TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Very Low Power Consumption
D
Typical Supply Current...200 µA
(Per Amplifier)
D
Wide Common-Mode and Differential
Voltage Ranges
D
Low Input Bias and Offset Currents
D
Common-Mode Input Voltage Range
Includes VCC+
D
Output Short-Circuit Protection
D
High Input Impedance...JFET-Input Stage
D
Internal Frequency Compensation
D
Latch-Up-Free Operation
D
High Slew Rate...3.5 V/µs Typ
description
The JFET-input operational amplifiers of the
TL06_ series are designed as low-power versions
of the TL08_ series amplifiers. They feature high
input impedance, wide bandwidth, high slew rate,
and low input offset and input bias currents. The
TL06_ series feature the same terminal
assignments as the TL07_ and TL08_ series.
Each of these JFET-input operational amplifiers
incorporates well-matched, high-voltage JFET
and bipolar transistors in a monolithic integrated
circuit.
The C-suffix devices are characterized for
operation from 0°C to 70°C. The I-suffix devices
are characterized for operation from –40°C to
85°C, and the M-suffix devices are characterized
for operation over the full military temperature
range of –55°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
2
3
4
8
7
6
5
OFFSET N1
IN–
IN+
VCC–
NC
VCC+
OUT
OFFSET N2
TL061, TL061A, TL061B
D, JG, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN+
VCC–
VCC+
2OUT
2IN–
2IN+
TL062, TL062A, TL062B
D, JG, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
5
10
9
8
7
6
NC
OFFSET N1
IN–
IN+
VCC–
NC
NC
VCC+
OUT
OFFSET N2
TL061 ...U PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN–
1IN+
VCC+
2IN+
2IN–
2OUT
4OUT
4IN–
4IN+
VCC–
3IN+
3IN–
3OUT
TL064 . . . D, J, N, PW, OR W PACKAGE
TL064A, TL064B ...D OR N PACKAGE
(TOP VIEW)
•
1
2
3
4
5
10
9
8
7
6
NC
1OUT
1IN–
1IN+
VCC–
NC
VCC+
2OUT
2IN–
2IN+
TL062 ...U PACKAGE
(TOP VIEW)
•
NC – No internal connection
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
NC
2OUT
NC
2IN–
NC
3212019
910111213
4
5
6
7
8
18
17
16
15
14
NC
VCC+
NC
OUT
NC
NC
IN–
NC
IN+
NC
TL061 ...FK PACKAGE
(TOP VIEW)
NC
OFFSET N1
NC
OFFSET N2
NC NC
NC
NC
NC
3212019
910111213
4
5
6
7
8
18
17
16
15
14
4IN+
NC
VCC–
NC
3IN+
1IN+
NC
VCC+
NC
2IN+
1IN–
1OUT
NC
3OUT
3IN– 4OUT
4IN–
2IN–
2OUT
NC
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
NC
1IN–
NC
1IN+
NC
TL062 . . . FK PACKAGE
(TOP VIEW)
NC
1OUT
NC
2IN+
NC NC
NC
NC
VCC–
VCC+
TL064 . . . FK PACKAGE
(TOP VIEW)
NC – No internal connection
VCC–
AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOMAX
AT 25°CSMALL
OUTLINE
(D008)†
SMALL
OUTLINE
(D014)†
PLASTIC
DIP
(N)
PLASTIC
DIP
(P)
TSSOP
(PW)
CHIP FORM
(Y)
15 mV TL061CD TL061CP TL061CPW TL061Y
15
mV
6 mV
TL061CD
TL061ACD
TL061CP
TL061ACP
TL061CPW
TL061Y
3 mV TL061BCD TL061BCP
0°C15 mV TL062CD TL062CP TL062CPW TL062Y
to
15
mV
6 mV
TL062CD
TL062ACD
TL062CP
TL062ACP
TL062CPW
TL062Y
70°C3 mV TL062BCD TL062BCP
15 mV TL064CD TL064CN TL064CPW TL064Y
6 mV TL064ACD TL064ACN
3 mV TL064BCD TL064BCN
PACKAGE
TAVIOMAX
AT 25°CSMALL
OUTLINE
(D008)†
SMALL
OUTLINE
(D014)†
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(N)
PLASTIC
DIP
(P)
FLAT
PACK
(U)
FLAT
PACK
(W)
–40°C
TL061ID
TL061IP
40 C
to 6 mV
TL061ID
TL062ID
TL064ID TL064IN
TL061IP
TL062IP
85°C
TL062ID
TL062IP
–55°C 6 mV TL061MFK TL061MJG TL061MU
to 6 mV TL062MFK TL062MJG TL062MU
125°C 9 mV TL064MFK TL064MJ TL064MW
†The D package is available taped and reeled. Add the suffix R to the device type (e.g., TL061CDR).
