AK5365VQP - AKM Semiconductor

[AK5365]

MS0164-E-02 2012/12

- 1 -

GENERAL DESCRIPTION

AK5365 is a high-performance 24-bit, 96kHz sampling ADC for consumer audio and digital recording

applications. Thanks to AKM’s Enhanced Dual-Bit modulator architecture, this analog-to-digital converter

has an impressive dynamic range of 103dB with a high level of integration. The AK5365 has a 5-channel

stereo input selector, an input Programmable Gain Amplifier with an ALC function. All this integration with

high-performance makes the AK5365 well suited for CD and DVD recording systems.

FEATURES

1. 24bit Stereo ADC

• 5ch Stereo Inputs Selector

• Input PGA from +12dB to 0dB, 0.5dB Step

• Auto Level Control (ALC) Circuit

• Digital HPF for offset cancellation (fc=1.0Hz@fs=48kHz)

• Digital Attenuator

• Soft Mute

• Single-end Inputs

• S/(N+D) : 94dB

• DR, S/N : 103dB

• Audio I/F Format : 24bit MSB justified, I2S

2. 3-w ire Serial μP Interface / I2C-Bus

3. Master / Slave Mode

4. Master Clock : 256fs/384fs/512fs

5. Sampling Rate : 32kHz to 96kHz

6. Pow er Supply

• AVDD: 4.75 ∼ 5.25V (typ. 5.0V)

• DVDD: 3.0 ∼ 5.25V (typ. 3.3V)

7. Power Supply Current : 27mA

8. Ta = -40 ∼ 85°C

9. Package : 44pin LQFP

24-Bit 96kHz ΔΣ ADC with Selector/PGA/ALC

AK5365

[AK5365]

MS0164-E-02 2012/12

- 2 -

 Block Diagram

LIN1

LIN2

LIN3

LIN4

LIN5

RIN1

RIN2

RIN3

RIN4

RIN5

ADC HPF Audio I/F

Controller

IPGAL

ROPIN ROUT IPGAR

Control Register

I/F

CSN

CAD1 CCLK

SCL CDTI

SDA

LRCK

BICK

MCLK

SDTO

AVSS

AVDD

DVSS

DVDD

LOPIN M/S SEL2 SEL1 SEL0 PDN

LOUT ALC

IPGA

DATT

CTRL

(ALC)

SMUTE

Pre-Amp

VCOM

Block diagram

[AK5365]

MS0164-E-02 2012/12

- 3 -

 Ordering Guide

AK5365VQ −40 ∼ +85°C 44pin LQFP (0.8mm pitch)

AKD5365 Evaluation Board for AK5365

 Pin Layout

LIN5

RIN5

44 43

142 41 40 39 38 37 36 35 3433

32

31

30

29

28

27

26

25

24

23

2221201918171615141312

2

3

4

5

6

7

8

9

10

11

AK5365VQ

Top View

TEST1

LIN4

TEST2

LIN3

TEST3

LIN2

TEST4

LIN1

LOPIN

LOUT

IPGAL

IPGAR

ROUT

ROPIN

AVDD

AVSS

VCOM

DVSS

DVDD

SDTO

BICK

LRCK

MCLK

PDN

ALC

SMUTE

SEL0

SEL1

SEL2

CDTI/SDA

CCLK/SCL

CSN/CAD1

TEST8

RIN4

TEST7

RIN3

TEST6

RIN2

TEST5

RIN1

M/S

CTRL

[AK5365]

MS0164-E-02 2012/12

- 4 -

PIN/FUNCTION

No. Pin Name I/O Function

1 LIN5 I Lch Analog Input 5 Pin

2 TEST1 I Test 1 Pin (Connected to AVSS)

3 LIN4 I Lch Analog Input 4 Pin

4 TEST2 I Test 2 Pin (Connected to AVSS)

5 LIN3 I Lch Analog Input 3 Pin

6 TEST3 I Test 3 Pin (Connected to AVSS)

7 LIN2 I Lch Analog Input 2 Pin

8 TEST4 I Test 4 Pin (Connected to AVSS)

9 LIN1 I Lch Analog Input 1 Pin

10 LOPIN I Lch Feed Back Resistor Input Pin

11 LOUT O Lch Feed Back Resistor Output Pin

12 IPGAL I Lch IPGA Input Pin

13 IPGAR I Rch IPGA Input Pin

14 ROUT O Rch Feed Back Resistor Output Pin

15 ROPIN I Rch Feed Back Resistor Input Pin

16 AVDD - Analog Power Supply Pin, 4.75 ∼ 5.25V

17 AVSS - Analog Ground Pin

18 VCOM O Common Voltage Output Pin, AVDD/2

Bias voltage of ADC input.

19 DVSS - Digital Ground Pin

20 DVDD - Digital Power Supply Pin, 3.0 ∼ 5.25V

21 SDTO O Audio Serial Data Output Pin

22 BICK I/O Audio Serial Data Clock Pin

Note: All digital input pins except pull-down pins should not be left floating.

Note: TEST1, TEST2, TEST3 and TEST4 pins should be connected to AVSS.

[AK5365]

MS0164-E-02 2012/12

- 5 -

No. Pin Name I/O Function

23 LRCK I/O Output Channel Clock Pin

24 MCLK I Master Clock Input Pin

25 PDN I Power-Down Mode Pin

“H”: Power up, “L”: Power down reset and initializes the control register.

26 ALC I ALC Enable Pin (Internal Pull-down Pin, typ. 100kΩ)

“H” : ALC Enable, “L” : ALC Disable

27 SMUTE I Soft Mute Pin (Internal Pull-down Pin, typ. 100kΩ)

“H” : Soft Mute, “L” : Normal Operation

28 SEL0 I Input Selector 0 Pin

29 SEL1 I Input Selector 1 Pin

30 SEL2 I Input Selector 2 Pin

CDTI I Control Data Input Pin in 3-wire Control (CTRL pin = “L”)

31 SDA I/O Control Data Input / Output Pin in I2C Control (CTRL pin = “H”)

CCLK I Control Data Clock Pin in 3-wire Control (CTRL pin = “L”)

32 SCL I Control Data Clock Pin in I2C Control (CTRL pin = “H”)

CSN I Chip Select Pin in 3-wire Control (CTRL pin = “L”)

33 CAD1 I Chip Address 1 Select Pin in I2C Control (CTRL pin = “H”)

34 CTRL I Control Mode Pin

“H” : I2C Control & I2S Compatible, “L” : 3-wire Control

35 M/S I Master / Slave Mode Pin

“H” : Master Mode, “L” : Slave Mode

36 RIN1 I Rch Analog Input 1 Pin

37 TEST5 I Test 5 Pin (Connected to AVSS)

38 RIN2 I Rch Analog Input 2 Pin

39 TEST6 I Test 6 Pin (Connected to AVSS)

40 RIN3 I Rch Analog Input 3 Pin

41 TEST7 I Test 7 Pin (Connected to AVSS)

42 RIN4 I Rch Analog Input 4 Pin

43 TEST8 I Test 8 Pin (Connected to AVSS)

44 RIN5 I Rch Analog Input 5 Pin

Note: All digital input pins except pull-down pins should not be left floating.

Note: TEST5, TEST6, TEST7 and TEST8 pins should be connected to AVSS.

[AK5365]

MS0164-E-02 2012/12

- 6 -

ABSOLUTE MAXIMUM RATINGS

(AVSS=DVSS=0V; Note 1)

Parameter Symbol min max Unit

Power Supplies:

Analog

Digital

|AVSS – DVSS| (Note 2)

AVDD

DVDD

ΔGND

−0.3

-

6.0

0.3

V

Input Current, Any Pin Except Supplies IIN - ±10 mA

Analog Input Voltage

(VREF, LIN1-5, RIN1-5, LOPIN, ROPIN, IPGAL, IPGAR pins) VINA −0.3 AVDD+0.3 V

Digital Input Voltage (All digital input pins) VIND −0.3 DVDD+0.3 V

Ambient Temperature (powered applied) Ta −40 85 °C

Storage Temperature Tstg −65 150 °C

Note 1. All voltages with respect to ground.

Note 2. AVSS and DVSS must be connected to the same analog ground plane.

WARNING: Operation at or beyond these limits may result in permanent damage to the device.

