Data Sheet, Rev. 1.0, Mar. 2004 HYS72D32300GBR-[5/6]-C HYS72D64300GBR-[5/6]-C HYS72D64320GBR-[5/6]-C HYS72D128320GBR-6-C 184-Pin Registered Double Data Rate SDRAM Module Reg DIMM DDR SDRAM Memory Products N e v e r s t o p t h i n k i n g . Edition 2004-03 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 Munchen, Germany (c) Infineon Technologies AG 2004. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Data Sheet, Rev. 1.0, Mar. 2004 HYS72D32300GBR-[5/6]-C HYS72D64300GBR-[5/6]-C HYS72D64320GBR-[5/6]-C HYS72D128320GBR-6-C 184-Pin Registered Double Data Rate SDRAM Module Reg DIMM DDR SDRAM Memory Products N e v e r s t o p t h i n k i n g . HYS72D32300GBR-[5/6]-C HYS72D64300GBR-[5/6]-C HYS72D64320GBR-[5/6]-C HYS72D128320GBR- 6-CHYS72D64300GBR-[5/6]-C HYS72D64320GBR-[5/6]-C Revision History: Rev. 1.0 Previous Version: Rev. 0.5 Page Subjects (major changes since last revision) 20,21 Idd values updated 8,22 editorial changes 24,27 Changed SPD Code Byte 99 - 127 to FF 2004-03 We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc.mp@infineon.com Template: mp_a4_v2.2_2003-10-07.fm HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Table of Contents 1 1.1 1.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 3.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4 4.1 Current Specification and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5 SPD Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7 Application Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Data Sheet 5 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Overview 1 Overview 1.1 Features * * * * * * * * * * * * 184-Pin Registered 8-Byte Dual-In-Line DDR SDRAM Module for "1U" PC, Workstation and Server main memory applications One rank 32 M x 72 and 64M x 72 and two ranks 64 M x72 and 128 M x72 organization JEDEC standard Double Data Rate Synchronous DRAMs (DDR SDRAM) with a single + 2.5 V ( 0.2 V) power supply and + 2.6 V ( 0.1 V) power supply for DDR400 Built with 256-Mbit DDR SDRAMs in P-TFBGA-60-1 packages Programmable CAS Latency, Burst Length, and Wrap Sequence (Sequential & Interleave) Auto Refresh (CBR) and Self Refresh All inputs and outputs SSTL_2 compatible Re-drive for all input signals using register and PLL devices. Serial Presence Detect with E2PROM Low Profile Modules form factor: 133.35 mm x 28.58 mm x 4.00 mm / 2.64 mm and for 1GB 133.35 mm x 30.48 mm (1.2")x 4.00 mm JEDEC standard reference layout for one rank 256 MB, 512 MB and two ranks 512 MB, 1 GB: PC2700 and PC3200 Registered DIMM Raw Cards A,B,C,D Gold plated contacts Table 1 Performance Part Number Speed Code Speed Grade max. Clock Frequency -5 -6 Unit Component DDR400B DDR333B -- Module PC3200-3033 PC2700-2533 -- 200 166 MHz 166 166 MHz 133 133 MHz @CL3 @CL2.5 @CL2 1.2 fCK3 fCK2.5 fCK2 Description The HYS72D[128/64/32][300/320]GBR-[5/6]-C and HYS72D64320GBR-5-C are low profile versions of the standard Registered DIMM modules suitable for 1U Server Applications. The Low Profile DIMM versions are available as 32 M x72 (256 MB), 64 M x72 (512 MB) and 128 M x72 (1 GB) The memory array is designed with Double Data Rate Synchronous DRAMs for ECC applications. All control and address signals are re-driven on the DIMM using register devices and a PLL for the clock distribution. This reduces capacitive loading to the system bus, but adds one cycle to the SDRAM timing. A variety of decoupling capacitors are mounted on the PC board. The DIMMs feature serial presence detect based on a serial E2PROM device using the 2-pin I2C protocol. The first 128 bytes are programmed with configuration data and the second 128 bytes are available to the customer. Data Sheet 6 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Overview Table 2 Ordering Information Type Compliance Code Description SDRAM Technology PC3200 (CL = 3.0) HYS72D32300GBR-5-C PC3200R-30330-A0 1 Rank 256 MB Registered DIMM ECC 256 Mbit (x8) HYS72D64300GBR-5-C PC3200R-30330-C0 1 Rank 512 MB Registered DIMM ECC 256 Mbit (x4) HYS72D64320GBR-5-C PC3200R-30330-B0 2 Ranks 512 MB Registered DIMM ECC 256 Mbit (x8) PC2700 (CL = 2.5, tRP = tRCD = 3 at tCK = 6ns) HYS72D32300GBR-6-C PC2700R-25330-A0 1 Rank 256 MB Registered DIMM ECC 256 Mbit (x8) HYS72D64300GBR-6-C PC2700R-25330-C0 1 Rank 512 MB Registered DIMM ECC 256 Mbit (x4) HYS72D64320GBR-6-C PC2700R-25330-B0 2 Ranks 512 MB Registered DIMM ECC 256 Mbit (x8) HYS72D128320GBR-6-C PC2700R-25330-D0 2 Ranks 1 GB Registered DIMM ECC Data Sheet 7 256 Mbit (x4) Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration 2 Pin Configuration Table 3 The pin configuration of the Registered DDR SDRAM DIMM is listed by function in Table 3 (184 pins). The abbreviations used in columns Pin and Buffer Type are explained in Table 4 and Table 5 respectively. The pin numbering is depicted in Figure 1. Table 3 Pin# Name Pin Configuration of RDIMM (cont'd) Pin Buffer Function Type Type 125 A6 I SSTL 29 A7 I SSTL Pin Configuration of RDIMM 122 A8 I SSTL Pin Buffer Function Type Type 27 A9 I SSTL 141 A10 I SSTL AP I SSTL Pin# Name Clock Signals 137 CK0 I SSTL Clock Signal 118 A11 I SSTL 138 CK0 I SSTL Complement Clock 115 A12 I SSTL 21 CKE0 I SSTL Clock Enable Rank 0 111 CKE1 I SSTL Clock Enable Rank 1 NC NC SSTL Note: 1-rank module Control Signals S0 I SSTL Chip Select of Rank 0 158 S1 I SSTL Chip Select of Rank 1 167 NC - Note: 1-rank module 154 RAS I SSTL Row Address Strobe 65 CAS I SSTL Column Address Strobe 63 WE I SSTL Write Enable 10 RESET I NC NC - Note: 128 Mbit module A13 I SSTL Address Signal 13 Note: 1 Gbit module Note: 2-ranks module NC Address Signal 12 Note: Module based on 256 Mbit or larger dies Note: 2-rank module 157 Address Bus 11:0 NC NC - based based Note: Module based on 512 Mbit or smaller dies LVRegister Reset CMOS Forces registered inputs low Note: For detailed description of the Power Up and Power Management see the Application Note at the end of data sheet Address Signals 59 BA0 52 BA1 I SSTL Bank Address Bus 1:0 48 A0 I SSTL Address Bus 11:0 43 A1 I SSTL 41 A2 I SSTL 130 A3 I SSTL 37 A4 I SSTL 32 A5 I SSTL Data Sheet I SSTL Address Bus 11:0 8 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration Table 3 Table 3 Pin Configuration of RDIMM (cont'd) Pin# Name Pin Buffer Function Type Type Data Signals Data Bus 63:0 Pin Configuration of RDIMM (cont'd) Pin# Name Pin Buffer Function Type Type 150 DQ38 I/O SSTL 151 DQ39 I/O SSTL 2 DQ0 I/O SSTL 4 DQ1 I/O SSTL 61 DQ40 I/O SSTL 6 DQ2 I/O SSTL 64 DQ41 I/O SSTL Data Bus 63:0 8 DQ3 I/O SSTL 68 DQ42 I/O SSTL 94 DQ4 I/O SSTL 69 DQ43 I/O SSTL 95 DQ5 I/O SSTL 153 DQ44 I/O SSTL 98 DQ6 I/O SSTL 155 DQ45 I/O SSTL 99 DQ7 I/O SSTL 161 DQ46 I/O SSTL 12 DQ8 I/O SSTL 162 DQ47 I/O SSTL 13 DQ9 I/O SSTL 72 DQ48 I/O SSTL 19 DQ10 I/O SSTL 73 DQ49 I/O SSTL 20 DQ11 I/O SSTL 79 DQ50 I/O SSTL 105 DQ12 I/O SSTL 80 DQ51 I/O SSTL 106 DQ13 I/O SSTL 165 DQ52 I/O SSTL 109 DQ14 I/O SSTL 166 DQ53 I/O SSTL 110 DQ15 I/O SSTL 170 DQ54 I/O SSTL 23 DQ16 I/O SSTL 171 DQ55 I/O SSTL 24 DQ17 I/O SSTL 83 DQ56 I/O SSTL 28 DQ18 I/O SSTL 84 DQ57 I/O SSTL 31 DQ19 I/O SSTL 87 DQ58 I/O SSTL 114 DQ20 I/O SSTL 88 DQ59 I/O SSTL 117 DQ21 I/O SSTL 174 DQ60 I/O SSTL 121 DQ22 I/O SSTL 175 DQ61 I/O SSTL 123 DQ23 I/O SSTL 178 DQ62 I/O SSTL 33 DQ24 I/O SSTL 179 DQ63 I/O SSTL 35 DQ25 I/O SSTL 44 CB0 I/O SSTL 39 DQ26 I/O SSTL 45 CB1 I/O SSTL 40 DQ27 I/O SSTL 49 CB2 I/O SSTL 126 DQ28 I/O SSTL 51 CB3 I/O SSTL 127 DQ29 I/O SSTL 134 CB4 I/O SSTL 