W3E32M72SR-XSBX 32Mx72 REGISTERED DDR SDRAM FEATURES BENEFITS Registered for enhanced performance of bus speeds of 200, 250, 266Mb/s 74% SPACE SAVINGS vs. TSOP Package: 51% I/O reduction vs TSOP Reduced part count * 208 Plastic Ball Grid Array (PBGA), 16 x 25mm Glueless connection to PCI bridge/memory controller 2.5V 0.2V core power supply Reduced trace lengths for lower parasitic capacitance 2.5V I/O (SSTL_2 compatible) Suitable for hi-reliability applications Differential clock inputs (CK and CK#) Laminate interposer for optimum TCE match Commands entered on each positive CK edge Internal pipelined double-data-rate (DDR) architecture; two data accesses per clock cycle * This product is subject to change or cancellation without notice. Programmable Burst length: 2,4 or 8 GENERAL DESCRIPTION Bidirectional data strobe (DQS) transmitted/received with data, i.e., source-synchronous data capture (one per byte) The 256MByte (2Gb) DDR SDRAM is a high-speed CMOS, dy nam ic ran dom-access, memory using 5 chips containing 536,870,912 bits. Each chip is internally configured as a quadbank DRAM. DQS edge-aligned with data for READs; center-aligned with data for WRITEs The 256MB DDR SDRAM uses a double data rate architecture to achieve high-speed operation. The double data rate architecture is essentially a 2n-prefetch architecture with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the 256MB DDR SDRAM effectively consists of a single 2n-bit wide, one-clock-cycle data tansfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins. DLL to align DQ and DQS transitions with CK Four internal banks for concurrent operation Data mask (DM) pins for masking write data (one per byte) Programmable IOL/IOH option Auto precharge option Auto Refresh and Self Refresh Modes A bi-directional data strobe (DQS) is transmitted externally, along with data, for use in data capture at the receiver.strobe transmitted by the DDR SDRAM during READs and by the memory contoller during WRITEs. DQS is edge-aligned with data for READs and center-aligned with data for WRITEs. Each chip has two data strobes, one for the lower byte and one for the upper byte. Commercial, Industrial and Military Temperature Ranges Organized as 32M x 72 Weight: W3E32M72SR-XSBX - 2.5 grams typical DENSITY COMPARISONS Monolithic Solution (mm) 11.9 11.9 11.9 W3E32M72SR-XSBX 11.9 8.3 11.9 12.6 22.3 66 TSOP 66 TSOP 66 TSOP 66 TSOP 48 TSOP 66 TSOP 16 W3E32M72SR-XBX 12.6 48 TSOP 25 S A V I N G S Area 5 x 265mm2 + 2 x 105mm2 = 1536mm2 400mm2 74% I/O Count 5 x 66 pins + 2 x 48 pins = 426 pins 208 Balls 51% Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 1 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX The 256MB DDR SDRAM operates from a differential clock (CK and CK#); the crossing of CK going HIGH and CK# going LOW will be referred to as the positive edge of CK. Commands (address and control signals) are registered at every positive edge of CK. Input data is registered on both edges of DQS, and output data is referenced to both edges of DQS, as well as to both edges of CK. remain as such until power is cycled. Maintaining an LVCMOS LOW level on CKE during power-up is required to ensure that the DQ and DQS outputs will be in the High-Z state, where they will remain until driven in normal operation (by a read access). After all power supply and reference voltages are stable, and the clock is stable, the DDR SDRAM requires a 200s delay prior to applying an executable command. Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed. The address bits registered coincident with the READ or WRITE command are used to select the bank and the starting column location for the burst access. Once the 200s delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a LOAD MODE REGISTER command should be issued for the extended mode register (BA1 LOW and BA0 HIGH) to enable the DLL, followed by another LOAD MODE REGISTER command to the mode register (BA0/BA1 both LOW) to reset the DLL and to program the operating parameters. Twohundred clock cycles are required between the DLL reset and any READ command. A PRECHARGE ALL command should then be applied, placing the device in the all banks idle state. The DDR SDRAM provides for programmable READ or WRITE burst lengths of 2, 4, or 8 locations. An auto precharge function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst access. Once in the idle state, two AUTO REFRESH cycles must be performed (tRFC must be satisfied.) Additionally, a LOAD MODE REGISTER command for the mode register with the reset DLL bit deactivated (i.e., to program operating parameters without resetting the DLL) is required. Following these requirements, the DDR SDRAM is ready for normal operation. The pipelined, multibank architecture of DDR SDRAMs allows for concurrent operation, thereby providing high effective bandwidth by hiding row precharge and activation time. An auto refresh mode is provided, along with a power-saving power-down mode. All inputs are compatible with the Jedec Standard for SSTL_2. All full drive options outputs are SSTL_2, Class II compatible. REGISTER DEFINITION MODE REGISTER FUNCTIONAL DESCRIPTION The Mode Register is used to define the specific mode of operation of the DDR SDRAM. This definition includes the selection of a burst length, a burst type, a CAS latency, and an operating mode, as shown in Figure 3. The Mode Register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. (Except for bit A8 which is self clearing). Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed (BA0 and BA1 select the bank, A0-12 select the row). The address bits registered coincident with the READ or WRITE command are used to select the starting column location for the burst access. Reprogramming the mode register will not alter the contents of the memory, provided it is performed correctly. The Mode Register must be loaded (reloaded) when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating the subsequent operation. Violating either of these requirements will result in unspecified operation. Prior to normal operation, the DDR SDRAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command descriptions and device operation. Mode register bits A0-A2 specify the burst length, A3 specifies the type of burst (sequential or interleaved), A4-A6 specify the CAS latency, and A7-A12 specify the operating mode. INITIALIZATION DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in undefined operation. Power must first be applied to VCC and VCCQ simultaneously, and then to VREF (and to the system VTT). VTT must be applied after VCCQ to avoid device latch-up, which may cause permanent damage to the device. VREF can be applied any time after VCCQ but is expected to be nominally coincident with VTT. Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input but will detect an LVCMOS LOW level after VCC is applied. After CKE passes through VIH, it will transition to an SSTL_2 signal and BURST LENGTH Read and write accesses to the DDR SDRAM are burst oriented, with the burst length being programmable, as shown in Figure 3. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command. Burst lengths of 2, 4 or 8 locations are available for both the sequential and the interleaved burst types. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 2 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX FIGURE 1 - PIN CONFIGURATION Top View 1 A 2 3 4 5 6 7 8 9 10 11 VCC VSS VCCQ VCCQ VSS VCCQ VCCQ VSS VCC VSS B VCCQ VSS NC NC NC NC NC NC NC VSS VCCQ C VSS CK0# CK2# CK0 CK2 DM0 DM4 NC NC NC VSS D DM5 DM1 DQS5 DQS1 DQ8 DQ40 DQ5 DQ39 DQ7 DQS4 DQS0 E DQ41 DQ9 DQ10 DQ42 DQ43 DQ12 DQ3 DQ36 DQ4 DQ38 DQ6 F DQ44 DQ11 DQ13 DQ45 DQ14 DQ33 DQ1 DQ34 DQ2 DQ37 DQ35 G DQ64 DQ65 DQ15 DQ47 DQ46 VSS DQ32 DQ0 DQ77 DQ79 DQ78 H CAS# DQ66 DQ69 RAS# DQ67 VCC DQ72 DQ73 DQ74 DQ75 DQ76 J VCCQ A12 BA1 A0 VCC VSS VCCQ A7 A9 DNU* VCC K VSS A10 A3 VCCQ VSS VREF VSS VCCQ A4 A11 VSS L VCC A2 BA0 A1 VCCQ VSS VCC A6 A8 A5 VCCQ M DQ71 DQ70 DQS8 DM8 DQ68 VCC DQS9 DM9 CK4# CK4 RESET# N WE# RCK RCK# DQ16 DQ48 VSS DQ63 DQ31 DQ62 CKE CS# P DQ22 DQ52 DQ18 DQ50 DQ17 DQ49 DQ30 DQ61 DQ29 DQ59 DQ27 R DQ23 DQ54 DQ21 DQ19 DQ51 DQ60 DQ28 DQ58 DQ26 DQ57 DQ25 T DQS2 DQS6 DQ55 DQ53 DQ20 DQ56 DQ24 DM7 DM3 DQS3 DQS7 U VSS NC NC NC DM6 DM2 CK1# CK3# CK1 CK3 VSS V VCCQ VSS NC NC NC NC NC NC NC VSS VCCQ W VSS VCC VSS VCCQ VCCQ VSS VCCQ VCCQ VSS VCC VSS * pin J10 is reserved for signal A13 on future upgrades. NOTE: DNU = Do Not Use. Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 3 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX FIGURE 2 - FUNCTIONAL BLOCK DIAGRAM CSB# WEB# RAS B# CAS B# CS# WE# RAS# CAS# VREF VREF A0-12 BA0-1 RCK RCK# CK CK0 CK0# CKEB DM0 DM1 CK CK# CKE DQML DQMH DQS0 DQS1 DQSL DQSH CK# VREF A0-12 BA0-1 SSTV16857 BA0-1 IC6 VREF RESET# CK CK1 CK1# CKEB DM2 DM3 CK CK# CKE DQML DQMH DQS2 DQS3 DQSL DQSH CASB# SSTV16857 WE# IC7 CS# A0-12 WEB# CSB# CKEB CKE DQ16 = Y = Y = Y = Y = Y = Y DQ31 VREF RASB# RAS# IC2 DQ0 = Y = Y = Y = Y = Y = Y DQ15 CS# WE# RAS# CAS# CK# CAS# DQ0 = Y = Y = Y = Y = Y = Y DQ15 CS# WE# RAS# CAS# A0-12 RESET# IC1 DQ0 = Y = Y = Y = Y = Y = Y DQ15 VREF RESET# CK2 CK2# CKEB BA0-1 CK CK# CKE DM4 DM5 DQS4 DQS5 DQML DQMH DQSL DQSH IC3 DQ0 = Y = Y = Y = Y = Y = Y DQ15 DQ32 = Y = Y = Y = Y = Y = Y DQ47 CS# WE# RAS# CAS# VREF A0-12 CK3 CK3# CKEB DM6 DM7 DQS6 DQS7 BA0-1 CK CK# CKE DQML DQMH DQSL DQSH IC4 DQ0 = Y = Y = Y = Y = Y = Y DQ15 DQ48 = Y = Y = Y = Y = Y = Y DQ63 CS# WE# RAS# CAS# VREF A0-12 CK4 CK4# CKEB DM8 DM9 BA0-1 CK CK# CKE DQML DQMH DQS8 DQS9 DQSL DQSH IC5 DQ0 = Y = Y = Y = Y = Y = Y DQ15 DQ64 = Y = Y = Y = Y = Y = Y DQ79 Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 4 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the burst will wrap within the block if a boundary is reached. The block is uniquely selected by A1-Ai when the burst length is set to two; by A2-Ai when the burst length is set to four (where Ai is the most significant column address for a given configuration); and by A3-Ai when the burst length is set to eight. The remaining (least significant) address bit(s) is (are) used to select the starting location within the block. The programmed burst length applies to both READ and WRITE bursts. TABLE 1 - BURST DEFINITION Burst Length A12 A11 A10 A9 BA0 14 13 0* 0* 12 11 10 9 A8 8 7 Operating Mode A7 A6 6 A5 5 A3 A4 4 3 CAS Latency BT A2 2 A1 1 0 A0 2 Address Bus Mode Register (Mx) 8 Burst Length M2 M1 M0 M3 = 1 M3 = 0 0 0 0 Reserved 0 0 1 2 2 0 1 0 4 4 0 1 1 8 8 1 0 0 Reserved Reserved 1 0 1 Reserved Reserved 1 1 0 Reserved Reserved 1 1 1 Reserved Reserved 0 Sequential 1 Interleaved M6 M5 M4 0 0-1 0-1 1 1-0 1-0 A0 0 0 0-1-2-3 0-1-2-3 0 1 1-2-3-0 1-0-3-2 1 0 2-3-0-1 2-3-0-1 1 1 3-0-1-2 3-2-1-0 A2 A1 A0 0 0 0 0-1-2-3-4-5-6-7 0-1-2-3-4-5-6-7 0 0 1 1-2-3-4-5-6-7-0 1-0-3-2-5-4-7-6 0 1 0 2-3-4-5-6-7-0-1 2-3-0-1-6-7-4-5 0 1 1 3-4-5-6-7-0-1-2 3-2-1-0-7-6-5-4 1 0 0 4-5-6-7-0-1-2-3 4-5-6-7-0-1-2-3 1 0 1 5-6-7-0-1-2-3-4 5-4-7-6-1-0-3-2 1 1 0 6-7-0-1-2-3-4-5 6-7-4-5-2-3-0-1 1 1 1 7-0-1-2-3-4-5-6 7-6-5-4-3-2-1-0 Reserved NOTES: 1. For a burst length of two, A1-Ai select two-data-element block; A0 selects the starting column within the block. 2. For a burst length of four, A2-Ai select four-data-element block; A0-1 select the starting column within the block. 3. For a burst length of eight, A3-Ai select eight-data-element block; A0-2 select the starting column within the block. 