Normal operation is not guaranteed at these extremes.

RECOMMENDED OPERATING CONDITIONS

(AVSS=DVSS=0V; Note 1)

Parameter Symbol min typ max Unit

Power Supplies

(Note 3) Analog

Digital AVDD

DVDD 4.75

3.0 5.0

3.3 5.25

AVDD V

V

Note 1. All voltages with respect to ground.

Note 3. The power up sequence between AVDD and DVDD is not critical.

WARNING: AKM assumes no responsibility for the usage beyond the conditions in this datasheet.

[AK5365]

MS0164-E-02 2012/12

- 7 -

ANALOG CHARACTERISTICS

(Ta=25°C; AVDD=5.0V, DVDD=3.3V; AVSS=DVSS=0V; fs=48kHz, 96kHz; BICK=64fs; Signal Frequency=1kHz;

24bit Data; Measurement frequency=20Hz ∼ 20kHz at fs=48kHz, 40Hz ∼ 40kHz at fs=96kHz; unless otherwise

specified)

Parameter min typ max Unit

Pre-Amp Characteristics:

Feedback Resistance 10 50 kΩ

S/(N+D) (Note 4) - 100 dB

S/N (A-weighted) - 108 dB

Load Resistance (Note 5) 6.3 kΩ

Load Capacitance 20 pF

Input PGA Characteristics:

Input Voltage (Note 6) 0.9 1 1.1 Vrms

Input Resistance (Note 7) 6.3 10 15 kΩ

Step Size 0.2 0.5 0.8 dB

Gain Control Range

ALC = OFF

ALC = ON 0

−9.5 +12

+12 dB

dB

ADC Analog Input Characteristics: IPGA=0dB, ALC = OFF (Note 8)

Resolution 24 Bits

S/(N+D) (−0.5dBFS)

fs=48kHz

fs=96kHz 84

82 94

92

dB

DR (−60dBFS)

fs=48kHz, A-weighted

fs=96kHz 96

89 103

99

dB

S/N

fs=48kHz, A-weighted

fs=96kHz 96

89 103

99

dB

Interchannel Isolation (Note 9) 90 110 dB

Interchannel Gain Mismatch 0.2 0.5 dB

Gain Drift 100 - ppm/°C

Power Supply Rejection (Note 10) 50 - dB

Power Supplies

Power Supply Current

Normal Operation (PDN pin = “H”)

AVDD

DVDD (fs=48kHz)

(fs=96kHz)

Power-down mode (PDN pin = “L”) (Note 11)

AVDD

DVDD

23

4

8

10

35

8

16

100

mA

μA

Note 4. This value is measured at LOUT and ROUT pins using the circuit as shown in Figure 24.

The input signal voltage is 2Vrms.

Note 5. This value is the input i mpedance of an external device that t he LOUT and R OUT pi ns can dri ve, when a device

is

connected with LOUT and ROUT pin externally. The feedback resistor (min. 10kΩ) that it is usually con nected

with the LOUT/ROUT pins, and the value of input impedance (min. 6.3kΩ) of the IPGAL/R pins are not

included.

Note 6. Full scale (0dB) of the input voltage at ALC=OFF and IPGA=0dB.

Input voltage to IPGAL and IPGAR pins is proportional to AVDD voltage. Vin = 0.2 x AVDD (Vrms).

Note 7. This value is input impedance of the IPGAL and IPGAR pins.

Note 8. This value is measured via the followin g path. Pre-Amp → IPGA (Gain : 0dB) → ADC.

The measurement circuit is Figure 24.

Note 9. This value is the int erchannel isolation between all the channels of t he LIN1-5 and RIN1-5 when the applied input

signal causes the Pre-Amp output to equal IPGA input.

Note 10. PSR is applied to AVDD and DVDD with 1kHz, 50mVpp.

[AK5365]

MS0164-E-02 2012/12

- 8 -

Note 11. All digital input pins are held DVDD or DVSS.

[AK5365]

MS0164-E-02 2012/12

- 9 -

FILTER CHARACTERISTICS (fs=48kHz)

(Ta=−40 ∼ 85°C; AVDD=4.75 ∼ 5.25V; DVDD=3.0 ∼ 5.25V; fs=48kHz)

Parameter Symbol min typ max Unit

ADC Digital Filter (Decimation LPF):

Passband (Note 12)

−0.005dB

−0.02dB

−0.06dB

−6.0dB

PB

0

-

21.768

22.0

24.0

21.5

-

kHz

Stopband SB 26.5 kHz

Passband Ripple PR ±0.005 dB

Stopband Attenuation SA 80 dB

Group Delay (Note 13) GD 29.6 1/fs

Group Delay Distortion ΔGD 0 μs

ADC Digital Filter (HPF):

Frequency Response (Note 12)

−3dB

−0.5dB

−0.1dB

FR

1.0

2.9

6.5

Hz

Note 12. The passband and stopband frequencies scale with fs. For example, 21.768kHz at −0.02dB is 0.454 x fs.

Note 13. The calculated delay time induced by digital filtering. This time is from the input of an analog signal

to the setting of 24bit data both channels to the ADC output register for ADC.

FILTER CHARACTERISTICS (fs=96kHz)

(Ta=−40 ∼ 85°C; AVDD=4.75 ∼ 5.25V; DVDD=3.0 ∼ 5.25V; fs=96kHz)

Parameter Symbol min typ max Unit

ADC Digital Filter (Decimation LPF):

Passband (Note 14)

−0.005dB

−0.02dB

−0.06dB

−6.0dB

PB

0

-

43.536

44.0

48.0

43.0

-

kHz

Stopband SB 53.0 kHz

Passband Ripple PR ±0.005 dB

Stopband Attenuation SA 80 dB

Group Delay (Note 15) GD 29.6 1/fs

Group Delay Distortion ΔGD 0 μs

ADC Digital Filter (HPF):

Frequency Response (Note 14)

−3dB

−0.5dB

−0.1dB

FR

2

5.8

13

Hz

Note 14. The passband and stopband frequencies scale with fs. For example, 43.536kHz at −0.02dB is 0.454 x fs.

Note 15. The calculated delay time induced by digital filtering. This time is from the input of an analog signal

to the setting of 24bit data both channels to the ADC output register for ADC.

[AK5365]

MS0164-E-02 2012/12

- 10 -

DC CHARACTERISTICS

(Ta=−40 ∼ 85°C; AVDD=4.75 ∼ 5.25V; DVDD=3.0 ∼ 5.25V)

Parameter Symbol min typ max Unit

High-Level Input Voltage

Low-Level Input Voltage VIH

VIL 70%DVDD

- -

30%DVDD V

V

High-Level Output Voltage (Iout=−400μA)

Low-Level Output Voltage

(Except SDA pin : Iout=400μA)

(SDA pin : Iout=3mA)

VOH

VOL

DVDD-0.5

-

0.5

0.4

V

Input Leakage Current Iin - - ±10 μA

SWITCHING CHARACTERISTICS

(Ta=−40 ∼ 85°C; AVDD=4.75 ∼ 5.25V; DVDD=3.0 ∼ 5.25V; CL=20pF)

Parameter Symbol min typ max Unit

Master Clock Timing

Frequency

Pulse Width Low

Pulse Width High

fCLK

tCLKL

tCLKH

8.192

0.4/fCLK

24.576

MHz

ns

LRCK Frequency

Normal Speed Mode

Double Speed Mode

fsn

fsd

32

48

96

kHz

Duty Cycle

Slave mode

Master mode

45

50 55

%

Audio Interface Timing

Slave mode

BICK Period

BICK Pulse Width Low

Pulse Width High

LRCK Edge to BICK “↑” (Note 16)

BICK “↑” to LRCK Edge (Note 16)

LRCK to SDTO (MSB) (Except I2S mode)

BICK “↓” to SDTO

tBCK

tBCKL

tBCKH

tLRB

tBLR

tLRS

tBSD

160

65

30

35

ns

Master mode

BICK Frequency

BICK Duty

BICK “↓” to LRCK

BICK “↓” to SDTO

fBCK

dBCK

tMBLR

tBSD

−20

64fs

50

20

35

Hz

%

ns

Note 17. BICK rising edge must not occur at the same time as LRCK edge.