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
symbol (each amplifier)
+
–
IN+
IN–
OUT
OFFSET N1
Offset Null/Compensation
TL061 Only
OFFSET N2
schematic (each amplifier)
IN+
50 Ω
100 Ω
C1
VCC+
OUT VCC–
OFFSET N1
TL061 Only
OFFSET N2
IN–
C1 = 10 pF on TL061, TL062, and TL064
Component values shown are nominal.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TL061Y chip information
This chip, when properly assembled, has characteristics similar to the TL061. Thermal compression or
ultrasonic bonding can be used on the doped-aluminum bonding pads. The chips can be mounted with
conductive epoxy or a gold-silicon preform.
Bonding-Pad Assignments
+
–OUT
IN+
IN–
VCC+
(7)
(3)
(2) (6)
(4)
VCC–
(1)
(5)
OFFSET N1
OFFSET N2
Chip Thickness: 15 Mils Typical
Bonding Pads: 4 × 4 Mils Minimum
TJ(max) = 150°C
Tolerances Are ±10%.
All Dimensions Are in Mils.
Pin (4) is Internally Connected
to Backside of Chip.
41
53
(6)
(7)
(8) (1) (2)
(3)
(4)(5)
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TL062Y chip information
This chip, when properly assembled, has characteristics similar to the TL062. Thermal compression or
ultrasonic bonding can be used on the doped-aluminum bonding pads. The chips can be mounted with
conductive epoxy or a gold-silicon preform.
Bonding-Pad Assignments
Chip Thickness: 15 Mils Typical
Bonding Pads: 4 × 4 Mils Minimum
TJ(max) = 150°C
Tolerances Are ±10%.
All Dimensions Are in Mils.
Pin (4) is Internally Connected to Backside of Chip.
+
–1OUT
1IN+
1IN–
VCC+
(8)
(6)
(3)
(2)
(5)
(1)
–
+
(7) 2IN+
2IN–
2OUT
(4)
VCC–
66
49
(6) (5)
(4)
(3)(2)(1)
(8)
(7)
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TL064Y chip information
This chip, when properly assembled, has characteristics similar to the TL064. Thermal compression or
ultrasonic bonding can be used on the doped-aluminum bonding pads. The chips can be mounted with
conductive epoxy or a gold-silicon preform.
Bonding-Pad Assignments
Chip Thickness: 15 Mils Typical
Bonding Pads: 4 × 4 Mils Minimum
TJ(max) = 150°C
Tolerances Are ±10%.
All Dimensions Are in Mils.
Pin (11) is Internally Connected
to Backside of Chip.
+
–1OUT
1IN+
1IN–
VCC+
(4)
(6)
(3)
(2)
(5)
(1)
–
+
(7) 2IN+
2IN–
2OUT
(11)
VCC–
+
–4OUT
4IN+
4IN–
(13)
(10)
(9)
(12)
(8)
–
+
(14)
3OUT 3IN+
3IN–
60
110
(13)
(14)
(1)
(2) (3) (5) (6)
(7)
(8)
(9)
(10)
(12) (11)
(4)
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
TL06_C
TL06_AC
TL06_BC TL06_I TL06_M UNIT
Supply voltage, VCC+ (see Note 1) 18 18 18 V
Supply voltage, VCC– (see Note 1) –18 –18 –18 V
Differential input voltage, VID (see Note 2) ±30 ±30 ±30 V
Input voltage, VI (see Notes 1 and 3) ±15 ±15 ±15 V
Duration of output short circuit (see Note 4) unlimited unlimited unlimited
Continuous total dissipation See Dissipation Rating Table
Storage temperature range, Tstg –65 to 150 –65 to 150 –65 to 150 °C
Case temperature for 60 seconds FK package 260 °C
Lead tem
p
erature 1 6 mm (1/16 inch) from case for 60 seconds
J, JG, U, or
300
°
C
Lead
temperat
u
re
1
,
6
mm
(1/16
inch)
from
case
for
60
seconds
,,,
W package
300
°C
Lead tem
p
erature 1 6 mm (1/6 inch) from case for 10 seconds
D, N, P, or
260
260
°
C
Lead
temperat
u
re
1
,
6
mm
(1/6
inch)
from
case
for
10
seconds
PW package
260
260
°C
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
NOTES: 1. All voltage values except differential voltages are with respect to the midpoint between VCC+ and VCC–.