4. Whenever a boundary of the block is reached within a given sequence above, the following access wraps within the block. Burst Type M3 Type = Interleaved A1 4 Burst Length * M14 and M13 (BA0 and BA1 must be "0, 0" to select the base mode register (vs. the extended mode register). Type = Sequential A0 FIGURE 3 - MODE REGISTER DEFINITION BA1 Order of Accesses Within a Burst Starting Column Address CAS Latency 0 0 0 Reserved 0 0 1 Reserved 0 1 0 2 0 1 1 Reserved 1 0 0 Reserved 1 0 1 Reserved 1 1 0 2.5 1 1 1 Reserved M12 M11 M10 M9 M8 M7 M6-M0 0 0 0 0 0 0 Valid Normal Operation 0 0 0 0 1 0 Valid Normal Operation/Reset DLL - - - - - - - READ LATENCY The READ latency is the delay, in clock cycles, between the registration of a READ command and the availability of the first bit of output data. The latency can be set to 2 or 2.5 clocks. If a READ command is registered at clock edge n, and the latency is m clocks, the data will be available by clock edge n+m. Table 2 below indicates the operating frequencies at which each CAS latency setting can be used. Operating Mode Reserved states should not be used as unknown operation or incompatibility with future versions may result. All other states reserved TABLE 2 - CAS LATENCY BURST TYPE ALLOWABLE OPERATING FREQUENCY (MHz) Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the burst type and is selected via bit M3. CAS LATENCY = 2 CAS LATENCY = 2.5 -200 75 100 -250 100 125 -266 100 133 SPEED The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column address, as shown in Table 1. OPERATING MODE The normal operating mode is selected by issuing a MODE REGISTER SET command with bits A7-A12 each set to zero, Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 5 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX and bits A0-A6 set to the desired values. A DLL reset is initiated by issuing a MODE REGISTER SET command with bits A7 and A9-A12 each set to zero, bit A8 set to one, and bits A0-A6 set to the desired values. Although not required, JEDEC specifications recommend when a LOAD MODE REGISTER command is issued to reset the DLL, it should always be followed by a LOAD MODE REGISTER command to select normal operating mode. OUTPUT DRIVE STRENGTH The normal full drive strength for all outputs are specified to be SSTL2, Class II. The DDR SDRAM supports an option for reduced drive. This option is intended for the support of the lighter load and/ or point-to-point environments. The selection of the reduced drive strength will alter the DQs and DQSs from SSTL2, Class II drive strength to a reduced drive strength, which is approximately 54 percent of the SSTL2, Class II drive strength. All other combinations of values for A7-A12 are reserved for future use and/or test modes. Test modes and reserved states should not be used because unknown operation or incompatibility with future versions may result. DLL ENABLE/DISABLE When the part is running without the DLL enabled, device functionality may be altered. The DLL must be enabled for normal operation. DLL enable is required during power-up initialization and upon returning to normal operation after having disabled the DLL for the purpose of debug or evaluation. (When the device exits self refresh mode, the DLL is enabled automatically.) Any time the DLL is enabled, 200 clock cycles with CKE high must occur before a READ command can be issued. EXTENDED MODE REGISTER The extended mode register controls functions beyond those controlled by the mode register; these additional functions are DLL enable/disable, output drive strength, and QFC. These functions are controlled via the bits shown in Figure 5. The extended mode register is programmed via the LOAD MODE REGISTER command to the mode register (with BA0 = 1 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. The enabling of the DLL should always be followed by a LOAD MODE REGISTER command to the mode register (BA0/ BA1 both LOW) to reset the DLL. COMMANDS The Truth Table provides a quick reference of available commands. This is followed by a written description of each command. The extended mode register must be loaded when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating any subsequent operation. Violating either of these requirements could result in unspecified operation. DESELECT The DESELECT function (CS# High) prevents new commands from being executed by the DDR SDRAM. The SDRAM is effectively deselected. Operations already in progress are not affected. FIGURE 4 - CAS LATENCY T0 T1 T2 FIGURE 5 - EXTENDED MODE REGISTER DEFINITION T2n T3 T3n CLK# CLK COMMAND BA1 BA0 A12 A11 A10 A9 READ NOP NOP A8 A7 A6 A5 A4 A3 4 3 2 A2 A0 A1 Address Bus NOP 14 13 12 11 10 9 8 CL = 2 01 11 7 6 5 Operating Mode 1 0 DS DLL Extended Mode Register (Ex) DQS DQ T0 T1 T2 T2n T3 T3n E0 DLL 0 Enable 1 Disable CLK# E1 CLK COMMAND READ NOP NOP NOP Drive Strength 0 Normal 1 Reduced CL = 2.5 DQS DQ E8 E7 E6 E5 E4 E3 E2 E1, E0 Operating Mode 0 0 0 0 0 0 0 0 0 0 0 Valid Reserved - - - - - - - - - - - - Reserved E12 E11 E10 E9 Burst Length = 4 in the cases shown Shown with nominal tAC and nominal tDSDQ DATA TRANSITIONING DATA 1. E14 and E13 must be "0, 1" to select the Extended Mode Register (vs. the base Mode Register) 2. The QFC# function is not supported. DON'T CARE Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 6 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX parameters. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command will be treated as a NOP if there is no open row in that bank (idle state), or if the previously open row is already in the process of precharging. NO OPERATION (NOP) The NO OPERATION (NOP) command is used to perform a NOP to the selected DDR SDRAM (CS# is LOW while RAS#, CAS#, and WE# are high). This prevents unwanted commands from being registered during idle or wait states. Operations already in progress are not affected. LOAD MODE REGISTER The Mode Registers are loaded via inputs A0-12. The LOAD MODE REGISTER command can only be issued when all banks are idle, and a subsequent executable command cannot be issued until tMRD is met. AUTO PRECHARGE AUTO PRECHARGE is a feature which performs the same individual-bank PRECHARGE function described above, but without requiring an explicit command. This is accomplished by using A10 to enable AUTO PRECHARGE in conjunction with a specific READ or WRITE command. A precharge of the bank/ row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. AUTO PRECHARGE is nonpersistent in that it is either enabled or disabled for each individual READ or WRITE command. The device supports concurrent auto precharge if the command to the other bank does not interrupt the data transfer to the current bank. ACTIVE The ACTIVE command is used to open (or activate) a row in a particular bank for a subsequent access. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-12 selects the row. This row remains active (or open) for accesses until a PRECHARGE command is issued to that bank. A PRECHARGE command must be issued before opening a different row in the same bank. READ AUTO PRECHARGE ensures that the precharge is initiated at the earliest valid stage within a burst. This "earliest valid stage" is determined as if an explicit precharge command was issued at the earliest possible time, without violating tRAS (MIN).The user must not issue another command to the same bank until the precharge time (tRP) is completed. The READ command is used to initiate a burst read access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-9 selects the starting column location. The value on input A10 determines whether or not AUTO PRECHARGE is used. If AUTO PRECHARGE is selected, the row being accessed will be precharged at the end of the READ burst; if AUTO PRECHARGE is not selected, the row will remain open for subsequent accesses. BURST TERMINATE The BURST TERMINATE command is used to truncate READ bursts (with auto precharge disabled). The most recently registered READ command prior to the BURST TERMINATE command will be truncated. The open page which the READ burst was terminated from remains open. WRITE The WRITE command is used to initiate a burst write access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-9 selects the starting column location. The value on input A10 determines whether or not AUTO PRECHARGE is used. If AUTO PRECHARGE is selected, the row being accessed will be precharged at the end of the WRITE burst; if AUTO PRECHARGE is not selected, the row will remain open for subsequent accesses. Input data appearing on the DQ is written to the memory array subject to the DQM input logic level appearing coincident with the data. If a given DQM signal is registered LOW, the corresponding data will be written to memory; if the DQM signal is registered HIGH, the corresponding data inputs will be ignored, and a WRITE will not be executed to that byte/column location. AUTO REFRESH AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS-BEFORE-RAS (CBR) REFRESH in conventional DRAMs. This command is nonpersistent, so it must be issued each time a refresh is required. All banks must be idle before an AUTO REFRESH command is issued. The addressing is generated by the internal refresh controller. This makes the address bits "Don't Care" during an AUTO REFRESH command. Each DDR SDRAM requires AUTO REFRESH cycles at an average interval of 7.8125s (maximum). PRECHARGE To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM, meaning that the maximum absolute interval between any AUTO REFRESH command and the next AUTO REFRESH command is 9 x 7.8125s (70.3s). This maximum absolute interval is to allow future support for DLL updates internal to the DDR SDRAM to be restricted to AUTO The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access a specified time (tRP) after the PRECHARGE command is issued. Except in the case of concurrent auto precharge, where a READ or WRITE command to a different bank is allowed as long as it does not interrupt the data transfer in the current bank and does not violate any other timing Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 7 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX REFRESH (A DLL reset and 200 clock cycles must then occur before a READ command can be issued). Input signals except CKE are "Don't Care" during SELF REFRESH. VREF voltage is also required for the full duration of SELF REFRESH. REFRESH cycles, without allowing excessive drift in tAC between updates. Although not a JEDEC requirement, to provide for future functionality features, CKE must be active (High) during the AUTO REFRESH period. The AUTO REFRESH period begins when the AUTO REFRESH command is registered and ends tRFC later. The procedure for exiting self refresh requires a sequence of commands. First, CK and CK# must be stable prior to CKE going back HIGH. Once CKE is HIGH, the DDR SDRAM must have NOP commands issued for tXSNR, because time is required for the completion of any internal refresh in progress. SELF REFRESH* The SELF REFRESH command can be used to retain data in the DDR SDRAM, even if the rest of the system is powered down. When in the self refresh mode, the DDR SDRAM retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command except CKE is disabled (LOW). The DLL is automatically disabled upon entering SELF REFRESH and is automatically enabled upon exiting SELF A simple algorithm for meeting both refresh and DLL requirements is to apply NOPs for tXSNR time, then a DLL Reset and NOPs for 200 additional clock cycles before applying any other command. * Self refresh available in commercial and industrial temperatures only. TRUTH TABLE - COMMANDS (NOTE 1) NAME (FUNCTION) DESELECT (NOP) (9) NO OPERATION (NOP) (9) ACTIVE (Select bank and activate row) ( 3) READ (Select bank and column, and start READ burst) (4) WRITE (Select bank and column, and start WRITE burst) (4) BURST TERMINATE (8) PRECHARGE (Deactivate row in bank or banks) ( 5) AUTO REFRESH or SELF REFRESH (Enter self refresh mode) (6, 7) LOAD MODE REGISTER (2) CS# H L L L L L L L L RAS# X H L H H H L L L TRUTH TABLE - DM OPERATION NAME (FUNCTION) DM CAS# X H H L L H H L L WE# X H H H L L L H L ADDR X X Bank/Row Bank/Col Bank/Col X Code X Op-Code REGISTER FUNCTION TABLE RCK# INPUT OUTPUT Q H H H RCK INPUTS L L H L or H L or H X Q0 L X, or floating X, or floating X, or floating L DQs WRITE ENABLE (10) L Valid RESET# WRITE INHIBIT (10) H X H NOTES: 1. CKE is HIGH for all commands shown except SELF REFRESH. 