131 DQ30 I/O SSTL 135 CB5 I/O SSTL 133 DQ31 I/O SSTL 142 CB6 I/O SSTL 53 DQ32 I/O SSTL 144 CB7 I/O SSTL 55 DQ33 I/O SSTL 5 DQS0 I/O SSTL Data Strobes 8:0 57 DQ34 I/O SSTL 14 DQS1 I/O SSTL 60 DQ35 I/O SSTL 25 DQS2 I/O SSTL 146 DQ36 I/O SSTL 36 DQS3 I/O SSTL Note: See block diagram for corresponding DQ signals 147 DQ37 I/O SSTL 56 DQS4 I/O SSTL 67 DQS5 I/O SSTL Data Sheet 9 Check Bits 7:0 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration Table 3 Table 3 Pin Configuration of RDIMM (cont'd) Pin Configuration of RDIMM (cont'd) Pin# Name Pin Buffer Function Type Type Pin# Name 78 DQS6 I/O SSTL EEPROM 86 DQS7 I/O SSTL 92 SCL I CMOS Serial Bus Clock 47 DQS8 I/O SSTL 91 SDA I/O OD 97 DM0 I SSTL Data Mask 0 181 SA0 I Note: x8 based module 182 SA1 I CMOS Slave Address Select CMOS Bus 2:0 Data Strobe 9 183 SA2 I CMOS Note: x4 based module Power Supplies Data Mask 1 1 Note: x8 based module 184 DQS9 107 DM1 I/O I DQS10 I/O SSTL SSTL SSTL Data Strobes 8:0 DM2 I SSTL Data Mask 2 Note: x8 based module DQS11 I/O SSTL Data Strobe 11 DM3 SSTL Data Mask 3 Note: x4 based module 129 I Note: x8 based module DQS12 I/O SSTL Data Strobe 12 Note: x4 based module 149 DM4 I SSTL Data Mask 4 Note: x8 based module DQS13 I/O SSTL Data Strobe 13 Note: x4 based module 159 DM5 I SSTL Data Mask 5 Note: x8 based module DQS14 I/O SSTL Data Strobe 14 Note: x4 based module 169 DM6 I SSTL VREF AI - VDDSPD PWR - Data Strobe 10 Note: x4 based module 119 Pin Buffer Function Type Type Data Mask 6 Note: x8 based module DQS15 I/O SSTL Data Strobe 15 DM7 SSTL Data Mask 7 Serial Bus Data I/O Reference Voltage EEPROM Power Supply 15, VDDQ 22, 30, 54, 62, 77, 96, 104, 112, 128, 136, 143, 156, 164, 172, 180 PWR - I/O Driver Power Supply VDD 7, 38, 46, 70, 85, 108, 120, 148, 168 PWR - Power Supply Note: x4 based module 177 I Note: x8 based module DQS16 I/O SSTL Data Strobe 16 Note: x4 based module 140 DM8 I SSTL Data Mask 8 Note: x8 based module DQS17 I/O SSTL Data Strobe 17 Note: x4 based module Data Sheet 10 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration Table 3 Pin Configuration of RDIMM (cont'd) Pin# Name Pin Buffer Function Type Type VSS 3, 11, 18, 26, 34, 42, 50, 58, 66, 74, 81, 89, 93, 100, 116, 124, 132, 139, 145, 152, 160, 176 GND - Table 4 Abbreviations for Pin Type Abbreviation Description Ground Plane I Standard input-only pin. Digital levels. O Output. Digital levels. I/O I/O is a bidirectional input/output signal. AI Input. Analog levels. PWR Power GND Ground NU Not Usable (JEDEC Standard) NC Not Connected (JEDEC Standard) Table 5 Abbreviations for Buffer Type Abbreviation Description SSTL Serial Stub Terminalted Logic (SSTL2) LV-CMOS Low Voltage CMOS CMOS CMOS Levels OD Open Drain. The corresponding pin has 2 operational states, active low and tristate, and allows multiple devices to share as a wire-OR. Other Pins 82 VDDID O OD VDD Identification Note: Pin in tristate, indicating VDD and VDDQ nets connected on PCB NC 9, 16, 17, 71, 75, 76, 90, 101, 102, 103, 113, 163, 173 Data Sheet NC - Not connected Pins not connected on Infineon RDIMM's 11 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration A2 CB01 CB02 DQ32 DQ34 DQ40 CAS DQ43 DQ49 VDDQ VSS VDD VSS VSS DM00/DQS9 NC DQ12 DQ14 NC DQ21 DQ22 A6 DM3/DQS12 DQ31 CK0 A10/AP VSS DM4/DQS13 DQ44 S0 DQ46 DQ52 DM6/DQS15 NC DM7/DQS16 SA0 - Pin 041 Pin 045 Pin 049 Pin 053 Pin 057 Pin 061 Pin 065 Pin 069 Pin 073 Pin 077 Pin 081 Pin 085 Pin 089 Pin 093 Pin 097 Pin 101 Pin 105 Pin 109 Pin 113 Pin 117 Pin 121 Pin 125 Pin 129 Pin 133 Pin 137 Pin 141 Pin 145 Pin 149 Pin 153 Pin 157 Pin 161 Pin 165 Pin 169 Pin 173 Pin 177 Pin 181 VSS VDD VSS VDDQ - - DQ01 - DQ03 - DQ08 - NC - DQ11 - DQ17 - DQ18 - A5 - DQS3 - DQ27 DQ10 DQ16 A9 DQ19 DQ25 DQ26 - Pin 003 Pin 007 Pin 011 Pin 015 Pin 019 Pin 023 Pin 027 Pin 031 Pin 035 Pin 039 Pin 004 Pin 008 Pin 012 Pin 016 Pin 020 Pin 024 Pin 028 Pin 032 Pin 036 Pin 040 A1 DQS8 CB03 DQ33 BA0 WE DQS5 NC NC DQ50 DQ56 DQ58 SDA DQ05 DQ07 NC DM1/DQS10 CKE1/NC A12/NC DM2/DQS11 DQ23 DQ29 DQ30 CB5 VSS VDDQ DQ37 DQ39 DQ45 DM5/DQS14 NC A13/NC DQ55 DQ61 DQ63 SA2 - Pin 043 Pin 047 Pin 051 Pin 055 Pin 059 Pin 063 Pin 067 Pin 071 Pin 075 Pin 079 Pin 083 Pin 087 Pin 091 Pin 095 Pin 099 Pin 103 Pin 107 Pin 111 Pin 115 Pin 119 Pin 123 Pin 127 Pin 131 Pin 135 Pin 139 Pin 143 Pin 147 Pin 151 Pin 155 Pin 159 Pin 163 Pin 167 Pin 171 Pin 175 Pin 179 Pin 183 Pin 044 Pin 048 Pin 052 Pin 056 Pin 060 Pin 064 Pin 068 Pin 072 Pin 076 Pin 080 Pin 084 Pin 088 Pin 092 Pin 096 Pin 100 Pin 104 Pin 108 Pin 112 Pin 116 Pin 120 Pin 124 Pin 128 Pin 132 Pin 136 Pin 140 Pin 144 Pin 148 Pin 152 Pin 156 Pin 160 Pin 164 Pin 168 Pin 172 Pin 176 Pin 180 Pin 184 - BACKSIDE Pin 001 Pin 005 Pin 009 Pin 013 Pin 017 Pin 021 Pin 025 Pin 029 Pin 033 Pin 037 FRONTSIDE VREF DQS0 NC DQ09 NC CKE0 DQS2 A7 DQ24 A4 - CB00 A0 BA1 DQS4 DQ35 DQ41 DQ42 DQ48 NC DQ51 DQ57 DQ59 SCL VDDQ VSS VDDQ VDD VDDQ VSS VDD VSS VDDQ VSS VDDQ DM8/DQS17 CB07 VDD VSS VDDQ VSS VDDQ VDD VDDQ VSS VDDQ VDDSPD Pin 002 Pin 006 Pin 010 Pin 014 Pin 018 Pin 022 Pin 026 Pin 030 Pin 034 Pin 038 - DQ00 DQ02 RESET DQS1 VSS VDDQ VSS VDDQ VSS VDD Pin 042 Pin 046 Pin 050 Pin 054 Pin 058 Pin 062 Pin 066 Pin 070 Pin 074 Pin 078 Pin 082 Pin 086 Pin 090 Pin 094 Pin 098 Pin 102 Pin 106 Pin 110 Pin 114 Pin 118 Pin 122 Pin 126 Pin 130 Pin 134 Pin 138 Pin 142 Pin 146 Pin 150 Pin 154 Pin 158 Pin 162 Pin 166 Pin 170 Pin 174 Pin 178 Pin 182 - VSS VDD VSS VDDQ VSS VDDQ VSS VDD VSS DQS6 VDDID DQS7 NC DQ04 DQ06 NC DQ13 DQ15 DQ20 A11 A8 DQ28 A3 DQ04 CK0 CB06 DQ36 DQ38 RAS S1 /NC DQ47 DQ53 DQ54 DQ60 DQ62 SA1 MPPD0020 Figure 1 Pin Configuration 184 Pins, Reg Table 6 Address Table Density Organization Memory SDRAMs # of SDRAMs # of row/rank/ Refresh Ranks columns bits Period Interval 256 MB 32 M x72 1 32 M x8 9 13 / 2 / 10 8K 64 ms 7.8 s 512 MB 64 M x72 1 64 M x4 18 13 / 2 / 11 8K 64 ms 7.8 s Data Sheet 12 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration Table 6 Address Table Density Organization Memory SDRAMs # of SDRAMs # of row/rank/ Refresh Ranks columns bits Period Interval 512 MB 64 M x72 2 32 M x8 18 13 / 2 / 10 8K 64 ms 7.8 s 1 GB 128 M x72 2 64 M x4 36 13 / 2 / 11 8K 64 ms 7.8 s CK0 CK0 S0 CKE0 BA0 - BA1 A0 - An RAS CAS WE PCK PCK RESET PCK PCK RS0 RCKE0 RBA0 - RBA1 RA0-RAn RRAS RCAS RWE PLL R E G I S T E R CS: SDRAMs D0- D8 CKE: SDRAMs D0 - D8 BA0 - BA1: SDRAMs D0 - D8 A0 - An: SDRAMs D0 - D8 RAS: SDRAMs D0 - D8 CAS: SDRAMs D0 - D8 WE: SDRAMs D0 - D8 S0 DM0/DQS9 DQS0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM1/DQS10 DQS1 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM2/DQS11 DQS2 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 SCL SAD SA0 SA1 SA2 VSS Figure 2 SCL SAD A0 A1 A2 WP D0 D1 D2 DM3/DQS12 DQS3 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM4/DQS13 DQS4 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM5/DQS14 DQS5 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 E0 VDD,SPD VDD/VDDQ VREF VSS VDDID D4 D5 DM6/DQS15 DQS6 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM7/DQS16 DQS7 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM8/DQS17 DQS8 CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 DM CS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D6 D7 D8 VDD: SPD EEPROM E0 VDD/VDDQ: SDRAMs D0 - D8 VREF: SDRAMs D0 - D8 VSS: SDRAMs D0 - D8 Strap: see Note 1 MPBD1101 Block Diagram Raw Card A x72 1 Rank x8, ECC Notes 3. BAn, An, RAS, CAS, WE resistors are 22 