2. Differential voltages are at IN+ with respect to IN–.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGE TA ≤ 25°C
POWER RATING DERATING
FACTOR DERATE
ABOVE TATA = 70°C
POWER RATING TA = 85°C
POWER RATING TA = 125°C
POWER RATING
D (8 pin) 680 mW 5.8 mW/°C 33°C 465 mW 378 mW N/A
D (14 pin) 680 mW 7.6 mW/°C 60°C 604 mW 490 mW N/A
FK 680 mW 11.0 mW/°C 88°C 680 mW 680 mW 273 mW
J 680 mW 11.0 mW/°C 88°C 680 mW 680 mW 273 mW
JG 680 mW 8.4 mW/°C 69°C 672 mW 546 mW 210 mW
N 680 mW 9.2 mW/°C 76°C 680 mW 597 mW N/A
P 680 mW 8.0 mW/°C 65°C 640 mW 520 mW N/A
PW (8 pin) 525 mW 4.2 mW/°C 25°C 336 mW N/A N/A
PW (14 pin) 700 mW 5.6 mW/°C 25°C 448 mW N/A N/A
U 675 mW 5.4 mW/°C 25°C 432 mW 351 mW 135 mW
W 680 mW 8.0 mW/°C 65°C 640 mW 520 mW 200 mW
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics, VCC±= ±15 V (unless otherwise noted)
PARAMETER TEST CONDITIONS†
TL061C
TL062C
TL064C
TL061AC
TL062AC
TL064AC UNIT
MIN TYP MAX MIN TYP MAX
VIO
In
p
ut offset voltage
V
O
= 0, TA = 25°C 3 15 3 6
mV
V
IO
Inp
u
t
offset
v
oltage
O,
RS =50 ΩT
A
= Full range 20 7.5
mV
αVIO
Temperature coef ficient V
O
= 0, R
S
=50 Ω,
10
10
µV/
°
C
α
VIO
of input offset voltage
O,S,
TA = Full range
10
10
µ
V/°C
IIO
In
p
ut offset current
VO=0
TA = 25°C 5 200 5 100 pA
I
IO
Inp
u
t
offset
c
u
rrent
V
O =
0
TA = Full range 5 3 nA
IIB
Inp t bias c rrent‡
VO=0
TA = 25°C 30 400 30 200 pA
I
IB
I
nput
bi
as current
‡
V
O =
0
TA = Full range 10 7 nA
VICR
Common-mode
TA=25
°
C
±11
–12
to
±11
–12
to
V
V
ICR input voltage range
T
A =
25°C
±11
t
o
15
±11
t
o
15
V
VOM
Maximum peak output RL = 10 kΩ, TA = 25°C±10 ±13.5 ±10 ±13.5
V
V
OM voltage swing RL ≥10 kΩ, TA = Full range ±10 ±10
V
AVD
Large-signal differential V
O
= ±10 V, TA = 25°C 3 6 4 6
V/mV
A
VD
gg
voltage amplification
O,
RL ≥10 kΩTA = Full range 3 4
V/mV
B1Unity-gain bandwidth RL = 10 kΩ, TA = 25°C 1 1 MHz
riInput resistance TA = 25°C 1012 1012 Ω
CMRR Common-mode rejection ratio VIC = VICRmin, VO = 0,
RS = 50 Ω, TA = 25°C70 86 80 86 dB
kSVR
Supply-voltage rejection ratio VCC = ±9 V to ±15 V,
VO0 RS50 Ω
70
95
80
95
dB
k
SVR
ygj
(∆VCC±/∆VIO)
V
O =
0
,
R
S =
50
Ω
,
TA = 25°C
70
95
80
95
dB
PDTotal power dissipation
(each amplifier) VO = 0,
No load TA = 25°C, 6 7.5 6 7.5 mW
ICC Supply current
(each amplifier) VO = 0,
No load TA = 25°C, 200 250 200 250 µA
VO1/VO2 Crosstalk attenuation AVD = 100, TA = 25°C 120 120 dB
†All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Full range for
TA is 0°C to 70°C for TL06_C, TL06_AC, and TL06_BC and –40°C to 85°C for TL06_I.