[AK5365]

MS0164-E-02 2012/12

- 11 -

Parameter Symbol min typ max Unit

Control Interface Timing (3-wire Serial mode):

CCLK Period

CCLK Pulse Width Low

Pulse Width High

CDTI Setup Time

CDTI Hold Time

CSN “H” Time

CSN “↓” to CCLK “↑”

CCLK “↑” to CSN “↑”

tCCK

tCCKL

tCCKH

tCDS

tCDH

tCSW

tCSS

tCSH

200

80

40

150

50

ns

Control Interface Timing (I2C Bus mode):

SCL Clock Frequency

Bus Free Time Between Transmissions

Start Condition Hold Time (prior to first clock pulse)

Clock Low Time

Clock High Time

Setup Time for Repeated Start Condition

SDA Hold Time from SCL Falling (Note 17)

SDA Setup Time from SCL Rising

Rise Time of Both SDA and SCL Lines

Fall Time of Both SDA and SCL Lines

Setup Time for Stop Condition

Pulse Width of Spike Noise Suppressed by Input Filter

fSCL

tBUF

tHD:STA

tLOW

tHIGH

tSU:STA

tHD:DAT

tSU:DAT

tR

tF

tSU:STO

tSP

-

4.7

4.0

4.7

4.0

4.7

0

0.25

-

4.0

0

100

-

1.0

0.3

-

50

kHz

μs

ns

Reset Timing

PDN Pulse Width (Note 18)

PDN “↑” to SDTO valid (Note 19)

PWN “↑” to SDTO valid (Note 20)

tPD

tPDV

150

516

ns

1/fs

Note 17. Data must be held long enough to bridge the 300ns-transition time of SCL.

Note 18. The AK5365 can be reset by bringing the PDN pin = “L”.

Note 19. This cycle is the number of LRCK rising edges from the PDN pin = “H”.

Note 20. This cycle is the number of LRCK rising edges from the PWN bit = “1”.

[AK5365]

MS0164-E-02 2012/12

- 12 -

 Timing Diagram

1/fCLK

MCLK

tCLKH tCLKL

VIH

VIL

1/fs

LRCK VIH

VIL

tBCK

BICK

tBCKH tBCKL

VIH

VIL

Clock Timing

LRCK VIH

VIL

tBLR

BICK VIH

VIL

tLRS

SDTO 50%DVDD

tLRB

tBSD

Audio Interface Timing (Slave mode)

[AK5365]

MS0164-E-02 2012/12

- 13 -

LRCK

BICK 50%DVDD

SDTO 50%DVDD

tBSD

tMBLR dBCK

50%DVDD

Audio Interface Timing (Master mode)

CSN VIH

VIL

tCSS

CCLK

tCDS

VIH

VIL

CDTI VIH

tCCKHtCCKL

tCDH

VIL

C1 C0 R/W

WRITE Command Input Timing

CSN VIH

VIL

tCSH

CCLK VIH

VIL

CDTI VIH

tCSW

VIL

D1 D0D2

WRITE Data Input Timing

[AK5365]

MS0164-E-02 2012/12

- 14 -

StopStartStartStop

tHIGH

tHD:DAT

SDA

SCL

tBUF tLOW tR tF

tSU:DAT

VIH

VIL

tHD:STA tSU:STA

VIH

VIL

tSU:STO

tSP

I2C Bus Mode Timing

tPD

PDN VIL

CSN VIH

VIL

tPDV

SDTO 50%DVDD

PDN VIH

VIL

tPDV

SDTO 50%DVDD

Power Down & Reset Timing

[AK5365]

MS0164-E-02 2012/12

- 15 -

OPERATION OVERVIEW

 System Clock

MCLK (256fs/384fs/512fs), BICK (48fs∼) and LRCK (fs) clocks are required in slave mode. The LRCK clock input must

be synchronized with MCLK, however the phase is not critical. MCLK frequency is automatically detected in slave mode.

Table 1 shows the relationship of typical sampling frequency and the system clock frequency.

MCLK (256fs/384fs/512fs) is required in master m ode. MCLK frequency is selected by CKS1-0 bits as shown i n Table 2.

In master mode, after setting CKS1-0 bits, there is a possibility the frequen cy and duty of LRCK and BICK outputs

become an abnormal state.

All external clocks (M CLK, BICK and LRCK) m ust be present unless PDN pin = “L” and PWN bit = “1”. If these clocks

are not provided, the AK5365 may draw excess current due to its use of internal dynamically refreshed logic. If the

external clocks are not present, place the AK5365 in power-down mode (PDN pin = “L” or PWN bit = “0”). In master

mode, the master clock (MCLK) must be provided unless PDN pin = “L”.

MCLK

fs 256fs 384fs 512fs

32kHz 8.192MHz 12.288MHz 16.384MHz

44.1kHz 11.2896MHz 16.9344MHz 22.5792MHz

48kHz 12.288MHz 18.432MHz 24.576MHz

96kHz 24.576MHz N/A N/A

Table 1. System clock example (Slave mode)

MCLK

CKS1 CKS0

32kHz ≤ fs ≤ 48kHz 48kHz < fs ≤ 96kHz

0 0 256fs 256fs Default

0 1 512fs N/A

1 0 384fs N/A

1 1 N/A N/A

Table 2. Master clock frequency select (Master mode)

 Audio Interface Format

Two kinds of dat a formats can be chosen wi th t he DIF bi t (Tabl e 3) and t he C TR L pi n (Tabl e 4). The DIF bit and C T R L

pin are ORed between pin and register. In bot h modes, t he serial data i s in MSB fi rst, 2’s complim ent form at. The SDTO

is clocked out on the falling edge of BICK. The audio interface supports both master and slave modes. In master mode,

BICK and LRCK are output with the BICK frequency fixed to 64fs and the LRCK frequency fixed to 1fs.

Mode DIF bit SDTO LRCK BICK Figure

0 0 24bit, MSB justified H/L ≥ 48fs Figure 1

1 1 24bit, I2S Compatible L/H ≥ 48fs Figure 2

Default

Table 3. Audio Interface Format (CTRL pin = “L”)

Mode CTRL pin SDTO LRCK BICK Figure

0 L 24bit, MSB justified H/L ≥ 48fs Figure 1

1 H 24bit, I2S Compatible L/H ≥ 48fs Figure 2

Table 4. Audio Interface Format (DIF bit = “0”)

[AK5365]

MS0164-E-02 2012/12

- 16 -

LRCK

BICK(64fs)

SDTO(o)

0

23 22

12

4 0

20 21 24 31 0 12

23 22 0

10

23

2220 21 31

23:MSB, 0:LSB

Lch Data Rch Data

24

321

22 23 23

1234

Figure 1. Mode 0 Timing

LRCK

BICK(64fs)

SDTO(o)

0

23 22

12

4 0

2521 24 0 12

23 22 0

1022 2521 24

321

22 23 23

1234

3

23:MSB, 0:LSB

Lch Data Rch Data

Figure 2. Mode 1 Timing

 Master Mode and Slave Mode

The M/S pin selects either master or slave mode. M/S pin = “H” selects master mode and “L” selects slave mode. The

AK5365 outputs BICK and LRCK in master mode. In slave mode, MCLK, BICK and LRCK are input externally.

BICK, LRCK

Slave Mode BICK = Input

LRCK = Input

Master Mode BICK = Output

LRCK = Output

Table 5. Master mode/Slave mode

 Digital High Pass Filter

The ADC has a digital high pass filter for DC offset cancellation. The cut-off frequency of the HPF is 1.0Hz

(@fs=48kHz) and scales with sampling rate (fs).

[AK5365]

MS0164-E-02 2012/12

- 17 -

 Power-up/down

The AK5365 is placed in the power-down mode by bringing PDN pin = “L” and the digital filter is also reset at the sam e

time. This reset should always be done after power-up. An analog initialization cycle starts after exiting the power-down

mode. Therefore, the output data SDTO becomes available after 516 cycles of LRCK.

(1) Power-up Sequence 1

Power Supply (1)

PDN pin

ADC I nte rnal State

IPGA

SDTO

PDN INITA Normal

00H 00H → 7FH 7FH

“0” FI Output

External clocks

in s l ave mode The clocks can be stopped.

