MTP103 MTP103, Transponder ________________________________________________________________________ Applications Telecommunications: Multiplex's MTP103 transponder incorporates its MTRX192L 10Gb/s photoreceiver with an integrated limiting amplifier and its MTX-EML optical transmitter into a compact package that measures only 2.5"x3.5"x0.5". The MTX-EML transmitter can be configured with either Tunable EML (MTX-TEML, 16channel 10Gb/s tunable EML transmitter), or fixedwavelength EMLs such as the MTX510EW (1550nm), or the MTX310EW (1310nm). The pin-out of the MTP103 is 300-pin MSA (Multi Source Agreement) compliant. At the receiving side, the incoming data stream is received at 10Gb/s through the MTRX192L, which converts it into a 10Gb/s electrical data stream. The signal is then demultiplexed into sixteen channels of electrical data at 622Mb/s, and the data clock is restored using the clock recovery circuit within the demultiplexer chip. The parallel output data is then sent out to the 300pin connector. At the transmitting side, 16 parallel 622Mb/s electrical data channels are multiplexed into a 10Gb/s series data stream and sent to the EML transmitter (can be Tunable EML, 1550nm fixed-wavelength EML, or 1310nm fixedwavelength EML.) The EML transmitter then converts the electrical data into 10Gb/s optical signal. Multiplex's MTP103 transponder can be used for either short, or intermediate reach applications. The MTP103 supports transmission link distance upto 40km and beyond. Due to the high performance of the MTRX192L receiver and MTX EML's, The MTP103 transponder has extremely high sensitivity, far better than MSA's requirements, exceptionally good eye diagram and jitter performance. Version 1.0 Multiplex, Inc. * Inter- and intra-office SONET/SDH * Subscriber loop * Metropolitan area networks * O/E interface for optical add-/dropmodule sensing * Optical add-/drop-multiplexing High-speed Data Communications: * 10Gb/s Ethernet * WAN Features * Optional TXREFCLK jitter filter circuit * Integration of EML module and MTRX192L photoreceiver with MUX/DEMUX at 10Gb/s * Compact package: 2.5" x 3.5" x 0.5" * 300 pin MSA compliant * GR-253 SR-1, SR-2, IR-1, IR-2 Applications * Up to 40km transmission link and beyond * Receiver sensitivity far exceeds MSA's requirements * Low power consumption * Maintenance Controls, Alarms and Monitoring indicators, LsPOWMON, RxPOWMON, etc. * Compliant to GR-253, ITU-T G.957, ITU-G691 * OIF-SFI4-01.0 compliant SERDES's I/O timing * Operational Case temperature range: 0C to 65C Page 1 of 31 MTP103 Data Sheet Tracking and Revision September 06, 2001 / Revision 0.1 -Data Sheet created. February 04, 2002 / Revision 0.2 February 15, 2002 / Revision 1.0 - Change from preliminary to version 1.0 Version 1.0 Multiplex, Inc. Page 2 of 31 MTP103 Transponder Functional Description MTP103 Transponder is designed to provide a SONET or SDH compliant electro-optical interface between the SONET/SDH photonic physical layer and the electrical section layer. The following figure shows a block diagram for the transponder module. The module contains a 10 Gb/s optical transmitter,a 10 Gb/s optical receiver, and a Mux/DeMux chip set in the same physical package to provide sixteen 622 Mb/s LVDS channels on both Input and output side. MTP103,10 Gb/s Transponder Block Diagram RxREFCLK RxMCLK RxSIGALM RxLCKREF Fiber RX TIA+LA DMUX 1:16 10 Gb/s Ser CDR RxLOCKERR 16 Data Out RxPOCLK RxRESET TxRESET 16 Data In Fiber EML TX 10 Gb/s Ser MUX 16:1 TxPCLK TxPICLKSEL PLL TxMCLK TxLOCKERR Microprocessor Control & Laser Control Circuit TxFIFOERR TxREFCLK TxRESET TxALMINT LsENABLE TxPICLK TxREFSEL TxFIFOERR LsTEMPALM LsBIASALM I2C I/O Alarms & Controls RxPOW ALM RxALMINT ALMINT MDI/O Version 1.0 Multiplex, Inc. Page 3 of 31 MTP103 Technical Specifications Minimum and maximum values specified over operating case temperature range at 50% duty cycle data signal. Typical values are measured at room temperature unless otherwise noted. Absolute Maximum Ratings Specification as compliant with GR-253, GR-1377, ITU-T G.957, G.691 and OIF-SFI4-01.0 Parameter Symbol Min Typ Max Unit Storage Ambient Temperature TS -40 85 C Relative Humidity (non-condensing) RH -- 85 % +3.3 V Supply Voltage VCC1 -0.5 3.6 V -5.2 V Supply Voltage -6 0.5 V VEE +5.0 V Supply Voltage -0.5 +6 V VCC2 +1.8 V Supply Voltage -0.5 +2.0 V VCC3 Electro-Static Discharge (ESD) ESD -- 500 V Comments Human Body Model Recommended Operating Condition All min and max parameters are specified End-of Life within the overall relevant operating case temperature range 0 oC to +65oC unless otherwise stated. The typical values are referenced to +25oC, nominal power supply, beginning of life. Customer should use an heat sink to assure the case temperature is within the recommended operating limits. Parameter Operating Air Temperature Operating Case Temperature Transponder Total Power Consumption +3.3 V Supply Voltage +3.3 Supply Current +5.0 V Supply Voltage +5.0 Supply Current -5.2 V Supply Voltage -5.2 Supply Current +1.8 V Supply Voltage +1.8 Supply Current Reference Clock Frequency Stability Symbol PTOT Vcc1 Min 0 3.135 Icc1 Vcc2 Icc2 VEE Iee Vcc3 Icc3 4.75 -4.94 1.71 Typ 5 3.3 0.2 5.0 0.2 -5.2 0.36 1.8 0.77 Reference Clock Frequency Stability Max 65 20 Unit C C W V A V A V A V A ppm 100 ppm 3.465 1 5.25 -5.46 1.89 Comments Typ. @25C, Note 1 Noise 50 mVpp (6kHz to 2MHz) Max. @ 65 C Noise 50 mVpp (6kHz to 2MHz) Noise 50 mVpp (6kHz to 2MHz) Noise 50 mVpp (6kHz to 2MHz) For