ohms 5% 1. VDD = VDDQ, therefore VDDID strap open 2. DQ, DQS, DM resistors are 22 ohms 5% Data Sheet D3 13 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration CK0 CK0 S0 CKE0 S1 CKE1 BA0 - BA1 A0 - An RAS CAS WE PCK PCK RESET PCK PCK RS0 RCKE0 RS1 RCKE1 RBA0 - RBA1 RA0 - RAn RRAS RCAS RWE PLL R E G I S T E R CKE: SDRAMs D0 - D8 CKE: SDRAMs D9 - D17 BA0 - BA1: SDRAMs D0 - D17 A0 - An: SDRAMs D0 - D17 RAS: SDRAMs D0 - D17 CAS: SDRAMs D0 - D17 WE: SDRAMs D0 - D17 SCL SAD SA0 SA1 SA2 VSS E0 SCL SAD A0 A1 A2 WP S0 S1 DM0/DQS9 DQS0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM1/DQS10 DQS1 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM2/DQS11 DQS2 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM3/DQS12 DQS3 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 VDD,SPD VDD/VDDQ VREF VSS VDDID CS CS CS CS D0 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D1 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D2 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D3 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS CS CS CS D9 DM4/DQS13 DQS4 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM5/DQS14 DQS5 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM6/DQS15 DQS6 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM7/DQS16 DQS7 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM8/DQS17 DQS8 CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D10 D11 D12 VDD: SPD EEPROM E0 VDD/VDDQ: SDRAMs D0 - D17 VREF: SDRAMs D0 - D17 VSS: SDRAMs D0 - D17 DM: SDRAMs D0 - D17 Strap: see Note 1 CS CS CS CS CS D4 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D5 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D6 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D7 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D8 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS CS CS CS CS D13 D14 D15 D16 D17 MPBD1401 Figure 3 Block Diagram Raw Card B x72, 2Ranks x8, ECC Notes 3. BAn, An, RAS, CAS, WE resistors are 22 ohms 5% 4. For Wire per Clock Loading please see Figure: "Diferential Clock Net Wiring" 1. VDD = VDDQ, therefore VDDID strap open 2. DQ, DQS, DM resistors are 22 ohms 5% Data Sheet 14 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration CK0 CK0 S0 CKE0 BA0 - BA1 A0 - An RAS CAS WE PCK PCK RESET PCK PCK RS0 RCKE0 RBA0 - RBA1 RA0 - RAn RRAS RCAS RWE PLL R E G I S T E R CS: SDRAMs D0- D17 CKE: SDRAMs D0 - D17 BA0 - BA1: SDRAMs D0 - D17 A0 - An: SDRAMs D0 - D17 RAS: SDRAMs D0 - D17 CAS: SDRAMs D0 - D17 WE: SDRAMs D0 - D17 RS0 DQS0 DQ0 DQ1 DQ2 DQ3 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS1 DQ8 DQ9 DQ10 DQ11 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS2 DQ16 DQ17 DQ18 DQ19 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS3 DQ24 DQ25 DQ26 DQ27 DQS4 DQ32 DQ33 DQ34 DQ35 DQS5 DQ40 DQ41 DQ42 DQ43 VDD,SPD VDD/VDDQ VREF VSS VDDID DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS CS CS CS CS CS D0 DQS6 DQ48 DQ49 DQ50 DQ51 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS7 DQ56 DQ57 DQ58 DQ59 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS8 CB0 CB1 CB2 CB3 DQS I/O 0 I/O 1 I/O 2 I/O 3 D1 D2 D3 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS9 DQ4 DQ5 DQ6 DQ7 D4 DQS10 DQ12 DQ13 DQ14 DQ15 DQS I/O 0 I/O 1 I/O 2 I/O 3 D5 DQS11 DQ20 DQ21 DQ22 DQ23 DQS I/O 0 I/O 1 I/O 2 I/O 3 VDD: SPD EEPROM E0 VDD/VDDQ: SDRAMs D0 - D17 VREF: SDRAMs D0 - D17 VSS: SDRAMs D0 - D17 Strap: see Note 1 Figure 4 CS CS CS CS CS D6 DQS12 DQ28 DQ29 DQ30 DQ31 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS13 DQ36 DQ37 DQ38 DQ39 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS14 DQ44 DQ45 DQ46 DQ47 DQS I/O 0 I/O 1 I/O 2 I/O 3 D7 D8 D9 DQS15 DQ52 DQ53 DQ54 DQ55 DQS I/O 0 I/O 1 I/O 2 I/O 3 D10 DQS16 DQ60 DQ61 DQ62 DQ63 DQS I/O 0 I/O 1 I/O 2 I/O 3 D11 DQS17 CB4 CB5 CB6 CB7 DQS I/O 0 I/O 1 I/O 2 I/O 3 SCL SAD SA0 SA1 SA2 VSS SCL SAD A0 A1 A2 WP CS CS CS CS CS CS D12 D13 D14 D15 D16 D17 E0 MPBD1501 Block Diagram Raw Card C x72 1 Rank x4, ECC Notes 3. BAn, An, RAS, CAS, WE resistors are 22 ohms 5% 1. VDD = VDDQ, therefore VDDID strap open 2. DQ, DQS, DM resistors are 22 ohms 5% Data Sheet CS 15 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Pin Configuration CK0 CK0 S0 CKE0 S1 CKE1 BA0 - BA1 A0 - An RAS CAS WE PCK PCK RESET PLL R E G I S T E R PCK PCK RS0 RCKE0 RS1 RCKE1 RBA0 - RBA1 RA0-RAn RRAS RCAS RWE BA0 - BA1: SDRAMs D0 - D35 A0 - An: SDRAMs D0 - D35 RAS: SDRAMs D0 - D35 CAS: SDRAMs D0 - D35 WE: SDRAMs D0 - D35 VDD,SPD VDD/VDDQ VREF VSS VDDID Strap: see Note 1 VDD: SPD EEPROM E0 VDD/VDDQ: SDRAMs D0 - D35 VREF: SDRAMs D0 - D35 VSS: SDRAMs D0 - D35 DM: SDRAMs D0 - D35 SCL SAD SA0 SA1 SA2 VSS E0 SCL SAD A0 A1 A2 WP RS0 RCKE0 RS1 RCKE1 DQS0 DQ0 DQ1 DQ2 DQ3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS1 DQ8 DQ9 DQ10 DQ11 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS10 DQ12 DQ13 DQ14 DQ15 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS9 DQ4 DQ5 DQ6 DQ7 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS11 DQ20 DQ21 DQ22 DQ23 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS2 DQ16 DQ17 DQ18 DQ19 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS3 DQ24 DQ25 DQ26 DQ27 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS17 CB4 CB5 CB6 CB7 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS12 DQ28 DQ29 DQ30 DQ31 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 D4 D0 D12 D8 D20 D16 D24 D28 D32 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 D6 DQS7 DQ56 DQ57 DQ58 DQ59 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS6 DQ48 DQ49 DQ50 DQ51 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS15 DQ52 DQ53 DQ54 DQ55 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS16 DQ60 DQ61 DQ62 DQ63 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS14 DQ44 DQ45 DQ46 DQ47 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS5 DQ40 DQ41 DQ42 DQ43 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS4 DQ32 DQ33 DQ34 DQ35 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS8 CB0 CB1 CB2 CB3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS13 DQ36 DQ37 DQ38 DQ39 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 D2 D14 D10 D22 D18 D26 D30 D34 D5 D1 D13 D9 D21 D17 D25 D28 D33 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CKE CS DQS I/O 0 I/O 1 I/O 2 I/O 3 D7 D3 D15 D11 D23 D19 D27 D31 D35 MPBD1061 Figure 5 Block Diagram Raw Card D x72 2 Ranks x4, ECC 3. BAn, An, RAS, CAS, WE resistors are 22 ohms 5% 4. For Wire per Clock Loading please see Figure "Differental Clock Net Wiring" Notes 1. VDD = VDDQ, therefore VDDID strap open 2. DQ, DQS, DM resistors are 18 ohms 5% Data Sheet 16 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Electrical Characteristics 3 Electrical Characteristics 3.1 Operating Conditions Table 7 Absolute Maximum Ratings Parameter Symbol Voltage on I/O pins relative to VSS VIN, VOUT VIN VDD VDDQ TA TSTG PD IOUT Voltage on inputs relative to VSS Voltage on VDD supply relative to VSS Voltage on VDDQ supply relative to VSS Operating temperature (ambient) Storage temperature (plastic) Power dissipation (per SDRAM component) Short circuit output current Values min. typ. max. Unit Note/ Test Condition -0.5 - VDDQ +0.5 V - -1 - +3.6 V - -1 - +3.6 V - -1 - +3.6 V - 0 - +70 C - -55 - +150 C - - 1 - W - - 50 - mA - Attention: Permanent damage to the device may occur if "Absolute Maximum Ratings" are exceeded. This is a stress rating only, and functional operation should be restricted to recommended operation conditions. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability and exceeding only one of the values may cause irreversible damage to the integrated circuit. Table 8 Electrical Characteristics and DC Operating Conditions Parameter Device Supply Voltage Symbol VDD VDD Output Supply Voltage VDDQ Output Supply Voltage VDDQ EEPROM supply voltage VDDSPD Supply Voltage, I/O Supply VSS, Voltage VSSQ VREF Input Reference Voltage I/O Termination Voltage VTT Device Supply Voltage Unit Note/Test Condition 1) Values Min. Typ. Max. 2.3 2.5 2.7 V 2.5 2.6 2.7 V 2.3 2.5 2.7 V 2.5 2.6 2.7 V fCK 166 MHz fCK > 166 MHz 2) fCK 166 MHz 3) fCK > 166 MHz 2)3) 2.3 2.5 3.6 V -- 0 V -- 0 0.49 x VDDQ 0.5 x VDDQ 0.51 x VDDQ V 4) VREF - 0.04 VREF + 0.04 V 5) Input High (Logic1) Voltage VIH(DC) VREF + 0.15 8) Input Low (Logic0) Voltage VIL(DC) -0.3 Input Voltage Level, CK and CK Inputs VIN(DC) -0.3 VDDQ + 0.3 V VREF - 0.15 V VDDQ + 0.3 V Input Differential Voltage, CK and CK Inputs VID(DC) 0.36 VDDQ + 0.6 V 8)6) VI-Matching Pull-up Current to Pull-down Current VIRatio 0.71 1.4 -- 7) (System) Data Sheet 17 8) 8) Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Electrical Characteristics Table 8 Electrical Characteristics and DC Operating Conditions (cont'd) Parameter Symbol Unit Note/Test Condition 1) Values Min. Typ. Max. Input Leakage Current II -2 2 A Any input 0 V VIN VDD; All other pins not under test = 0 V 8)9) Output Leakage Current IOZ -5 5 A DQs are disabled; 0 V VOUT VDDQ Output High Current, Normal Strength Driver IOH -- -16.2 mA VOUT = 1.95 V Output Low Current, Normal Strength Driver IOL 16.2 -- mA VOUT = 0.35 V 1) 0 C TA 70 C 2) DDR400 conditions apply for all clock frequencies above 166 MHz 3) Under all conditions, VDDQ must be less than or equal to VDD. 4) Peak to peak AC noise on VREF may not exceed 2% VREF (DC). VREF is also expected to track noise variations in VDDQ. 5) VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track variations in the DC level of VREF. 6) VID is the magnitude of the difference between the input level on CK and the input level on CK. 7) The ratio of the pull-up current to the pull-down current is specified for the same temperature and voltage, over the entire temperature and voltage range, for device drain to source voltage from 0.25 to 1.0 V. For a given output, it represents the maximum difference between pull-up and pull-down drivers due to process variation. 8) Inputs are not recognized as valid until VREF stabilizes. 9) Values are shown per DDR SDRAM component Data Sheet 18 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Current Specification and Conditions 4 Current Specification and Conditions Table 9 IDD Conditions Parameter Symbol Operating Current 0 one bank; active/ precharge; DQ, DM, and DQS inputs changing once per clock cycle; address and control inputs changing once every two clock cycles. IDD0 Operating Current 1 one bank; active/read/precharge; Burst Length = 4; see component data sheet. IDD1 Precharge Power-Down Standby Current all banks idle; power-down mode; CKE VIL,MAX IDD2P Precharge Floating Standby Current CS VIH,,MIN, all banks idle; CKE VIH,MIN; address and other control inputs changing once per clock cycle; VIN = VREF for DQ, DQS and DM. IDD2F Precharge Quiet Standby Current CS VIHMIN, all banks idle; CKE VIH,MIN; VIN = VREF for DQ, DQS and DM; address and other control inputs stable at VIH,MIN or VIL,MAX. IDD2Q Active Power-Down Standby Current one bank active; power-down mode; CKE VILMAX; VIN = VREF for DQ, DQS and DM. IDD3P Active Standby Current one bank active; CS VIH,MIN; CKE VIH,MIN; tRC = tRAS,MAX; DQ, DM and DQS inputs changing twice per clock cycle; address and control inputs changing once per clock cycle. IDD3N Operating Current Read one bank active; Burst Length = 2; reads; continuous burst; address and control inputs changing once per clock cycle; 50% of data outputs changing on every clock edge; CL = 2 for DDR266(A), CL = 3 for DDR333 and DDR400B; IOUT = 0 mA IDD4R Operating Current Write one bank active; Burst Length = 2; writes; continuous burst; address and control inputs changing once per clock cycle; 50% of data outputs changing on every clock edge; CL = 2 for DDR266(A), CL = 3 for DDR333 and DDR400B IDD4W Auto-Refresh Current tRC = tRFCMIN, burst refresh IDD5 Self-Refresh Current CKE 0.2 V; external clock on IDD6 Operating Current 7 four bank interleaving with Burst Length = 4; see component data sheet. IDD7 Data Sheet 19 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Current Specification and Conditions HYS72D64300GBR-5-C HYS72D64320GBR-5-C IDD Specification for PC3200 HYS72D32300GBR-5-C Part Number & Organization Table 10 256 MB 512 MB 512 MB x72 x72 x72 1 Rank 1 Rank 2 Ranks -5 -5 -5 Unit Note/ Test Conditions1) 2) Symbol Typ. Max. Typ. Max. Typ. Max. IDD0 IDD1 IDD2P IDD2F IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5 IDD6 IDD7 1510 1690 2140 2500 1852 2095 mA 3) 1600 1780 2320 2680 1942 2185 mA 3)4) 680 689 716 734 788 824 mA 5) 914 968 1184 1292 1184 1292 mA 5) 824 896 1004 1148 1004 1148 mA 5) 761 806 878 968 878 968 mA 5) 986 1049 1328 1454 1328 1454 mA 5) 1645 1780 2410 2680 1987 2185 mA 3)4) 1690 1825 2500 2770 2032 2230 mA 3) 2140 2590 3400 4300 2482 2995 mA 3) 657 670 669 694 669 694 mA 5) 2770 3130 4660 5380 3112 3535 mA 3)4) 1) Test condition for maximum values: VDD = 2.7 V, TA = 10 C 2) Module IDD is calculated on the basis of component IDD and includes Register an PLL 3) The module IDD values are calculated from the component IDD datasheet values are: n * IDDx[component] for single bank modules (n: number of components per module bank) n * IDDx[component] + n * IDD3N[component] for two bank modules (n: number of components per module bank) 4) DQ I/O (IDDQ) currents are not included into calculations: module IDD values will be measured differently depending on load conditions 5) The module IDD values are calculated from the component IDD datasheet values are: n * IDDx[component] for single bank modules (n: number of components per module bank) 2 * n * IDDx[component] for single two bank modules (n: number of components per module bank) Data Sheet 20 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Current Specification and Conditions IDD Specification for PC2700 HYS72D32300GBR-6-C HYS72D64300GBR-6-C HYS72D64320GBR-6-C HYS72D128320GBR-6-C Part Number & Organization Table 11 256 MB 512 MB 512 MB 1 GB Unit Note/ Test Conditions1) 2) x72 x72 x72 x72 1 Rank 1 Rank 2 Ranks 2 Ranks -6 -6 -6 -6 Symbol Typ. Max. Typ. Max. Typ. Max. Typ. Max. IDD0 IDD1 IDD2P IDD2F IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5 IDD6 IDD7 1270 1405 1810 2080 1558 1747 2386 2764 mA 3) 1360 1495 1990 2260 1648 1837 2566 2944 mA 3)4) 466 475 502 520 574 610 718 790 mA 5) 655 700 880 970 880 970 1330 1510 mA 5) 583 646 736 862 736 862 1042 1294 mA 5) 529 565 628 700 628 700 826 970 mA 5) 718 772 1006 1114 1006 1114 1582 1798 mA 5) 1360 1495 1990 2260 1648 1837 2566 2944 mA 3)4) 1405 1540 2080 2350 1693 1882 2656 3034 mA 3) 1810 2170 2890 3610 2098 2512 3466 4294 mA 3) 443 455 455 480 455 480 480 531 mA 5) 2350 2665 3970 4600 2638 3007 4546 5284 mA 3)4) 1) Test condition for maximum values: VDD = 2.7 V, TA = 10 C 2) Module IDD is calculated on the basis of component IDD and includes Register an PLL 3) The module IDD values are