MCLK, LRCK, BI CK

External clocks

in master mode The clocks can be stopped.

MCLK

BICK, LRCK

in master mode BICK, LRCK

Fixed to “L”

- INITA : Initializing period of ADC analog section (516/fs).

- FI : Fade in. After exiting power down, IPGA value fades in.

- PDN : Power down state.

- The period of (1) should be min. 150ns in Figure 3.

Figure 3. Power-up Sequence 1

[AK5365]

MS0164-E-02 2012/12

- 18 -

(2) Power-up Sequence 2

Power Supply (1)

PDN pin

ADC I nte rnal State

IPGA

SDTO

PDN INITA Normal

00H 00H → 7FH 7FH

“0” FI Output

External clocks

in s l ave mode MCLK, LRCK , BICK

External clocks

in master mode MCLK

BICK, LRCK

in master mode Fixed to “L” BICK, LRCK

Unsettling

The clocks can be input.

The clocks can be i nput.

MCLK

MCLK, BICK, LRCK

- INITA : Initializing period of ADC analog section (516/fs).

- FI : Fade in. After exiting power down, IPGA value fades in.

- PDN : Power down state.

- The period of (1) should be min. 150ns in Figure 4.

Figure 4. Power-up Sequence 2

[AK5365]

MS0164-E-02 2012/12

- 19 -

 Input Selector

The AK5365 includes 5ch stereo input selectors (Figure 5). The input selector is 5 to 1 selector. The input channel is set

by the SEL2-0 bits (Table 6) and the SEL2-0 pins (Table 7). The SEL2-0 pins should be fixed to “LLL” if the AK5365 is

controlled by the SEL 2-0 bits, because the setting of the SEL2-0 pins are prior to the SEL2-0 bits setting.

SEL2 bit SEL1 bit SEL0 bit Input Channel

0 0 0 LIN1 / RIN1 Default

0 0 1 LIN2 / RIN2

0 1 0 LIN3 / RIN3

0 1 1 LIN4 / RIN4

1 0 0 LIN5 / RIN5

Table 6. Input Selector (SEL2-0 pin = “LLL”)

SEL2 pin SEL1 pin SEL0 pin Input Channel

L L L LIN1 / RIN1

L L H LIN2 / RIN2

L H L LIN3 / RIN3

L H H LIN4 / RIN4

H L L LIN5 / RIN5

Table 7. Input Selector (SEL2-0 bit = “000”)

LIN1

LIN2

LIN3

LIN4

LIN5

RIN1

RIN2

RIN3

RIN4

RIN5

Pre-Amp

Figure 5. Input Selector

[AK5365]

MS0164-E-02 2012/12

- 20 -

[Input selector switching sequence]

The input selector should be changed after soft mute to avoid the switching noise of the input selector (Figure 6).

1. Enable the soft mute before changing channel.

2. Change channel.

3. Disable the soft mute.

SMUTE

A

ttenuation

Channel

D AT T Level

-∞

(1)

(2)

LIN1/RIN1 LIN2/RIN2

(1)

Figure 6. Input channel switching sequence example

The period of (1) varies in the setting value of DATT. It takes 1024/fs to mute when DATT value is 0dB.

When changing channels, the input channel should be changed during (2). The period of (2) should be around 200ms

because there is some DC difference between the channels.

 Function of CTRL Pin

The CTRL pin sets the audio interface format and the type of serial control interface. When the CTRL pin is “L”, the

audio interface format is selected by the DIF bit and the serial control interface is 3-wire control mode. When the CTRL

pin is “H”, the audio interface format is fixed to 24bit I2S compatible and the serial control interface is I2C-bus control

mode.

CTRL pin Audio Interface Format Serial Control Interface

L Note 3-wire Control

H 24bit, I2S Compatible I2C-Bus Control

Table 8. CTRL pin Function

Note: The audio interface format is ORed between the CTRL pin and DIF bit. When the CTRL pin is “L”, the audio

interface format can be selected between 24bit MSB justified and 24bit I2S compatible by DIF bit. When the CTRL

pin is “H”, the audio interface format is fixed to 24bit I2S compatible.

[AK5365]

MS0164-E-02 2012/12

- 21 -

 Input Attenuator

The input ATTs are constructed by adding the input resistor (Ri) for LIN1-5/RIN1-5 pins and the feedback resistor (Rf)

between LOPIN (ROPIN) pin and LOUT (ROUT) pin (Figure 7). The input voltage range of the IPGAL/IPGAR pin is

typically 0.2 x AVDD (Vrms). If the input voltage of the input selector exceeds 0.2 x AVDD, the input voltage of the

IPGAL/IPGAR pins must be attenuated to 0.2 x AVDD by the input ATTs. Table 9 shows the example of Ri and Rf.

LIN1

LIN2

LIN3

LIN4

LIN5

RIN1

RIN2

RIN3

RIN4

RIN5

IPGAL

ROPIN ROUT IPGAR

LOPIN LOUT

Pre-Amp

To IPGA

Ri

Rf

Figure 7. Input ATT

• Example for input range

Input Range Ri [kΩ] Rf [kΩ] ATT Gain [dB] IPGAL/R pin

4Vrms 47 12 −11.86 1.02Vrms

2Vrms 47 24 −5.84 1.02Vrms

1Vrms 47 47 0 1Vrms

Table 9. Input ATT example

[AK5365]

MS0164-E-02 2012/12

- 22 -

 Input Volume

The AK5365 includes two independent channel anal og vol umes (IPGA) with 25 levels at 0.5dB steps located in front of

the ADC. The digital volume controls (DATT) have 128 l evels (including MUTE) and i s located after the ADC. Both the

analog and digital volumes are controlled through the same register address. When the MSB of the register is “1”, the

IPGA changes and when the MSB = “0”, the DATT changes.

The IPGA is a true analog volume control that improves the S/N ratio as seen in Table 10. Independent zero-crossing

detection is used to ensure level chang es only occur during zero -crossings. If there are no zero-crossin gs, the level will

then change after a time-out period (Table 11 ); the time-out period scales with fs. If a new v alue is written to the IPGA

register before the IPGA changes at the zero crossing or time-out, t he previous value becomes i nvalid. The timer (channel

independent) for time-out is reset and the timer restarts for new IPGA value.

The DATT is a pseudo-log volume that is linear-interpolated internally. When changing the level, the transition between

ATT values has 8031 levels and is done by soft changes, eliminating any switching noise.

Input Gain Setting

0dB +6dB +12dB

fs=48kHz, A-weight 103dB 100dB 96dB

Table 10. PGA+ADC S/N

ZTM1 ZTM0 Zero crossing timeout period @fs=48kHz

0 0 288/fs 6ms

0 1 1152/fs 24ms

1 0 2304/fs 48ms Default

1 1 4608/fs 96ms

Table 11. Zero crossing timeout period

[Writing operation at ALC Enable]

Writing to the area over 80H (Table 17) of IPGL/R regi sters is i gnored during ALC operat ion. Afte r ALC is disabled,

the IPGA changes to the last written data by zero-crossing or time-out. In case of writing to the DATT area under 7FH

(Table 17) of IPGL/R registers, the DATT changes even if ALC is enabled.

[AK5365]

MS0164-E-02 2012/12

- 23 -

 ALC Operation

[1] ALC Limiter Operation

When the ALC limiter is enabled, and either Lch or Rch exceed the ALC limiter detection level (LMTH bit), the IPGA

value is attenuated by t he amount defined in the ALC limiter ATT step (LMAT bit) automat i cal l y . Then the IPGA value

is changed commonly for L/R channels.

When the ZELMN bit = “1”, the timeout period is set by the LTM1-0 bits. The operation for attenuation is done

continuously until the input signal level becomes the ALC limiter detection level (LMTH bit) or less. If the ALC bit does

not change into “0” or the ALC pin does not change into “L” after completing the attenuation, the attenuation operation

repeats until the input signal level equals or exceeds the ALC limiter detection level (LMTH bit).

When the ZELMN bit = “0”, the timeout period is set by the ZTM1-0 bits. This enables the zero-crossing attenuation

function so that the IPGA value is attenuated at the zero-detect points of the waveform.