‡Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in
Figure 15. Pulse techniques are used to maintain the junction temperature as close to the ambient temperature as possible.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics, VCC±= ±15 V (unless otherwise noted)
PARAMETER TEST CONDITIONS†
TL061BC
TL062BC
TL064BC
TL061I
TL062I
TL064I UNIT
MIN TYP MAX MIN TYP MAX
VIO
In
p
ut offset voltage
V
O
= 0, TA = 25°C 2 3 3 6
mV
V
IO
Inp
u
t
offset
v
oltage
O,
RS =50 ΩT
A
= Full range 5 9
mV
αVIO Temperature coef ficient of
input offset voltage VO = 0, RS =50 Ω,
T
A
= Full range 10 10 µV/°C
IIO
In
p
ut offset current
VO=0
TA = 25°C 5 100 5 100 pA
I
IO
Inp
u
t
offset
c
u
rrent
V
O =
0
TA = Full range 3 10 nA
IIB
Inp t bias c rrent‡
VO=0
TA = 25°C 30 200 30 200 pA
I
IB
I
nput
bi
as current
‡
V
O =
0
TA = Full range 7 20 nA
VICR Common-mode
input voltage range TA = 25°C±11 –12
to
15 ±11 –12
to
15 V
VOM
Maximum peak output RL = 10 kΩ, TA = 25°C±10 ±13.5 ±10 ±13.5
V
V
OM voltage swing RL ≥10 kΩ, TA = Full range ±10 ±10
V
AVD
Large-signal differential V
O
= ±10 V, TA = 25°C 4 6 4 6
V/mV
A
VD
gg
voltage amplification
O,
RL ≥10 kΩTA = Full range 4 4
V/mV
B1Unity-gain bandwidth RL = 10 kΩ, TA = 25°C 1 1 MHz
riInput resistance TA = 25°C 1012 1012 Ω
CMRR Common-mode
rejection ratio VIC = VICRmin, VO = 0,
RS = 50 Ω, TA = 25°C80 86 80 86 dB
kSVR
Supply-voltage rejection ratio VCC = ±9 V to ±15 V,
VO0 RS50 Ω
80
95
80
95
dB
k
SVR
ygj
(∆VCC±/∆VIO)
V
O =
0
,
R
S =
50
Ω
,
TA = 25°C
80
95
80
95
dB
PDTotal power dissipation
(each amplifier) VO = 0,
No load TA = 25°C, 6 7.5 6 7.5 mW
ICC Supply current
(each amplifier) VO = 0,
No load TA = 25°C, 200 250 200 250 µA
VO1/VO2 Crosstalk attenuation AVD = 100, TA = 25°C 120 120 dB
†All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Full range for
TA is 0°C to 70°C for TL06_C, TL06_AC, and TL06_BC and –40°C to 85°C for TL06_I.