calculated from the component IDD datasheet values are: n * IDDx[component] for single bank modules (n: number of components per module bank) n * IDDx[component] + n * IDD3N[component] for two bank modules (n: number of components per module bank) 4) DQ I/O (IDDQ) currents are not included into calculations: module IDD values will be measured differently depending on load conditions 5) The module IDD values are calculated from the component IDD datasheet values are: n * IDDx[component] for single bank modules (n: number of components per module bank) 2 * n * IDDx[component] for single two bank modules (n: number of components per module bank) Data Sheet 21 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Current Specification and Conditions 4.1 AC Characteristics Table 12 AC Timing - Absolute Specifications for PC3200 and PC2700 Parameter DQ output access time from CK/CK DQS output access time from CK/CK CK high-level width CK low-level width Clock Half Period Clock cycle time Symbol -5 -6 Unit Note/ Test Condition 1) DDR400B DDR333 Min. Max. Min. Max. -0.5 +0.5 -0.7 +0.7 ns 2)3)4)5) -0.6 +0.6 -0.6 +0.6 ns 2)3)4)5) 0.45 0.55 0.45 0.55 2)3)4)5) 0.45 0.55 0.45 0.55 tCK tCK tAC tDQSCK tCH tCL tHP tCK 2)3)4)5) min. (tCL, tCH) min. (tCL, tCH) ns 2)3)4)5) 5 6 ns CL = 3.0 8 12 2)3)4)5) 6 12 6 12 ns CL = 2.5 2)3)4)5) 7.5 12 7.5 12 ns CL = 2.0 2)3)4)5) DQ and DM input hold time DQ and DM input setup time Control and Addr. input pulse width (each input) DQ and DM input pulse width (each input) Data-out high-impedance time from CK/CK Data-out low-impedance time from CK/CK Write command to 1st DQS latching transition DQS-DQ skew (DQS and associated DQ signals) tDH tDS tIPW 0.4 -- 0.45 -- ns 2)3)4)5) 0.4 -- 0.45 -- ns 2)3)4)5) 2.2 -- 2.2 -- ns 2)3)4)5)6) tDIPW tHZ tLZ tDQSS tDQSQ 1.75 -- 1.75 -- ns 2)3)4)5)6) -- +0.7 -0.7 +0.7 ns 2)3)4)5)7) -0.7 +0.7 -0.7 +0.7 ns 2)3)4)5)7) 0.72 1.25 0.75 1.25 tCK 2)3)4)5) -- +0.40 -- +0.40 ns TFBGA 2)3)4)5) -- +0.50 -- +0.50 ns TFBGA 2)3)4)5) ns 2)3)4)5) 2)3)4)5) tQHS DQ/DQS output hold time tQH DQS input low (high) pulse width (write cycle) tDQSL,H DQS falling edge to CK setup time (write cycle) tDSS DQS falling edge hold time from CK (write tDSH Data hold skew factor tHP -tQHS 0.35 -- 0.35 -- 0.2 -- 0.2 -- 0.2 -- 0.2 -- tCK tCK tCK 2 -- 2 -- tCK 2)3)4)5) 0 -- 0 -- ns 2)3)4)5)8) 0.40 0.60 0.40 0.60 2)3)4)5)9) 0.25 -- 0.25 -- tCK tCK 0.6 -- 0.75 -- ns fast slew rate 2)3)4)5) 2)3)4)5) cycle) Mode register set command cycle time Write preamble setup time Write postamble Write preamble Address and control input setup time Address and control input hold time tMRD tWPRES tWPST tWPRE tIS 3)4)5)6)10) tIH 0.7 -- 0.8 -- ns slow slew rate3)4)5)6)10) 0.6 -- 0.75 -- ns fast slew rate 3)4)5)6)10) 0.7 Data Sheet 2)3)4)5) 22 -- 0.8 -- ns slow slew rate3)4)5)6)10) Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Current Specification and Conditions Table 12 AC Timing - Absolute Specifications for PC3200 and PC2700 Parameter Symbol -5 -6 DDR400B DDR333 Min. Max. Min. Max. 0.9 1.1 0.9 1.1 0.40 0.60 40 Unit Note/ Test Condition 1) 2)3)4)5) 0.40 0.60 tCK tCK 70E+3 42 70E+3 ns 2)3)4)5) 55 -- 60 -- ns 2)3)4)5) 70 -- 72 -- ns 2)3)4)5) tRCD tRP tRAP tRRD tWR tDAL 15 -- 18 -- ns 2)3)4)5) 15 -- 18 -- ns 2)3)4)5) ns 2)3)4)5) tWTR tXSNR tXSRD tREFI 2 -- 1 75 -- 200 -- tRPRE Read postamble tRPST Active to Precharge command tRAS Active to Active/Auto-refresh command period tRC Auto-refresh to Active/Auto-refresh command tRFC Read preamble 2)3)4)5) period Active to Read or Write delay Precharge command period Active to Autoprecharge delay Active bank A to Active bank B command Write recovery time Auto precharge write recovery + precharge time Internal write to read command delay Exit self-refresh to non-read command Exit self-refresh to read command Average Periodic Refresh Interval tRCD or tRASmin 10 -- 12 -- ns 2)3)4)5) 15 -- 15 -- ns 2)3)4)5) tCK 2)3)4)5)11) -- tCK 2)3)4)5) 75 -- ns 2)3)4)5) -- 200 -- tCK 2)3)4)5) 7.8 -- 7.8 s 2)3)4)5)12) (tWR/tCK)+(tRP/tCK) 1) 0 C TA 70 C; VDDQ = 2.5 V 0.2 V, VDD = +2.5 V 0.2 V (DDR333); VDDQ = 2.6 V 0.1 V, VDD = +2.6 V 0.1 V (DDR400) 2) Input slew rate 1 V/ns for DDR400, DDR333 3) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross: the input reference level for signals other than CK/CK, is VREF. CK/CK slew rate are 1.0 V/ns. 4) Inputs are not recognized as valid until VREF stabilizes. 5) The Output timing reference level, as measured at the timing reference point indicated in AC Characteristics (note 3) is VTT. 6) These parameters guarantee device timing, but they are not necessarily tested on each device. 7) tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referred to a specific voltage level, but specify when the device is no longer driving (HZ), or begins driving (LZ). 8) The specific requirement is that DQS be valid (HIGH, LOW, or some point on a valid transition) on or before this CK edge. A valid transition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in progress on the bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS. 9) The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 10) Fast slew rate 1.0 V/ns , slow slew rate 0.5 V/ns and < 1 V/ns for command/address and CK & CK slew rate > 1.0 V/ns, measured between VIH(ac) and VIL(ac). 11) For each of the terms, if not already an integer, round to the next highest integer. tCK is equal to the actual system clock cycle time. 12) A maximum of eight Autorefresh commands can be posted to any given DDR SDRAM device. Data Sheet 23 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM SPD Contents SPD Codes for HYS72D[128/64/32][300/320]GBR-5-C 512 MB 512 MB 256 MB x72 x72 x72 1 Rank 2 Ranks 1 Rank Label Code PC3200R-30331 PC3200R-30331 PC3200R-30331 Jedec SPD Revision Rev 1.0 Rev 1.0 Rev 1.0 Byte# Description HEX HEX HEX 0 Programmed SPD Bytes in E2PROM 80 80 80 1 Total number of Bytes in E2PROM 08 08 08 2 Memory Type (DDR = 07h) 07 07 07 3 Number of Row Addresses 0D 0D 0D 4 Number of Column Addresses 0B 0A 0A 5 Number of DIMM Ranks 01 02 01 6 Data Width (LSB) 48 48 48 7 Data Width (MSB) 00 00 00 8 Interface Voltage Levels 04 04 04 9 tCK @ CLmax (Byte 18) [ns] 50 50 50 10 tAC SDRAM @ CLmax (Byte 18) [ns] 50 50 50 11 Error Correction Support 02 02 02 12 Refresh Rate 82 82 82 Product Type & Organization HYS72D32300GBR-5-C Table 13 HYS72D64320GBR-5-C SPD Contents HYS72D64300GBR-5-C 5 13 Primary SDRAM Width 04 08 08 14 Error Checking SDRAM Width 04 08 08 15 tCCD [cycles] 01 01 01 16 Burst Length Supported 0E 0E 0E 17 Number of Banks on SDRAM Device 04 04 04 18 CAS Latency 1C 1C 1C 19 CS Latency 01 01 01 20 Write Latency 02 02 02 21 DIMM Attributes 26 26 26 22 Component Attributes C1 C1 C1 23 tCK @ CLmax -0.5 (Byte 18) [ns] 60 60 60 24 tAC SDRAM @ CLmax -0.5 [ns] 50 50 50 25 tCK @ CLmax -1 (Byte 18) [ns] 75 75 75 Data Sheet 24 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM SPD Contents HYS72D64300GBR-5-C HYS72D64320GBR-5-C HYS72D32300GBR-5-C SPD Codes for HYS72D[128/64/32][300/320]GBR-5-C Product Type & Organization Table 13 512 MB 512 MB 256 MB x72 x72 x72 1 Rank 2 Ranks 1 Rank Label Code PC3200R-30331 PC3200R-30331 PC3200R-30331 Jedec SPD Revision Rev 1.0 Rev 1.0 Rev 1.0 Byte# Description HEX HEX HEX 26 tAC SDRAM @ CLmax -1 [ns] 50 50 50 27 tRPmin [ns] 3C 3C 3C 28 tRRDmin [ns] 28 28 28 29 tRCDmin [ns] 3C 3C 3C 30 tRASmin [ns] 28 28 28 31 Module Density per Rank 80 