When FR bit = “1”, the ALC operation corresponds to the impulse noise in additional to the normal ALC operation. Then

if the impulse noise is supplied at ZELMN bit = “0”, the ALC operation becomes the faster period than a set of ZTM1-0

bits. In case of ZELMN bit = “1”, it becomes the same period as LTM1-0 bits. When FR bit = “0”, the ALC operation is

the normal ALC operation.

[2] ALC Recovery Operation

The ALC recovery refers to the amount of time that the AK5365 will allow a signal to exceed a predetermined limiting

value prior to enabling t he limiting functi on. The ALC recovery operation uses the WTM1-0 bits to define the wai t period

used after completing an ALC limiter operation. If the input signal does not exceed the “ALC Recovery Waiting Counter

Reset Level”, the ALC recovery operation starts. The IPGA value increases automatically during this operation up to the

reference level (REF7-0 bits). The ALC recovery operation is done at a period set by the WTM1-0 bits. Zero crossing is

detected during WTM1-0, the ALC recovery operation waits WTM1-0 period and the next recovery operation starts.

During the ALC recovery operation, when input signal level exceeds the ALC limiter detection level (LMTH bit), the

ALC recovery operation changes immediately into an ALC limiter operation.

In the case of “(Recovery waiti ng counter reset level ) ≤ Input Signal < Lim i ter detect ion l evel” duri ng the ALC recovery

operation, the wait timer for the ALC recovery operation is reset. Therefore, in the case of “(Recovery waiting counter

reset level) > Input Signal”, the wait timer for the ALC recovery operation starts.

When the impulse noise is input at FR bit = “1”, the ALC recovery operation becomes faster than a normal recovery

operation. When the FR bit = “0”, the ALC recovery operation is done by normal period.

[AK5365]

MS0164-E-02 2012/12

- 24 -

[3] ALC Level Diagram

(1) ALC=OFF

Figure 8 and 9 show the level diagram example at ALC=OFF. In Figure 8, Input ATT is −12dB.

Input

4Vrms

2Vrms

ATT IPGA ADC

0dBFS

-12dB

1Vrms

-12dB

+6dB

+12dB

Figure 8. ALC Level diagram example (ALC=OFF)

In Figure 9, Input ATT is −6dB.

Input

2Vrms

1Vrms

ATT IPGA ADC

0dBFS

-6dB

0.5Vrms

-6dB

+6dB

+12dB

Figure 9. ALC Level diagram example (ALC=OFF)

[AK5365]

MS0164-E-02 2012/12

- 25 -

(2) ALC=ON

Figure 10 and 11 show the level diagram example at ALC=ON. In Figure 10, Input ATT is −12dB and REF7-0 bits are

“8CH”.

Input

4Vrms

2Vrms

ATT ALC ADC

-12dB

1Vrms

-12dB

0.5Vrms

-0.5dB -0.5dBFS

-6dBFS

-12dBFS

0dBFS

+5.5dB

+6dB

0.25Vrms

Figure 10. ALC Level diagram example (ALC=ON)

In Figure 11, Input ATT is −6dB and REF7-0 bits are “8CH”.

Input

2Vrms

1Vrms

ATT ALC ADC

-6dB

0.5Vrms

-6dB

0.25Vrms

-6dB

-0.5dB -0.5dBFS

-6dBFS

0dBFS

+5.5dB

+6dB

-12dBFS

Figure 11. ALC Level diagram example (ALC=ON)

[AK5365]

MS0164-E-02 2012/12

- 26 -

[4] Example of ALC Operation

The following registers should not be changed during the ALC operation.

• LTM1-0, LMTH, LMAT, WTM1-0, ZTM1-0, RATT, REF7-0, ZELMN bits

• The IPGA value of Lch becomes the start value if the IPGA value is different with Lch and Rch when the ALC starts.

• Writing to the area over 80H (Table 17) of IPGL/R regi sters is ignored during ALC operat ion. After ALC is disabled,

the IPGA changes to the last written data by zero-crossing or time-out. In case of writing to the DATT area under

7FH

(Table 17) of IPGL/R registers, the DATT changes even if ALC is enabled.

Manual Mode

Finish ALC mode and return to manual mode

Finish ALC mo de?

Yes

No

Set (SEL 2- 0 bits or SEL2-0 pins)

WR (ZTM1-0, WTM1-0, L TM 1-0)

WR (LMAT, RATT, LMTH)

WR (REF7-0)

WR (IPGA7 -0)

ALC Operat ion

WR (ALC = “0”)

WR (ALC = “1”)

(1)

(2)

(1)

(2)

Note : WR : Write

Figure 12. Registers set-up sequence at ALC operation

(1): Enable soft mute (2): Disable soft mute

Note : ALC operation is enabled by the ALC pin.

Note : All the bi ts about ALC operati on operate by the default value when an ALC operat ion is starte d with the ALC pin

without setting up a bit about ALC operation with the register. A bit about ALC operation operate by the setting

value when a bit about ALC operation is set up wi th the register and an ALC operation is started wit h the ALC pin.

Note : After ALC operation is disabled, the IPGA ch anges to the last written data during or before ALC operation.

[AK5365]

MS0164-E-02 2012/12

- 27 -

[5] IPGA value before and after ALC operation

[Operation Example 1]

1. Set IPGA = +12dB at ALC=OFF. DATT portion is set to 0dB internally.

2. ALC=ON after soft mute is enabled.

3. Disable the soft mute.

4. During ALC operation. The IPGA changes from −9.5dB to the value set by REF7-0 bits.

5. ALC=OFF after soft mute is enabled.

6. Disable the soft mute. The IPGA return to +12dB automatically.

[Operation Example 2]

1. Set IPGA = +12dB at ALC=OFF. DATT portion is set to 0dB internally.

2. ALC=ON after soft mute is enabled.

3. Disable the soft mute.

4. During ALC operation. When the DATT porti on is set to −10dB, the IPGA changes from −19.5dB to the value set

by REF7-0 bits.

5. ALC=OFF after soft mute is enabled.

6. Disable the soft mute. The IPGA setting is −10dB.

 Soft Mute Operation

Soft mute operation is performed in the digital domain of the ADC output.

Soft mut e can be controlled by SMUTE bit or SMUTE pin. The SMUTE bi t and SM UTE pi n are ORed bet ween pi n and

register. When SMUTE bit goes “1” or SMUTE pin goes “H”, the ADC output data is attenuated by −∞ within 1024

LRCK cycles. When the SMUTE bit returned “0” or SMUTE pin goes “L” the mute is cancelled and the output

attenuation gradually changes to IPGA value within 1024 LRCK cycles. If the soft mute is cancelled before mute state

after starting of the operation, the attenuation is discontinued and returned to IPGA value.

Soft mute function and digital volume are common.

SMUTE

A

ttenuation

DATT Level

-∞GD GD

(1)

(2)

(3)

SDTO

Figure 13. Soft Mute Function

(1) The output signal is attenuated by −∞ within 1024 LRCK cycles (1024/fs).

(2) Digital output delay from the analog input is called the group delay (GD).

(3) If the soft mute is cancelled before the mute, the attenuation is disco ntinued and returned to IPGA v alue.

[AK5365]

MS0164-E-02 2012/12

- 28 -

 Chip Address

In case of 3-wire control m ode, the chip address is fixed to C1 bit = “1” and C 0 bit = “0”. Table 12 shows the relati onship

between chip address (C1-0 bits) and CAD1 pin in I2C-bus control mode.

CAD1 pin C1 bit C0 bit

L 0 Fixed to “1”

H 1 Fixed to “1”

Table 12. Chip address in I2C-bus control

Note : C1 bit should match with the input level of CAD1 pin.

 Serial Control Interface

(1) 3-wire Serial Control Mode (CTRL pin = “L”)

Internal registers ma y be written by using the 3-wire µP interface pins (CSN, CCLK and CDTI). The data on this interface

consists of a Chip address (2bits, Fi xed to “10”), Read/Write (1bit, Fixed to “1”, Write only), Regi ster address (MSB first,

5bits) and Control dat a (MSB first, 8bi ts). Address and data i s clocked in on the risi ng edge of CCLK and data is clocked

out on the falling edge. After a low-to-high transition of CSN, data is latched for write operations. The clock speed of

CCLK is 5MHz (max). The value of internal registers is initialized at PDN pin = “L”.