SONET Applications GR-253-Issue 3 For System applications follow OIF OIF -SFI-4-01.0 Note: 1. See the following Power consumption section for more details. Version 1.0 Multiplex, Inc. Page 4 of 31 MTP103 Power consumption Power consumptions and current consumptions from Power supplies Air Temp. C -10 22.5 44.2 59 70 Case Temp. C -4.6 27.5 49 65 77.3 5.0V_TX A 0.181 0.18 0.179 0.177 0.176 3.3V_TX A 0.222 0.142 0.416 0.668 0.89 1.8V_TX A 0.29 0.29 0.29 0.28 0.28 -5.2V_TX A 0.218 0.217 0.209 0.207 0.21 5.0V_RX A 0.014 0.014 0.014 0.014 0.014 3.3V_RX A 0.088 0.088 0.087 0.086 0.086 1.8V_RX A 0.49 0.48 0.47 0.47 0.47 -5.2V _RX A 0.154 0.152 0.151 0.149 0.149 Power W 5.3364 5.0338 5.8649 6.6444 7.3876 Figure, MTP103, Power Supply Currents vs Case Temperature 1 0.9 Power Supply Current (A) 0.8 3.3V_TX 0.7 5.0V_TX 0.6 1.8V_TX -5.2V_TX 0.5 5.0V_RX 3.3V_RX 0.4 1.8V_RX 0.3 -5.2V_RX 0.2 0.1 0 -4.6 27.5 49 65 77.3 Case Temperature, (Degree C) Figure, MTP103, Power Consumption vs Case Temperature 10 9 Power Consumption (W) 8 7 6 POWER 5 4 3 2 1 0 -4.6 27.5 49 65 77.3 Case Temperature, (Degree C) Version 1.0 Multiplex, Inc. Page 5 of 31 MTP103 Transmitter and Receiver Optical Specifications: SR1: (0 to 12 Km) Parameter Transmitter (Note 2) Fiber Output Power (modulated) Center Wavelength Dispersion Penalty BER = 1 x 10-12 Extinction Ratio Jitter Generation Peak to Peak RMS Receiver (Note 1) Receiver sensitivity Optical input overload Input optical reflectance Symbol Min Typ Max Unit Comments Ppk -4 1290 8.2 - 0 1330 1 - dBm nm dB dB 10 Gb/s Note2 0 DP ERRF Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 0 27 -17.5 - Jitter Tolerance Jitter Transfer -12 - dBm dBm dB 10Gb/s. BER at 1x10-12, PRBS: 231-1 Error free operation Excluding reflection from optical connector Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 SR2: (0 to 12 Km) Parameter Transmitter (Note 2) Fiber Output Power (modulated) Center Wavelength Dispersion Penalty BER = 1 x 10-12 Extinction Ratio Jitter Generation Peak to Peak RMS Receiver (Note 1) Receiver sensitivity Optical input overload Input optical reflectance Symbol Min Typ Max Unit Comments Ppk -4 1530 8.2 - 0 1565 2 - dBm nm dB dB 10 Gb/s Note2 0 DP ERRF Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 0 27 -17.5 - Jitter Tolerance Jitter Transfer -12 - dBm dBm dB 10Gb/s. BER at 1x10-12 , PRBS: 231-1 Error free operation Excluding reflection from optical connector Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 Notes: 1. Reference to the datasheet of MTRX192L for receiver performance in details. 2. Reference to the datasheet of MTX510EW,MTX310EW, MTX-TEML for transmitter laser performance in details. Version 1.0 Multiplex, Inc. Page 6 of 31 MTP103 IR1: (12 to 40 Km) based on 300 MSA Parameter Transmitter (Note 2) Fiber Output Power (modulated) Center Wavelength Dispersion Penalty BER = 1 x 10-12 Extinction Ratio Jitter Generation Peak to Peak RMS Receiver (Note 1) Receiver sensitivity Optical input overload Input optical reflectance Symbol Min Typ Max Unit Comments Ppk +1 1290 8.2 - +2 1330 1 - dBm nm dB dB 10 Gb/s Note2 0 DP ERRF Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 -3 27 -17.5 0 - Jitter Tolerance Jitter Transfer -13 - dBm dBm dB 10Gb/s. BER at 1x10-12, PRBS: 231-1 Error free operation Excluding reflection from optical connector Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 IR2: (12 to 40 Km) based on 300 MSA Parameter Transmitter (Note 2) Fiber Output Power (modulated) Center Wavelength Dispersion Penalty BER = 1 x 10-12 Extinction Ratio Jitter Generation Peak to Peak RMS Receiver (Note 1) Receiver sensitivity Optical input overload Input optical reflectance Symbol Min Typ Max Unit Comments Ppk -1 1530 8.2 - +2 1565 2 - dBm nm dB dB 10 Gb/s Note2 0 DP ERRF Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 -3 27 -17.5 0 - Jitter Tolerance Jitter Transfer -14 - dBm dBm dB 10Gb/s. BER at 1x10-12, PRBS: 231-1 Error free operation Excluding reflection from optical connector Compliant with GR-253-Issue 3 Compliant with GR-253-Issue 3 Notes: 3. Reference to the datasheet of MTRX192L for receiver performance in details. 4. Reference to the datasheet of MTX510EW,MTX310EW, MTX-TEML for transmitter laser performance in details. Version 1.0 Multiplex, Inc. Page 7 of 31 MTP103 General Electrical Specifications: Parameter LVDS Input Pin Characteristics Symbol Min Typ Max Unit Input Common Mode Voltage 0 1200 2400 mV Avg (Vina,Vinb) Input Peak Differential Voltage 100 - 800 mV |Vina - Vinb| Differential Input Impedance 80 100 120 - - 1475 mV Rload = 100 1 % 925 - - mV Rload = 100 1 % LVDS Output Pin Characteristics Output High Voltage Output Low Voltage Comments f = 250 MHz Output Differential Voltage 250 - 400 mV Rload = 100 1 % Output Offset Voltage 1125 - 1275 mV Rload = 100 1 % Data Rise Time, 20% to 80% 200 450 ps Zload = 100 1 % Data Fall Time, 20% to 80% 200 450 ps Zload = 100 1 % Clock Rise Time, 20% to 80% 100 450 ps Zload = 100 1 % Clock Fall Time, 20% to 80% 100 450 ps Zload = 100 1 % Reference Clock Input (RxREFCLK, TxREFCLK), AC-Coupled, Internally Biased and Terminated LVPECL single-ended peak-to-peak 200 900 mV voltage swing LVPECL differential input resistance Rdiff 80 100 120 LVDS Output Pin AC Timing Characteristics TxPICLK P/N Duty Cycle 40 50 60 % Clock Period - 1.6 - ns Clock Period - 6.4 - ns 40 50 60 % - 1.6 - ns Vcc1 - 1.0 Vcc1 V GND 1.0 V Output High Voltage Vcc1 - 1.0 Vcc1 V Output Low Voltage GND 0.5 V All signals differential RxPOCLK P/N , 622 M Hz (Note 1,2 ) Duty Cycle Clock Period CMOS Input Pin Characteristics Input High Voltage Input Low Voltage All signals differential CMOS Output Pin Characteristics LVTTL Input Pin Characteristics Input High Voltage 2.0 Vcc1 V GND 0.8 V Output High Voltage 2.4 Vcc1 V Output Low Voltage GND 0.4 V Input Low Voltage LVTTL Output Pin Characteristics Note: 1. 