40 40 32 tAS, tCS [ns] 60 60 60 33 tAH, TCH [ns] 60 60 60 34 tDS [ns] 40 40 40 35 tDH [ns] 40 40 40 36 - 40 not used 00 00 00 41 tRCmin [ns] 37 37 37 42 tRFCmin [ns] 41 41 41 43 tCKmax [ns] 28 28 28 44 tDQSQmax [ns] 28 28 28 45 tQHSmax [ns] 50 50 50 46 not used 00 00 00 47 DIMM PCB Height 01 01 01 48 - 61 not used 00 00 00 62 SPD Revision 10 10 10 63 Checksum of Byte 0-62 5F 27 26 64 JEDEC ID Code of Infineon (1) C1 C1 C1 65 - 71 JEDEC ID Code of Infineon (2 - 8) 00 00 00 72 Module Manufacturer Location xx xx xx 73 Part Number, Char 1 37 37 37 74 Part Number, Char 2 32 32 32 75 Part Number, Char 3 44 44 44 76 Part Number, Char 4 36 36 33 Data Sheet 25 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM SPD Contents HYS72D32300GBR-5-C 512 MB 512 MB 256 MB x72 x72 x72 1 Rank 2 Ranks 1 Rank Label Code PC3200R-30331 PC3200R-30331 PC3200R-30331 Jedec SPD Revision Rev 1.0 Rev 1.0 Rev 1.0 Byte# Description HEX HEX HEX 77 Part Number, Char 5 34 34 32 78 Part Number, Char 6 33 33 33 79 Part Number, Char 7 30 32 30 80 Part Number, Char 8 30 30 30 81 Part Number, Char 9 47 47 47 82 Part Number, Char 10 42 42 42 83 Part Number, Char 11 52 52 52 84 Part Number, Char 12 35 35 35 85 Part Number, Char 13 43 43 43 86 Part Number, Char 14 20 20 20 87 Part Number, Char 15 20 20 20 88 Part Number, Char 16 20 20 20 89 Part Number, Char 17 20 20 20 Product Type & Organization HYS72D64320GBR-5-C SPD Codes for HYS72D[128/64/32][300/320]GBR-5-C HYS72D64300GBR-5-C Table 13 90 Part Number, Char 18 20 20 20 91 Module Revision Code xx xx xx 92 Test Program Revision Code xx xx xx 93 Module Manufacturing Date Year xx xx xx 94 Module Manufacturing Date Week xx xx xx 95 - 98 Module Serial Number (1 - 4) xx xx xx 99 - 127 Blank FF FF FF Data Sheet 26 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM SPD Contents HYS72D64320GBR-6-C HYS72D32300GBR-6-C 1 GByte 512 MB 512 MB 256 MB x72 x72 x72 x72 2 Ranks 1 Rank 2 Ranks 1 Rank Label Code PC2700R- 25330 PC2700R- 25330 PC2700R- 25330 PC2700R- 25330 Jedec SPD Revision Rev 0.0 Rev 0.0 Rev 0.0 Rev 0.0 Byte# Description HEX HEX HEX HEX 0 Programmed SPD Bytes in E2PROM 80 80 80 80 1 Total number of Bytes in E2PROM 08 08 08 08 2 Memory Type (DDR = 07h) 07 07 07 07 3 Number of Row Addresses 0D 0D 0D 0D 4 Number of Column Addresses 0B 0B 0A 0A 5 Number of DIMM Ranks 02 01 02 01 6 Data Width (LSB) 48 48 48 48 7 Data Width (MSB) 00 00 00 00 8 Interface Voltage Levels 04 04 04 04 9 tCK @ CLmax (Byte 18) [ns] 60 60 60 60 10 tAC SDRAM @ CLmax (Byte 18) [ns] 70 70 70 70 11 Error Correction Support 02 02 02 02 12 Refresh Rate 82 82 82 82 13 Primary SDRAM Width 04 04 08 08 14 Error Checking SDRAM Width 04 04 08 08 15 tCCD [cycles] 01 01 01 01 16 Burst Length Supported 0E 0E 0E 0E Product Type & Organization HYS72D64300GBR-6-C SPD Codes for HYS72D[128/64/32][300/320]GBR-6-C HYS72D128320GBR-6-C Table 14 17 Number of Banks on SDRAM Device 04 04 04 04 18 CAS Latency 0C 0C 0C 0C 19 CS Latency 01 01 01 01 20 Write Latency 02 02 02 02 21 DIMM Attributes 26 26 26 26 22 Component Attributes C1 C1 C1 C1 23 tCK @ CLmax -0.5 (Byte 18) [ns] 75 75 75 75 24 tAC SDRAM @ CLmax -0.5 [ns] 70 70 70 70 25 tCK @ CLmax -1 (Byte 18) [ns] 00 00 00 00 Data Sheet 27 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM SPD Contents HYS72D64320GBR-6-C HYS72D32300GBR-6-C 1 GByte 512 MB 512 MB 256 MB x72 x72 x72 x72 2 Ranks 1 Rank 2 Ranks 1 Rank Label Code PC2700R- 25330 PC2700R- 25330 PC2700R- 25330 PC2700R- 25330 Jedec SPD Revision Rev 0.0 Rev 0.0 Rev 0.0 Rev 0.0 Byte# Description HEX HEX HEX HEX 26 tAC SDRAM @ CLmax -1 [ns] 00 00 00 00 27 tRPmin [ns] 48 48 48 48 28 tRRDmin [ns] 30 30 30 30 29 tRCDmin [ns] 48 48 48 48 30 tRASmin [ns] 2A 2A 2A 2A 31 Module Density per Rank 80 80 40 40 32 tAS, tCS [ns] 75 75 75 75 33 tAH, TCH [ns] 75 75 75 75 34 tDS [ns] 45 45 45 45 35 tDH [ns] 45 45 45 45 36 - 40 not used 00 00 00 00 41 tRCmin [ns] 3C 3C 3C 3C 42 tRFCmin [ns] 48 48 48 48 43 tCKmax [ns] 30 30 30 30 44 tDQSQmax [ns] 28 28 28 28 45 tQHSmax [ns] 50 50 50 50 46 not used 00 00 00 00 47 DIMM PCB Height 00 00 00 00 48 - 61 not used 00 00 00 00 62 SPD Revision 00 00 00 00 63 Checksum of Byte 0-62 49 48 10 0F 64 JEDEC ID Code of Infineon (1) C1 C1 C1 C1 65 - 71 JEDEC ID Code of Infineon (2 - 8) 00 00 00 00 72 Module Manufacturer Location xx xx xx xx 73 Part Number, Char 1 37 37 37 37 74 Part Number, Char 2 32 32 32 32 75 Part Number, Char 3 44 44 44 44 Product Type & Organization HYS72D64300GBR-6-C SPD Codes for HYS72D[128/64/32][300/320]GBR-6-C HYS72D128320GBR-6-C Table 14 Data Sheet 28 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM SPD Contents HYS72D64320GBR-6-C HYS72D32300GBR-6-C 1 GByte 512 MB 512 MB 256 MB x72 x72 x72 x72 2 Ranks 1 Rank 2 Ranks 1 Rank Label Code PC2700R- 25330 PC2700R- 25330 PC2700R- 25330 PC2700R- 25330 Jedec SPD Revision Rev 0.0 Rev 0.0 Rev 0.0 Rev 0.0 Byte# Description HEX HEX HEX HEX 76 Part Number, Char 4 31 36 36 33 77 Part Number, Char 5 32 34 34 32 78 Part Number, Char 6 38 33 33 33 79 Part Number, Char 7 33 30 32 30 80 Part Number, Char 8 32 30 30 30 81 Part Number, Char 9 30 47 47 47 82 Part Number, Char 10 47 42 42 42 83 Part Number, Char 11 42 52 52 52 84 Part Number, Char 12 52 36 36 36 85 Part Number, Char 13 36 43 43 43 86 Part Number, Char 14 43 20 20 20 87 Part Number, Char 15 20 20 20 20 88 Part Number, Char 16 20 20 20 20 89 Part Number, Char 17 20 20 20 20 90 Part Number, Char 18 20 20 20 20 91 Module Revision Code xx xx xx xx 92 Test Program Revision Code xx xx xx xx 93 Module Manufacturing Date Year xx xx xx xx 94 Module Manufacturing Date Week xx xx xx xx 95 - 98 Module Serial Number (1 - 4) xx xx xx xx 99 -127 Blank FF FF FF0 FF Product Type & Organization HYS72D64300GBR-6-C SPD Codes for HYS72D[128/64/32][300/320]GBR-6-C HYS72D128320GBR-6-C Table 14 Data Sheet 29 Rev. 1.0, 2004-03 07302003-2MI6-FOP1 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Package Outlines Package Outlines 0.1 A B C 6 133.35 0.15 A B C 128.95 2.64 MAX. 28.58 0.13 4 0.1 A 1 2.5 0.1 o0.1 A B C 92 6.62 B 2.175 0.4 6.35 64.77 C 1.27 0.1 49.53 1.8 0.1 0.1 A B C 184 17.8 93 10 3.8 0.13 95 x 1.27 = 120.65 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C Burr max. 0.4 allowed Figure 6 Data Sheet L-DIMM-184-021 Package Outlines - Raw Card A HYS72D32300GBR-[5/6]-C (1 Rank x 8) 30 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM 0.1 A B C Package Outlines 133.35 0.15 A B C 128.95 4 MAX. 28.58 0.13 4 0.1 A 1 2.5 0.1 o0.1 A B C 92 6.62 B C 2.175 0.4 6.35 64.77 1.27 0.1 49.53 1.8 0.1 0.1 A B C 184 17.8 93 10 3.8 0.13 95 x 1.27 = 120.65 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C Burr max. 0.4 allowed L-DIMM-184-22-2 Figure 7 Data Sheet Package Outlines - Raw Card C HYS72D64300GBR-[5/6]-C (1 Rank x 4) 31 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM 0.1 A B C Package Outlines 133.35 0.15 A B C 128.95 4 MAX. 28.58 0.13 4 0.1 A 1 2.5 0.1 o0.1 A B C 92 6.62 B C 2.175 0.4 6.35 64.77 1.27 0.1 49.53 1.8 0.1 0.1 A B C 184 17.8 93 10 3.8 0.13 95 x 1.27 = 120.65 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C Burr max. 0.4 allowed Figure 8 Data Sheet L-DIMM-184-23 Package Outlines - Raw Card B HYS72D64320GBR-[5/6]-C (2 Ranks x8) 32 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Package Outlines 0.1 A B C 133.35 0.15 A B C 128.95 4 MAX. 30.48 0.13 4 0.1 A 1 2.5 0.1 o0.1 A B C 92 6.62 B C 2.175 0.4 6.35 64.77 1.27 0.1 49.53 0.1 A B C 93 184 17.8 1.8 0.1 10 3.8 