CSN

CCLK

CDTI

0123456789101112131415

C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0

C1 - C0 : Chip Address (C1="1", C0="0")

R/W : READ / WRITE (Fixed to "1" : WRITE only)

A4 - A0 : Register Address

D7 - D0 : Control Data

Figure 14. Serial Control I/F Timing

[AK5365]

MS0164-E-02 2012/12

- 29 -

(2) I2C-bus Control Mode (CTRL pin = “H”)

The AK5365 supports the standard-mode I2C-bus (max: 100kHz). The AK5365 does not support a fast-mode I2C-bus

system (max: 400kHz).

(2)-1. WRITE Operations

Figure 15 shows the data transfer sequence for the I2C-bus mode. All comm a nds are preceded by a START condition. A

HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 21). After the

START condition, a slave address is sent. Thi s address is 7 bits long followed by an eighth bit that is a data direction bit

(R/W). The most significant five bits of the slave address are fixed as “00100”. The next one bit are CAD1 (device

address bits). This one bit identify the specific device on the bus. The hard-wired input pin (CAD1 pin) set these device

address bits (Figure 16). If the slave address m atches that of the AK5365, the AK5365 generates an acknowledge and the

operation is executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH)

during the acknowledge clock pulse (Figure 22). A R/W bit value of “1” indicates that the read operation is to be

executed. A “0” indicates that the write operation is to be executed.

The second byte consists of the control register address of the AK5365. The format is MSB first, and those most

significant 3-bits are fixed to zeros (Figure 17). The data after the second byte contains control data. The format is MSB

first, 8bits (Figure 18). The AK5365 generates an acknowledge after each byte has been received. A data transfer is

always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL

is HIGH defines a STOP condition (Figure 21).

The AK5365 can perform more than one byte write operation per sequence. After receipt of the third byte the AK5365

generates an acknowledge and awaits t he next data. The master can transmit m ore than one byte instead of term inating the

write cycle after the first data byte is transferred. After receiving each data packet the internal 5-bit address counter is

incremented by one, and the next data is automatically taken into the next address. If the address exceeds 07H prior to

generating the stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten.

The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state of the data

line can only change when the clock signal on the SCL line is LOW (Figure 23) except for the START and STOP

conditions.

SDA Slave

Address

S

T

A

R

T

R/W="0"

A

C

K

Sub

Address(n) A

C

K

Data(n)

A

C

K

Data(n+1)

A

C

K

A

C

K

Data(n+x)

A

C

K

P

S

T

O

P

Figure 15. Data Transfer Sequence at the I2C-Bus Mode

0 0 1 0 0 CAD1 1 R/W

(CAD1 should match with CAD1 pin.)

Figure 16. The First Byte

0 0 0 A4 A3 A2 A1 A0

Figure 17. The Second Byte

D7 D6 D5 D4 D3 D2 D1 D0

Figure 18. Byte Structure after the second byte

[AK5365]

MS0164-E-02 2012/12

- 30 -

(2)-2. READ Operations

Set the R/W bit = “1” for the READ operation of the AK5365. After transmission of data, the master can read the next

address’s data by generating an acknowledge instead of term inating the write cycle after the receipt of the first data word.

After receiving each data packet the internal 5-bit address counter is incremented by one, and the next data is

automatically taken into the next address. If the address exceeds 07H prior to generating a stop condition, the address

counter will “roll over” to 00H and the previous data will be overwritten.

The AK5365 supports two basic read operations: CURRENT ADDRESS READ and RANDOM ADDRESS READ.

(2)-2-1. CURRENT ADDRESS READ

The AK5365 contains an internal address counter that maintains the address of the last word accessed, incremented by

one. Therefore, if the last access (either a read or write) were to address n, the next CURRENT READ operation would

access data from the address n+1. After receipt of the slave address with R/W bit set to “1”, the AK5365 generates an

acknowledge, transmits 1-byte of data to the address set by the internal address counter and increments the internal

address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition,

the AK5365 ceases transmission.

SDA Slave

Address

S

T

A

R

T

R/W="1"

A

C

K

A

C

K

Data(n+1)

A

C

K

Data(n+2)

A

C

K

A

C

K

Data(n+x)

A

C

K

P

S

T

O

P

Data(n)

Figure 19. CURRENT ADDRESS READ

(2)-2-2. RANDOM ADDRESS READ

The random read operation allows the ma ster to access any memory location at random. Prior to issuing the slave address

with the R/W bit set to “1”, the master must first perform a “dum m y ” write operation. The m aster issues a start request, a

slave address (R/W bit = “0”) and then the register address to read. After the register address is acknowledged, t he master

immediately reissues the start request and the slave address with the R/W bit set to “1”. The AK5365 then generates an

acknowledge, 1 byte of data and increments the internal address counter by 1. If the master does not generate an

acknowledge to the data but instead generates a stop condition, the AK5365 ceases transmission.

SDA Slave

Address

S

T

A

R

T

R/W="0"

A

C

K

A

C

K

A

C

K

Data(n)

A

C

K

Data(n+x)

A

C

K

P

S

T

O

P

Sub

Address(n) SSlave

Address

R/W="1"

S

T

A

R

T

Data(n+1)

A

C

K

A

C

K

Figure 20. RANDOM ADDRESS READ

[AK5365]

MS0164-E-02 2012/12

- 31 -

SCL

SDA

stop conditionstart condition

SP

Figure 21. START and STOP Conditions

SCL FROM

MASTER

acknowledge

DATA

OUTPUT BY

TRANSMITTER

DATA

OUTPUT BY

RECEIVER

1 98

START

CONDITION

not acknowledge

clock pulse for

acknowledgement

S

2

Figure 22. Acknowledge on the I2C-Bus

SCL

SDA

data line

stable;

data valid

change

of data

allowed

Figure 23. Bit Transfer on the I2C-Bus

[AK5365]

MS0164-E-02 2012/12

- 32 -

 Control by Pin and Bit

Function Pin bit

ALC ALC Enable Pin (Internal Pull-down)

“L” : Disable

“H” : Enable

ALC Enable bit

“0” : Disable

“1” : Enable

Input Selector

SEL2-0 Pin

“LLL” : LIN1/RIN1

“LLH” : LIN2/RIN2

“LHL” : LIN3/RIN3

“LHH” : LIN4/RIN4

“HLL” : LIN5/RIN5

SEL2-0 bit

“000” : LIN1/RIN1

“001” : LIN2/RIN2

“010” : LIN3/RIN3

“011” : LIN4/RIN4

“100” : LIN5/RIN5

Soft Mute SMUTE Pin (Internal Pull-down)

“L” : Normal operation

“H” : Soft muted

SMUTE bit

“0” : Normal operation

“1” : Soft muted

Audio Interface Format CTRL Pin

“L” : 24bit MSB justified

“H” : 24bit I2S Compatible

DIF bit

“0” : 24bit MSB justified

“1” : 24bit I2S Compatible

Table 13. Pin and Bit control

Note : The SEL2-0 pins should be fixed to “LLL” if the AK5365 is controlled by the SEL2-0 bits, because the setting of

the

SEL2-0 pins are prior to the SEL2-0 bits setting. Other Functions are ORed between pin and register.

 Register Map

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

00H Power Down & Reset Control 0 0 0 0 0 0 0 PWN

01H Input Selector Control 0 0 0 0 0 SEL2 SEL1 SEL0

02H Clock & Format Control 0 0 0 0 DIF CKS1 CKS0 SMUTE

03H Timer Select 0 0 LTM1 LTM0 ZTM1 ZTM0 WTM1 WTM0

04H Lch IPGA Control IPGL7 IPGL6 IPGL5 IPGL4 IPGL3 IPGL2 IPGL1 IPGL0

05H Rch IPGA Control IPGR7 IPGR6 IPGR5 IPGR4 IPGR3 IPGR2 IPGR1 IPGR0

06H ALC Mode Control 1 0 0 ZELMN ALC FR LMTH RATT LMAT

07H ALC Mode Control 2 REF7 REF6 REF5 REF4 REF3 REF2 REF1 REF0

PDN pin = “L” resets the registers to their default valu es.

Note: Unused bits must contain a “0” value.

Note: Only write to address 00H to 07H.