‡Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in
Figure 15. Pulse techniques are used to maintain the junction temperature as close to the ambient temperature as possible.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics, VCC± = ±15 V (unless otherwise noted)
PARAMETER TEST CONDITIONS†TL061M
TL062M TL064M UNIT
MIN TYP MAX MIN TYP MAX
VIO
In
p
ut offset voltage
V
O
= 0, TA = 25°C 3 6 3 9
mV
V
IO
Inp
u
t
offset
v
oltage
O,
RS =50 ΩT
A
= –55°C to 125°C 9 15
mV
αVIO Temperature coef ficient
of input offset voltage VO = 0, RS =50 Ω,
T
A
=
–55°C to 125°C10 10 µV/°C
TA = 25°C 5 100 5 100 pA
IIO Input offset current VO = 0 TA = –55°C 20* 20*
nA
TA = 125°C 20 20
nA
‡
TA = 25°C 30 200 30 200 pA
IIB Input bias current
‡
VO = 0 TA = –55°C 50* 50*
nA
TA = 125°C 50 50
nA
VICR Common-mode
input voltage range TA = 25°C±11.5 –12
to
15 ±11.5 –12
to
15 V
VOM
Maximum peak output RL = 10 kΩ, TA = 25°C±10 ±13.5 ±10 ±13.5
V
V
OM voltage swing RL ≥10 kΩ, TA = –55°C to 125°C±10 ±10
V
AVD
Large-signal differential V
O
= ±10 V, TA = 25°C 4 6 4 6
V/mV
A
VD
gg
voltage amplification
O,
RL ≥10 kΩTA = –55°C to 125°C 4 4
V/mV
B1Unity-gain bandwidth RL = 10 kΩ, TA = 25°C MHz
riInput resistance T A = 25°C 1012 1012 Ω
CMRR Common-mode
rejection ratio VIC= VICRmin, VO = 0,
RS =50 Ω, TA = 25°C80 86 80 86 dB
kSVR Supply-voltage rejection
ratio (∆VCC±/∆VIO)VCC= ±9 V to ±15 V, VO = 0,
RS =50 Ω, TA = 25°C80 95 80 95 dB
PDTotal power dissipation
(each amplifier) VO = 0,
No load TA = 25°C, 6 7.5 6 7.5 mW
ICC Supply current
(each amplifier) VO = 0,
No load TA = 25°C, 200 250 200 250 µA
VO1/VO2 Crosstalk attenuation AVD = 100, TA = 25°C 120 120 dB
* This parameter is not production tested.
†All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified.
‡Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in
Figure 15. Pulse techniques are used to maintain the junction temperature as close to the ambient temperature as possible.
operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate at unity gain (see Note 5) VI = 10 V,
CL = 100 pF, RL = 10 kΩ,
See Figure 1 2 3.5 V/µs
trRise time V
I
= 20 V, R
L
= 10 kΩ, 0.2
µs
Overshoot factor
I,
CL = 100 pF,
L,
See Figure 1 10% µ
s
VnEquivalent input noise voltage RS = 20 Ω,f = 1 kHz 42 nV/√Hz
NOTE 5: Slew rate at –55°C to 125°C is 0.7 V/µs min.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics, VCC±= ±15 V, TA = 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS†
TL061Y
TL062Y
TL064Y UNIT
MIN TYP MAX
VIO Input offset voltage VO = 0,RS = 50 Ω 315 mV
αVIO Temperature coef ficient of input offset voltage VO = 0, RS = 50 Ω10 µV/°C
IIO Input offset current VO = 0 5 200 pA
IIB Input bias current‡VO = 0 30 400 pA
VICR Common-mode input voltage range ±11 –12
to
15 V
VOM Maximum peak output voltage swing RL = 10 kΩ±10 ±13.5 V
AVD Large-signal differential voltage amplification VO = ±10 V, RL ≥ 2 kΩ3 6 V/mV
B1Unity-gain bandwidth RL = 10 kΩ1MHz
riInput resistance 1012 Ω
CMRR Common-mode rejection ratio VIC = VICRmin,
RS = 50 ΩVO = 0, 70 86 dB
kSVR
Su
pp
ly voltage rejection ratio (∆VCC±/∆VIO)
V
CC
= ±9 V to ±15 V, V
O
= 0,
70
95
dB
k
SVR
S
u
ppl
y v
oltage
rejection
ratio
(∆V
CC±
/∆V
IO
)
CC ,
RS = 50 Ω
O,
70
95
dB
PDTotal power dissipation (each amplifier) VO = 0, No load 6 7.5 mW
ICC Supply current (per amplifier) VO = 0, No load 200 250 µA
VO1/VO2 Crosstalk attenuation AVD = 100 120 dB
†All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified.
‡Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in
Figure 15. Pulse techniques are used to maintain the junction temperature as close to the ambient temperature as possible.
operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER TEST CONDITIONS
TL061Y
TL062Y
TL064Y UNIT
MIN TYP MAX
SR
Slew rate at unity gain
V
I
= 10 mV, R
L
= 10 kΩ,
15
35
V/µs
SR
Sle
w
rate
at
u
nit
y
gain
I,
CL = 100 pF,
L,
See Figure 1
1
.
5
3
.
5
V/
µ
s
trRise time V
I
= 20 V, R
L
= 10 kΩ, 0.2 µs
Overshoot factor
I,
CL = 100 pF,
L,
See Figure 1 10%
VnEquivalent input noise voltage RS = 20 Ω,f = 1 kHz 42 nV/√Hz
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
VI
RL = 2 kΩ
+
–
CL = 100 pF
OUT
Figure 1. Unity-Gain Amplifier
VI
10 kΩ
1 kΩ
RLCL = 100 pF
+
–
OUT
Figure 2. Gain-of-10 Inverting Amplifier
N2
N1
100 kΩ
1.5 kΩ
VCC–
+
–
TL061
IN –
OUT
IN +
Figure 3. Input Offset-Voltage Null Circuit
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Maximum peak output voltage vs Supply voltage 4
Maximum peak output voltage vs Free-air temperature 5
Maximum peak output voltage vs Load resistance 6
Maximum peak output voltage vs Frequency 7
Differential voltage amplification vs Free-air temperature 8
Large-signal dif ferential voltage amplification vs Frequency 9
Phase shift vs Frequency 9
Supply current vs Supply voltage 10
Supply current vs Free-air temperature 11
Total power dissipation vs Free-air temperature 12
Common-mode rejection ratio vs Free-air temperature 13
Normalized unity-gain bandwidth vs Free-air temperature 14
Normalized slew rate vs Free-air temperature 14
Normalized phase shift vs Free-air temperature 14
Input bias current vs Free-air temperature 15
Voltage-follower large-signal pulse response vs Time 16
Output voltage vs Elapsed time 17
Equivalent input noise voltage vs Frequency 18
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 4
0
0
VOM – Maximum Peak Output Voltage – V
|VCC±| – Supply Voltage – V
±2.5
±5
±7.5
±10
±12.5
±15
2 4 6 8 10 12 14 16
RL = 10 kΩ
TA = 25°C
See Figure 2
MAXIMUM PEAK OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
ÁÁ
ÁÁ
VOM
Figure 5
–75
0
VOM – Maximum Peak Output Voltage – V
TA – Free-Air Temperature – °C
±2.5
±5
±7.5
±10
±12.5
±15
–50 –25 0 25 50 75 100 125
VCC± = ±15 V
RL = 10 kΩ
See Figure 2
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
ÁÁ
ÁÁ
VOM
Figure 6
See Figure 2
TA = 25°C
VCC± = ±15 V
0100
VOM – Maximum Peak Output Voltage – V
RL – Load Resistance – Ω
1 k 10 k
±2.5
±5
±7.5
±10
±12.5
±15
200 400 700 2 k 4 k 7 k
MAXIMUM PEAK OUTPUT VOLTAGE
vs
LOAD RESISTANCE
ÁÁ
ÁÁ
VOM
VCC± = ±12 V
VCC± = ±5 V
f – Frequency – Hz
1 k
0
VOM – Maximum Peak Output Voltage – V
10 k 100 k 1 M 10 M
±2.5
±5
±7.5
±10
±12.5
±15
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREQUENCY
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
RL = 10 kΩ
TA = 25°C
See Figure 2
ÁÁ
ÁÁ
ÁÁ
VOM
ÁÁÁÁÁ
ÁÁÁÁÁ
VCC± = ±15 V
Figure 7
†Data at high and low temperatures are applicable only within the specified operating free-air temperature ranges of the various devices.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
– Differential Voltage Amplification – V/mV
AVD
RL = 10 kΩ
VCC± = ±15 V
1–75 TA – Free-Air Temperature – °C
–50 –25 0 25 50 75 100 125
2
4
10
7
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
Figure 8
AVD
(left scale)
1
.001
f – Frequency – Hz
10 100 1 k 10 k 100 k 1 M 10 M
.01
.1
1
10
100
Phase Shift
135°
90°
180°
45°
0°
VCC± = ±15 V
Rext = 0
RL = 10 kΩ
TA = 25°C
Phase Shift
(right scale)
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
– Large-Signal Differential
AVD
Voltage Amplification – V/mV
Figure 9
†Data at high and low temperatures are applicable only within the specified operating free-air temperature ranges of the various devices.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 10
TA = 25°C
No Signal
No Load
0
0
2 4 6 8 10 12 14 16
50
100
150
200
250
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
|VCC±| – Supply Voltage – V
ICC – Supply Current –
ÁÁ
ÁÁ
ÁÁ
ICC µA
±
Figure 11
–75
0
ICC – Supply Current –
TA – Free-Air Temperature – °C
50
100
150
200
250
–50 –25 0 25 50 75 100 125
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
ÁÁ
ÁÁ
ÁÁ
ICC µA
±
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
VCC± = ±15 V
No Signal
No Load
Figure 12
–75
0
TA – Free-Air Temperature – °C
5
10
15
20
25
30
–50 –25 0 25 50 75 100 125
VCC± = ±15 V
No Signal
No Load
TL064
TL062
TL061
TOTAL POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
PD – Total Power Dissipation – mW
ÁÁ
ÁÁ
PD
Figure 13
81
CMRR – Common-Mode Rejection Ratio – dB
1251007550250–25–50
TA – Free-Air Temperature – °C
–75
82
83
84
85
86
87 VCC± = ±15 V
RL = 10 kΩ
ALL EXCEPT TL06_C
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
†Data at high and low temperatures are applicable only within the specified operating free-air temperature ranges of the various devices.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
0.7
Normalized Unity-Gain Bandwidth and Slew Rate
125
1007550250–25–50 TA – Free-Air Temperature – °C
–75
0.8
0.9
1
1.1
1.2
1.3
1.02
1.01
1
0.99
0.98
0.97
Normalized Phase Shift
1.03
VCC± = ±15 V
RL = 10 kΩ
f = B1 for Phase Shift
Unity-Gain Bandwidth
(left scale) Phase Shift
(right scale)
Slew Rate
(left scale)
NORMALIZED UNITY-GAIN BANDWIDTH,
SLEW RATE, AND PHASE SHIFT
vs
FREE-AIR TEMPERATURE
Figure 14
1251007550250–25
0.01
IIB – Input Bias Current – nA
–50 TA – Free-Air Temperature – °C
0.04
0.1
0.4
1
4
10
40
100
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
ÁÁÁÁÁ
VCC± = ±15 V
ÁÁ
ÁÁ
IIB
Figure 15 Figure 16
–6
Input and Output Voltages – V
t – Time – µs
Input
Output
VCC± = ±15 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
0246810
–4
–2
0
2
4
6
VOLTAGE-FOLLOWER
LARGE-SIGNAL PULSE RESPONSE
vs
TIME
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 17
–4
– Output Voltage – mV
t – Elapsed Time – µs
0 0.2 0.4 0.6 0.8 1 1.2 1.4
0
4
8
12
16
20
24
28
VCC± = ±15 V
RL = 10 kΩ
TA = 25°C
10%
tr
Overshoot
90%
OUTPUT VOLTAGE
vs
ELAPSED TIME
VO
0
Vn – Equivalent Input Noise Voltage –
f – Frequency – Hz
10
20
30
40
50
60
70
80
90
100
10 40 100 400 1 k 4 k 10 k 40 k 100 k
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
VCC± = ±15 V
RS = 20 Ω
TA = 25°C
ÁÁ
ÁÁ
VnnV/ Hz
Figure 18
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
Table of Application Diagrams
APPLICATION DIAGRAM PART
NUMBER FIGURE
Instrumentation amplifier TL064 19
0.5-Hz square-wave oscillator TL061 20
High-Q notch filter TL061 21
Audio-distribution amplifier TL064 22
Low-level light detector preamplifier TL061 23
AC amplifier TL061 24
Microphone preamplifier with tone control TL061 25
Instrumentation amplifier TL062 26
IC preamplifier TL062 27
+
–
–
+
+
–
+
–
TL064
VCC+
VCC–
100 kΩ
Input B
10 kΩ
0.1% 0.1%
10 kΩ
VCC–
VCC+
TL064
Input A
VCC+
TL064
VCC–
100 kΩ
10 kΩ
0.1% 10 kΩ
0.1%
TL064
VCC–
VCC+
100 kΩ
100 kΩ
Output
1 MΩ
Figure 19. Instrumentation Amplifier
TL061
+
–
–15 V
15 V Output
1 kΩ
9.1 kΩ
3.3 kΩ
CF = 3.3 µF
RF = 100 kΩ
3.3 kΩ
f
+
1
2
p
RF
CF
Figure 20. 0.5-Hz Square-Wave Oscillator
TL061
+
–
R2
R1
C1 C2
R3
C3 VCC–
VCC+
OutputInput
C1
+
C2
+
C3
2
+
110 pF
fo
+
1
2
p
R1
C1
+
1kHz
R1 = R2 = 2 × R3 = 1.5 MΩ
Figure 21. High-Q Notch Filter
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
+
–
+
–
TL064 Output C
VCC+
VCC+
Output B
TL064
–
+
VCC+
Output A
TL064
–
+
VCC+
TL064
VCC+
100 kΩ
100 µF
Input
1 µF
1 MΩ
100 kΩ
100 kΩ
Figure 22. Audio-Distribution Amplifier
+
–
TIL601
10 kΩ
15 V
Output
–15 V
5 kΩ
100 pF TL061
10 kΩ
10 kΩ
10 kΩ
10 kΩ
10 kΩ
Figure 23. Low-Level Light Detector Preamplifier
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
TL061
N2
+
–
0.1 µF10 kΩ
50 Ω
250 kΩ
N1
Output
1 MΩ
VCC+
10 kΩ
10 kΩ
0.1 µF
Figure 24. AC Amplifier
1.2 MΩ100 kΩ
20 µF
+
–
0.1 µF
47 kΩTL061
2.7 kΩ
270 Ω0.003 µF 0.001 µF
0.002 µF
1 µF
10 kΩ
100 kΩ
50 kΩ
0.06 µF
50 kΩ
10 kΩ100 kΩ1 kΩ
0.06 µF
10 kΩ
0.02 µF
100 kΩ
+
Figure 25. Microphone Preamplifier With Tone Control
IN–
IN+
100 kΩ
TL062
TL062
1 kΩ1 kΩ
100 kΩ
–
+
–
+Output
Figure 26. Instrumentation Amplifier
TL061, TL061A, TL061B, TL061Y, TL062, TL062A
TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y
LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS078F – NOVEMBER 1978 – REVISED JANUAR Y 1999
22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
TL062
220 kΩ
–
+
0.00375 µF
TL062
–
+
10 pF
68 kΩ
0.003 µF
0.03 µF
0.03 µF
10 kΩ3.3 kΩ
0.003 µF
VCC–
VCC+
Output
Input
VCC–
VCC+
10 pF
MIN
MAX
100 kΩ
Treble
MIN
MAX
100 kΩ
Bass
10 kΩ
10 kΩ
+
0.01 µF27 kΩ
100 Ω
Balance 100 Ω
50 pF
+
75 µF
47 µF
5 kΩ
Gain
47 kΩ
1 µF
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
TA = 25°C
VCC± = ±15 V
Max
Treble
Max Bass
200 10 k4 k2 k1 k40040 100
20
15
10
5
0
–5
–10
–15
–20
–25 20 k
25
f – Frequency – Hz
Voltage Amplification – dB
20
IC PREAMPLIFIER RESPONSE CHARACTERISTICS
ÁÁÁ
ÁÁÁ
Min
Treble
ÁÁÁÁ
ÁÁÁÁ
Min Bass
Figure 27. IC Preamplifier
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICA TIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1998, Texas Instruments Incorporated