0.13 95 x 1.27 = 120.65 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C L-DIMM-184-24-3 Burr max. 0.4 allowed Figure 9 Data Sheet Package Outlines - Raw Card D HYS72D128320GBR-[5/6]-C (2 Ranks x4) 33 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Application Note 7 Application Note Power Up and Power Management on DDR Registered DIMMs (according to JEDEC ballot JC-42.5 Item 1173) 184-pin Double Data Rate (DDR) Registered DIMMs include two new features to facilitate controlled power-up and to minimize power consumption during low power mode. One feature is externally controlled via a systemgenerated RESET signal; the second is based on module detection of the input clocks. These enhancements permit the modules to power up with SDRAM outputs in a High-Z state (eliminating risk of high current dissipations and/or dotted I/Os), and result in the powering-down of module support devices (registers and Phase-Locked Loop) when the memory is in Self-Refresh mode. The new RESET pin controls power dissipation on the module's registers and ensures that CKE and other SDRAM inputs are maintained at a valid `low' level during power-up and self refresh. When RESET is at a low level, all the register outputs are forced to a low level, and all differential register input receivers are powered down, resulting in very low register power consumption. The RESET pin, located on DIMM tab #10, is driven from the system as an asynchronous signal according to the attached details. Using this function also permits the system and DIMM clocks to be stopped during memory Self Refresh operation, while ensuring that the SDRAMs stay in Self Refresh mode. Table 15 RESET Truth Table Register Inputs Register Outputs RESET CK CK Data in (D) Data out (Q) H Rising Falling H H H Rising Falling L L H L or H L or H X Qo H High Z High Z X Illegal input conditions L X or Hi-Z X or Hi-Z X or Hi-Z L X: Don't care, Hi-Z: High Impedance, Qo: Data latched at the previous of CK rising and CK falling As described in the table above, a low on the RESET input ensures that the Clock Enable (CKE) signal(s) are maintained low at the SDRAM pins (CKE being one of the 'Q' signals at the register output). Holding CKE low maintains a high impedance state on the SDRAM DQ, DQS and DM outputs -- where they will remain until activated by a valid `read' cycle. CKE low also maintains SDRAMs in Self Refresh mode when applicable. The DDR PLL devices automatically detect clock activity above 20MHz. When an input clock frequency of 20MHz or greater is detected, the PLL begins operation and initiates clock frequency lock (the minimum operating frequency at which all specifications will be met is 95MHz). If the clock input frequency drops below 20MHz (actual detect frequency will vary by vendor), the PLL VCO (Voltage Controlled Oscillator) is stopped, outputs are made High-Z, and the differential inputs are powered down -- resulting in a total PLL current consumption of less than 1mA. Use of this low power PLL function makes the use of the PLL RESET (or G pin) unnecessary, and it is tied inactive on the DIMM. This application note describes the required and optional system sequences associated with the DDR Registered DIMM 'RESET' function. It is important to note that all references to CKE refer to both CKE0 and CKE1 for a 2bank DIMM. Because RESET applies to all DIMM register devices, it is therefore not possible to uniquely control CKE to one physical DIMM bank through the use of the RESET pin. Data Sheet 34 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Application Note Power-Up Sequence with RESET -- Required 1. The system sets RESET at a valid low level. This is the preferred default state during power-up. This input condition forces all register outputs to a low state independent of the condition on the register inputs (data and clock), ensuring that CKE is at a stable low-level at the DDR SDRAMs. 2. The power supplies should be initialized according to the JEDEC-approved initialization sequence for DDR SDRAMs. 3. Stabilization of Clocks to the SDRAM The system must drive clocks to the application frequency (PLL operation is not assured until the input clock reaches 20 MHz). Stability of clocks at the SDRAMs will be affected by all applicable system clock devices, and time must be allotted to permit all clock devices to settle. Once a stable clock is received at the DIMM PLL, the required PLL stabilization time (assuming power to the DIMM is stable) is 100 microseconds. When a stable clock is present at the SDRAM input (driven from the PLL), the DDR SDRAM requires 200 sec prior to SDRAM operation. 4. The system applies valid logic levels to the data inputs of the register (address and controls at the DIMM connector). CKE must be maintained low and all other inputs should be driven to a known state. In general these commands can be determined by the system designer. One option is to apply an SDRAM `NOP' command (with CKE low), as this is the first command defined by the JEDEC initialization sequence (ideally this would be a `NOP Deselect' command). A second option is to apply low levels on all of the register inputs to be consistent with the state of the register outputs. 5. The system switches RESET to a logic `high' level. The SDRAM is now functional and prepared to receive commands. Since the RESET signal is asynchronous, setting the RESET timing in relation to a specific clock edge is not required (during this period, register inputs must remain stable). 6. The system must maintain stable register inputs until normal register operation is attained. The registers have an activation time that allows their clock receivers, data input receivers, and output drivers sufficient time to be turned on and become stable. During this time the system must maintain the valid logic levels described in step 5. It is also a functional requirement that the registers maintain a low state at the CKE outputs to guarantee that the DDR SDRAMs continue to receive a low level on CKE. Register activation time (t (ACT) ), from asynchronous switching of RESET from low to high until the registers are stable and ready to accept an input signal, is specified in the register and DIMM do-umentation. 7. The system can begin the JEDEC-defined DDR SDRAM power-up sequence (according to the JEDECpproved initialization sequence). Self Refresh Entry (RESET low, clocks powered off) -- Optional Self Refresh can be used to retain data in DDR SDRAM DIMMs even if the rest of the system is powered down and the clocks are off. This mode allows the DDR SDRAMs on the DIMM to retain data without external clocking. Self Refresh mode is an ideal time to utilize the RESET pin, as this can reduce register power consumption (RESET low deactivates register CK and CK, data input receivers, and data output drivers). 1. 1. The system applies Self Refresh entry command. (CKELow, CSLow, RAS Low, CAS Low, WE High) Note: Note: The commands reach the DDR SDRAM one clock later due to the additional register pipelining on a Registered DIMM. After this command is issued to the SDRAM, all of the address and control and clock input conditions to the SDRAM are Don't Cares-- with the exception of CKE. 2. The system sets RESET at a valid low level. This input condition forces all register outputs to a low state, independent of the condition on the registerm inputs (data and clock), and ensures that CKE, and all other control and address signals, are a stable low-level at the DDR SDRAMs. Since the RESET signal is asynchronous, setting the RESET timing in relation to a specific clock edge is not required. 