2. Based on SONET (GR-253-issue 3) 622 MHz clock rate. Reference to Transmit (Fig. 1) and Receive (Fig. 2) Timing diagram for more details. Version 1.0 Multiplex, Inc. Page 8 of 31 MTP103 Receive Timing Diagram: Receiver Timing Diagram in SONET Application (GR-253-issue3) Parameter RxPOCLK T0 RxPOCLK Duty Cycle RxPOCLK Rise Time RxPOCLK Fall Time RxDout Setup Time RxDout Hold Time Tcq-min, Tcq-max Symbol RT0 RTW/RT0 RTr RTf RDTs RDTh Data/Clock skew Min 45 100 100 300 300 Typ 1.6 50 Max Unit ns % ps ps ps ps ps 55 300 300 250/250 Comments 622.080 MHz 20% - 80% 20% - 80% Data Valid Window To Clock Trailing Edge Data Valid Window From Clock Trailing Edge RxDout [0 : 15] P/N RDTs Tcq-max RDTh Tcq-m in RXPOCLK P/N RTW RT0 Figure 1 Version 1.0 Multiplex, Inc. Page 9 of 31 MTP103 Transmit Timing Diagram: Transmit at 622 MHz Mode in SONET Application (GR-253-issue3) Parameter TxPICLK T0 TxPICLK Duty Cycle TxPICLK Rise Time TxPICLK Fall Time TxDin Setup Time TxDin Hold Time Symbol TT0 TTW/TT0 TTr TTf TDTs TDTh Min 45 100 100 300 300 Typ 1.6 50 Max Unit ns % ps ps ps ps 55 300 300 - Comments 622.080 MHz 20% - 80% 20% - 80% Data Valid Window To Clock Leading Edge Data Valid Window From Clock Leading Edge TxDin [0 : 15] P/N TDTs TDTh TXPICLK P/N TTW TT0 Figure 2 Version 1.0 Multiplex, Inc. Page 10 of 31 MTP103 Analog signal characteristics Parameter Input power monitor voltage slope for PIN Input power monitor voltage slope for APD Input signal monitor voltage slope for PIN Input signal monitor voltage slope for APD Normalized laser power monitor voltage BOL 50% variation of laser power Laser disable mode Laser monitor bias voltage slope Laser monitor bias offset voltage Normalized laser temperature monitor voltage Normalized laser temperature monitor slope Note: 1. 2. Symbol RxPOWMON RxPOWMON RxSIGMON RxSIGMON Min 0.8 LsPOWMON 0.44 LsBIASMON -20 17.8 -20 Typ TBD TBD TBD 0.5 Max 1.26 Unit V/mW V/mW TBD TBD V Comments Linear slop TBD V mV mV/mA mV V TBD mV/oC 0.56 0.25 LsTEMPMON 20 +20 22.5 +20 Note 1 Note 1 Note 1 Note 1 TBD Note 2 Range of optical power over which these specifications remain valid are for further study. LsTEMPMON is typically required for laser modules with TECs (thermal electric coolers). Version 1.0 Multiplex, Inc. Page 11 of 31 MTP103 Alarms response time Parameter Tx Laser bias current alarm activation time Tx Laser bias current alarm deactivation time Tx Laser temperature alarm activation time Tx Laser temperature alarm deactivation time Tx Loss of lock of TxPLL activation time Tx Loss of lock of TxPLL deactivation time Tx Mux FIFO error indicator activation time Tx Mux FIFO error indicator deactivation time Tx error indicator activation time Tx error indicator deactivation time Symbol LsBIASALM LsTEMPALM TxLOCKERR TxFIFOERR TxALMINT Rx Loss of average optical power alarm activation time Rx Loss of average optical power alarm deactivation time Rx Loss of average optical power alarm deviation Rx Loss of a.c. optical power alarm activation time Rx Loss of a.c. optical power alarm deactivation time Rx Loss of a.c. optical power alarm deviation Rx Loss of lock of RxPOCLK activation time Rx Loss of lock of RxPOCLK deactivation time Rx error indicator activation time Rx error indicator deactivation time Module error indicator activation time Module error indicator deactivation time Note: 3. Min RxPOWALM LsTEMPALM 1 RxSIGALM 1 RxLOCKERR RxALMINT ALMINT Typ Max 10 10 10 10 TBD TBD TBD TBD TBD TBD Unit ms ms ms ms ms ms ms ms ms ms 10 10 2 TBD TBD 2 TBD TBD TBD TBD TBD TBD ms ms dB ms ms dB ms ms ms ms ms ms Comments Note 3 Note 3 The minimum value represents a 1 dB hysteresis on the alarm. The maximum value indicates a 1 dB hysteresis and a 1 dB tolerance allowed for the RxPOWMON slope. Version 1.0 Multiplex, Inc. Page 12 of 31 MTP103 Transponder Pin I/O Map TOP view from user PCB K J H G F E D C B A 1 5.0VAnalog NUC Frame_GND RxDout12P 1.8VDigital RxDout8P Digital_GND RxDout4P Digital_GND RxDout0P 2 5.0VAnalog FFU Frame_GND RxDout12N 1.8VDigital RxDout8N Digital_GND RxDout4N Digital_GND RxDout0N 3 RxRATESEL1 FFU Digital_GND RxPOWMON Digital_GND FFU Digital_GND FFU Digital_GND 4 3.3VAnalog NUC Frame_GND RxDout13P 3.3VDigital RxDout9P Digital_GND RxDout5P Digital_GND RxDout1P 5 3.3VAnalog NUC Frame_GND RxDout13N 3.3VDigital RxDout9N Digital_GND RxDout5N Digital_GND RxDout1N 6 RxRESET NUC NUC Digital_GND RxPOWALM Digital_GND FFU Digital_GND NUC Digital_GND 7 FFU FFU Analog_GND RxDout14P 3.3VDigital RxDout10P Digital_GND RxDout6P Digital_GND RxDout2P 8 FFU FFU Analog_GND RxDout14N 3.3VDigital RxDout10N Digital_GND RxDout6N Digital_GND RxDout2N 9 NUC NUC FFU Digital_GND NUC Digital_GND FFU Digital_GND RxLCKREF Digital_GND 10 -5.2VAnalog FFU Analog_GND RxDout15P -5.2VDigital RxDout11P Digital_GND RxDout7P Digital_GND RxDout3P 11 -5.2VAnalog FFU Analog_GND RxDout15N -5.2VDigital RxDout11N Digital_GND RxDout7N Digital_GND RxDout3N 12 NUC NUC FFU Digital_GND NUC Digital_GND FFU Digital_GND NUC Digital_GND 13 -5.2VAnalog FFU Analog_GND FFU -5.2VDigital RxPOCLKP Digital_GND RxMCLKP Digital_GND RxREFCLKP 14 -5.2VAnalog RxALMINT Analog_GND FFU -5.2VDigital