Very Low Power/Voltage CMOS SRAM 256K X 8 bit BSI FEATURES * Wide Vcc operation voltage : 2.4V ~ 5.5V * Very low power consumption : Vcc = 3.0V C-grade : 20mA (Max.) operating current I- grade : 25mA (Max.) operating current 0.1uA (Typ.) CMOS standby current Vcc = 5.0V C-grade : 35mA (Max.) operating current I- grade : 40mA (Max.) operating current 0.6uA (Typ.) CMOS standby current * High speed access time : -70 70ns(Max.) at Vcc = 3.0V -10 100ns(Max.) at Vcc = 3.0V * Automatic power down when chip is deselected * Three state outputs and TTL compatible * Fully static operation * Data retention supply voltage as low as 1.5V * Easy expansion with CE2, CE1, and OE options * All I/O pins are 3V/5V tolerant BS62LV2001 DESCRIPTION The BS62LV2001 is a high performance, very low power CMOS Static Random Access Memory organized as 262,144 words by 8 bits and operates in a wide range of 2.4V to 5.5V supply voltage. Advanced CMOS technology and circuit techniques provide both high speed and low power features with a typical CMOS standby current of 0.1uA and maximum access time of 70ns in 3V operation. Easy memory expansion is provided by an active LOW chip enable (CE1), an active HIGH chip enable (CE2), and active LOW output enable (OE) and three-state output drivers. The BS62LV2001 has an automatic power down feature, reducing the power consumption significantly when chip is deselected. The BS62LV2001 is available in DICE form, JEDEC standard 32 pin 450mil Plastic SOP, 8mmx13.4mm STSOP, and 8mmx20mm TSOP. PRODUCT FAMILY BLOCK DIAGRAM PIN CONFIGURATIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 * A11 A9 A8 A13 WE CE2 A15 VCC A17 A16 A14 A12 A7 A6 A5 A4 * A17 A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 GND BS62LV2001TC BS62LV2001STC BS62LV2001TI BS62LV2001STI 1 2 3 4 5 6 7 BS62LV2001SC 8 BS62LV2001SI 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE1 DQ7 DQ6 DQ5 DQ4 DQ3 GND DQ2 DQ1 DQ0 A0 A1 A2 A3 A13 A17 A15 A16 A14 A12 A7 A6 A5 A4 Address Input Buffer 20 Row 1024 Memory Array 1024 x 2048 Decoder 2048 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 VCC A15 CE2 WE A13 A8 A9 A11 OE A10 CE1 DQ7 DQ6 DQ5 DQ4 DQ3 CE1 CE2 WE OE Vdd Gnd 8 8 Data Input Buffer Data Output Buffer Column I/O 8 8 Write Driver Sense Amp 256 Column Decoder 16 Control Address Input Buffer A11 A9 A8 A3 A2 A1 A0 A10 Brilliance Semiconductor Inc. reserves the right to modify document contents without notice. R0201-BS62LV2001 1 Revision 2.5 April 2002 BSI BS62LV2001 PIN DESCRIPTIONS Name Function A0-A17 Address Input These 18 address inputs select one of the 262,144 x 8-bit words in the RAM CE1 Chip Enable 1 Input CE2 Chip Enable 2 Input CE1 is active LOW and CE2 is active HIGH. Both chip enables must be active when data read from or write to the device. If either chip enable is not active, the device is deselected and is in a standby power mode. The DQ pins will be in the high impedance state when the device is deselected. WE Write Enable Input The write enable input is active LOW and controls read and write operations. With the chip