3. The system turns off clock inputs to the DIMM. (Optional) a. In order to reduce DIMM PLL current, the clock inputs to the DIMM are turned off, resulting in High-Z clock Data Sheet 35 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Application Note inputs to both the SDRAMs and the registers. This must be done after the RESET deactivate time of the register (t (INACT). The deactivate time defines the time in which the clocks and the control and address signals must maintain valid levels after RESET low has been applied and is specified in the register and DIMM documentation. b.The system may release DIMM address and control inputs to High-Z. This can be done after the RESET deactivate time of the register. The deactivate time defines the time in which the clocks and the control and the address signals must maintain valid levels after RESET low has been applied. It is highly recommended that CKE continue to remain low during this operation. 4. The DIMM is in lowest power Self Refresh mode. Self Refresh Exit (RESET low, clocks powered off) -- Optional 1. Stabilization of Clocks to the SDRAM. The system must drive clocks to the application frequency (PLL operation is not assured until the input clock reaches ~20MHz). Stability of clocks at the SDRAMs will be affected by all applicable system clock devices, and time must be allotted to permit all clock devices to settle. Once a stable clock is received at the DIMM PLL, the required PLL stabilization time (assuming power to the DIMM is stable) is 100 microseconds. 2. The system applies valid logic levels to the data inputs of the register (address and controls at the DIMM connector). CKE must be maintained low and all other inputs should be driven to a known state. In general these commands can be determined by the system designer. One option is to apply an SDRAM `NOP' command (with CKE low), as this is the first command defined by the JEDEC Self Refresh Exit sequence (ideally this would be a `NOP Deselect' command). A second option is to apply low levels on all of the register inputs, to be consistent with the state of the register outputs. 3. The system switches RESET to a logic `high' level. The SDRAM is now functional and prepared to receive commands. Since the RESET signal is asynchronous, RESET timing relationship to a specific clock edge is not required (during this period, register inputs must remain stable). 4. The system must maintain stable register inputs until normal register operation is attained. The registers have an activation time that allows the clock receivers, input receivers, and output drivers sufficient time to be turned on and become stable. During this time the system must maintain the valid logic levels described in Step 2. It is also a functional requirement that the registers maintain a low state at the CKE outputs to guarantee that the DDR SDRAMs continue to receive a low level on CKE. Register activation time (t (ACT) ), from asynchronous switching of RESET from low to high until the registers are stable and ready to accept an input signal, is specified in the register and DIMM do-umentation. 5. System can begin the JEDEC-defined DDR SDRAM Self Refresh Exit Procedure. Self Refresh Entry (RESET low, clocks running) -- Optional Although keeping the clocks running increases power consumption from the on-DIMM PLL during self refresh, this is an alternate operating mode for these DIMMs. 1. 1. System enters Self Refresh entry command. (CKE Low, CS Low, RAS Low, CAS Low, WE High) Note: Note: The commands reach the DDR SDRAM one clock later due to the additional register pipelining on a Registered DIMM. After this command is issued to the SDRAM, all of the address and control and clock input conditions to the SDRAM are Don't Cares -- with the exception of CKE. 2. The system sets RESET at a valid low level. This input condition forces all register outputs to a low state, independent of the condition on the data and clock register inputs, and ensures that CKE is a stable low-level at the DDR SDRAMs. 3. The system may release DIMM address and control inputs to High-Z. This can be done after the RESET deactivate time of the register (t (INACT) ). The deactivate time describes the time in which the clocks and the control and the address signals must maintain valid levels after RESET low has been applied. It is highly recommended that CKE continue to remain low during the operation. 4. The DIMM is in a low power, Self Refresh mode. Data Sheet 36 Rev. 1.0, 2004-03 HYS72D[128/64/32][300/320]GBR-[5/6]-C Registered Double Data Rate SDRAM Application Note Self Refresh Exit (RESET low, clocks running) -- Optional 1. The system applies valid logic levels to the data inputs of the register (address and controls at the DIMM connector). CKE must be maintained low and all other inputs should be driven to a known state. In general these commands can be determined by the system designer. One option is to apply an SDRAM `NOP' command (with CKE low), as this is the first command defined by the Self Refresh Exit sequence (ideally this would be a `NOP Deselect' command). A second option is to apply low levels on all of the register inputs to be consistent with the state of the register outputs. 2. The system switches RESET to a logic 'high' level. The SDRAM is now functional and prepared to receive commands. Since the RESET signal is asynchronous, it does not need to be tied to a particular clock edge (during this period, register inputs must continue to remain stable). 3. The system must maintain stable register inputs until normal register operation is attained. The registers have an activation time that allows the clock receivers, input receivers, and output drivers sufficient time to be turned on and become stable. During this time the system must maintain the valid logic levels described in Step 1. It is also a functional requirement that the registers maintain a low state at the CKE outputs in order to guarantee that the DDR SDRAMs continue to receive a low level on CKE. This activation time, from asynchronous switching of RESET from low to high, until the registers are stable and ready to accept an input signal, is t (ACT ) as specified in the register and DIMM documentation. 4. The system can begin JEDEC defined DDR SDRAM Self Refresh Exit Procedure. Self Refresh Entry/Exit (RESET high, clocks running) -- Optional As this sequence does not involve the use of the RESET function, the JEDEC standard SDRAM specification explains in detail the method for entering and exiting Self Refresh for this case. Self Refresh Entry (RESET high, clocks powered off) -- Not Permissible In order to maintain a valid low level on the register output, it is required that either the clocks be running and the system drive a low level on CKE, or the clocks are powered off and RESET is asserted low according to the sequence defined in this application note. In the case where RESET remains high and the clocks are powered off, the PLL drives a High-Z clock input into the register clock input. Without the low level on RESET an unknown DIMM state will result. Data Sheet 37 Rev. 1.0, 2004-03 www.infineon.com Published by Infineon Technologies AG