RxPOCLKN Digital_GND RxMCLKN Digital_GND RxREFCLKN 15 I2CCLOCK NUC ALMINT Digital_GND RxREFSEL Digital_GND FFU Digital_GND RxLOCKERR Digital_GND 16 5.0VAnalog TxALMINT Analog_GND TxDin12P 1.8VDigital TxDin8P Digital_GND TxDin4P Digital_GND TxDin0P 17 5.0VAnalog FFU Analog_GND TxDin12N 1.8VDigital TxDin8N Digital_GND TxDin4N Digital_GND TxDin0N 18 I2CDATA NUC NUC Digital_GND LsBIASMON Digital_GND LsPOWMON Digital_GND TxSKEWSEL0 Digital_GND 19 3.3VAnalog MDI Analog_GND TxDin13P 3.3VDigital TxDin9P Digital_GND TxDin5P Digital_GND TxDin1P 20 3.3VAnalog MDO Analog_GND TxDin13N 3.3VDigital TxDin9N Digital_GND TxDin5N Digital_GND TxDin1N 21 TxRATESEL0 TxRATESEL1 NUC Digital_GND LsENABLE Digital_GND LsTEMPMON Digital_GND TxSKEWSEL1 Digital_GND 22 3.3VAnalog FFU Analog_GND TxDin14P 3.3VDigital TxDin10P Digital_GND TxDin6P Digital_GND TxDin2P 23 3.3VAnalog FFU Analog_GND TxDin14N 3.3VDigital TxDin10N Digital_GND TxDin6N Digital_GND TxDin2N 24 TxRESET NUC NUC Digital_GND LsBIASALM Digital_GND NUC Digital_GND NUC Digital_GND 25 -5.2VAnalog NUC Frame_GND TxDin15P -5.2VDigital TxDin11P Digital_GND TxDin7P Digital_GND TxDin3P 26 -5.2VAnalog NUC Frame_GND TxDin15N -5.2VDigital TxDin11N Digital_GND TxDin7N Digital_GND TxDin3N 27 NUC NUC NUC Digital_GND LsTEMPALM Digital_GND NUC Digital_GND TxPICKSEL Digital_GND 28 -5.2VAnalog FFU Frame_GND TxPICLKP -5.2VDigital TxPCLKP Digital_GND TxMCLKP Digital_GND TxREFCLKP 29 -5.2VAnalog NUC Frame_GND TxPICLKN -5.2VDigital TxPCLKN Digital_GND TxMCLKN Digital_GND TxREFCLKN 30 TxFIFOERR NUC NUC Digital_GND TxREFSEL Digital_GND FFU Digital_GND TxLOCKERR Digital_GND RxRATESEL0 Note: 1. Receiver power & GND supplies Transmitter power & GND supplies NUC: no user connection Receiver d.c. signals Transmitter d.c. signals FFU: reserved for future use 622 differential signals d.c. signals, available in MTP Italics: optional feature RECEIVER SIDE TRANSMITER SIDE See Appendix A for 300 MSA I/O Map Version 1.0 Multiplex, Inc. Page 13 of 31 MTP103 Transponder Control and Alarm Signals Tables Pin # Symbol K3 RxRATESEL0 I K6 RxRESET I K9 K12 NUC K15 I2CCLOCK I K18 J1 J3 I2CDATA NUC I/O RxRATESEL1 J14 RxALMINT J19 J20 H6 MDI MDO H15 ALMINT F3 RxPOWMON F6 RxPOWALM F9 F12 NUC F15 RxREFSEL B6 NUC B9 RxLCKREF B12 NUC B15 RxLOCKERR I O Version 1.0 NUC NUC NUC Pin # Symbol RX Bit Rate select (LSB) RX asynchronous system reset No User Connection No User Connection K21 TxRATESEL0 I K24 TxRESET I K27 K30 NUC TxFIFOERR O I2C Clock J16 TxALMINT OD J21 J29 H18 TxRATESEL1 NUC I NUC TX Bit Rate select (LSB) TX asynchronous system reset No User Connection Mux FIFO error indicator TX Alarm, "OR" for all TX alarms TX Bit Rate select (MSB) No User Connection No User Connection H21 NUC No User Connection H24 H27 H30 NUC No User Connection No User Connection No User Connection F18 LsBIASMON A Laser bias current monitor F21 LsENABLE I Laser Enable F24 LsBIASALM O Laser bias current alarm F27 F30 LsTEMPALM TxREFSEL O I Laser temperature alarm Select TxREFCLK frequency D18 LsPOWMON A Laser output power monitor D21 LsTEMPMON A Laser temperature monitor D24 NUC No User Connection D27 NUC B18 TxSKEWSEL0 I B21 TxSKEWSEL1 I B24 NUC B27 TxPICKSEL I B30 TxLOCKERR O No User Connection Adjusts Skew, TxPICLK (LSB) Adjusts Skew, TxPICLK (MSB) No User Connection Selects speed of input TxPICLK Loss of Lock, TxPLL I/O I/O Bidirectional Bidirectional I2C Data No User Connection I RX Bit Rate select (MSB) Rx Alarm, "OR" for all OD RX alarms Serial Communication Port , RX I O Serial Communication Port, TX No User Connection Alarm for all Rx and Tx OD alarms A Receiver power monitor Loss of RX average O power alarm No User Connection No User Connection Select RxREFCLK I frequency No User Connection Locks RxPOCLK to I RxREFCLK No User Connection Loss of Lock, RxPOCLK O (active low) MSA Required Festures MTX Enable Features MSA Optional Features Inputs LVTTL Output, LVTTL Multiplex, Inc. NUC NUC Page 14 of 31 MTP103 Transponder Control Signals and Alarm Tables RX Control Signals Truth Table RX Control Signals Truth Table RxRATESEL1 1 RxRATESEL0 0 0 X (Don't Care) 1 1 Sets Rx Clock 10 Gb Ethernet rate of 10.3 Gb/s FEC, 10.664 Gb/s, or 10.7 Gb/s SONET rate of 9.95 Gb/s RxRESET 0 Asynchrounus Demux system reset 1 Normal operation RxREFSEL: Select RxREFCLK input frequency base on RxRATESEL[1:0] RxREFSEL 1 0 1 0 1 0 1 0 RxRATESEL1 1 1 1 1 0 0 0 0 RxRATESEL0 1 1 0 0 x x x x ALMLINT 0 Alarm active 1 Normal operation RxPOWALM 0 Alarm active 1 Normal operation RxLOCKERR 0 Loss of PLL Lock 1 Normal operation RxREFCLK (MHz) 622.08 155.52 644.53 161.13 666.51 (10.664 GHz) 166.63 (10.664 GHz) 669.32 (10.709 GHz) 167.33 (10.709 GHz) RxLCKREF 0 Locks RxPOCLK to RxREFCLK 1 Normal operation Version 1.0 Multiplex, Inc. Page 15 of 31 MTP103 Transponder Control Signals and Alarm Tables TX Control Signals Truth Table TxRATESEL1 1 TxRATESEL0 0 0 X (Don't Care) 1 1 TX Alarm Signals Truth Table Sets Tx Clock 10 Gb Ethernet rate of 10.3 Gb/s FEC, 10.664 Gb/s or 10.7 Gb/s SONET rate of 9.95 Gb/s LsENABLE 0 Normal operation 1 Laser Disable TxRESET 0 Asynchrounus Mux system reset 1 Normal operation LsBIASALM 0 Laser bias alarm active 1 Normal operation TxPICKSEL 0 TxPICLK, 622 MHz 1 TxPICLK, 311 MHz Available only in 311 MHz TxPICLK mode TxSKEWSEL1 TxSKEWSEL0 Adjust Skew, TxPICLK Delay, TxPICLK, 915 ps 0 0 Delay, TxPICLK, 1015 ps 0 1 Delay, TxPICLK, 715 ps 1 0 Delay, TxPICLK, 815 ps 1 1 TxREFSEL: Select TxREFCLK input frequency base on TxRATESEL[1:0] TxREFSEL 1 0 1 0 1 