2. A0-12 define the op-code to be written to the selected Mode Register. BA0, BA1 select either the mode register (0, 0) or the extended mode register (1, 0). 3. A0-12 provide row address, and BA0, BA1 provide bank address. 4. A0-9 provide column address; A10 HIGH enables the auto precharge feature (non persistent), while A10 LOW disables the auto precharge feature; BA0, BA1 provide bank address. 5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH: All banks precharged and BA0, BA1 are "Don't Care." 6. 7. This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is LOW. Internal refresh counter controls row addressing; all inputs and I/Os are "Don't Care" except for CKE. 8. Applies only to read bursts with auto precharge disabled; this command is undefined (and should not be used) for READ bursts with auto precharge enabled and for WRITE bursts. 9. DESELECT and NOP are functionally interchangeable. 10. Used to mask write data; provided coincident with the corresponding data. Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 8 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX ABSOLUTE MAXIMUM RATINGS Parameter CAPACITANCE (NOTE 13) Unit Parameter Symbol Max Unit -1 to 3.6 V Input Capacitance: CK/CK# CI1 8 pF -0.5V to VCCQ +0.5V V Addresses, BA0-1 Input Capacitance CA 10 pF Operating Temperature TA (Mil) -55 to +125 C Input Capacitance: All other input-only pins CI2 9 pF Operating Temperature TA (Ind) -40 to +85 C Input/Output Capacitance: I/Os CIO 10 pF Storage Temperature, Plastic -55 to +125 C Voltage on VCC, VCCQ Supply relative to Vss Voltage on I/O pins relative to Vss NOTE: Stress greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions greater than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. BGA THERMAL RESISTANCE Description Symbol Typical Units Notes Junction to Ambient (No Airflow) Theta JA 15.8 C/W 1 Junction to Ball Theta JB 15.7 C/W 1 Junction to Case (Top) Theta JC 7.2 C/W 1 NOTE: These typical thermal resistances are for each DRAM die; if using total power of the MCP, divide above values by five(5). Refer to "PBGA Thermal Resistance Correlation" (Application Note) at www.whiteedc.com in the application notes section for modeling conditions. REGISTER RECOMMENDED OPERATING CONDITIONS Parameter/Condition Min VIH AC high-level input voltage Data inputs VIL AC low-level input voltage Data inputs VIH High-level input voltage RESET# VIL RESET# Low-level input voltage Max VREF+310mV Unit V VREF-310mV 1.7 V V 0.7 V NOTE: The RESET# input of the device must be held at a valid logic level (not floating) to ensure proper device operation. Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 9 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX REGISTER ELECTRICAL CHARACTERISTICS Parameter Test Conditions VCC and VCCQ Min II All inputs VI = VCC or GND 2.7V -5 Static standby RESET# = GND Static operating RESET# = VCC, VI = VIH(AC) or VIL(AC) Dynamic operating - clock only RESET# = VCC, VI = VIH(AC) or VIL(AC), CK and CK# switching 50% duty cycle Dynamic operating - per each data input RESET# = VCC, VI = VIH(AC) or VIL(AC). CK and CK# switching 50% duty cycle. All data input switching at one-half clock frequency, 50% duty cycle ICC ICCD Typ Max Unit +5 A 2.7V IO = 0 IO = 0 10 A 112 mA 56 A/ MHz 180 A/clock MHz 2.5V NOTE: All typical values are at VCC = 2.5V, TA = 25C. DDR DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS (NOTES 1-5, 16) VCC, VCCQ = +2.5V 0.2V; -55C TA +125C Parameter/Condition Symbol Min Max Units Supply Voltage (36, 41) VCC 2.3 2.7 V I/O Supply Voltage (36, 41, 44) VCCQ 2.3 2.7 V Input Leakage Current: Any input 0V VIN VCC (All other pins not under test = 0V) II -2 2 A Output Leakage Current: I/Os are disabled; 0V VOUT VCCQ IOZ -5 5 A Output Levels: Full drive option (37, 39) High Current (VOUT = VCCQ - 0.373V, minimum VREF, minimum VTT) Low Current (VOUT = 0.373V, maximum VREF, maximum VTT) IOH -12 - mA IOL 12 - mA Output Levels: Reduced drive option (38, 39) High Current (VOUT = VCCQ - 0.763V, minimum VREF, minimum VTT) Low Current (VOUT = 0.763V, maximum VREF, maximum VTT) IOHR -9 - mA IOLR 9 - mA I/O Reference Voltage (6,44) VREF 0.49 x VCCQ 0.51 x VCCQ V I/O Termination Voltage (7, 44) VTT VREF - 0.04 VREF + 0.04 V Symbol Min Max Units Input High (Logic 1) Voltage VIH VREF +0.310 -- V Input Low (Logic 0) Voltage VIL -- VREF -0.310 V AC INPUT OPERATING CONDITIONS VCC, VCCQ = +2.5V 0.2V; -55C TA +125C Parameter/Condition Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 10 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX ICC SPECIFICATIONS AND CONDITIONS (NOTES 1-5, 10, 12, 14, 46, 54) VCC, VCCQ = +2.5V 0.2V; -55C TA +125C MAX Symbol 250MHz 266MHz 200MHz Units OPERATING CURRENT: One bank; Active-Precharge; tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs changing once per clock cyle; Address and control inputs changing once every two clock cycles; (22, 47) ICC0 650 575 mA OPERATING CURRENT: One bank; Active-Read-Precharge; Burst = 2; tRC = tRC (MIN); tCK = tCK (MIN); IOUT = 0mA; Address and control inputs changing once per clock cycle (22, 47) ICC1 800 725 mA PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; Power-down mode; tCK = tCK (MIN); CKE = LOW; (23, 32, 49) ICC2P 25 25 mA IDLE STANDBY CURRENT: CS = HIGH; All banks idle; tCK = tCK (MIN); CKE = HIGH; Address and other control inputs changing once per clock cycle. VIN = VREF for DQ, DQS, and DM (50) ICC2F 225 200 mA ACTIVE POWER-DOWN STANDBY CURRENT: One bank active; Power-down mode; tCK = tCK (MIN); CKE = LOW (23, 32, 49) ICC3P 175 150 mA ACTIVE STANDBY CURRENT: CS = HIGH; CKE = HIGH; One bank; Active-Precharge; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle (22) ICC3N 250 225 mA OPERATING CURRENT: Burst = 2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK (MIN); IOUT = 0mA (22, 47) ICC4R 825 725 mA OPERATING CURRENT: Burst = 2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per clock cycle (22) ICC4W 755 675 mA tREFC = tRC (MIN) (49) ICC5 1,450 1,400 mA tREFC = 7.8125s (27, 49) ICC5A 50 50 mA Parameter/Condition AUTO REFRESH CURRENT SELF REFRESH CURRENT: CKE 0.2V Standard (11) OPERATING CURRENT: Four bank interleaving READs (BL=4) with auto precharge, tRC =tRC (MIN); tCK = tCK (MIN); Address and control inputs change only during Active READ or WRITE commands. (22, 48) ICC6 25 25 mA ICC7 2,000 1,750 mA Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 11 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CHARACTERISTICS Notes 1-5, 14-17, 33 266 MHz CL 2.5 200 CL 2 Parameter 250 MHz CL2.5 200 MHz CL2 200 MHz CL2.5 150 MHz CL2 Symbol Min Max Min Max Min Max Access window of DQs from CK/CK# tAC -0.75 +0.75 -0.8 +0.8 -0.8 +0.8 ns CK high-level width (30) tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK CK low-level width (30) Units tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK CL = 2.5 (45, 51) tCK (2.5) 7.5 13 8 13 10 13 ns CL = 2 (45, 51) tCK (2) 10 13 10 13 13 15 ns DQ and DM input hold time relative to DQS (26, 31) tDH 0.5 0.6 0.6 ns DQ and DM input setup time relative to DQS (26, 31) tDS 0.5 0.6 0.6 ns DQ and DM input pulse width (for each input) (31) tDIPW 1.75 2 2 Access window of DQS from CK/CK# tDQSCK -0.75 Clock cycle time +0.75 -0.8 +0.8 ns -0.8 +0.8 ns DQS input high pulse width tDQSH 0.35 0.35 0.35 DQS input low pulse width tDQSL 0.35 0.35 0.35 DQS-DQ skew, DQS to last DQ valid, per group, per access (25, 26) tDQSQ Write command to first DQS latching transition tDQSS 0.75 DQS falling edge to CK rising - setup time tDSS 0.2 0.2 0.2 tCK DQS falling edge from CK rising - hold time tDSH 0.2 0.2 0.2 tCK Half clock period (34) tHP tCH,tCL tCH,tCL tCH,tCL Data-out high-impedance window from CK/CK# (18, 42) tHZ 0.5 1.25 tCK tCK 0.6 0.75 1.25 +0.75 0.75 0.6 ns 1.25 tCK ns +0.8 +0.8 ns Data-out low-impedance window from CK/CK# (18, 42) tLZ -0.75 -0.8 -0.8 ns Address and control input hold time (fast slew rate) tIHF 0.90 1.1 1.1 ns Address and control input setup time (fast slew rate) tISF 0.90 1.1 1.1 ns Address and control input hold time (slow slew rate) (14) tIHS 1 1.1 1.1 ns Address and control input setup time (slow slew rate) (14) tISS 1 1.1 1.1 ns LOAD MODE REGISTER command cycle time tMRD 15 16 16 ns DQ-DQS hold, DQS to first DQ to go non-valid, per access (25, 26) tQH tHP-tQHS tHP-tQHS tHP-tQHS Data hold skew factor tQHS ACTIVE to PRECHARGE command (35) tRAS 40 ACTIVE to READ with Auto precharge command tRAP 20 20 20 ns ACTIVE to ACTIVE/AUTO REFRESH command period tRC 65 70 70 ns AUTO REFRESH command period (49) tRFC 75 80 80 ns ACTIVE to READ or WRITE delay tRCD 20 20 20 ns PRECHARGE command period tRP 20 20 20 DQS read preamble (43) tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 tCK DQS read postamble (43) tRPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK ACTIVE bank a to ACTIVE bank b command tRRD 15 15 15 ns DQS write preamble tWPRE 0.25 0.25 0.25 tCK DQS write preamble setup time (20, 21) tWPRES 0 DQS write postamble (19) tWPST 0.4 Write recovery time tWR 15 15 15 ns Internal WRITE to READ command delay tWTR 1 1 1 tCK Data valid output window (25) 0.75 na REFRESH to REFRESH command interval (23) (Commercial & Industrial only) tREFC 120,000 40 120,000 0 0.6 ns 1 0.6 120,000 ns ns ns 0.4 tQH - tDQSQ 70.3 ns 0 0.4 tQH - tDQSQ 40 1 0.6 tQH - tDQSQ tCK ns 70.3 70.3 s REFRESH to REFRESH command interval (23) (Military temperature only)* tREFC 35 35 35.15 s Average periodic refresh interval (23) (Commercial & Industrial only) tREFI 7.8 7.8 7.8 s Average periodic refresh interval (23) (Military temperature only)* tREFI 3.9 3.9 3.9 s Terminating voltage delay to VCC (53) tVTD 0 0 0 ns Exit SELF REFRESH to non-READ command tXSNR 75 80 80 ns Exit SELF REFRESH to READ command tXSRD 200 200 200 tCK * Self refresh available in commercial and industrial temperatures only. Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 12 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX NOTES: 1. All voltages referenced to VSS. 2. Tests for AC timing, ICC, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. 3. Outputs measured with equivalent load: 17. The output timing reference level, as measured at the timing reference point indicated in Note 3, is VTT. 18. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving (HZ) or begins driving (LZ). 19. The intent of the Don't Care state after completion of the postamble is the DQS-driven signal should either be high, low, or high-Z and that any signal transition within the input switching region must follow valid input requirements. That is, if DQS transitions high (above VIHDC(MIN) then it must not transition low (below VIHDC) prior to tDQSH(MIN). 20. This is not a device limit. The device will operate with a negative value, but system performance could be degraded due to bus turnaround. 21. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command. The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were previously in progress on the bus. If a previous WRITE was in progress, DQS could be HIGH during this time, depending on tDQSS. 