[AK5365]

MS0164-E-02 2012/12

- 33 -

 Register Definitions

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

00H Power Down & Reset Control 0 0 0 0 0 0 0 PWN

Default 0 0 0 0 0 0 0 1

PWN: Power down control

0 : Power down. All registers are not initialized.

1 : Normal Operation (Default)

“0” powers down all sections and then both IPGA and ADC do not operate. The contents of all register

are not initialized and en abled to write to the registers.

When MCLK and LRCK are changed, it is not necessary to reset by the PDN pin or PWN bit because the

AK5365 builds in reset-free circuit. However, it can be reduced the noise by reset.

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

01H Input Selector Control 0 0 0 0 0 SEL2 SEL1 SEL0

Default 0 0 0 0 0 0 0 0

SEL2-0: Input selector (see Table 6)

Initial values are “000”.

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

02H Clock & Format Control 0 0 0 0 DIF CKS1 CKS0 SMUTE

Default 0 0 0 0 0 0 0 0

SMUTE: Soft Mute control

0 : Normal Operation (Default)

1 : SDTO outputs soft-muted.

CKS1-0: Master clock frequency select (see Table 2)

Initial values are “00”.

DIF: Audio interface format (see Table 3)

Initial values are “0”.

When CTRL pin is “H”, audio interface format is fixed to I2S compatible.

[AK5365]

MS0164-E-02 2012/12

- 34 -

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

03H Timer Select 0 0 LTM1 LTM0 ZTM1 ZTM0 WTM1 WTM0

Default 0 0 1 0 1 0 1 1

WTM1-0: ALC Recovery waiting time (see Table 14)

A period of recovery operation when any limiter operation does not occur during the ALC operation.

WTM1 WTM0 ALC recovery operation waiting period @fs=48kHz

0 0 288/fs 6ms

0 1 1152/fs 24ms

1 0 2304/fs 48ms

1 1 4608/fs 96ms Default

Table 14. ALC recovery waiting time

ZTM1-0: Zero crossing timeout (see Table 15)

When the IPGA of each L/R channels perform zero crossing or timeout independently, the IPGA value is

changed by the μP WRITE operation, ALC recovery operation or ALC limiter operation (ZELMN bit = “0”).

ZTM1 ZTM0 Zero crossing timeout period @fs=48kHz

0 0 288/fs 6ms

0 1 1152/fs 24ms

1 0 2304/fs 48ms Default

1 1 4608/fs 96ms

Table 15. Zero crossing timeout

LTM1-0: ALC Limiter period (see Table 16)

When ZELMN bit = “1”, the IPGA value is changed immediately. When the IPGA value is changed

continuously, the change is done by the period set by the LTM1-0 bits.

LTM1 LTM0 ALC limiter operation period @fs=48kHz

0 0 3/fs 63μs

0 1 6/fs 125μs

1 0 12/fs 250μs Default

1 1 24/fs 500μs

Table 16. ALC limiter period

[AK5365]

MS0164-E-02 2012/12

- 35 -

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

04H Lch IPGA Control IPGL7 IPGL6 IPGL5 IPGL4 IPGL3 IPGL2 IPGL1 IPGL0

05H Rch IPGA Control IPGR7 IPGR6 IPGR5 IPGR4 IPGR3 IPGR2 IPGR1 IPGR0

Default 0 1 1 1 1 1 1 1

IPGL/R7-0: Input PGA & Digital volume control (see Table 17)

Initial values are “7FH”.

Digital ATT with 128 levels operates when writing data of less than 7FH. This ATT is a linear ATT with 8032

levels internally and these levels are assigned to pseudo-log data with 128 levels. The transition between ATT

values has 8032 levels and is done by soft changes. For example, when ATT changes from 7FH to 7EH, the

internal ATT value decreases from 8031 to 7775, one by one every fs cycle. It takes 8031 cycles

(167ms@fs=48kHz) from 7FH to 00H (Mute).

The IPGAs are set to “00H” when PDN pin goes “L”. After returning to “H”, the IPGAs fade into the initial

value, “7FH” in 8031 cycles.

The IPGAs are set to “00H” when PWN bit goes “0”. After returning to “1”, the IPGAs fade into the current

value. The ADC output is “0” during the first 516LRCK cycles.

Writing to the area over 80H (Table 17) of IPGL/R registers is ignored during ALC operation. After ALC is

disabled, the IPGA changes to the last written data by zero-crossing or time-out. In case of writing to the DATT

area under 7FH (Table 17) of IPGL/R registers, the DATT changes even if ALC is enabled.

[AK5365]

MS0164-E-02 2012/12

- 36 -

Data (hex) Internal

(DATT) Gain (dB) Step width (dB)

98H - +12 -

97H - +11.5 0.5

96H - +11 0.5

: - : 0.5

82H - +1.0 0.5

81H - +0.5 0.5

80H - 0 -

IPGA

Analog volume with 0.5dB step

7FH 8031 0 -

7EH 7775 −0.28 0.28

7DH 7519 −0.57 0.29

: : : :

70H 4191 −5.65 0.51

6FH 3999 −6.06 0.41

6EH 3871 −6.34 0.28

: : : :

60H 2079 −11.74 0.52

5FH 1983 −12.15 0.41

5EH 1919 −12.43 0.28

: : : :

50H 1023 −17.90 0.53

4FH 975 −18.32 0.42

4EH 943 −18.61 0.29

: : : :

40H 495 −24.20 0.54

3FH 471 −24.64 0.43

3EH 455 −24.94 0.30

: : : :

30H 231 −30.82 0.58

2FH 219 −31.29 0.46

2EH 211 −31.61 0.32

: : : :

20H 99 −38.18 0.67

1FH 93 −38.73 0.54

1EH 89 −39.11 0.38

: : : :

10H 33 −47.73 0.99

0FH 30 −48.55 0.83

0EH 28 −49.15 0.60

: : : :

05H 10 −58.10 1.58

04H 8 −60.03 1.94

03H 6 −62.53 2.50

02H 4 −66.05 3.52

01H 2 −72.07 6.02

00H 0 MUTE

DATT

External 128 levels are converted to internal

8032 linear levels of DATT. Internal DATT

soft-changes between data.

DATT =2^m x (2 x l + 33) – 33

m: MSB 3-bits of data

l: LSB 4-bits of data

Table 17. IPGA Code Table

[AK5365]

MS0164-E-02 2012/12

- 37 -

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

06H ALC Mode Control 1 0 0 ZELMN ALC FR LMTH RATT LMAT

Default 0 0 1 0 1 0 0 0

LMAT: ALC Limiter ATT step (see Table 18)

During the ALC limiter operation, when either Lch or Rch exceeds the ALC limiter detection level set by LMTH

bit, the number of st eps attenuated from the current IPGA value is set. For exam ple, when the current IPGA value

is 94H and the LMAT bit = “1”, the IPGA transition to 92H when the ALC limiter operation starts, resulting in

the input signal level being attenuated by 1dB (=0.5dB x 2).

LMAT ATT Step

0 1 Default

1 2

Table 18. ALC limiter ATT step

RATT: ALC Recovery gain step (see Table 19)

During the ALC recovery operation, the number of steps changed from the current IPGA value is set. For

example, when the current IPGA value is 82H and RATT bit = “1” is set, the IPGA changes to 84H by the ALC

recovery operation and the output signal level is gained up by 1dB (=0.5dB x 2). When the IPGA value exceeds

the reference level (REF7-0 bits), the IPGA value does not increase.

RATT Gain Step

0 1 Default

1 2

Table 19. ALC recovery gain step

LMTH: ALC Limiter detection level / Recovery waiting counter reset level (see Table 20)

The ALC limiter detection level and the ALC recovery counter reset level may be offset by about ±2dB.

LMTH ALC Limiter Detection Level ALC Recovery Waiting Counter Reset Level

0 ALC Output ≥ −0.5dBFS −0.5dBFS > ALC Output ≥ −2.5dBFS Default

1 ALC Output ≥ −2.0dBFS −2.0dBFS > ALC Output ≥ −4.0dBFS

Table 20. ALC Limiter detection level / Recovery waiting counter reset level

FR: ALC fast recovery

0 : Disable

1 : Enable (Default)

When the impulse noise is input, the ALC recovery operation becomes faster than a normal recovery operation.