0 1 0 TxRATESEL1 1 1 1 1 0 0 0 0 Version 1.0 TxRATESEL0 1 1 0 0 x x x x TxFIFOERR 0 Mux FIFO error 1 Normal operation RxREFCLK (MHz) 622.08 155.52 644.53 161.13 666.51 (10.664 GHz) 166.63 (10.664 GHz) 669.32 (10.709 GHz) 167.33 (10.709 GHz) Multiplex, Inc. LsTEMPALM 0 Laser temperature alarm active 1 Normal operation TxLOCKERR 0 Loss of PLL lock 1 Normal operation TxALMINT 0 Indicates Tx alarm active 1 Normal operation Page 16 of 31 MTP103 Transponder I/O Pin Description Row A Description Pin Number I/O Logic Level A1 RxDout0P Symbol O LVDS RX Channel 0 Data Output P Description A2 RxDout0N O LVDS RX Channel 0 Data Output N A3 Digital_GND G GND Digital Ground A4 RxDout1P O LVDS RX Channel 1 Data Output P A5 RxDout1N O LVDS RX Channel 1 Data Output N A6 Digital_GND G GND Digital Ground A7 RxDout2P O LVDS RX Channel 2 Data Output P A8 RxDout2N O LVDS RX Channel 2 Data Output N A9 Digital_GND G GND Digital Ground A10 RxDout3P O LVDS RX Channel 3 Data Output P A11 RxDout3N O LVDS RX Channel 3 Data Output N A12 Digital_GND G GND Digital Ground A13 RxREFCLKP I A.C. Coupled LVPECL RX Reference Clock input P A14 RxREFCLKN I A.C. Coupled LVPECL RX Reference Clock input N A15 Digital_GND G GND Digital Ground A16 TxDin0P I LVDS TX Channel 0 Data Input P A17 TxDin0N I LVDS TX Channel 0 Data Input N A18 Digital_GND G GND Digital Ground A19 TxDin1P I LVDS TX Channel 1 Data Input P A20 TxDin1N I LVDS TX Channel 1 Data Input N A21 Digital_GND G GND Digital Ground A22 TxDin2P I LVDS TX Channel 2 Data Input P A23 TxDin2N I LVDS TX Channel 2 Data Input N A24 Digital_GND G GND Digital Ground A25 TxDin3P I LVDS TX Channel 3 Data Input P A26 TxDin3N I LVDS TX Channel 3 Data Input N A27 Digital_GND G GND Digital Ground A28 TxREFCLKP I A.C. Coupled LVPECL TX Reference Clock Input P A29 TxREFCLKN I A.C. Coupled LVPECL TX Reference Clock Input N A30 Digital_GND G Version 1.0 GND Multiplex, Inc. Digital Ground Page 17 of 31 MTP103 Row B Description Pin Number Symbol I/O Logic Level Description B1 Digital_GND G GND Digital Ground B2 Digital_GND G GND Digital Ground B3 FFU - - B4 Digital_GND G GND Digital Ground B5 Digital_GND G GND Digital Ground B6 NUC - - B7 Digital_GND G GND Digital Ground B8 Digital_GND G GND Digital Ground Reserve for future use no user connection B9 RxLCKREF I LVTTL B10 Digital_GND G GND Digital Ground B11 Digital_GND G GND Digital Ground B12 NUC - - B13 Digital_GND G GND Digital Ground B14 Digital_GND G GND Digital Ground B15 RxLOCKERR O LVTTL B16 Digital_GND G GND Digital Ground B17 Digital_GND G GND Digital Ground B18 TxSKEWSEL0 I LVTTL B19 Digital_GND G GND Digital Ground B20 Digital_GND G GND Digital Ground B21 TxSKEWSEL1 I LVTTL B22 Digital_GND G GND B23 Digital_GND G GND B24 NUC - - B25 Digital_GND G GND Digital Ground B26 Digital_GND G GND Digital Ground B27 TxPICKSEL I LVTTL B28 Digital_GND G GND Digital Ground B29 Digital_GND G GND Digital Ground B30 TxLOCKERR O LVTTL Version 1.0 Multiplex, Inc. Locks RxPOCLK to RxREFCLK no user connection Loss of Lock, RxPOCLK (active low) Adjusts Skew, TxPICLK (LSB) Adjusts Skew, TxPICLK (MSB) Digital Ground Digital Ground no user connection Selects speed of input TxPICLK Loss of Lock, TxPLL Page 18 of 31 MTP103 Row C Description Pin Number I/O Logic Level C1 RxDout4P Symbol O LVDS RX Channel 4 Data Output P Description C2 RxDout4N O LVDS RX Channel 4 Data Output N C3 Digital_GND G GND Digital Ground C4 RxDout5P O LVDS RX Channel 5 Data Output P C5 RxDout5N O LVDS RX Channel 5 Data Output N C6 Digital_GND G GND Digital Ground C7 RxDout6P O LVDS RX Channel 6 Data Output P C8 RxDout6N O LVDS RX Channel 6 Data Output N C9 Digital_GND G GND Digital Ground C10 RxDout7P O LVDS RX Channel 7 Data Output P C11 RxDout7N O LVDS RX Channel 7 Data Output N C12 Digital_GND G GND Digital Ground C13 RxMCLKP O LVDS VCO derived output RX CLK P C14 RxMCLKN O LVDS VCO derived output RX CLK N C15 Digital_GND G GND Digital Ground C16 TxDin4P I LVDS TX Channel 4 Data Input P C17 TxDin4N I LVDS TX Channel 4 Data Input N C18 Digital_GND G GND Digital Ground C19 TxDin5P I LVDS TX Channel 5 Data Input P C20 TxDin5N I LVDS TX Channel 5 Data Input N C21 Digital_GND G GND Digital Ground C22 TxDin6P I LVDS TX Channel 6 Data Input P C23 TxDin6N I LVDS TX Channel 6 Data Input N C24 Digital_GND G GND Digital Ground C25 TxDin7P I LVDS TX Channel 7 Data Input P C26 TxDin7N I LVDS TX Channel 7 Data Input N C27 Digital_GND G GND Digital Ground C28 TxMCLKP O LVDS VCO derived output TX CLK P C29 TxMCLKN O LVDS VCO derived output TX CLK N C30 Digital_GND G GND Digital Ground Version 1.0 Multiplex, Inc. Page 19 of 31 MTP103 Row D Description Pin Number I/O Logic Level D1 Digital_GND Symbol G GND Digital Ground Description D2 Digital_GND G GND Digital Ground D3 FFU - - D4 Digital_GND G GND D5 Digital_GND G GND D6 FFU - - D7 Digital_GND G GND Digital Ground D8 Digital_GND G GND Digital Ground Reserve for future use Digital Ground Digital Ground Reserve for future use D9 FFU - - D10 Digital_GND G GND Digital Ground D11 Digital_GND G GND Digital Ground D12 FFU - - D13 Digital_GND G GND D14 Digital_GND G GND D15 FFU - - D16 Digital_GND G GND Digital Ground D17 Digital_GND G GND Digital Ground D18 LsPOWMON O Analog D19 Digital_GND G GND Digital Ground D20 Digital_GND G GND Digital Ground D21 LsTEMPMON O Analog D22 Digital_GND G GND D23 Digital_GND G GND D24 NUC - - D25 Digital_GND G GND Digital Ground D26 Digital_GND G GND Digital Ground D27 NUC - - D28 Digital_GND G GND Digital Ground D29 Digital_GND G GND