WIZ610WI - WIZnet - Datasheet.Live

WIZ610WI 사용자 매뉴얼 (WIZnet, Inc.)

WIZ610WI Quick Installation Guide

(Version 1.0)

☞ For more information, please visit our website at http://www.wiznet.co.kr

WIZ610WI 사용자 매뉴얼 (WIZnet, Inc.)

ii

WIZnet’s Online Technical Support

If you have any questions about our products, please visit our website and post your questions

on the Q&A Board. We will reply your questions as soon as possible

C

CL

LI

IC

CK

K

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

COPYRIGHT NOTICE

Technical Support: support@wiznet.co.kr

Sales & Distribution: sales@wiznet.co.kr

For more information, visit our website at http://www.wiznet.co.kr

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

1. Hardware Setting

Step 1.Connecting Ethernet Cable

Connect WIZ610Wi evaluation board to PC by using the UTP Cable.

You can use any types of UTP cable (direct or crossover cable).

Step 2.Connecting Serial Cable

Connect WIZ610Wi evaluation board to your PC by using the DB9 female serial cable.

Step 3.Connecting Wireless LAN Antenna

Connect the wireless LAN antenna to the U.FL antenna connector of WIZ610wi.

The antenna should have pigtail.

2. Software Setting

2-1. The Configurations WEB Page

Step 1.Setting up the IP address of the PC

The default IP address and Subnet Mask of WIZ610Wi are 192.168.1.254 and

255.255.255.0 Please configure the IP address of your PC as 192.168.1.XXX and

Subnet Mask as 255.255.255.0.

Step 2.Connecting Configuration Page

Open the web browser on your PC and input the IP address as “192.168.1.254” to

connect to the configuration page. Please enter the ID and Password

(Default ID: admin/ Password: admin)

2-2. Network Setting

To establish a Wi-Fi communication, the devices in the same network must have same values in

the parameters of IP address level, SSID, Channel, Encryption. For the detail, refer to below

figure. If you setup WIZ610wi as Static IP, you have to know IP address level of Access Point.

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

Step 1.Wired Network Setting

Please set your IP address, Subnet Mask and Gateway of your WIZ610Wi. The default

IP address is “192.168.1.254”.

Step 2. DHCP Settings

Select if you use DHCP function or not, and configure the ‘DHCP Client Range’.

When WIZ610Wi is set as DHCP server, it operates as below according to the

operation mode.

 Access Point Mode : If there is another DHCP server operating at the upper level in

the network, it assigns IP address to the client, but does not to WIZ610Wi. If there is

not any other DHCP server, WIZ610Wi assigns IP address.

 Gateway Mode : In this mode, WIZ610Wi is a bridge for Ethernet to the MII interface.

Regardless of DHCP server operating at the upper level, WIZ610Wi assigns IP

address to the client.

 Client Mode : If WIZ610Wi is set as Client mode, it does not operate as DHCP Client.

The application board directly acquires IP address from DHCP server.

2-3. Wireless Setting

Step 1. Please configure the operation mode of WIZ610Wi. You can select one of modes

(Access Point, Gateway, and Client)

Step 2. Please setup the following parameters: SSID / Channel Number/ Data Rate / Security /

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

Access Control / Advanced

/ WDS Setting

 SSID: SSID should be configured for the wireless communication. The default SSID

is “WIZ610Wi”. You can rename your SSID to a name of your choice

 Channel: A different channel should be selected when your device experienced

interferences from other wireless network. The default channel is set as “1”.

 Security : The default security setting is set as “Open System or Shared Key/NONE

Encryption”.

 Access Control : The default Access Control is “Disable”.

 WDS : The default WDS is set as “AP” mode

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

2-4. Serial-Wireless Configuration

Step 1. Serial Parameter Setting

Enable the status of “Serial to Wireless LAN” configuration

Input the serial parameters to communicate with the serial device.

 Protocol: Select UDP or TCP

 Mode : Select a mode (Server, Client, Mixed)

 Server IP/Port : At the Client or Mixed mode, you should set the server IP address.

WIZ610Wi will try to connect to this server IP address.

 Configure Baud rate, Databits, Parity, Stopbits, Flow Control.

2-5. Testing

Step 1. Serial to Wireless Gateway Test

 Open a terminal program of your choice on your PC (ex: Hyper Terminal). Please set the

same baud rate as the WIZ610Wi.

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

Connect to “WIZ610Wi” in the Wireless Network Setting of your PC

 Open another Terminal program and input IP address and Port Number of WIZ610Wi.

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

 Input any characters in the Hyper Terminal for Serial. (In the example below,

“01234567890” is input). The same characters are outputted in the Hyper Terminal for

Network. A Serial to Wireless LAN test was performed.

Received Data by Network Terminal Program

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

A serial to Ethernet test can also be performed by using the hyper terminal.

In the same way, input any character in the screen of terminal program for network, and check if

same character is displayed in the screen for serial (Ethernet to Serial)

※ The above test can also be performed in a program called, “Device Terminal program”, which is easy

and simple to use.

Device Terminal Program

Device Terminal is a program which integrates both serial and network communications into one user

interface so that you can test your WIZnet gateway module easily.

As shown in above Figure, the upper part of the program allows you to configure your serial setting of

WIZ610Wi. By clicking the “Open” button, serial communication is enabled.

The lower part of the program allows you to configure the network settings. You can test both TCP Client

and TCP Server modes at the same time. If the Server Mode is enabled, Device Terminal will operate as

server mode, and the WIZ610Wi module will work as client mode. The PC where the Device Terminal is

operating will work as a server, the IP address of the PC should be set as Server IP of the module. If

Server mode is not checked, Device Terminal will operate as client mode, and the module as server. For

the IP address and port, please input your IP address and port number of WIZ610Wi and click the

“Connect” button to start a network communication.

WIZ610WI Quick Installation Guide (WIZnet, Inc.)

When serial and network terminals are connected, input any character in the Data Input window and click

“Send” button. You can check the data is transferred into the another window.