selected, when WE is HIGH and OE is LOW, output data will be present on the DQ pins; when WE is LOW, the data present on the DQ pins will be written into the selected memory location. OE Output Enable Input The output enable input is active LOW. If the output enable is active while the chip is selected and the write enable is inactive, data will be present on the DQ pins and they will be enabled. The DQ pins will be in the high impedance state when OE is inactive. DQ0 - DQ7 Data Input/Output Ports These 8 bi-directional ports are used to read data from or write data into the RAM. Vcc Power Supply Gnd Ground TRUTH TABLE MODE WE CE1 CE2 OE Not selected (Power Down) X H X X X X L X Output Disabled H L H Read H L Write L L PARAMETER I CCSB, I CCSB1 H High Z I CC H L D OUT I CC H X D IN I CC OPERATING RANGE RATING UNITS -0.5 to Vcc+0.5 V V TERM Terminal Voltage with Respect to GND T BIAS Temperature Under Bias T STG Storage Temperature PT Power Dissipation 1.0 W I OUT DC Output Current 20 mA -40 to +125 -60 to +150 O O C RANGE AMBIENT TEMPERATURE Vcc Commercial 0 O C to +70 O C 2.4V ~ 5.5V Industrial C O O -40 C to +85 C 2.4V ~ 5.5V CAPACITANCE (1) (TA = 25oC, f = 1.0 MHz) SYMBOL 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. R0201-BS62LV2001 Vcc CURRENT High Z ABSOLUTE MAXIMUM RATINGS(1) SYMBOL I/O OPERATION 2 CIN CDQ PARAMETER Input Capacitance Input/Output Capacitance CONDITIONS MAX. UNIT VIN=0V 6 pF VI/O=0V 8 pF 1. This parameter is guaranteed and not tested. Revision 2.5 April 2002 BSI BS62LV2001 DC ELECTRICAL CHARACTERISTICS ( TA = 0oC to + 70oC ) PARAMETER NAME PARAMETER TEST CONDITIONS Guaranteed Input Low (2) Voltage Guaranteed Input High (2) Voltage VIL VIH MIN. Vcc=3.0V Vcc=5.0V Vcc=3.0V Vcc=5.0V TYP. (1) MAX. UNITS -0.5 -- 0.8 V 2.0 2.2 -- Vcc+0.2 V IIL Input Leakage Current Vcc = Max, VIN = 0V to Vcc -- -- 1 uA IOL Output Leakage Current Vcc = Max, CE1= VIH, CE2= VIL, or OE = VIH, VI/O = 0V to Vcc -- -- 1 uA VOL Output Low Voltage Vcc = Max, IOL = 2mA -- -- 0.4 V VOH Output High Voltage Vcc = Min, IOH = -1mA 2.4 -- -- V ICC Operating Power Supply Current CE1 = VIL, or CE2 = VIH, (3) IDQ = 0mA, F = Fmax Vcc=3.0V -- -- 20 Vcc=5.0V -- -- 35 Standby Current-TTL CE1 = VIH, or CE2 = VIL, (3) IDQ = 0mA, F = Fmax Vcc=3.0V -- -- 1 Vcc=5.0V -- -- 2 Vcc=3.0V -- 0.1 0.7 Vcc=5.0V -- 0.6 6 ICCSB ICCSB1 CE1Vcc-0.2V, CE20.2V, VINVcc-0.2V or VIN0.2V Standby Current-CMOS Vcc=3.0V Vcc=5.0V Vcc=3.0V Vcc=5.0V mA mA uA 1. Typical characteristics are at TA = 25oC. 2. These are absolute values with respect to device ground and all overshoots due to system or tester notice are included. 3. Fmax = 1/tRC . DATA RETENTION CHARACTERISTICS ( TA = 0oC to + 70oC ) SYMBOL PARAMETER TEST CONDITIONS MIN. TYP. (1) MAX. UNITS VDR Vcc for Data Retention CE1 Vcc - 0.2V, CE2 0.2V, VIN Vcc - 0.2V or VIN 0.2V 1.5 -- -- V ICCDR Data Retention Current CE1 Vcc - 0.2V, CE2 0.2V, VIN Vcc - 0.2V or VIN 0.2V -- 0.01 0.5 uA tCDR Chip Deselect to Data Retention Time 0 -- -- ns -- -- ns tR See Retention Waveform Operation Recovery Time TRC (2) 25OC 1. Vcc = 1.5V, TA = + 2. tRC = Read Cycle Time LOW VCC DATA RETENTION WAVEFORM (1) ( CE1 Controlled ) Data Retention Mode Vcc VDR 1.5V Vcc CE1 Vcc tR t CDR CE1 Vcc - 0.2V VIH VIH LOW VCC DATA RETENTION WAVEFORM (2) ( CE2 Controlled ) Data Retention Mode Vcc VDR 1.5V Vcc CE2 R0201-BS62LV2001 VIL Vcc tR t CDR CE2 0.2V 3 VIL Revision 2.5 April 2002 BSI BS62LV2001 KEY TO SWITCHING WAVEFORMS AC TEST CONDITIONS Input Pulse Levels Input Rise and Fall Times Input and Output Timing Reference Level Vcc/0V 5ns WAVEFORM INPUTS OUTPUTS MUST BE STEADY MUST BE STEADY MAY CHANGE FROM H TO L WILL BE CHANGE FROM H TO L 1269 MAY CHANGE FROM L TO H WILL BE CHANGE FROM L TO H 5PF DON T CARE: ANY CHANGE PERMITTED CHANGE : STATE UNKNOWN DOES NOT APPLY CENTER LINE IS HIGH IMPEDANCE "OFF "STATE 0.5Vcc AC TEST LOADS AND WAVEFORMS 1269 3.3V 3.3V OUTPUT , OUTPUT 100PF INCLUDING JIG AND SCOPE INCLUDING JIG AND SCOPE 1404 1404 FIGURE 1A FIGURE 1B THEVENIN EQUIVALENT 667 OUTPUT 1.73V ALL INPUT PULSES Vcc GND 90% 90% 10% 10% 5ns FIGURE 2 AC ELECTRICAL CHARACTERISTICS ( TA = 0oC to + 70oC, Vcc = 3.0V ) READ CYCLE JEDEC PARAMETER NAME PARAMETER NAME BS62LV2001-70 MIN. TYP. MAX. DESCRIPTION BS62LV2001-10 MIN. TYP. MAX. UNIT tAVAX tRC Read Cycle Time tAVQV tAA Address Access Time -- t E1LQV t ACS1 Chip Select Access Time (CE1) -- t E2HOV t ACS2 Chip Select Access Time (CE2) -- -- tGLQV tOE Output Enable to Output Valid -- -- t E1LQX t CLZ1 Chip Select to Output Low Z (CE1) 10 -- t E2HOX t CLZ2 Chip Select to Output Low Z (CE2) 10 -- -- 15 -- -- ns tGLQX tOLZ Output Enable to Output in Low Z 10 -- -- 15 -- -- ns t E1HQZ t CHZ1 Chip Deselect to Output in High Z (CE1) 0 -- 35 0 -- 40 ns tE2HQZ t CHZ1 Chip Deselect to Output in High Z (CE2) 0 -- 35 0 -- 40 ns tGHQZ tOHZ Output Disable to Output in High Z 0 -- 30 0 -- 35 ns tAXOX tOH Output Disable to Output Address Change 10 -- -- 15 -- -- ns R0201-BS62LV2001 70 4 -- -- 100 -- -- ns -- 70 -- 70 -- -- 100 ns -- -- 100 ns 70 -- -- 100 ns 35 -- -- 50 ns -- 15 -- -- ns Revision 2.5 April 2002 BSI BS62LV2001 SWITCHING WAVEFORMS (READ CYCLE) READ CYCLE1 (1,2,4) t RC ADDRESS t t t OH AA OH D OUT READ CYCLE2 (1,3,4) CE1 t ACS1 CE2 t t ACS2 t CHZ1, t (5) CLZ (5) CHZ2 D OUT READ CYCLE3 (1,4) t RC ADDRESS t AA OE t OE t OH t OLZ CE1 (5) t ACS1 t CLZ1 CE2 t OHZ (5) (1,5) t CHZ1 t ACS2 (2,5) t t CHZ2 (5) CLZ2 D OUT NOTES: 1. WE is high for read Cycle. 2. Device is continuously selected when CE1 = VIL and CE2= VIH. 3. Address valid prior to or coincident with CE1 transition low and/or CE2 transition high. 4. OE = VIL . 5. Transition is measured 500mV from steady state with CL = 5pF as shown in Figure 1B. The parameter is guaranteed but not 100% tested. R0201-BS62LV2001 5 Revision 2.5 April 2002 BSI BS62LV2001 AC ELECTRICAL CHARACTERISTICS ( TA = 0oC to + 70oC, Vcc = 3.0V ) WRITE CYCLE JEDEC PARAMETER NAME PARAMETER NAME DESCRIPTION BS62LV2001-70 MIN. TYP. MAX. BS62LV2001-10 MIN. TYP. MAX. UNIT tAVAX tWC Write Cycle Time 70 -- -- 100 -- -- ns t E1LWH tCW Chip Select to End of Write 70 -- -- 100 -- -- ns tAVWL tAS Address