3 Self-Extinguishing Hot Melt Adhesive 3748 VO Technical Data Product Description February, 2015 3MTM Hot Melt Adhesive 3748 VO is a tough, flexible, thermoplastic hot melt, 100% solids adhesive which exhibits good peel adhesion and thermal shock properties along with higher heat resistance. It features excellent electrical properties which make it ideal for use on printed wiring board and other electronic bonding applications. Hot Melt Adhesive 3748 VO is self-extinguishing and has a UL 94 VO rating. In addition to electronic applications, it is also useful in many general industrial bonding and sealing applications where a self-extinguishing characteristic is required. Features * Excellent Adhesion * Good Electrical Properties * Non Corrosive to Metal Typical Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Base Resin: Polyolefin Color: Light Yellow Specific Gravity: 1.09 Ball and Ring Softening Point: Viscosity: 305F (152C) @ 356F (180C) @ 392F (200C) @ 428F (220C) 8,500 cps 5,000 cps 3,300 cps UL 94 (Flammability Classification): V-O Shore D Hardness (ASTM D 2240): 26 @ 77F (25C) Suggested Application Equipment: - 3MTM Hot Melt Applicator TC or TCQ - 3MTM Hot Melt Applicator EC - Temperature Module #4 - 3MTM Hot Melt Applicator PG II 3MTM Self-Extinguishing Hot Melt Adhesive 3748 VO Typical Performance Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Two Pound Dead Load Heat Resistance (3M TM C 3093)(1) 175F (79C) Overlap Shear Strength @ 70F (21C) (3M TM C 3096)(2) FR-4 to FR-4 Fir to Fir Polypropylene to Polypropylene Polyethylene to Polyethylene 215 psi 275 psi 250 psi 220 psi 180 Peel Adhesion (3M TM C 3168)(1) Wire Mesh to FR-4 to PP to PE to Fir 38 piw 35 piw 27 piw 26 piw Weight Loss by TMA (In Air) Temperature of weight loss at 5C/min Thermal Coefficient of Expansion by TMA Over -100 to -40C temperature range Over -20 to 25C temperature range Thermal Conductivity (@ 41C [107F] on .020" samples) BTU-ft./ft2-hr. - F Cal./sec. - cm - C Watt/m - C J/cm - sec - C Thermal Shock Resistance Potted Washer Olyphant test (3M TM C3167) + 100C (air) to -40C (liquid) 1% @ 459F (237C) 5% @ 621F (327C) 10% @ 673F (356C) -34.0 x 10-6 units/units/C 154.5 x 10-6 units/units/C 1.11 x 10-1 4.58 x 10-4 1.92 x 10-1 1.92 x 10-3 Passes 5 cycles w/o cracking (1) 1" x 4" Douglas Fir specimens are bonded with hot melt adhesive using a 1" overlap shear configuration. Bonds are then conditioned for 24 hours at 70F (22C), 50% relative humidity before testing. Bonds are subjected to 2 lbs. per square inch load at 100F (49C) for 30 minutes. Temperature of the bond line is raised every 30 minutes until failure. Heat resistance recorded is the last temperature prior to bond failure. (2) 1" x 4" Douglas Fir specimens are bonded with hot melt adhesive using a 1" overlap and 13 mil wire spacer to set bond line thickness. Bonds are then conditioned for 24 hours at 70F (22C), 50% relative humidity before testing. Bonds are pulled in shear at a separation bond speed of 2 inch a minute recording strength at failure. (3) Test involves bonding .020" wire mesh (galvanized window screen type) to substrate using hot melt adhesive. Wire mesh is encapsulated with adhesive. After conditioning, bond is tested by 180 peel back method using Instron at 10 inches per minute peel speed. -2- 3MTM Self-Extinguishing Hot Melt Adhesive 3748 VO Typical Electrical Properties Typical Corrosion Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz 100 MHz Dielectric Constant (ASTM D 150) 2.3 2.3 2.3 2.3 2.3 2.3 Dissipation Factor (ASTM D 150) .002 .001 .001 .001 .001 .001 Dielectric Strength (ASTM D 149) 1400 volts/mil (11 mil sample) Volume Resistivity (ASTM D 257) 6.0 x 1017 ohm-cm Surface Resistivity (ASTM D 257) 4.5 x 1017 ohm/sq. Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Per ASTM D 3482 (35C/96% RH/45 v.d.c/15 days) Pass - No electrolytic corrosion. Per TM C 708* (45C/96% RH/250 v.d.c/5 days) Pass - No electrolytic corrosion. Very minor surface oxidation of test wire. Pass - No aluminum, brass or steel corrosion or discoloration. Per Mil S-46163 (10 days/50% RH/23C) *Test involves placing two #36 AWG (.005") oxygen free bare copper wires on clean 1" x 4" glass slides in fixed position 1/4" apart. Adhesive is coated over the wires and over the area between the wires in a uniform manner and cured/set. The test specimen is then subjected to 45C / 96% relative humidity / 250 volts d.c. for 5 days. The aged specimen is then visually examined for corrosion/attack of the copper surface Typical Solvent Resistance Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 1 Hour 30 Days Acetone A B Isopropyl Alcohol A B Freon(R) TF B C Freon(R) TMC B C 1, 1, 1 - trichloroethylene B C RMA Flux A B Key: A = No attack B = Slight Surface Attack/Softness C = Severe Attack/Breakup -3- 3MTM Self-Extinguishing Hot Melt Adhesive 3748 VO Storage Store below 120F (49C). Shelf Life When stored at the recommended conditions, this product has a shelf life of 2 years from the date of manufacture. Precautionary Information Refer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501. Product Use All statements, technical information and recommendations contained in this document are based upon tests or experience that 3M believes are reliable. However, many factors beyond 3M's control can affect the use and performance of a 3M product in a particular application, including the conditions under which the product is used and the time and environmental conditions in which the product is expected to perform. Since these factors are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user's method of application. Warranty and Limited Remedy Unless stated otherwise in 3M's product literature, packaging inserts or product packaging for individual products, 3M warrants that each 3M product meets the applicable specifications at the time 3M ships the product. Individual products may have additional or different warranties as stated on product literature, package inserts or product packages. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's application. If the 3M product is defective within the warranty period, your exclusive remedy and 3M's and seller's sole obligation will be, at 3M's option, to replace the product or refund the purchase price. Limitation of Liability Except where prohibited by law, 3M and seller will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. ISO 9001: 2000 This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards. 3 Industrial Business Industrial Adhesives and Tapes Division 3M Center, Building 21-1W-10, 900 Bush Avenue St. Paul, MN 55144-1000 800-362-3550 * 877-369-2923 (fax) www.3M.com/Adhesives Recycled Paper 40% pre-consumer 10% post-consumer -4- 3M is a trademark of 3M. Freon is a registered trademark of E.I. DuPont de Nemours Co. Printed in U.S.A. (c)3M 2015 78-6900-9915-1 (8/06) Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: 3M: 3748VOPG