ALC: ALC enable flag

0 : ALC Disable (Default)

1 : ALC Enable

ZELMN: Zero crossing enable flag at ALC limiter operation

0 : Enable

1 : Disable (Default)

When the ZELMN bit = “0”, the IPGA of each L/R channel perform a zero crossing or timeout independently.

The zero crossing timeout is the same as the ALC recovery operation. When the ZELMN bit = “1”, the IPGA

value is changed imme diately. The ALC Limiter period can be set up by a ZTM 1-0 bits when ZELMN bit = “0”,

it can be set up by a LTM1-0 bits when ZELMN bit = “1”

[AK5365]

MS0164-E-02 2012/12

- 38 -

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

07H ALC Mode Control 2 REF7 REF6 REF5 REF4 REF3 REF2 REF1 REF0

Default 1 0 0 0 1 0 0 1

REF7-0: Reference value at ALC recovery operation (see Table 21)

During the ALC recovery operation, if the IPGA value exceeds the setting reference value by gain operation,

then the IPGA does not become larger than the reference value.

The REF7-0 bits should not be set up except for Table 21.

DATA (hex) Gain (dB)

98H +12.0

97H +11.5

96H +11.0

95H +10.5

: :

89H +4.5 Default

: :

81H +0.5

80H 0

Table 21. Reference value at ALC recovery operation

[AK5365]

MS0164-E-02 2012/12

- 39 -

SYSTEM DESIGN

Figure 24 shows the system connection diagram. An evaluation board is available which demonstrates application

circuits, the optimum layout, power supply arrangements and measurement results.

• Master Mode, 3-wire control (CTRL pin = “L”)

LIN51

2

3

4

5

6

7

8

9

10

11

TEST1

LIN4

TEST2

LIN3

TEST3

LIN2

TEST4

LIN1

LOPIN

LOUT

Top View

AVDD

RIN5

44 43 42

TEST8

RIN4

41 40 38 3739 35 3436

TEST7

RIN3

TEST6

RIN2

TEST5

RIN1

M/S

CTRL

47k

1μ

47k

1μ

47k

1μ

47k

1μ

47k

1μ

24k

4.7μ

47k

1μ

47k

1μ

47k

1μ

47k

1μ

47k

1μ

Reset

DSP and uP

33

32

31

30

29

28

27

26

25

24

23

CSN/CAD1

CCLK/SCL

CDTI/SDA

SEL2

SEL1

SEL0

SMUTE

ALC

PDN

MCLK

LRCK

Analog Supply

4.75 ~ 5.25V

IPGAR

12

ROUT

13

ROPIN

14 15 16

AVSS

17

VCOM

18

DVSS

19

DVDD

20 21

SDTO

22

BICK

0.1μ

10μ2.2μ

0.1μ

24k

4.7μ

10μ

0.1μ

Digital Supply

3.0 ~ 5.25V

IPGAL

Note:

- AVSS and DVSS of the AK5365 should be distributed separately from the ground of external digital devices

(MPU, DSP etc.).

- When LOUT/ROUT drives a capacitive load, resistors should be added in series between LOUT/ROUT

and capacitive load.

- All input pins except pull-down pin (ALC, SMUTE pins) should not be left floating.

Figure 24. Typical Connection Diagram

[AK5365]

MS0164-E-02 2012/12

- 40 -

1. Grounding and Power Supply Decoupling

The AK5365 requires careful attention to power supply and grounding arrangements. AVDD and DVDD are usually

supplied from the analog supply in the sy st em. Alternatively i f AVDD and DVDD are suppl i ed separat e l y , t he power up

sequence is not critical. AVSS and DVSS of the AK5365 must be connected to analog ground plane. System analog

ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit

board. Decoupling capacitors should be as near to t he AK5365 as possible, with the small value ceramic capacitor being

the closest.

2. Voltage Reference Inputs

The differential volt age between AVDD and AVSS sets the analog input range. VCOM is a signal ground of this chip. An

electrolytic capacitor 2.2µF parallel with a 0.1µF ceramic capacitor attached to VCOM pin eliminates the effects of high

frequency noise. No load current m ay be drawn from the VCOM pin. All si gnals, especi ally clocks, should be kept away

from the VREF and VCOM pins in order to avoid unwanted coupling into the AK5365.

3. Analog Inputs

An analog input of AK5365 is single-ended input to Pre-Am p through the exte rnal resistor. For input si gnal range, adjust

feedback resistor so that Pre-Am p output may become the input range (typ. 0.2 x AVDD Vrms) of IPGA (IPGAL, IPGAR

pin). Between the Pre-Amp output (LOUT, ROUT pin) and the IPGA input (IPGAL, IPGAR pin) is AC coupled with

capacitor. When the impedance of IPGAL/R pins is “R” and the capacitor of between the Pre-Amp output and the IPGA

input is “C”, the cut-off frequency is fc = 1/(2πRC).

The ADC output data format 2’s compliment. The internal HPF removes the DC offset.

The AK5365 samples the analog inputs at 64fs. The digital filter rejects noise above the stop band except for m ultiples of

64fs. The AK5365 includes an anti-aliasing filter (RC filter) to attenuate a noise around 64fs.

4. Attention to the PCB Wiring

LIN1-5 and RIN1-5 pins are the summ ing nodes of t he Pre-Amp. At tenti on should be given t o avoid coupling wit h other

signals on those nodes. This can be accomplished by making the wire lengt h of the input resistors as short as possible. The

same theory also applies to the LOPIN/ROPIN pins and feedback resistors; keep the wire length to a minimum. Unused

input pins among LIN1-5 and RIN1-5 pins should be left open.

When external devices are connected to LOUT and ROUT pin, the input impedance of an external device which the

LOUT and ROUT pins can drive is min 6.3kΩ.

[AK5365]

MS0164-E-02 2012/12

- 41 -

PACKAGE

0.15

0.09 ~ 0.20

0.37±0.10

10.0

1.70max

1 11

23

33

44pin LQFP (Unit: mm)

10.0

12.0

34

44

0.80

22

12

12.0

0 ~ 0.2

0°∼10°

0.60

±

0.20

 Material & Lead finish

Package molding compound: Epoxy

Lead frame material: Cu

Lead frame surface treatment: Solder (Pb free) plate

[AK5365]

MS0164-E-02 2012/12

- 42 -

MARKING

1

AKM

AK5365VQ

XXXXXXX

XXXXXXX : Date Code Identifier (7 digits)

REVISION HISTORY

Date (Y/M/D) Revision Reason Page Contents

02/07/15 00 First Edition

02/08/08 01 Specification

Change

Error Correction

7

8

S/(N+D) min : 86dB → 84dB@fs=48kHz

: 84dB → 82dB@fs=96kHz

Passband : ±0.005dB → −0.005dB

12/12/10 02 Specification

Change 40 PACKAGE

Package dimensions were changed.

[AK5365]

MS0164-E-02 2012/12

- 43 -

IMPORTANT NOTICE

z These products and their specifications are subject to change without notice.

When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei

Microdevices Corporation (AKM) or authorized distributors as to current status of the products.

z Descriptions of external circuits, application circuits, software and other related information contained in this

document are provided only to illustrate the operation and application exampl es of the sem iconductor products. You

are fully responsible for the incorporation of these external circuits, application circuits, software and other related

information in the design of your equipments. AKM assum es no responsibility for any losses incurred by you or third

parties arising from the use of these information herein. AKM assumes no liability for infringement of any p atent,

intellectual property, or other rights in the application or use of such information contained herein.

z Any export of these products, or devices or systems containing them, may require an export license or other official

approval under the law and regulati ons of the country of export pertaini ng to customs and tariffs, currency exchange,

or strategic materials.

z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or

other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use

approved with the express written consent by Represen tative Director of AKM. As used here:

Note1) A critical com ponent is one whose failure to function or perform m ay reasonably be expected to resul t,

whether directly or indirectly, i n the loss of the safety or effect iveness of the device or system containi ng it, and

which must therefore meet very high standards of performance and reliability.

Note2) A hazard related device or system is one designed or intended for life support or ma intenance of safety

or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or

perform may reasonably be expected to result in loss of life or in significant injury or damage to person or

property.

z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places

the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer

or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all

claims arising from the use of said product in the absence of such notification.