Set up Time 0 -- -- 0 -- -- ns tAVWH tAW Address Valid to End of Write 70 -- -- 100 -- -- ns tWLWH tWP Write Pulse Width 35 -- -- 50 -- -- ns tWHAX tWR1 Write Recovery Time (CE1 , WE) 0 -- -- 0 -- -- ns t E2LAX tWR2 Write Recovery Time (CE2) 0 -- -- 0 -- -- ns tWLOZ tWHZ Write to Output in High Z 0 -- 30 0 -- 40 ns tDVWH tDW Data to Write Time Overlap 30 -- -- 40 -- -- ns tWHDX tDH Data Hold from Write Time 0 -- -- 0 -- -- ns tGHOZ tOHZ Output Disable to Output in High Z 0 -- 30 0 -- 40 ns tWHQX tOW End of Write to Output Active 5 -- -- 10 -- -- ns SWITCHING WAVEFORMS (WRITE CYCLE) t WC WRITE CYCLE1 (1) ADDRESS (3) t WR1 OE (11) t CW (5) CE1 (5) CE2 t WE t CW (11) t WR2 AW t t AS (3) WP (2) (4,10) t OHZ D OUT t DH t DW D IN R0201-BS62LV2001 6 Revision 2.5 April 2002 BSI BS62LV2001 WRITE CYCLE2 (1,6) t WC ADDRESS (11) t CW (5) CE1 CE2 (5) (11) t t CW AW t WR2 t WP (3) (2) WE t t AS DH (4,10) t WHZ D OUT (7) (8) t DW t DH (8,9) D IN NOTES: 1. WE must be high during address transitions. 2. The internal write time of the memory is defined by the overlap of CE1 and CE2 active and WE low. All signals must be active to initiate a write and any one signal can terminate a write by going inactive. The data input setup and hold timing should be referenced to the second transition edge of the signal that terminates the write. 3. TWR is measured from the earlier of CE1 or WE going high or CE2 going low at the end of write cycle. 4. During this period, DQ pins are in the output state so that the input signals of opposite phase to the outputs must not be applied. 5. If the CE1 low transition or the CE2 high transition occurs simultaneously with the WE low transitions or after the WE transition, output remain in a high impedance state. 6. OE is continuously low (OE = VIL ). 7. DOUT is the same phase of write data of this write cycle. 8. DOUT is the read data of next address. 9. If CE1 is low and CE2 is high during this period, DQ pins are in the output state. Then the data input signals of opposite phase to the outputs must not be applied to them. 10. Transition is measured 500mV from steady state with CL = 5pF as shown in Figure 1B. The parameter is guaranteed but not 100% tested. 11. TCW is measured from the later of CE1 going low or CE2 going high to the end of write. R0201-BS62LV2001 7 Revision 2.5 April 2002 BSI BS62LV2001 ORDERING INFORMATION BS62LV2001 X X Y Y SPEED 70: 70ns 10: 100ns GRADE C: +0oC ~ +70oC I: -40oC ~ +85oC PACKAGE T: TSOP (8mm x 20mm) ST: Small TSOP (8mm x 13.4mm) S: SOP D: DICE STSOP - 32 R0201-BS62LV2001 8 Revision 2.5 April 2002 BSI BS62LV2001 PACKAGE DIMENSIONS (continued) TSOP - 32 WITH PLATING b c c1 BASE METAL b1 SECTION A-A SOP -32 R0201-BS62LV2001 9 Revision 2.5 April 2002 BSI BS62LV2001 REVISION HISTORY Revision Description Date 2.2 2001 Data Sheet release Apr. 15, 2001 2.3 Modify Standby Current (Typ. and Jun. 29, 2001 Max.) 2.4 To add DICE form March 06,2002 2.5 Modify some AC parameters. Modify 5V ICCSB1_Max(I-grade) from 10uA to 25uA. April,11,2002 R0201-BS62LV2001 10 Note Revision 2.5 April 2002