Digital Ground D30 FFU - - Version 1.0 Multiplex, Inc. Reserve for future use Reserve for future use Digital Ground Digital Ground Reserve for future use Laser output power monitor Laser temperature monitor Digital Ground Digital Ground no user connection no user connection Reserve for future use Page 20 of 31 MTP103 Row E Description Pin Number I/O Logic Level E1 RxDout8P Symbol O LVDS RX Channel 8 Data Output P Description E2 RxDout8N O LVDS RX Channel 8 Data Output N E3 Digital_GND G GND Digital Ground E4 RxDout9P O LVDS RX Channel 9 Data Output P E5 RxDout9N O LVDS RX Channel 9 Data Output N E6 Digital_GND G GND Digital Ground E7 RxDout10P O LVDS RX Channel 10 Data Output P E8 RxDout10N O LVDS RX Channel 10 Data Output N E9 Digital_GND G GND Digital Ground E10 RxDout11P O LVDS RX Channel 11 Data Output P E11 RxDout11N O LVDS RX Channel 11 Data Output N E12 Digital_GND G GND Digital Ground E13 RxPOCLKP O LVDS RX Parallel Clock Output P E14 RxPOCLKN O LVDS RX Parallel Clock Output N E15 Digital_GND G GND Digital Ground E16 TxDin8P I LVDS TX Channel 8 Data Input P E17 TxDin8N I LVDS TX Channel 8 Data Input N E18 Digital_GND G GND Digital Ground E19 TxDin9P I LVDS TX Channel 9 Data Input P E20 TxDin9N I LVDS TX Channel 9 Data Input N E21 Digital_GND G GND Digital Ground E22 TxDin10P I LVDS TX Channel 10 Data Input P E23 TxDin10N I LVDS TX Channel 10 Data Input N E24 Digital_GND G GND Digital Ground E25 TxDin11P I LVDS TX Channel 11 Data Input P E26 TxDin11N I LVDS TX Channel 11 Data Input N E27 Digital_GND G GND Digital Ground E28 TxPCLKP O LVDS TX Parallel Clock Input P E29 TxPCLKN O LVDS TX Parallel Clock Input N E30 Digital_GND G GND Digital Ground Version 1.0 Multiplex, Inc. Page 21 of 31 MTP103 Row F Description Pin Number I/O Logic Level F1 1.8VDigital Symbol P PWR Power Supply Description F2 1.8VDigital P PWR Power Supply F3 RxPOWMON O Analog F4 3.3VDigital P PWR F5 3.3VDigital P PWR F6 RxPOWALM O LVTTL F7 3.3VDigital P PWR Power Supply F8 3.3VDigital P PWR Power Supply Receiver power monitor Power Supply Power Supply Loss of RX average power alarm F9 NUC - - F10 -5.2VDigital P PWR Power Supply F11 -5.2VDigital P PWR Power Supply F12 NUC - - F13 -5.2VDigital P PWR Power Supply F14 -5.2VDigital P PWR Power Supply F15 RxREFSEL I LVTTL F16 1.8VDigital P PWR Power Supply F17 1.8VDigital P PWR Power Supply F18 LsBIASMON O Analog F19 3.3VDigital P PWR Power Supply F20 3.3VDigital P PWR Power Supply F21 LsENABLE I LVTTL Laser Enable F22 3.3VDigital P PWR Power Supply F23 3.3VDigital P PWR Power Supply F24 LsBIASALM O LVTTL F25 -5.2VDigital P PWR Power Supply F26 -5.2VDigital P PWR Power Supply F27 LsTEMPALM O LVTTL F28 -5.2VDigital P PWR Power Supply F29 -5.2VDigital P PWR Power Supply F30 TxREFSEL I LVTTL Version 1.0 Multiplex, Inc. no user connection no user connection Select RxREFCLK frequency Laser bias current monitor Laser bias current alarm Laser temperature alarm Select TxREFCLK frequency Page 22 of 31 MTP103 Row G Description Pin Number I/O Logic Level G1 RxDout12P Symbol O LVDS RX Channel 12 Data Output P Description G2 RxDout12N O LVDS RX Channel 12 Data Output N G3 Digital_GND G GND Digital Ground G4 RxDout13P O LVDS RX Channel 13 Data Output P G5 RxDout13N O LVDS RX Channel 13 Data Output N G6 Digital_GND G GND Digital Ground G7 RxDout14P O LVDS RX Channel 14 Data Output P G8 RxDout14N O LVDS RX Channel 14 Data Output N G9 Digital_GND G GND Digital Ground G10 RxDout15P O LVDS RX Channel 15 Data Output P G11 RxDout15N O LVDS RX Channel 15 Data Output N G12 Digital_GND G GND Digital Ground G13 FFU - - Reserve for future use G14 FFU - - Reserve for future use G15 Digital_GND G GND Digital Ground G16 TxDin12P I LVDS TX Channel 12 Data Input P G17 TxDin12N I LVDS TX Channel 12 Data Input N G18 Digital_GND G GND Digital Ground G19 TxDin13P I LVDS TX Channel 13 Data Input P G20 TxDin13N I LVDS TX Channel 13 Data Input N G21 Digital_GND G GND Digital Ground G22 TxDin14P I LVDS TX Channel 14 Data Input P G23 TxDin14N I LVDS TX Channel 14 Data Input N G24 Digital_GND G GND Digital Ground G25 TxDin15P I LVDS TX Channel 15 Data Input P G26 TxDin15N I LVDS TX Channel 15 Data Input N G27 Digital_GND G GND Digital Ground G28 TxPICLKP I LVDS TX Parallel Clock Input P G29 TxPICLKN I LVDS TX Parallel Clock Input N G30 Digital_GND G GND Digital Ground Version 1.0 Multiplex, Inc. Page 23 of 31 MTP103 Row H Description Pin Number I/O Logic Level H1 Frame_GND Symbol G GND Frame Ground Description H2 Frame_GND G GND Frame Ground H3 FFU - - H4 Frame_GND G GND H5 Frame_GND G GND H6 NUC - - H7 Analog_GND G GND Analog Ground H8 Analog_GND G GND Analog Ground Reserve for future use Frame Ground Frame Ground no user connection H9 FFU - - H10 Analog_GND G GND Analog Ground H11 Analog_GND G GND Analog Ground H12 FFU - - H13 Analog_GND G GND H14 Analog_GND G GND H15 ALMINT O LVTTL H16 Analog_GND G GND Analog Ground H17 Analog_GND G GND Analog Ground H18 NUC - - H19 Analog_GND G GND Analog Ground H20 Analog_GND G GND Analog Ground H21 NUC - - H22 Analog_GND G GND H23 Analog_GND G GND H24 NUC - - H25 Frame_GND G GND Frame Ground H26 Frame_GND G GND Frame Ground H27 NUC - - H28 Frame_GND G GND Frame Ground H29 Frame_GND G GND Frame Ground H30 NUC - - Version 1.0 Multiplex, Inc. Reserve for future use Reserve for future use Analog Ground Analog Ground Alarm for all Rx and Tx alarms no user connection no user connection Analog Ground Analog Ground no user connection no user connection no user connection Page 24 of 31 MTP103 Row J