3 3.3 3.6 V VIH High-level input voltage 2 VCC V VIL Low-level input voltage GND 0.8 V VA or VB Voltage at any bus terminal -1.4 3.8 V |VID| Magnitude of differential input voltage 0.035 VCC V VIC Differential common-mode input voltage -1 RL Differential load resistance 30 1/tUI Signaling rate TA Operating free-air temperature 3.4 V 50 -40 UNIT 250 Mbps 85 C DEVICE ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER ICC (1) Supply current TEST CONDITIONS MIN TYP (1) MAX RE at 0 V, CL = 15 pF, VID = 400 mV, 125 MHz 25 UNIT mA All typical values are at 25C and with a 3.3-V supply voltage. RECEIVER ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER VIT+ Positive-going differential input voltage threshold VIT- Differential input voltage hysteresis (VIT+- VIT-) MIN TYP (1) MAX Type 1 35 Type 2 135 Negative-going differential input voltage Type 1 threshold Type 2 VHYS See Figure 1, Table 1 and Table 2 -35 UNIT mV mV 65 Type 1 25 Type 2 0 mV VOH High-level output voltage IOH = -8 mA VOL Low-level output voltage IOL = 8 mA IIH High-level input current VIH = 2 V to VCC -10 IIL Low-level input current VIL = GND to 0.8 V -10 IOZ High-impedance output current VO = 0 V or VCC -10 15 A IA or IB Receiver input current One input (VA or VB) = -1.4 V or 3.8 V, Other input = 1.2 V -20 20 A IAB -4 4 A -20 20 A -4 4 A Receiver differential input current (IA- IB) VA = VB = -1.4 V or 3.8 V IA(OFF) or IB(OFF) Receiver input current One input (VA or VB) = -1.4 V or 3.8 V, Other input = 1.2 V, VCC = GND or 1.5 V IAB(OFF) Receiver power-off differential input current (IA- IB) VA = VB = -1.4 V or 3.8 V, VCC = GND or 1.5 V CA or CB Input capacitance VI = 0.4sin(30E6t) + 0.5V, (2) Other input at 1.2 V CAB Differential input capacitance VAB = 0.4sin(30E6t) + 0.5 V (2) CA/B Input capacitance balance, (CA/CB) (1) (2) 4 TEST CONDITIONS 2.4 Submit Documentation Feedback V A A 3 pF 2.5 0.99 All typical values are at 25C and with a 3.3-V supply voltage. HP4194A impedance analyzer (or equivalent) V 0.4 1.01 pF SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 RECEIVER SWITCHING CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT tPLH Propagation delay time, low-to-high-level output 2 6 ns tPHL Propagation delay time, high-to-low-level output 2 6 ns tr Output signal rise time 1 2.3 tf Output signal fall time CL = 15 pF, See Figure 2 tsk(p) Pulse skew (|tPHL- tPLH|) tsk(pp) Part-to-part skew tjit(per) Period jitter, rms (1 standard deviation) (2) tjit(c-c) Cycle-to-cycle jitter, 2.3 Type 1 90 210 Type 2 45 250 125 MHz clock input rms (3) 125 MHz clock Type 1 Deterministic jitter (2) tjit(det) 1 Type 2 Type 1 input (4) 250 Mbps 215-1 PRBS input (5) ps 1 ns 10 ps 8 ps 500 ps 450 ps 8 ps tjit(ran) Random jitter (2) 8 ps tPZH Enable time, high-impedance-to-high-level output CL = 15 pF, See Figure 3 15 ns tPZL Enable time, high-impedance-to-low-level output CL = 15 pF, See Figure 3 15 ns tPHZ Disable time, high-level-to-high-impedance output CL = 15 pF, See Figure 3 10 ns tPLZ Disable time, low-level-to-high-impedance output CL = 15 pF, See Figure 3 10 ns (1) (2) (3) (4) (5) Type 2 250 Mbps 215-1 PRBS input (5) ns All typical values are at 25C and with a 3.3-V supply voltage. Jitter measured by triggering off of the input source to track out the associated input jitter. Stimulus jitter has been subtracted from the numbers. Measured over 75K samples Measured over BER = 10-6. TERMINAL FUNCTIONS TERMINAL NAME NO. I/O DESCRIPTION A 6 I M-LVDS Non-inverting input B 7 I M-LVDS Inverting input R 3 O Data output from receivers RE 2 I Receiver enable, active low, enables all receivers GND 4, 5 Circuit ground VCC 1, 8 Supply voltage DEVICE FUNCTION TABLES TYPE-1 RECEIVER (SN65MLVD2) INPUTS (1) (1) TYPE-2 RECEIVER (SN65MLVD3) OUTPUT (1) VID = VA- VB RE R INPUTS (1) OUTPUT (1) VID = VA- VB RE R VID 35 mV L H VID 135 mV L H -35 mV VID 35 mV L ? 