IDTQS3245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH(R) PRODUCTS HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH DESCRIPTION: FEATURES: * * * * * * * * IDTQS3245 The QS3245 provides a set of eight high-speed CMOS TTL-compatible bus switches in a pinout compatible with 74FCT245, 74F245, 74ALS/AS/ LS245 8-bit transceivers. The low ON resistance of the QS3245 allows inputs to be connected to outputs without adding propagation delay and without generating additional ground bounce noise. The Output Enable (OE) signal turns the switches on similar to the OE signal of the 74'245. QuickSwitch devices provide an order of magnitude faster speed than conventional logic devices. The QS3245 is characterized for operation at -40C to +85C. Enhanced N channel FET with no inherent diode to Vcc bidirectional switches connect inputs to outputs 5 Pin compatible with the 74F245, 74FCT245, and 74FCT245T Low power CMOS proprietary technology Zero propagation delay, zero ground bounce Undershoot clamp diodes on all switch and control inputs TTL-compatible control inputs Available in SOIC and QSOP packages APPLICATIONS: * * * * * * * Hot-swapping, hot-docking Voltage translation (5V to 3.3V) Power conservation Capacitance reduction and isolation Logic replacement (data processing) Clock gating Bus switching and isolation FUNCTIONAL BLOCK DIAGRAM A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B2 B3 B4 B5 B6 B7 OE The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE c 2011 Integrated Device Technology, Inc. FEBRUARY 2011 1 DSC-5753/5 IDTQS3245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS(1) Symbol Description VTERM(2) Max Unit VTERM(3) Supply Voltage to Ground -0.5 to +7 V DC Switch Voltage Vs -0.5 to +7 V DC Input Voltage VIN NC 1 20 VCC VTERM(3) -0.5 to +7 V 19 OE AC Input Voltage (pulse width 20ns) -3 V A0 2 VAC IOUT DC Output Current 120 mA PMAX Maximum Power Dissipation (TA = 85C) 0.5 W TSTG Storage Temperature -65 to +150 C A1 3 18 B0 A2 4 17 B1 A3 5 16 B2 A4 6 15 B3 A5 7 14 B4 A6 8 13 B5 A7 9 12 B6 GND 10 11 B7 NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Vcc terminals. 3. All terminals except Vcc. CAPACITANCE (TA = +25C, f = 1.0MHZ, VIN = 0V, VOUT = 0V) SOIC/ QSOP TOP VIEW Pins Typ. Max.(1) Unit Control Pins 3 5 pF 5 7 pF Quickswitch Channels (Switch OFF) NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION Pin Names Description OE Output Enable Ax Data I/Os Bx Data I/Os FUNCTION TABLE(1) OE Outputs H Disconnected L Ax = Bx NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level 2 IDTQS3245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 5% Symbol Parameter Test Conditions Min. Typ.(1) Max. Unit 2 -- -- V VIH Input HIGH Level Guaranteed Logic HIGH for Control Pins VIL Input LOW Level Guaranteed Logic LOW for Control Pins -- -- 0.8 V IIN Input LeakageCurrent (Control Inputs) 0V VIN VCC -- -- 1 A IOZ Off-State Output Current (Hi-Z) 0V VOUT VCC, Switches OFF -- 0.001 1 A RON Switch ON Resistance Pass Voltage(2) -- -- 3.7 5 10 4 7 15 4.2 VP VCC = Min., VIN = 0V, ION = 30mA VCC = Min., VIN = 2.4V, ION =15mA VIN = VCC = 5V, IOUT = -5A NOTES: 1. Typical values are at VCC = 5.0V, TA = 25C. 2. Pass Voltage is guaranteed but not production tested. TYPICAL ON RESISTANCE vs VIN AT VCC = 5V 16 R ON (ohms) 14 12 10 8 6 4 2 0 0.0 0.5 1.0 1.5 2.0 V IN (Volts) 3 2.5 3.0 3.5 V IDTQS3245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol Test Conditions(1) Parameter Max. Unit ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or Vcc, f = 0 3 A ICC Power Supply Current per Control Input HIGH (2) VCC = Max., VIN = 3.4V, f = 0 1.5 mA ICCD Dynamic Power Supply Current per MHz(3) VCC = Max., A and B pins open 0.25 mA/MHz Control Inputs Toggling at 50% Duty Cycle NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Per TLL driven input (VIN = 3.4V, control inputs only). A and B pins do not contribute to Icc. 3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is guaranteed but not production tested. SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40C to +85C, VCC = 5.0V 5%; CLOAD = 50pF, RLOAD = 500 unless otherwise noted. Symbol Parameter tPLH Data Propagation Delay (2,3) tPHL An to/from Bn tPZL Switch Turn-on Delay tPZH OE to Ax/Bx tPLZ Switch Turn-off Delay (2) tPHZ OE to Ax/Bx Min. (1) Typ. Max. Unit -- -- 0.25 ns 0.5 -- 5.6 ns 0.5 -- 4.5 ns NOTES: 1. Minimums are guaranteed but not production tested. 2. This parameter is guaranteed but not production tested. 3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4 IDTQS3245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION QS XXXXX Device Type XX Package X Process X Blank 8 Tube or Tray Tape and Reel Blank Industrial (-40C to +85C) SOG QG Small Outline IC - Green Quarter Size Outline Package - Green 3245 High Speed CMOS Quickswitch 8-Bit Bus Switch Datasheet Document History 02/14/2011 Pg. 5 Updated the ordering information by removing the "IDT" notation, non RoHS part and by adding Tape and Reel information. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 5 for Tech Support: logichelp@idt.com