Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 LM5134 Single 7.6-A Peak Current Low-Side Gate Driver With a PILOT Output 1 Features 3 Description * The LM5134 is a high-speed single low-side driver capable of sinking and sourcing 7.6-A and 4.5-A peak currents. The LM5134 has inverting and noninverting inputs that give the user greater flexibility in controlling the FET. The LM5134 features one main output, OUT, and an extra gate drive output, PILOT. The PILOT pin logic is complementary to the OUT pin, and can be used to drive a small MOSFET located close to the main power FET. This configuration minimizes the turnoff loop and reduces the consequent parasitic inductance. It is particularly useful for driving high-speed FETs or multiple FETs in parallel. The LM5134 is available in the 6-pin SOT-23 package and the 6-pin WSON package with an exposed pad to aid thermal dissipation. 1 * * * * * * 7.6-A and 4.5-A Peak Sink and Source Drive Current for Main Output 820-mA and 660-mA Peak Sink and Source Current for PILOT Output 4-V to 12.6-V Single-Power Supply Matching Delay Time Between Inverting and NonInverting Inputs TTL/CMOS Logic Inputs Up to 14-V Logic Inputs (Regardless of VDD Voltage) -40C to 125C Junction Temperature Range 2 Applications * * * Motor Drivers Solid-State Power Controllers Power Factor Correction Converters Device Information(1) PART NUMBER LM5134 PACKAGE BODY SIZE (NOM) SOT-23 (6) 2.90 mm x 1.60 mm WSON (6) 3.00 mm x 3.00 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Noninverting Input Inverting Input 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 6.7 3 3 4 4 4 6 8 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics .......................................... Switching Characteristics .......................................... Typical Characteristics .............................................. Detailed Description ............................................ 12 7.1 Overview ................................................................. 12 7.2 Functional Block Diagram ....................................... 12 7.3 Feature Description................................................. 12 7.4 Device Functional Modes........................................ 12 8 Application and Implementation ........................ 14 8.1 Application Information............................................ 14 8.2 Typical Application ................................................. 14 9 Power Supply Recommendations...................... 17 10 Layout................................................................... 18 10.1 Layout Guidelines ................................................. 18 10.2 Layout Example .................................................... 18 10.3 Power Dissipation ................................................. 19 11 Device and Documentation Support ................. 20 11.1 11.2 11.3 11.4 Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 20 20 20 20 12 Mechanical, Packaging, and Orderable Information ........................................................... 20 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (April 2013) to Revision C * Added ESD Ratings table, Feature Description section, Device Functional Modes section, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. .............................................................. 1 Changes from Revision A (April 2013) to Revision B * 2 Page Page Changed layout of National Data Sheet to TI format ........................................................................................................... 18 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 5 Pin Configuration and Functions DBV Package, NGG Package 6-Pin SOT-23, 6-Pin WSON Top View VDD 1 6 IN PILOT 2 5 INB OUT 3 4 VSS Pin Functions PIN NAME NO. I/O DESCRIPTION APPLICATION INFORMATION VDD 1 -- Gate drive supply Locally decouple to VSS using low ESR/ESL capacitor located as close as possible to the IC. PILOT 2 O Gate drive output for an external turnoff FET Connect to the gate of a small turnoff MOSFET with a short, low inductance path. The turnoff FET provides a local turnoff path. OUT 3 O Gate drive output for the power FET Connect to the gate of the power FET with a short, low inductance path. A gate resistor can be used to eliminate potential gate oscillations. VSS 4 -- Ground All signals are referenced to this ground. INB 5 I Inverting logic input Connect to VSS when not used. IN 6 I Non-inverting logic input Connect to VDD when not used. EP EP -- Exposed Pad It is recommended that the exposed pad on the bottom of the package be soldered to ground plane on the PC board, and that ground plane extend out from beneath the IC to help dissipate heat. 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) Pin voltage MIN MAX VDD to VSS -0.3 14 IN, INB to VSS -0.3 14 Junction temperature, TJ -55 Storage temperature, Tstg (1) UNIT V 150 C 150 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 6.2 ESD Ratings VALUE Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 V(ESD) (1) (2) Electrostatic discharge (1) Charged-device model (CDM), per JEDEC specification JESD22C101 (2) UNIT 2000 1000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 3 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN Gate drive supply, VDD Operating junction temperature NOM MAX UNIT 4 12.6 V -40 125 C 6.4 Thermal Information LM5134 THERMAL METRIC (1) DBV (SOT-23) NGG (WSON) 6 PINS 6 PINS UNIT RJA Junction-to-ambient thermal resistance 105.9 51 C/W RJC(top) Junction-to-case (top) thermal resistance 52.1 47 C/W RJB Junction-to-board thermal resistance 21 25.3 C/W JT Junction-to-top characterization parameter 1.2 0.6 C/W JB Junction-to-board characterization parameter 20.5 24.5 C/W RJC(bot) Junction-to-case (bottom) thermal resistance N/A 5.8 C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. 6.5 Electrical Characteristics TJ = 25C, VDD = 12 V, unless otherwise specified. Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. (1). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 12.6 V POWER SUPPLY VDD VDD operating voltage TJ = -40C to +125C UVLO VDD undervoltage lockout VDD rising 4 TJ = 25C TJ = -40C to +125C VDD undervoltage lockout hysteresis IDD VDD undervoltage lockout to main output delay time VDD rising VDD quiescent current IN = INB = VDD TJ = 25C 3.6 3.25 4 V 0.36 V 500 ns 0.8 TJ = -40C to +125C 2 mA OUTPUT RON-DW (SOT23-6) RON-DW (WSON) (1) 4 Main output resistance - pulling down Main output resistance - pulling down VDD = 10 V, IOUT = -100 mA TJ = 25C VDD = 4.5 V, IOUT = -100 mA TJ = 25C VDD = 10 V, IOUT = -100 mA TJ = 25C VDD = 4.5 V, IOUT = -100 mA TJ = 25C 0.15 TJ = -40C to +125C 0.45 0.2 TJ = -40C to +125C 0.5 0.2 TJ = -40C to +125C 0.5 0.25 TJ = -40C to +125C 0.55 Power-off pulldown resistance VDD = 0 V, IOUT = -10 mA 1.5 10 Power-off pulldown clamp voltage VDD = 0 V, IOUT = -10 mA 0.7 1 V Peak sink current CL = 10,000 pF 7.6 A Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate Average Outgoing Quality Level (AOQL). Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 Electrical Characteristics (continued) TJ = 25C, VDD = 12 V, unless otherwise specified. Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only.(1). PARAMETER RON-UP (SOT23-6) RON-UP (WSON) Main output resistance pulling up Main output resistance pulling up Peak source current TEST CONDITIONS VDD = 10 V, IOUT = 50 mA TJ = 25C VDD = 4.5 V, IOUT = 50 mA TJ = 25C VDD = 10 V, IOUT = 50 mA TJ = 25C VDD = 4.5 V, IOUT = 50 mA TJ = 25C MIN TYP MAX 0.7 TJ = -40C to +125C 1.3 1 TJ = -40C to +125C 1.9 0.75 TJ = -40C to +125C 1.2 1.14 TJ = -40C to +125C 1.85 CL = 10,000 pF 4.5 UNIT A PILOT RONP-DW PILOT output resistance - pulling down Peak sink current RONP-UP PILOT output resistance - pulling up Peak source current VDD = 10 V, IOUT = -100 mA TJ = 25C VDD = 4.5 V, IOUT = -100 mA TJ = 25C 3.7 TJ = -40C to +125C 9 4.7 TJ = -40C to +125C 12 CL = 330 pF 820 VDD = 10 V, IOUT = 50 mA TJ = 25C VDD = 4.5 V, IOUT = 50 mA TJ = 25C 11 10.7 TJ = -40C to +125C 20 CL = 330 pF mA 6 TJ = -40C to +125C 660 mA LOGIC INPUT VIH Logic 1 input voltage VIL Logic 0 input voltage VHYS Logic-input hysteresis Logic-input current LM5134A, TJ = -40C to +125C 0.67 x VDD LM5134B, TJ = -40C to +125C 2.4 V LM5134A, TJ = -40C to +125C 0.33 x VDD LM5134B, TJ = -40C to +125C 0.8 LM5134A 0.9 LM5134B 0.68 INB = VDD or 0 TJ = 25C V 0.001 TJ = -40C to +125C V 10 A THERMAL RESISTANCE JA Junction to ambient SOT23-6 90 C/W WSON-6 60 C/W Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 5 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 6.6 Switching Characteristics over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT FOR VDD = +10 V tR tF OUT rise time OUT fall time CL = 1000 pF 3 CL = 5000 pF 10 CL = 10,000 pF 20 CL = 1000 pF 2 CL = 5000 pF 4.7 CL = 10,000 pF 7.2 TJ = 25C tD-ON OUT turnon propagation delay CL = 1000 pF tD-OFF OUT turnoff propagation delay CL = 1000 pF 40 ns 12 TJ = -40C to +125C Main output break-beforemake time ns 17 TJ = -40C to +125C TJ = 25C ns 25 ns 2.5 ns tPR PILOT rise time CL = 330 pF 5.3 ns tPF PILOT fall time CL = 330 pF 3.9 ns tPD-ON OUT turnoff to PILOT turnon propagation delay CL = 330 pF 4.2 ns tPD-OFF PILOT turnoff to OUT turnon propagation delay CL = 330 pF 6.4 ns FOR VDD = +4.5 V tR tF Rise time Fall time CL = 1000 pF 5 CL = 5000 pF 14 CL = 10,000 pF 24 CL = 1000 pF 2.3 CL = 5000 pF 5.4 CL = 10,00 0pF 7.2 TJ = 25C tD-ON OUT turnon propagation delay CL = 1000 pF tD-OFF OUT turnoff propagation delay CL = 1000 pF 50 ns 20 TJ = -40C to +125C Main output break-beforemake time ns 26 TJ = -40C to +125C TJ = 25C ns 45 ns 4.2 ns tPR PILOT rise time CL = 330 pF 9.6 ns tPf PILOT fall time CL = 330 pF 3.7 ns tPD-ON OUT turnoff to PILOT turnon propagation delay CL = 330 pF 7.5 ns tPD-OFF PILOT turnoff to OUT turnon propagation delay CL = 330 pF 11.8 ns 6 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 50% 50% IN tD-OFF tD-ON 90% OUT 10% tF tR tPD-OFF PILOT tPD-ON 90% 10% tPF tPR Figure 1. Timing Diagram -- Noninverting Input INB 50% 50% tD-OFF tD-ON 90% OUT 10% tF tR tPD-OFF PILOT tPD-ON 90% 10% tPF tPR Figure 2. Timing Diagram -- Inverting Input Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 7 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 6.7 Typical Characteristics 8 Figure 3. OUT Source Current vs OUT Voltage Figure 4. OUT Sink Current vs OUT Voltage Figure 5. OUT Peak Source Current vs VDD Voltage Figure 6. OUT Peak Sink Current vs VDD Voltage Figure 7. PILOT Source Current vs PILOT Voltage Figure 8. PILOT Sink Current vs PILOT Voltage Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 Typical Characteristics (continued) Figure 9. PILOT Peak Source Current vs VDD Voltage Figure 10. PILOT Peak Sink Current vs VDD Voltage Figure 11. OUT Turnon Propagation Delay vs VDD Figure 12. OUT Turnoff Propagation Delay vs VDD Figure 13. OUT Turnoff to PILOT Turnon Propagation Delay vs VDD Figure 14. PILOT Turnoff to OUT Turnon Propagation Delay vs VDD Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 9 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com Typical Characteristics (continued) 10 Figure 15. Supply Current vs OUT Capacitive Load Figure 16. Supply Current vs PILOT Capacitive Load Figure 17. Supply Current vs Frequency Figure 18. Quiescent Current vs Temperature Figure 19. LM5134A Input Threshold vs Temperature Figure 20. LM5134A Input Threshold vs Temperature Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 Typical Characteristics (continued) Figure 21. LM5134B Input Threshold vs Temperature Figure 22. LM5134B Input Threshold vs Temperature Figure 23. UVLO Threshold vs Temperature Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 11 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 7 Detailed Description 7.1 Overview The LM5134 is a single low-side gate driver with one main output, OUT, and a complementary output PILOT. The OUT pin has high 7.6-A and 4.5-A peak sink and source current and can be used to drive large power MOSFETs or multiple MOSFETs in parallel. The PILOT pin has 820-mA and 660-mA peak sink and source current, and is intended to drive an external turnoff MOSFET, as shown in Functional Block Diagram. The external turnoff FET can be placed close to the power MOSFETs to minimize the loop inductance, and therefore helps eliminate stray inductance induced oscillations or undesired turnon. This feature also provides the flexibility to adjust turnon and turnoff speed independently. 7.2 Functional Block Diagram VDD UVLO IN INB OUT DRIVER VSS PILOT VSS 7.3 Feature Description When using the external turnoff switch, it is important to prevent the potential shoot-through between the external turnoff switch and the LM5134 internal pullup switch. The propagation delay, TPD-ON and TPD-OFF, has been implemented in the LM5134 between the PILOT and the OUT pins, as depicted in the timing diagram. The turnon delay TPD-ON is designed to be shorter than the turnoff delay TPD-OFF because the rising time of the external turnoff switch can attribute to the additional delay time. It is also desirable to minimize TPD-ON to favor the fast turnoff of the power MOSFET. The LM5134 offers both inverting and noninverting inputs to satisfy requirements for inverting and non-inverting gate drive signals in a single device type. Inputs of the LM5134 are TTL and CMOS Logic compatible and can withstand input voltages up to 14 V regardless of the VDD voltage. This allows inputs of the LM5134 to be connected directly to most PWM controllers. The LM5134 includes an Undervoltage Lockout (UVLO) circuit. When the VDD voltage is below the UVLO threshold voltage, the IN and INB inputs are ignored, and if there is sufficient VDD voltage, the OUT is pulled low. In addition, the LM5134 has an internal PNP transistor in parallel with the output NMOS. Under the UVLO condition, the PNP transistor will be on and clamp the OUT voltage below 1 V. This feature ensures the OUT remains low even with insufficient VDD voltage. 7.4 Device Functional Modes Table 1 lists the logic options for the device and Table 2 lists the device truth table. 12 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 Table 1. Input/Output Options BASE PART NUMBER LOGIC INPUT LM5134A CMOS LM5134B TTL Table 2. Truth Table IN INB OUT PILOT L L L H L H L H H L H L H H L H Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 13 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information High-current gate-driver devices are required in switching power applications for a variety of reasons. To affect fast switching of power devices and reduce associated switching power losses, a powerful gate driver is employed between the PWM output of controllers and the gates of the power-semiconductor devices. Further, gate drivers are indispensable when there are times that the PWM controller cannot directly drive the gates of the switching devices. With advent of digital power, this situation is often encountered because the PWM signal from the digital controller is often a 3.3-V logic signal, which is not capable of effectively turning on a power switch. A level-shifting circuitry is needed to boost the 3.3-V signal to the gate-drive voltage (such as 12 V) to fully turn on the power device and minimize conduction losses. Because traditional buffer-drive circuits based on NPN/PNP bipolar transistors in totem-pole arrangement, being emitter-follower configurations, lack level-shifting capability, the circuits prove inadequate with digital power. Gate drivers effectively combine both the level-shifting and buffer-drive functions. Gate drivers can also perform other tasks, such as minimizing the effect of high-frequency switching noise by locating the high-current driver physically close to the power switch, driving gate-drive transformers and controlling floating power-device gates, and reducing power dissipation and thermal stress in controllers by moving gate-charge power losses into itself. Finally, emerging wide-bandgap power-device technologies, such as GaN based switches capable of supporting very high switching frequency operation, are driving special requirements in terms of gate-drive capability. These requirements include operation at low VDD voltages (5 V or lower), low propagation delays, and availability in compact, low-inductance packages with good thermal capability. In summary, gate-driver devices are extremely important components in switching power combining benefits of high-performance, low cost, component count and board space reduction with a simplified system design. 8.2 Typical Application Figure 24. Application Schematic 14 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 Typical Application (continued) 8.2.1 Design Requirements When selecting the proper gate driver device for an end application, some design considerations must first be evaluated to make the most appropriate selection. Among these considerations are input-to-output configuration, the input threshold type, bias supply voltage levels, peak source and sink currents, availability of independent enable and disable functions, propagation delay, power dissipation, and package type. Table 3. Design Parameters PARAMETER EXAMPLE VALUE Input-to-output logic Noninverting Input threshold type Logic level VDD bias supply voltage 10 V (minimum), 113 V (nominal), 15 V (peak) Peak source and sink currents Minimum 1.65-A source, minimum 1.65-A sink Enable and disable function Yes, required Propagation delay Maximum 40 ns or less 8.2.2 Detailed Design Procedure 8.2.2.1 Input-to-Output Logic The design should specify which type of input-to-output configuration should be used. If turning on the power MOSFET when the input signal is in high state is preferred, then the noninverting configuration must be selected. If turning off the power MOSFET when the input signal is in high state is preferred, the inverting configuration must be chosen. The LM5134 device can be configured in either an inverting or noninverting input-to-output configuration, using the IN- or IN+ pins, respectively. To configure the device for use in inverting mode, tie the IN+ pin to VDD and apply the input signal to the IN- pin. For the noninverting configuration, tie the IN- pin to GND and apply the input signal to the IN+ pin. 8.2.2.2 Input Threshold Type The type of controller used determines the input voltage threshold of the gate driver device. The LM5134B device features a TTL and CMOS-compatible input threshold logic, with wide hysteresis. The threshold voltage levels are low voltage and independent of the VDD supply voltage, which allows compatibility with both logic-level input signals from microcontrollers, as well as higher-voltage input signals from analog controllers. The LM5134A device features higher voltage thresholds for greater noise immunity, and controllers with higher drive voltages. See Electrical Characteristics for the actual input threshold voltage levels and hysteresis specifications for the LM5134 device. 8.2.2.3 VDD Bias Supply Voltage The bias supply voltage applied to the VDD pin of the device should never exceed the values listed in Recommended Operating Conditions. However, different power switches demand different voltage levels to be applied at the gate terminals for effective turnon and turnoff. With an operating range from 4 V to 12 V, the LM5134 device can be used to drive a variety of power switches, such as Si MOSFETs (for example, VGS = 4.5 V, 10 V, 12 V), BJTs, and wide-band gap power semiconductors (such as GaN, certain types of which allow no higher than 6 V to be applied to the gate terminals). 8.2.2.4 Peak Source and Sink Currents Generally, to minimize switching power losses, the switching speed of the power switch during turnon and turnoff should be as fast as possible. However, very fast transitions on the Drain node voltage can lead to unwanted emissions for EMI, and the turnon speed is often deliberately slowed down by placing a series resistor between the Drive output and MOSFET gate to reduce these emissions. Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 15 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com The speed at which the drain node rises during turnoff is typically dictated by the current in the inductor at turnoff, and thus is not dependent on the turnoff current of the drive circuit. However, depending on the amount of current flowing through the drain to gate capacitance of the MOSFET as the drain voltage rises and the impedance to ground of the drive circuit, it is possible for the gate voltage to exceed the threshold voltage of the FET and turn the FET back on, known as a false turnon. For these reasons, turn the FET off as fast as possible. The LM5134 allows the flexibility of different turnon and turnoff speeds, and avoids false turnon by providing a pilot output to drive a small pulldown MosFET, which can be placed close to the main FET and reduces the impedance from gate to ground on turnoff. Using the example of a power MOSFET, the system requirement for the switching speed is typically described in terms of the slew rate of the drain-to-source voltage of the power MOSFET (such as dV/dt). For example, the system requirement might state that a SPP20N60C3 power MOSFET must be turned on with a dV/dt of 20 V/ns or higher, under a DC bus voltage of 400 V in a continuous-conduction-mode (CCM) boost PFC converter application. This type of application is an inductive hard-switching application, and reducing switching power losses is critical. This requirement means that the entire drain-to-source voltage swing during power MOSFET turnon event (from 400 V in the OFF state to V DS(on) in on state) must be completed in approximately 20 ns or less. When the drain-to-source voltage swing occurs, the Miller charge of the power MOSFET (QGD parameter in SPP20N60C3 power MOSFET data sheet = 33 nC typical) is supplied by the peak current of gate driver. According to the power MOSFET inductive switching mechanism, the gate-to-source voltage of the power MOSFET at this time is the Miller plateau voltage, which is typically a few volts higher than the threshold voltage of the power MOSFET, VGS(TH). To achieve the targeted dV/dt, the gate driver must be capable of providing the QGD charge in 20 ns or less. In other words, a peak current of 1.65 A (= 33 nC / 20 ns) or higher must be provided by the gate driver. The LM5134 gate driver is capable of providing 4.5-A peak sourcing current, which exceeds the design requirement and has the capability to meet the switching speed needed. The 2.7x overdrive capability provides an extra margin against part-to-part variations in the QGD parameter of the power MOSFET, along with additional flexibility to insert external gate resistors and fine tune the switching speed for efficiency versus EMI optimizations. However, in practical designs the parasitic trace inductance in the gate drive circuit of the PCB will have a definitive role to play on the power MOSFET switching speed. The effect of this trace inductance is to limit the dI/dt of the output current pulse of the gate driver. To illustrate this, consider output current pulse waveform from the gate driver to be approximated to a triangular profile, where the area under the triangle ( 1/2 x I PEAK x time) would equal the total gate charge of the power MOSFET (QG parameter in SPP20N60C3 power MOSFET datasheet = 87 nC typical). If the parasitic trace inductance limits the dI/dt, then a situation may occur in which the full peak current capability of the gate driver is not fully achieved in the time required to deliver the QG required for the power MOSFET switching. In other words, the time parameter in the equation would dominate and the I PEAK value of the current pulse would be much less than the true peak current capability of the device, while the required QG is still delivered. Because of this, the desired switching speed may not be realized, even when theoretical calculations indicate the gate driver is capable of achieving the targeted switching speed. Thus, placing the gate driver device very close to the power MOSFET and designing a tight gate drive-loop with minimal PCB trace inductance is important to realize the full peak-current capability of the gate driver. The LM5134 is capable of driving a small FET local to the Gate of the main MOSFET to reduce the impact of this parasitic inductance and achieve the high dV/dt required on turnoff. The nominal gate voltage plateau of the SPP20N60C3 is given as 5.5 V. Thus to achieve the required sink current of 1.65 A would require an Rds_on of 3.3 for the pilot FET. Lower on resistance gives further margin in the turnoff speed as described above, and reduces the potential for false turnon. 8.2.2.5 Enable and Disable Function Certain applications demand independent control of the output state of the driver, without involving the input signal. A pin offering an enable and disable function achieves this requirement. The LM5134 device offers two input pins, IN+ and IN - , both of which control the state of the output as listed in Table 2. Based on whether an inverting or noninverting input signal is provided to the driver, the appropriate input pin can be selected as the primary input for controlling the gate driver. The other unused input pin can be used for the enable and disable functionality. If the design does not require an enable function, the unused input pin can be tied to either the VDD pin (in case IN+ is the unused pin), or GND (in case IN - is unused pin) to ensure it does not affect the output status. 16 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 8.2.2.6 Propagation Delay The acceptable propagation delay from the gate driver is dependent on the switching frequency at which it is used, and the acceptable level of pulse distortion to the system. The LM5134 device features industry best-inclass 17-ns (typical) propagation delays, which ensure very little pulse distortion and allow operation at very high frequencies. See Electrical Characteristics for the propagation and switching characteristics of the LM5134 device. 8.2.2.7 PILOT MOSFET Selection In general, a small-sized 20-V MOSFET with logic level gates can be used as the external turnoff switch. To achieve a fast switching speed and avoid the potential shoot-through, select a MOSFET with the total gate charge less than 3 nC. Verify that no shoot-through occurs for the entire operating temperature range. In addition, a small Rds(on) is preferred to obtain the strong sink current capability. The power losses of the PILOT MOSFET can be estimated in Equation 1. Pg = 1/2 x Qgo x VDD x FSW where * Qgo is the total input gate charge of the power MOSFET (1) 8.2.3 Application Curves Figure 25. OUT Turnoff to PILOT Turnon Propagation Delay vs VDD Figure 26. PILOT Turnoff to OUT Turnon Propagation Delay vs VDD 9 Power Supply Recommendations A low ESR/ESL ceramic capacitor must be connected close to the IC, between VDD and VSS pins to support the high peak current being drawn from VDD during turnon of the FETs. Place the VDD decoupling capacitor on the same side of the PC board as the driver. The inductance of via holes can impose excessive ringing on the IC pins. Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 17 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 10 Layout 10.1 Layout Guidelines Attention must be given to board layout when using LM5134. Some important considerations include: 1. The first priority in designing the layout of the driver is to confine the high peak currents that charge and discharge the FETs gate into a minimal physical area. This will decrease the loop inductance and minimize noise issues on the gate. 2. To reduce the loop inductance, the driver should be placed as close as possible to the FETs. The gate trace to and from the FETs are recommended to be placed closely side by side, or directly on top of one another. 3. The parasitic source inductance, along with the gate capacitor and the driver pulldown path, can form a LCR resonant tank, resulting in gate voltage oscillations. An optional resistor or ferrite bead can be used to damp the ringing. 10.2 Layout Example Figure 27. LM5134 Layout Example 18 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 LM5134 www.ti.com SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 10.3 Power Dissipation It is important to keep the power consumption of the driver below the maximum power dissipation limit of the package at the operating temperature. The total power dissipation of the LM5134 is the sum of the gate charge losses and the losses in the driver due to the internal CMOS stages used to buffer the output as well as the power losses associated with the quiescent current. The gate charge losses include the power MOSFET gate charge losses as well as the PILOT FET gate charge losses and can be calculated as follows: Pg = (Qgo + Qgp) x VDD x FSW (2) Or Pg = (Co + Cp) x VDD2 x FSW where * * * Fsw is switching frequency Qgo is the total input gate charge of the power MOSFET Qgp is the total input gate charge of the PILOT MOSFET (3) Co and Cp are the load capacitance at OUT and PILOT outputs respectively. It should be noted that due to the use of an external turnoff switch, part of the gate charge losses are dissipated in the external turnoff switch. Therefore, the actual gate charge losses dissipated in the LM5134 is less than predicted by the above expressions. However, they are a good conservative design estimate. The power dissipation associated with the internal circuit operation of the driver can be estimated with the characterization curves of the LM5134. For a given ambient temperature, the maximum allowable power losses of the IC can be defined using Equation 4. P = (TJ - TA) / JA where * P is the total power dissipation of the driver (4) Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 19 LM5134 SNVS808C - MAY 2012 - REVISED FEBRURARY 2016 www.ti.com 11 Device and Documentation Support 11.1 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.2 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.4 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 20 Submit Documentation Feedback Copyright (c) 2012-2016, Texas Instruments Incorporated Product Folder Links: LM5134 PACKAGE OPTION ADDENDUM www.ti.com 28-Oct-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM5134AMF/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SK7A LM5134AMFX/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SK7A LM5134ASD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 5134A LM5134ASDX/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 5134A LM5134BMF/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SK7B LM5134BMFX/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SK7B LM5134BSD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 5134B LM5134BSDX/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 5134B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 28-Oct-2017 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Dec-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ LM5134AMF/NOPB SOT-23 LM5134AMFX/NOPB LM5134ASD/NOPB Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) DBV 6 1000 178.0 SOT-23 DBV 6 3000 WSON NGG 6 1000 LM5134ASDX/NOPB WSON NGG 6 LM5134BMF/NOPB SOT-23 DBV LM5134BMFX/NOPB SOT-23 LM5134BSD/NOPB WSON LM5134BSDX/NOPB WSON NGG B0 (mm) K0 (mm) P1 (mm) 8.4 3.2 3.2 1.4 4.0 178.0 8.4 3.2 3.2 1.4 178.0 12.4 3.3 3.3 1.0 4500 330.0 12.4 3.3 3.3 6 1000 178.0 8.4 3.2 DBV 6 3000 178.0 8.4 NGG 6 1000 178.0 12.4 6 4500 330.0 12.4 Pack Materials-Page 1 W Pin1 (mm) Quadrant 8.0 Q3 4.0 8.0 Q3 8.0 12.0 Q1 1.0 8.0 12.0 Q1 3.2 1.4 4.0 8.0 Q3 3.2 3.2 1.4 4.0 8.0 Q3 3.3 3.3 1.0 8.0 12.0 Q1 3.3 3.3 1.0 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Dec-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM5134AMF/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM5134AMFX/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 LM5134ASD/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LM5134ASDX/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LM5134BMF/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM5134BMFX/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 LM5134BSD/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LM5134BSDX/NOPB WSON NGG 6 4500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NGG0006A SDE06A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM5134ASDX/NOPB LM5134BSDX/NOPB LM5134BSD/NOPB LM5134BMF/NOPB LM5134AMF/NOPB LM5134ASD/NOPB LM5134BMFX/NOPB LM5134AMFX/NOPB