MA4FCP300 Silicon Flip Chip PIN Diode V 1.00 1269 Outline Drawing Features n n n n n n n Low Series Resistance : 2.6 Low Capacitance : 45 fF Fast Switching Speed : 40 nS Silicon Nitride Passivation Polyimide Scratch Protection Designed for Automated Pick and Place Insertion Rugged by Design Top View A B F Side View D Description M/A-COM's MA4FCP Series consists of Silicon Flip Chip PIN diodes fabricated with M/A-COM's patented HMIC process. This diode is fabricated on epitaxial wafers using a process designed for repeatable electrical characteristics and extremely low parasitics. This diode is fully passivated with Silicon Nitride and has an additional layer of Polyimide for scratch protection. These protective coatings prevent damage to the junction during automated or manual handling. This flip chip configuration is suitable for pick and place insertion. E D C Bottom View Applications Cathode Mark The small 0315 outline and low 0.12 pS RC product, make the device useful for multi-throw switch and switched phase shifter circuits requiring < 40 nS switching speeds up to 18 GHz operating frequency. Absolute Maximum Ratings @ 25 C1 Nominal Die Dimensions Inches Dim Parameter Value Forward Current 100 mA Reverse Voltage -100 V Operating Temperature -55 C to +150 C Storage Temperature -55 C to +150 C Junction Temperature Dissipated Power Mounting Temperature +175 C 150 mW +300 C for 10 seconds 1. Exceeding any of these values may result in permanent damage Millimeters A Min 0.0269 Max 0.0289 Min 0.683 Max 0.733 B 0.0135 0.0155 0.343 0.393 C 0.0040 0.0080 0.102 0.203 D 0.0041 0.0061 0.105 0.155 E 0.0124 0.0144 0.315 0.365 F 0.0069 0.0089 0.175 0.225 Silicon Flip Chip PIN Diode MA4FCP300 V 1.00 Electrical Specifications @ TA = + 25 C Parameters @ Conditions Symbol Units Total Capacitance @ -10 V, 1 MHz1 CT Total Capacitance @ -10 V, 1 GHz1,3 Typ. Max. pF 0.045 0.050 CT pF 0.025 Series Resistance @ +50 mA2,3 , 100 MHz RS 2.1 Series Resistance @ +50 mA2,3 , 1 GHz RS 2.6 Forward Voltage @ +100 mA VF V 1.1 Reverse Voltage @ -10 A VR V Reverse Current @ -70 V IR nA l -100 l 50 - 90% Lifetime @ +10 mA / -6 mA TL ns 140 C/W 450 Steady State Thermal Resistance4 1. 2. 3. 4. Min. l -70 l 1.5 l -100 l Total capacitance is equivalent to the sum of junction capacitance Cj and parasitic capacitance, Cp. Series resistance RS is equivalent to the total diode series resistance including the junction resistance Rj. Rs and Cp measured on an HP4291A with die mounted in an ODS-186 package. Steady-state thermal resistance measured with die mounted in an ODS-186 package. Assembly Considerations Mounting Techniques The following precautions should be observed for successful assembly of the die. These devices were designed for insertion onto hard or soft substrates with the junction side down. They can be mounted with electrically conductive epoxy or with a low temperature solder preform. The die can also be assembled with the junction side up, and wire or ribbon bonds made to the pads. Cleanliness These chips should be handled in a clean environment. Do not attempt to clean die after installation. ESD These devices very susceptible to ESD and are rated Class 0 (0-199 V) per HBM MIL-STD-883, method 3015.7 [C = 100 pF 10%, R = 1.5k 1%]. Even though tested die pass 100 V ESD, they must be handled in a static-free environment General Handling The protective polymer coating on the active areas of these devices provides scratch protection, particularly for the metal airbridge that contacts the anode. Die can be handled with tweezers or vacuum pickups and are suitable for use with automatic pick-and-place equipment. Solder Die Attach Using Electrically Conductive Ag Epoxy and Solder These chips are designed to be inserted onto hard or soft substrates with the junction side down. They should be mounted onto silkscreened circuits using Electrically Conductive Ag Epoxy, approximately 1-2 mils in thickness and cured at approximately 90 C to 150 C per manufacturer's schedule . For extended cure times >30 minutes, temperatures must be below 200 C. Sn Rich Solders are not recommended due to the Tungsten Metallization scheme beneath the gold contacts. Indalloy or 80 Au/20 Sn Solders are acceptable. Maximum soldering temperature must be <300 C for <10 sec. 2 M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1908) 574 200, Fax+44 (1908) 574 300 Silicon Flip Chip PIN Diode MA4FCP300 V 1.00 Circuit Mounting Dimensions (Inches) 0.013 0.012 (2) PL 0.008 (2) PL Ordering Information Part Number Package MA4FCP300 Die in Carrier MA4FCP300-T Tape/Reel MA4FCP300-W Wafer on Frame Diode Model Rs _ + Ls = 0.6 nH Ct M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. 3 n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1908) 574 200, Fax+44 (1908) 574 300 Silicon Flip Chip PIN Diode MA4FCP300 V 1.00 Capacitance vs Frequency 0.08 0.07 0.06 0.05 0.04 Ct @ -10V 0.03 0.02 0.01 0.00 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 Frequency (GHz) Rs vs Frequency 5.00 4.50 4.00 3.50 3.00 Rs @ 50 mA 2.50 2.00 1.50 1.00 0.50 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 Frequency (GHz) 4 M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1908) 574 200, Fax+44 (1908) 574 300