22. MIN (tRC or tRFC) for ICC measurements is the smallest multiple of tCK that meets the minimum absolute value for the respective parameter. tRAS (MAX) for ICC measurements is the largest multiple of tCK that meets the maximum absolute value for tRAS. 23. The refresh period 64ms. (32ms for Military grade) This equates to an average refresh rate of 7.8125s. However, an AUTO REFRESH command must be asserted at least once every 70.3s; (35s for Military grade) burst refreshing or posting by the DRAM controller greater than eight refresh cycles is not allowed. 24. The I/O capacitance per DQS and DQ byte/group will not differ by more than this maximum amount for any given device. 25. The valid data window is derived by achieving other specifications - tHP (tCK/2), tDQSQ, and tQH (tQH = tHP - tQHS). The data valid window derates directly porportional with the clock duty cycle and a practical data valid window can be derived. The clock is allowed a maximum duty cycle variation of 45/55. Functionality is uncertain when operating beyond a 45/55 ratio. The data valid window derating curves are provided below for duty cycles ranging between 50/50 and 45/55. 26. Referenced to each output group: DQSL with DQ0-DQ7; and DQSH with DQ8-DQ15 of each chip. 27. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during standby). 28. To maintain a valid level, the transitioning edge of the input must: a) Sustain a constant slew rate from the current AC level through to the target AC level, VIL(AC) or VIH(AC). b) Reach at least the target AC level. c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC). 29. The Input capacitance per pin group will not differ by more than this maximum amount for any given device. 30. CK and CK# input slew rate must be 1V/ns (2V/ns differentially). 31. DQ and DM input slew rates must not deviate from DQS by more than 10%. If the DQ/DM/DQS slew rate is less than 0.5V/ns, timing must be derated: 50ps must be added to tDS and tDH for each 100mV/ns reduction in slew rate. If slew rate exceeds 4V/ns, functionality is uncertain. 32. VCC must not vary more than 4% if CKE is not active while any bank is active. 33. The clock is allowed up to 150ps of jitter. Each timing parameter is allowed to vary by the same amount. VTT 50 Reference Point 30pF Output (VOUT) 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. AC timing and ICC tests may use a VIL-to-VIH swing of up to 1.5V in the test environment, but input timing is still referenced to VREF (or to the crossing point for CK/CK#), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions. The minimum slew rate for the input signals used to test the device is 1V/ns in the range between VIL(AC) and VIH(AC). The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result of the signal crossing the AC input level, and will remain in that state as long as the signal does not ring back above [below] the DC input LOW [HIGH] level). VREF is expected to equal VCCQ/2 of the transmitting device and to track variations in the DC level of the same. Peak-to-peak noise (noncommon mode) on VREF may not exceed 2 percent of the DC value. Thus, from VCCQ/2, VREF is allowed 25mV for DC error and an additional 25mV for AC noise. This measurement is to be taken at the nearest VREF by-pass capacitor. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF and must track variations in the DC level of VREF. VID is the magnitude of the difference between the input level on CK and the input level on CK#. The value of VIX and VMP are expected to equal VCCQ/2 of the transmitting device and must track variations in the DC level of the same. ICC is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle time with the outputs open. Enables on-chip refresh and address counters. ICC specifications are tested after the device is properly initialized, and is averaged at the defined cycle rate. This parameter is not tested but guaranteed by design. tA = 25C, F= 1 MHz For slew rates less than 1V/ns and greater than or equal to 0.5 V.ns. If the slew rate is less than 0.5V/ns, timing must be derated: tIS has an additional 50 ps per each 100mV/ns reduction in slew rate from the 500mV/ns. tIH has 0ps added, that is, it remains constant. If the slew rate exceeds 4.5V/ns, functionality is uncertain. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at which CK# and CK# cross; the input reference level for signals other than CK/CK# is VREF. Inputs are not recognized as valid until VREF stabilizes. Once initialized, including SELF REFRESH mode, VREF must be powered within specified range. Exception: during the period before VREF stabilizes, CKE 0.3 x VCCQ is recognized as LOW. FIGURE A - FULL DRIVE PULL-DOWN CHARACTERISTICS FIGURE B - FULL DRIVE PULL-UP CHARACTERISTICS 0 160 Maximum 140 -20 Minimum -40 120 IOUT (mA) IOUT (mA) Nominal low -60 Nominal high 100 80 Nominal low 60 Minimum -80 -100 Nominal high -120 -140 40 -160 20 -180 0 Maximum -200 0.0 0.5 1.0 1.5 2.0 2.5 0.0 0.5 1.0 1.5 2.0 2.5 VCCQ - VOUT (V) VOUT (V) Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 13 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX 34. tHP min is the lesser of tCL minimum and tCH minimum actually applied to the device CK and CK# inputs, collectively during bank active. 35. READs and WRITEs with auto precharge are not allowed to be issued until tRAS(MIN) can be satisfied prior to the internal precharge command being issued. 36. Any positive glitch must be less than 1/3 of the clock and not more than +400mV or 2.9 volts, whichever is less. Any negative glitch must be less than 1/3 of the clock cycle and not exceed either -300mV or 2.2 volts, whichever is more positive. The average cannot be below the 2.5V minimum. 