65 mV VID 135 mV L ? VID - 35 mV L L VID 65 mV L L X H Z X H Z X Open Z X Open Z Open Circuit L ? Open Circuit L L H=high level, L=low level, Z=high impedance, X=Don't care, ?=indeterminate Submit Documentation Feedback 5 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 EQUIVALENT INPUT AND OUTPUT SCHEMATIC DIAGRAMS Receiver Enable VCC 360 kW 400 W RE 7V Receiver Input VCC Receiver Output VCC 100 kW 100 kW 250 kW 250 kW 10 W R B A 10 W 200 kW 200 kW 7V 6 Submit Documentation Feedback SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 PARAMETER MEASUREMENT INFORMATION IA A IO R V ID (V A +V B )/2 V CM B VA VO IB VB Figure 1. Receiver Voltage and Current Definitions Table 1. Type-1 Receiver Input Threshold Test Voltages APPLIED VOLTAGES (1) RESULTING DIFFERENTIAL INPUT VOLTAGE RESULTING COMMON-MODE INPUT VOLTAGE VID VIC RECEIVER OUTPUT (1) VIA VIB 2.400 0.000 2.400 1.200 0.000 2.400 - 2.400 1.200 L 3.400 3.365 0.035 3.3825 H H 3.365 3.400 - 0.035 3.3825 L -0.965 -1 0.035 -0.9825 H -1 -0.965 - 0.035 -0.9825 L H= high level, L = low level, output state assumes receiver is enabled (RE = L) Table 2. Type-2 Receiver Input Threshold Test Voltages APPLIED VOLTAGES (1) RESULTING DIFFERENTIAL INPUT VOLTAGE RESULTING COMMON-MODE INPUT VOLTAGE RECEIVER OUTPUT (1) VIA VIB VID VIC 2.400 0.000 2.400 1.200 0.000 2.400 - 2.400 1.200 L 3.400 3.265 0.135 3.3325 H 3.4000 3.335 0.065 3.3675 L -0.865 -1 0.135 -0.9325 H -0.935 -1 0.065 -0.9675 L H H= high level, L = low level, output state assumes receiver is enabled (RE = L) Submit Documentation Feedback 7 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 VID VA CL 15 pF VB VO VA 1.2 V VB 0.8 V VID 0.4 V 0V -0.4 V tPHL tPLH VO 90% 10% tf tr VOH VCC 2 VOL A. All input pulses are supplied by a generator having the following characteristics: tr or tf 1 ns, Frequency = 1 MHz, duty cycle = 50 5%. CL is a combination of a 20%-tolerance, low-loss ceramic, surface-mount capacitor and fixture capacitance within 2 cm of the D.U.T. B. The measurement is made on test equipment with a -3dB bandwidth of at least 1 GHz. Figure 2. Receiver Timing Test Circuit and Waveforms 8 Submit Documentation Feedback SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 1.2 V B RL 499 W A CL 15 pF Inputs RE VO VTEST VTEST VCC 0.8 V A VCC VCC 2 0V RE tPZL tPLZ VO VCC VCC V 2 + 0.5 V OL VOL VTEST 0V 1.6 V A VCC VCC 2 0V RE tPZH tPHZ VO VOH VOH VCC 2 0V 0.5 V A. All input pulses are supplied by a generator having the following characteristics: tr or tf 1 ns, frequency = 1 MHz, duty cycle = 50 5%. B. RL is 1% tolerance, metal film, surface mount, and located within 2 cm of the D.U.T C. CL is the instrumentation and fixture capacitance within 2 cm of the D.U.T. and 20%. The measurement is made on test equipment with a -3dB bandwidth of at least 1GHz. Figure 3. Receiver Enable/Disable Time Test Circuit and Waveforms Submit Documentation Feedback 9 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 INPUTS VA - VB VCM CLOCK INPUT VA - VB 0.4 V 1/fo 1.0 V Period Jitter IDEAL OUTPUT VOH VCC /2 VOL VA 1/fo PRBS INPUT ACTUAL OUTPUT V OH VB VCC/2 VOL Peak to Peak Jitter VOH tc(n) OUTPUT tjit(per) = | tc(n) - 1/fo | VCC/2 VOL Cycle to Cycle Jitter OUTPUT t jit(pp) VOH VCC /2 VOL tc(n) tc(n+1) tjit(cc) = | tc(n) - tc(n+1)| A. All input pulses are supplied by the Agilent 81250 Parallel BERT Stimulus System with plug-in E4832A. B. The cycle-to-cycle jitter measurement is made on a TEK TDS6604 running TDSJIT3 application software C. Period jitter is measured using a 125-MHz 50 1% duty cycle clock input. D. Deterministic jitter and random jitter are measured using a 250-Mbps 215-1 PRBS input Figure 4. Receiver Jitter Measurement Waveforms 10 Submit Documentation Feedback SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs FREQUENCY RECEIVER (TYPE-1) PROPAGATION DELAY TIME vs FREE-AIR TEMPERATURE 6 12 5.5 MLVD3 (Type 2) PD - Propagation Delay Time - ns ICC - Supply Current - mA 10 MLVD2 (Type 1) 8 6 4 VCC = 3.3 V, TA = 25C, VID = 400 mV, VIC = 1 V 2 50 75 100 f - Frequency - MHz 4 tPLH 3.5 tPHL 3 2 -40 125 -8.75 22.5 53.75 TA - Free-Air Temperature - C Figure 5. Figure 6. RECEIVER (TYPE-2) PROPAGATION DELAY TIME vs FREE-AIR TEMPERATURE RECEIVER (TYPE-1) TRANSITION TIME vs FREE-AIR TEMPERATURE 5 2.2 VCC = 3.3 V, f = 1 MHz, CL = 15 pF tr/tf - Rising/Falling Transition Time - ns 5.5 85 2.3 6 PD - Propagation Delay Time - ns 4.5 2.5 0 25 5 VCC = 3.3 V, f = 1 MHz, CL = 15 pF 4.5 4 tPHL 3.5 tPLH 3 2.5 2.1 VCC = 3.3 V, f = 1 MHz, CL = 15 pF 2 1.9 1.8 tr 1.7 1.6 1.5 1.4 tf 1.3 1.2 1.1 2 -40 -8.75 22.5 53.75 TA - Free-Air Temperature - C 85 1 -40 Figure 7. -8.75 22.5 53.75 TA - Free-Air Temperature - C 85 Figure 8. Submit Documentation Feedback 11 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 TYPICAL CHARACTERISTICS (continued) RECEIVER (TYPE-2) TRANSITION TIME vs FREE-AIR TEMPERATURE RECEIVER (TYPE-1) TRANSITION TIME vs OUTPUT LOAD CAPACITOR 2.3 1.8 VCC = 3.3 V, f = 1 MHz, CL = 15 pF 2.1 2 1.9 1.8 1.7 tr 1.6 1.5 1.4 tf 1.3 1.2 1.1 1.6 1.5 1.4 tr 1.3 1.2 1.1 1 tf 0.9 0.8 0.7 0.6 1 -40 -8.75 22.5 53.75 TA - Free-Air Temperature - C 0.5 85 5 7.5 11 13 CL - Output Load Capacitor - pF Figure 9. Figure 10. RECEIVER (TYPE-2) TRANSITION TIME vs OUTPUT LOAD CAPACITOR ADDED RECEIVER PEAK-TO-PEAK JITTER vs SIGNALING RATE 1.8 15 500 VCC = 3.3 V, f = 1 MHz, CL = 15 pF 1.6 450 tjit(pp) - Peak-to-Peak Jitter - ps 1.7 tr/tf - Rising/Falling Transition Time - ns VCC = 3.3 V, f = 1 MHz, CL = 15 pF 1.7 tr/tf - Rising/Falling Transition Time - ns tr/tf - Rising/Falling Transition Time - ns 2.2 1.5 1.4 1.3 tr 1.2 1.1 1 0.9 0.8 tf 0.7 VCC = 3.3 V, TA = 25C, 15 2 - 1 PRBS NRZ, See Figure 4 400 MLVD2 (Type 1) 350 MLVD3 (Type 2) 300 250 200 150 0.6 0.5 5 7.5 11 13 CL - Output Load Capacitor - pF 15 100 50 Figure 11. 12 100 200 150 Signaling Rate - Mbps Figure 12. Submit Documentation Feedback 250 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 TYPICAL CHARACTERISTICS (continued) ADDED RECEIVER PERIOD JITTER vs CLOCK FREQUENCY ADDED RECEIVER CYCLE-TO-CYCLE JITTER vs CLOCK FREQUENCY 5 5 tjit(c-c) rms - Cycle-to-Cycle Jitter - ps VCC = 3.3 V, TA = 25C, See Figure 4 tjit(per) rms - Period Jitter - ps 4 3 2 MLVD2 (Type 1) MLVD3 (Type 2) 1 0 25 VCC = 3.3 V, TA = 25C, See Figure 4 4 3 MLVD2 (Type 1) 2 1 MLVD3 (Type 2) 0 50 75 100 fCLK - Clock Frequency - MHz 125 25 Figure 13. 75 100 50 fCLK - Clock Frequency - MHz 125 Figure 14. 33.5 mV/div EYE PATTERNS 666.9 ps/div Figure 15. SN65MLVD2 Output (VCC = 3.3 V, CL = 15 pF) 250 Mbps 215-1 PRBS Submit Documentation Feedback 13 SN65MLVD2 SN65MLVD3 www.ti.com SLLS767 - NOVEMBER 2006 33.5 mV/div TYPICAL CHARACTERISTICS (continued) 666.9 ps/div Figure 16. SN65MLVD3 Output (VCC = 3.3 V, CL = 15 pF) 250 Mbps 215-1 PRBS 14 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 11-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN65MLVD2DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD2DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD2DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD2DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD3DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD3DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD3DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65MLVD3DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SN65MLVD2DRBR SON DRB 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 SN65MLVD2DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 SN65MLVD3DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 SN65MLVD3DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65MLVD2DRBR SON DRB 8 3000 367.0 367.0 35.0 SN65MLVD2DRBT SON DRB 8 250 210.0 185.0 35.0 SN65MLVD3DRBR SON DRB 8 3000 367.0 367.0 35.0 SN65MLVD3DRBT SON DRB 8 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated