SY100EP11UZITR - Micron Technology, Inc.

DESCRIPTION

FEATURES

2.5V/3.3V/5V 1:2 DIFFERENTIAL

PECL/LVPECL/ECL

FANOUT BUFFER

PIN CONFIGURATION/BLOCK DIAGRAM

VCC

VEE

/Q0

/Q1 V

75kΩ

8-pin MSOP and SOIC Packages

ECL Pro™

SY10EP11U

SY100EP11U

FINAL

■2.5V, 3.3V and 5V power supply options

■Guaranteed AC parameters over temperature:

•f

MAX > 3.0GHz

• < 20ps output-to-output skew

• < 200ps tr/t

• < 300ps propagation delay

■Wide temperature range: –40°C to +85°C

■Available in 8-pin (3mm) MSOP and SOIC packages

The SY10/100EP11U is a precision, high-speed 1:2

differential fanout buffer. Having within-device skews and

output transition times significantly improved over the

EL11V, the EP11U is ideally suited for those applications

which require the ultimate in AC performance.

The differential inputs of the EP11U employ clamping

circuitry to maintain stability under open input conditions.

If the inputs are left open, the Q outputs will go LOW.

Rev.: C Amendment: /0

Issue Date: October 2002

Pin Function

D PECL, LVPECL, ECL, LVECL Clock or Data Input:

Internal 75kΩ pulldown resistor. If left floating,

pin defaults LOW, QOUT goes LOW.

/D PECL, LVPECL, ECL, LVECL complementary

Clock or Data Input: Internal 75kΩ pull-up and

down resistors. If left open, default is VCC/2. When

the input is not used, it can be left open.

Q0, /Q0 PECL, LVPECL, ECL, LVECL Outputs:

Q1, /Q1 Terminates to VCC –2V.

VCC Positive Power Supply: Bypass with 0.1µF//0.01µF

low ESR capacitors.

VEE Negative Power Supply: For PECL operation,

connect to GND.

PIN NAMES

Micrel Semiconductor ON Semiconductor

SY10EP11UZI/KI MC10EP11D/DT

SY10EP11UZI/KI MC10LVEP11D/DT

SY100EP11UZI/KI MC100EP11D/DT

SY100EP11UZI/KI MC100LVEP11D/DT

CROSS REFERENCE TABLE

ECL Pro™

ECL Pro is a trademark of Micrel, Inc.

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

Symbol Rating Value Unit

VCC —V

EE Power Supply Voltage 6V V

VIN Input Voltage (VCC = 0V, VIN not more negative than VEE) –6.0 to 0 V

Input Voltage (VEE = 0V, VIN not more positive than VCC) +6.0 to 0 V

IOUT Output Current –Continuous 50 mA

–Surge 100

TAOperating Temperature Range –40 to +85 °C

Tstore Storage Temperature Range –65 to +150 °C

θJA Package Thermal Resistance –Still-Air (SOIC) 160 °C/W

(Junction-to-Ambient) –500lfpm (SOIC) 109

–Still-Air (MSOP) 206 °C/W

–500lfpm (MSOP) 155

θJC Package Thermal Resistance (SOIC) 39 °C/W

(Junction-to-Case) (MSOP) 39

ABSOLUTE MAXIMUM RATINGS(1)

NOTE:

1. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. This is a stress rating only and functional operation is not implied

at conditions other than those detailed in the operational sections of this data sheet. Exposure to ABSOLUTE MAXIMUM RATlNG conditions for extended

periods may affect device reliability.

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VCC Power Supply Voltage V

(PECL) 4.5 5.0 5.5 4.5 5.0 5.5 4.5 5.0 5.5

(LVPECL) 2.37 — 3.8 2.37 — 3.8 2.37 — 3.8

(ECL) –5.5 –5.0 –4.5 –5.5 –5.0 –4.5 –5.5 –5.0 –4.5

(LVECL) –3.8 –3.3 –2.37 –3.8 –3.3 –2.37 –3.8 –3.3 –2.37

IEE Power Supply Current

SY10EP11U — — 37 — 25 39 — — 40 mA

SY100EP11U — — 44 — 30 44 — — 44 mA

IIH Input HIGH Current — — 150 — — 150 — — 150 µAV

IN = VIH

IIL Input LOW Current D 0.5 — — 0.5 — — 0.5 — — µAV

IN = VIL

/D –150 — — –150 — — –150 — — µAV

IN = VIL

CIN Input Capacitance (MSOP) — — — — 1.0 ————pF

(SOIC) — — — — 1.35 ————pF

DC ELECTRICAL CHARACTERISTICS(1)

NOTES:

1. 10/100KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is

in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained.

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VOL Output LOW Voltage 565 690 815 630 755 880 690 815 940 mV

50Ω to VCC–2V

VOH Output HIGH Voltage 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) 1.2 — VCC 1.2 — VCC 1.2 — VCC V

Common Mode Range

(10KEP) LVPECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 2.5V ±5%, VEE = 0V

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VIL Input LOW Voltage 1365 — 1690 1430 — 1755 1490 — 1815 mV

(Single-Ended)

VIH Input HIGH Voltage 2090 — 2415 2155 — 2480 2215 — 2540 mV

(Single-Ended)

VOL Output LOW Voltage 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV

50Ω to VCC–2V

VOH Output HIGH Voltage 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) 1.2 — VCC 1.2 — VCC 1.2 — VCC V

Common Mode Range

(10KEP) LVPECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 3.3V ±10%, VEE = 0V

NOTES:

1. 10KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test

socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Input and output parameters are at VCC = 2.5V. They

vary 1:1 with VCC.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VCC ≥3.0V in PECL mode.

NOTES:

1. 10KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test

socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Input and output parameters are at VCC = 3.3V. They

vary 1:1 with VCC.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VCC ≥3.0V in PECL mode.

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VIL Input LOW Voltage 3065 — 3390 3130 — 3455 3190 — 3515 mV

(Single-Ended)

VIH Input HIGH Voltage 3790 — 4115 3855 — 4180 3915 — 4240 mV

(Single-Ended)

VOL Outuput LOW Voltage 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV

50Ω to VCC–2V

VOH Output HIGH Voltage 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) 1.2 — VCC 1.2 — VCC 1.2 — VCC V

Common Mode Range

(10KEP) PECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 5.0V ±10%, VEE = 0V

NOTES:

1. 10KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test

socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Input and output parameters are at VCC = 5.0V. They

vary 1:1 with VCC.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VCC ≥3.0V in PECL mode.

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VIL Input LOW Voltage –1935 — –1610 –1870 — –1545 –1810 — –1485 mV

(Single-Ended)

VIH Input HIGH Voltage –1210 — –885 –1145 — –820 –1085 — –760 mV

(Single-Ended)

VOL Outuput LOW Voltage –1935 –1810 –1685 –1870 –1745 –1620 –1810 –1685 –1560 mV

50Ω to VCC–2V

VOH Output HIGH Voltage –1135 –1010 –885 –1070 –945 –820 –1010 –885 –760 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) VEE +1.2 0.0 VEE +1.2 0.0 VEE +1.2 0.0 V

Common Mode Range

(10KEP) ECL/LVECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 0V, VEE = –5.5V to –2.375V

NOTES:

1. 10KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test

socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VEE ≤–3.0V in ECL/LVECL mode.

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VOL Outuput LOW Voltage 555 680 805 555 680 805 555 680 805 mV

50Ω to VCC–2V

VOH Output HIGH Voltage 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) 1.2 — VCC 1.2 — VCC 1.2 — VCC V

Common Mode Range

(100KEP) LVPECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 2.5V ±5%

NOTES:

1. 100KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a

test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Input and output parameters are at VCC = 2.5V.

They vary 1:1 with VCC.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VCC ≥3.0V in PECL mode.

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VIL Input LOW Voltage 1355 — 1675 1355 — 1675 1355 — 1675 mV

(Single-Ended)

VIH Input HIGH Voltage 2075 — 2420 2075 — 2420 2075 — 2420 mV

(Single-Ended)

VOL Output LOW Voltage 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV

50Ω to VCC–2V

VOH Output HIGH Voltage 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) 1.2 — VCC 1.2 — VCC 1.2 — VCC V

Common Mode Range

(100KEP) LVPECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 3.3V ±10%, VEE = 0V

NOTES:

1. 100KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a

test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Input and output parameters are at VCC = 3.3V.

They vary 1:1 with VCC.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VCC ≥3.0V in PECL mode.

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VIL Input LOW Voltage 3055 — 3375 3055 — 3375 3055 — 3375 mV

(Single-Ended)

VIH Input HIGH Voltage 3775 — 4120 3775 — 4120 3775 — 4120 mV

(Single-Ended)

VOL Outuput LOW Voltage 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV

50Ω to VCC–2V

VOH Output HIGH Voltage 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) 2.0 — VCC 2.0 — VCC 2.0 — VCC V

Common Mode Range

(100KEP) PECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 5.0V ±10%, VEE = 0V

NOTES:

1. 100KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a

test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Input and output parameters are at VCC = 5.0V.

They vary 1:1 with VCC.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VCC ≥3.0V in PECL mode.

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

VIL Input LOW Voltage –1945 — –1625 –1945 — –1625 –1945 — –1625 mV

(Single-Ended)

VIH Input HIGH Voltage –1225 — –880 –1225 — –880 –1225 — –880 mV

(Single-Ended)

VOL Outuput LOW Voltage –1945 –1820 –1695 –1945 –1820 –1695 –1945 –1820 –1695 mV

50Ω to VCC–2V

VOH Output HIGH Voltage –1145 –1020 –895 –1145 –1020 –895 –1145 –1020 –895 mV

50Ω to VCC–2V

VIHCMR Input HIGH Voltage(2) VEE +1.2 0.0 VEE +1.2 0.0 VEE +1.2 0.0 V

Common Mode Range

(100KEP) ECL/LVECL DC ELECTRICAL CHARACTERISTICS(1)

VCC = 0V, VEE = –5.5V to –2.375V

NOTES:

1. 100KEP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a

test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained.

2. The VIHCMR range is referenced to the most positive side of the differential input signal. See “Input Waveform” section. Single-ended input CLK pin operation

is limited to VEE ≤–3.0V in ECL/LVECL mode.

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

TA = –40°CT

A = +25°CT

A = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Condition

fMAX Max. Toggle Frequency(1) 3 — — 3 — — 3 — — GHz

tPLH Propagation Delay (Differential)

tPHL D to Q, /Q 140 200 250 160 220 270 180 240 300 ps

= 3.3V/5V

D to Q, /Q 170 230 300 180 240 310 210 270 360 ps VCC = 2.5V

tSKEW Within-Device Skew(2) Q, /Q — 5 20 — 5 20 — 5 20 ps

Part-to-Part Skew(2) — — 130 — — 130 — — 150 ps

= 3.3V/5V

— — 110 — — 110 — — 120 ps VCC = 2.5V

tJITTER Cycle-to-Cycle Jitter (rms) — 0.2 < 1 — 0.2 < 1 — 0.2 < 1 ps rms

VDIFF Input Swing(3) 150 800 1200 150 800 1200 150 800 1200 mV

tr, tfOutput Rise/Fall Time 70 110 170 80 120 180 100 140 200 ps

(20% to 80%)

AC ELECTRICAL CHARACTERISTICS

VCC = 0V; VEE = –5.5V to –2.375V or VCC = 2.375V to 5.5V, VEE = 0V

NOTES:

1. Measured with 750mV input signal, 50% duty cycle. All loading with a 50Ω to VCC –2.0V.

2. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays are measured

from the cross point of the inputs to the cross point of the outputs.

3. See “Input Waveform.”

INPUT WAVEFORM

IHCMR

DIFF

=150mV to 1200mV

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

TERMINATION RECOMMENDATIONS

82Ω

= 50Ω

+3.3V +3.3V

= V

–2V

130Ω

+3.3V

Figure 1. Parallel Termination–Thevenin Equivalent

Notes:

1. For +2.5V systems:

R1 = 250Ω

R2 = 62.5Ω

2. For +5.0V systems:

R1 = 82Ω

R2 = 130Ω

= 50Ω

50Ω50Ω

50Ω

+5.0V or

+3.3V

+5.0V or

+3.3V

“source”“destination”

Figure 2. Three-Resistor “Y–Termination”

Notes:

1. Power-saving alternative to Thevenin termination.

2. Place termination resistors as close to destination inputs as possible.

3. Rb resistor sets the DC bias voltage equal to Vt. For +3.3V systems Rb = 46Ω to 50Ω. For +5V systems, Rb = 110Ω.

Ordering Package Operating Package

Code Type Range Marking

SY100EP11UKI K8-1 Industrial XP11

SY100EP11UKITR* K8-1 Industrial XP11

SY100EP11UZI Z8-1 Industrial XEP11U

SY100EP11UZITR* Z8-1 Industrial XEP11U

PRODUCT ORDERING CODE

Ordering Package Operating Package

Code Type Range Marking

SY10EP11UKI K8-1 Industrial HP11

SY10EP11UKITR* K8-1 Industrial HP11

SY10EP11UZI Z8-1 Industrial HEP11U

SY10EP11UZITR* Z8-1 Industrial HEP11U

*Tape and Reel

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

8 LEAD MSOP (K8-1)

Rev. 01

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

8 LEAD SOIC .150" WIDE (Z8-1)

Rev. 03

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

ECL Pro™

SY10EP11U

SY100EP11U

Micrel

MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA

TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB http://www.micrel.com

This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or

other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel, Inc.