Description Pin Number I/O Logic Level J1 NUC Symbol - - no user connection Description J2 FFU - - Reserve for future use J3 RxRATESEL1 I LVTTL J4 NUC - - no user connection J5 NUC - - no user connection J6 NUC - - no user connection J7 FFU - - Reserve for future use J8 FFU - - Reserve for future use RX Bit Rate select (MSB) J9 NUC - - no user connection J10 FFU - - Reserve for future use J11 FFU - - Reserve for future use J12 NUC - - no user connection J13 FFU - - Reserve for future use J14 RxALMINT O LVTTL J15 NUC - - J16 TxALMINT O LVTTL J17 FFU - - Reserve for future use J18 NUC - - no user connection J19 MDI I LVTTL Serial Communication Port , RX J20 MDO O LVTTL Serial Communication Port, TX J21 TxRATESEL1 I LVTTL TX Bit Rate select (MSB) J22 FFU - - Reserve for future use J23 FFU - - Reserve for future use J24 NUC - - no user connection J25 NUC - - no user connection J26 NUC - - no user connection J27 NUC - - no user connection J28 FFU - - Reserve for future use J29 NUC - - no user connection J30 NUC - - no user connection Version 1.0 Multiplex, Inc. Rx Alarm, "OR" for all RX alarms no user connection TX Alarm, "OR" for all TX alarms Page 25 of 31 MTP103 Row K Description Pin Number I/O Logic Level K1 5.0VAnalog Symbol P PWR Power Supply Description K2 5.0VAnalog P PWR Power Supply K3 RxRATESEL0 I LVTTL K4 3.3VAnalog P PWR K5 3.3VAnalog P PWR K6 RxRESET I LVTTL K7 FFU - - Reserve for future use K8 FFU - - Reserve for future use no user connection RX Bit Rate select (LSB) Power Supply Power Supply RX asynchronous system reset K9 NUC - - K10 -5.2VAnalog P PWR Power Supply K11 -5.2VAnalog P PWR Power Supply K12 NUC - - K13 -5.2VAnalog P PWR Power Supply K14 -5.2VAnalog P PWR Power Supply K15 I2CCLOCK I LVTTL K16 5.0VAnalog P PWR Power Supply K17 5.0VAnalog P PWR Power Supply K18 I2CDATA I/O Analog K19 3.3VAnalog P PWR Power Supply K20 3.3VAnalog P PWR Power Supply K21 TxRATESEL0 I LVTTL K22 3.3VAnalog P PWR K23 3.3VAnalog P PWR K24 TxRESET I LVTTL K25 -5.2VAnalog P PWR Power Supply K26 -5.2VAnalog P PWR Power Supply K27 NUC - - K28 -5.2VAnalog P PWR Power Supply K29 -5.2VAnalog P PWR Power Supply K30 TxFIFOERR O LVTTL no user connection I2C Clock I2C Data TX Bit Rate select (LSB) Power Supply Power Supply TX asynchronous system reset no user connection Mux FIFO error indicator Firmware interface with I2C bus or RS232 serial port I2C and RS-232 interfaces are for further specification. Version 1.0 Multiplex, Inc. Page 26 of 31 MTP103 Mechanical Dimensions Version 1.0 Multiplex, Inc. Page 27 of 31 MTP103 Ordering Information: When ordering transponder modules, always select the appropriate options for your specific applications. Follow the below table to determine the correct order number. MTP103 b lll r cc dd - Cxxx Application b O E F M OC192 (9.95 Gb/s) 10 G Ea (10.3 Gb/s) FEC (10.7 Gb/s) Multi-Rate Laser Type lll 300 500 5xx SEML (1310 nm) EML (1550 nm) 1550 ITU Receiver Type r I PIN A APD Optical Connector cc SC SC FC FC LC LC (APC) APC Reach dd S1 SR1 S2 SR2 I1 IR1 I2 IR2 Custom Cxxx C000 Standard Note: 1. For example, to order a transponder for OC-192, 300 pin connector, short wavelength laser 1310 nm, with PIN receiver, SC optical connectors, short reach from 0 to 12 Km, and standard configuration. The correct ordering number is MTP103O300ISCS1-C000. 2. (APC), APC connector will be available in the near future. Version 1.0 Multiplex, Inc. Page 28 of 31 MTP103 Qualification and Reliability To help ensure high product reliability and customer satisfaction, MTP103 is tested using MIL-STD-883 test methods and procedures and with Telcordia Technologies requirements. This qualification program fully meets the intent of Telcordia Technologies reliability practices TR-NWT-000468 and TA-TSY-000983. Laser Safety Information Because it's small size, the safety information is not printed on the actual module. This information is, however, attached to the outside of the shipping carton. Class I and Class IIIb Laser Products All versions of the transponders are Class I laser products (output power < 1 mW), and Class IIIb laser products per CDRH, 21 CFR 1040 Laser Safety requirements. FDR/CDRH Class I and Class IIIb laser product. All versions are Class I laser products (output power < 1 mW ), and Class IIIb laser products per IEC 60825-:1993. CAUTION: Use of controls, adjustments, and procedures other than those specified herein may result in hazardous laser radiation exposure. This product complies with 21 CFR 1040.10 and 1040.11. NOTICE Unterminated optical connectors can emit laser radiation. Do not view with optical instruments. Electromagnetic Emissions and Immunity The transponder will be tested against CENELEC EN50 081 part 1 and part 2, FCC 15, Class B limits for emissions. The transponder will be tested against CENELEC EN50 082 part 1 immunity requirements. ____________________________________________________________________________________ Electrostatic Discharge Caution: This device is susceptible to damage as a result of electrostatic discharge (ESD). Take proper precautions during both handling and testing. Please follow all guidelines, such as JDEC Publications number 108-A. _____________________________________________________________________________________________ 115 Corporate Blvd. South Plainfield, NJ 07080 USA Tel: 908.757.8817 Fax: 908.757.8910 http:\\www.multiplexinc.com Version 1.0 Multiplex, Inc. Page 29 of 31 MTP103 Appendix A 300 MSA I/O Map TOP view from user PCB K J H G F E D C B A 1 5.0VAnalog RxTRACE Frame_GND RxDout12P 1.8VDigital RxDout8P Digital_GND RxDout4P Digital_GND RxDout0P 2 5.0VAnalog FFU Frame_GND RxDout12N 1.8VDigital RxDout8N Digital_GND RxDout4N Digital_GND RxDout0N 3 RxRATESEL0 RxRATESEL1 FFU Digital_GND RxPOWMON Digital_GND FFU Digital_GND FFU Digital_GND 4 3.3VAnalog NUC Frame_GND RxDout13P 3.3VDigital RxDout9P Digital_GND RxDout5P Digital_GND RxDout1P 5 NUC Frame_GND RxDout13N 3.3VDigital RxDout9N Digital_GND RxDout5N Digital_GND RxDout1N 6 RxRESET NUC RxDLOOPENB Digital_GND RxPOWALM Digital_GND FFU Digital_GND RxMUTE_Dout Digital_GND 7 FFU FFU Analog_GND RxDout14P 3.3VDigital RxDout10P Digital_GND RxDout6P Digital_GND RxDout2P 8 FFU FFU Analog_GND RxDout14N 3.3VDigital RxDout10N Digital_GND RxDout6N Digital_GND RxDout2N 9 RxMUTEPOCLK NUC FFU Digital_GND RxSIGMON Digital_GND FFU Digital_GND RxLCKREF Digital_GND 10 -5.2VAnalog FFU Analog_GND RxDout15P -5.2VDigital RxDout11P Digital_GND RxDout7P Digital_GND RxDout3P 11 -5.2VAnalog FFU Analog_GND RxDout15N -5.2VDigital RxDout11N Digital_GND RxDout7N Digital_GND RxDout3N 12 RxMUTEMCLK NUC FFU Digital_GND RxSIGALM Digital_GND FFU Digital_GND RxMCLKSEL Digital_GND 13 -5.2VAnalog FFU Analog_GND FFU -5.2VDigital RxPOCLKP Digital_GND RxMCLKP Digital_GND RxREFCLKP 14 -5.2VAnalog RxALMINT Analog_GND FFU -5.2VDigital RxPOCLKN Digital_GND RxMCLKN Digital_GND RxREFCLKN 15 I2CCLOCK NUC ALMINT Digital_GND RxREFSEL Digital_GND FFU Digital_GND RxLOCKERR Digital_GND 16 5.0VAnalog TxALMINT Analog_GND TxDin12P 1.8VDigital TxDin8P Digital_GND TxDin4P Digital_GND TxDin0P 17 5.0VAnalog FFU Analog_GND TxDin12N 1.8VDigital TxDin8N Digital_GND TxDin4N Digital_GND TxDin0N 18 I2CDATA NUC LsTUNE0 Digital_GND LsBIASMON Digital_GND LsPOWMON Digital_GND TxSKEWSEL0 Digital_GND 19 3.3VAnalog MDI Analog_GND TxDin13P 3.3VDigital TxDin9P Digital_GND TxDin5P Digital_GND TxDin1P 20 3.3VAnalog MDO Analog_GND TxDin13N 3.3VDigital TxDin9N Digital_GND TxDin5N Digital_GND TxDin1N 21 TxRATESEL0 TxRATESEL1 LsTUNE1 Digital_GND LsENABLE Digital_GND LsTEMPMON Digital_GND TxSKEWSEL1 Digital_GND 22 3.3VAnalog FFU Analog_GND TxDin14P 3.3VDigital TxDin10P Digital_GND TxDin6P Digital_GND TxDin2P 23 3.3VAnalog FFU Analog_GND TxDin14N 3.3VDigital TxDin10N Digital_GND TxDin6N Digital_GND TxDin2N 24 TxRESET NUC LsTUNE2 Digital_GND LsBIASALM Digital_GND TxPHSADJ0 Digital_GND LsTWEAK Digital_GND 25 -5.2VAnalog NUC Frame_GND TxDin15P -5.2VDigital TxDin11P Digital_GND TxDin7P Digital_GND TxDin3P 26 -5.2VAnalog NUC Frame_GND TxDin15N -5.2VDigital TxDin11N Digital_GND TxDin7N Digital_GND TxDin3N 27 TxFIFORES NUC TxLLOOPENB Digital_GND LsTEMPALM Digital_GND TxPHSADJ1 Digital_GND TxPICKSEL Digital_GND 28 -5.2VAnalog FFU Frame_GND TxPICLKP -5.2VDigital TxPCLKP Digital_GND TxMCLKP Digital_GND TxREFCLKP 29 -5.2VAnalog TxTRACE Frame_GND TxPICLKN -5.2VDigital TxPCLKN Digital_GND TxMCLKN Digital_GND TxREFCLKN 30 TxFIFOERR NUC TxLINETIMSEL Digital_GND TxREFSEL Digital_GND FFU Digital_GND TxLOCKERR Digital_GND 3.3VAnalog Version 1.0 Receiver power & GND supplies Transmitter power & GND supplies NUC: no user connection Receiver d.c. signals Transmitter d.c. signals FFU: reserved for future use 622 differential signals d.c. signals Italics: optional feature RECEIVER SIDE TRANSMITER SIDE Multiplex, Inc. Page 30 of 31 MTP103 Transponder Control and Alarm Signals Tables Pin # Symbol K3 RxRATESEL0 I Pin # Symbol K21 TxRATESEL0 I K24 TxRESET I I I RX Bit Rate select (LSB) RX asynchronous system reset Mute RxPOCLK Mute RxMCLK K27 K30 TxFIFORES TxFIFOERR I O I2CCLOCK I I2C Clock J16 TxALMINT OD K18 I2CDATA I/O J21 TxRATESEL1 I J1 RxTRACE A I2C Data Low frequency photo diode output TX Bit Rate select (LSB) TX asynchronous system reset Mux FIFO reset Mux FIFO error indicator TX Alarm, "OR" for all TX alarms TX Bit Rate select (MSB) K6 RxRESET I K9 K12 RxMUTEPOCLK RxMUTEMCLK K15 J29 TxTRACE A low frequency TX input J3 RxRATESEL1 I RX Bit Rate select (MSB) H18 LsTUNE0 I Wavelength select pin 0 (LSB) J14 RxALMINT OD Rx Alarm, "OR" for all RX alarms H21 LsTUNE1 I Wavelength select pin 1 J19 MDI I Serial Communication Port , RX H24 LsTUNE2 I J20 MDO O Serial Communication Port, TX H27 TxLLOOPENB I Wavelength select pin 2 (MSB) Line Loopback enable H30 TxLINETIMSEL I Line Timing select F18 LsBIASMON A Laser bias current monitor F21 LsENABLE I Laser Enable F24 LsBIASALM O Laser bias current alarm F27 LsTEMPALM O Laser temperature alarm F30 TxREFSEL I Select TxREFCLK frequency D18 LsPOWMON A Laser output power monitor D21 LsTEMPMON A Laser temperature monitor D24 TxPHSADJ0 I D27 TxPHSADJ1 I B18 TxSKEWSEL0 I B21 TxSKEWSEL1 I B24 LsTWEAK A B27 TxPICKSEL I B30 TxLOCKERR O I/O I/O Bidirectional Bidirectional H6 RxDLOOPENB I H15 ALMINT OD F3 RxPOWMON A F6 RxPOWALM O F9 RxSIGMON A F12 RxSIGALM O F15 RxREFSEL I B6 RxMUTE_Dout I B9 RxLCKREF I B12 RxMCLKSEL I B15 RxLOCKERR O Diagnostic Loopback enable Alarm for all Rx and Tx alarms Receiver power monitor Loss of RX average power alarm RX Signal monitor Loss of Signal, RX power alarm Select RxREFCLK frequency Mutes DeMux Data Outputs Locks RxPOCLK to RxREFCLK Selects speed of output RxMCLK Loss of Lock, RxPOCLK (active low) MSA Required Festures MSA Optional Features Inputs LVTTL Output, LVTTL I O Note: Based on 300 MSA document Version 1.0 Multiplex, Inc. Adjusts Phase, TxPCLK (LSB) Adjusts Phase, TxPCLK (MSB) Adjusts Skew, TxPICLK (LSB) Adjusts Skew, TxPICLK (MSB) DWDM Laser wavelength, fine tune Selects speed of input TxPICLK Loss of Lock, TxPLL Page 31 of 31