37. Normal Output Drive Curves: a) The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure A. b) The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure A. c) The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure B. d) The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure B. e) The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between .71 and 1.4, for device drain-to-source voltages from 0.1V to 1.0 Volt, and at the same voltage and temperature. f) The full variation in the ratio of the nominal pull-up to pull-down current should be unity 10%, for device drain-to-source voltages from 0.1V to 1.0 Volt. 38. Reduced Output Drive Curves: a) The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure C. b) The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure C. c) The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure D. d) The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure D. e) The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between .71 and 1.4, for device drain-to-source voltages from 0.1V to 1.0 V, and at the same voltage and temperature. f) The full variation in the ratio of the nominal pull-up to pull-down current should be unity 10%, for device drain-to-source voltages from 0.1V to 1.0 V. 39. The voltage levels used are derived from a minimum VCC level and the referenced test load. In practice, the voltage levels obtained from a properly terminated bus will provide significantly different voltage values. 40. VIH overshoot: VIH(MAX) = VCCQ+1.5V for a pulse width 3ns and the pulse width can not be greater than 1/3 of the cycle rate. VIL undershoot: VIL (MIN) = -1.5V for a pulse width 3ns and the pulse width cannot be greater than 1/3 of the cycle rate. 41. VCC and VCCQ must track each other. 42. tHZ (MAX) will prevail over tDQSCK (MAX) + tRPST (MAX) condition. tLZ (MIN) will prevail over tDQSCK (MIN) + tRPRE (MAX) condition. 43. tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). 44. During initialization, VCCQ, VTT, and VREF must be equal to or less than VCC + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even if VCC/VCCQ are 0 volts, provided a minimum of 42 ohms of series resistance is used between the VTT supply and the input pin. 45. The current part operates below the slowest JEDEC operating frequency of 83 MHz. As such, future die may not reflect this option. 46. When an input signal is HIGH or LOW, it is defined as a steady state logic HIGH or LOW. 47. Random addressing changing: 50% of data changing at every transfer. 48. Random addressing changing: 100% of data changing at every transfer. 49. CKE must be active (high) during the entire time a refresh command is executed. That is, from the time the AUTO REFRESH command is registered, CKE must be active at each rising clock edge, until tRFC has been satisfied. 50. ICC2N specifies the DQ, DQS, and DQM to be driven to a valid high or low logic level. ICC2Q is similar to ICC2F except ICC2Q specifies the address and control inputs to remain stable. Although ICC2F, ICC2N, and ICC2Q are similar, ICC2F is "worst case." 51. Whenever the operating frequency is altered, not including jitter, the DLL is required to be reset followed by 200 clock cycles before any READ command. 52. This is the DC voltage supplied at the DRAM and is inclusive of all noise up to 20 MHz. Any noise above 20 MHz at the DRAM generated from any source other than that of the DRAM itself may not exceed the DC coltage range of 2.6V 100mV. 53. All AC timings do not count extra clock needed on address and control signals to be registered. 54. DDR currents only. Register currents not included. FIGURE C - REDUCED DRIVE PULL-DOWN CHARACTERISTICS FIGURE D - REDUCED DRIVE PULL-UP CHARACTERISTICS 0 80 Maximum -10 70 60 Nominal high 40 IOUT (mA) IOUT (mA) 50 Nominal low 30 -20 Minimum -30 Nominal low -40 -50 Minimum Nominal high 20 -60 10 -70 0 -80 Maximum 0.0 0.5 1.0 1.5 2.0 0.0 2.5 0.5 1.0 1.5 2.0 2.5 VCCQ - VOUT (V) VOUT (V) Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 14 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX PACKAGE DIMENSION: 208 PLASTIC BALL GRID ARRAY (PBGA) Bottom View 208 x O 0.60 (0.024) NOM 11 10 9 8 7 6 5 4 3 2 1 A B C D E 18.0 (0.709) NOM G H J K L M 1.0 (0.039) NOM 25.1 (0.988) MAX F N P R T U V W 1.0 (0.039) NOM 0.50 (0.020) NOM 10.0 (0.394) NOM 3.20 (0.126) MAX 16.1 (0.634) MAX NOTE: This package utilizes solder balls which contain lead. Sn63Pb37; if you require a lead-free solder ball package please contact Microsemi for information. All linear dimensions are millimeters and parenthetically in inches Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 15 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX ORDERING INFORMATION W 3E 32M 72 S R - XXX SB X MICROSEMI CORPORATION DDR SDRAM CONFIGURATION, 32M x 72 2.5V Power Supply R = Registered DATA RATE (MHz) 200 = 200MHz 250 = 250MHz 266 = 266MHz PACKAGE: (1) SB = 208 Plastic Ball Grid Array (PBGA) DEVICE GRADE: M = Military I = Industrial C = Commercial -55C to +125C -40C to +85C 0C to +70C Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 16 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com W3E32M72SR-XSBX Document Title 32M x 72 Registered DDR SDRAM, 208 PBGA Multi-Chip Package, 16mm x 25mm Revision History Rev # History Release Date Status Rev 0 Initial Release July 2004 Advanced Rev 1 Changes (Pg. 1, 2, 3, 17, 18, 19) May 2005 Advanced April 2006 Final July 2006 Final 1.1 Change pkg to 16mm x 25mm 208 PBGA Rev 2 Changes (Pg. All) 2.1 Change status to Final Rev 3 Changes (Pg. 1, 10, 11, 17, 19) 3.1 Add thermal resistance data 3.2 Add lead solder ball note Microsemi Corporation reserves the right to change products or specifications without notice. July 2006 Rev. 3 (c) 2010 Microsemi Corporation. All rights reserved. 17 Microsemi Corporation * (602) 437-1520 * www.whiteedc.com www.microsemi.com