NuMicroTM M052/M054 Data Sheet ARM CortexTM-M0 32-BIT MICROCONTROLLER NuMicroTM Family M052/M054 Data Sheet -1- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet TABLE OF CONTENTS 1 GENERAL DESCRIPTION 6 2 FEATURES7 3 BLOCK DIAGRAM11 4 SELECTION TABLE 12 5 PIN CONFIGURATION 13 5.1 QFN 33 pin 13 5.2 LQFP 48 pin 14 5.3 Pin Description15 6 FUNCTIONAL DESCRIPTION 18 6.1 ARM(R) CortexTM-M0 Core 18 6.2 System Manager 20 6.2.1 Overview20 6.2.2 System Reset20 6.2.3 System Power Architecture 20 6.2.4 Whole System Memory Map 22 6.2.5 Whole System Memory Mapping Table24 6.2.6 System Timer (SysTick) 25 6.2.7 Nested Vectored Interrupt Controller (NVIC) 26 6.3 Clock Controller 27 6.3.1 Overview27 6.3.2 Clock Generator Block Diagram 27 6.3.3 System Clock and SysTick Clock 30 6.3.4 AHB Clock Source Select 31 6.3.5 Peripherals Clock Source Select 32 6.3.6 Power Down Mode Clock33 6.3.7 Frequency Divider Output 34 6.4 General Purpose I/O 35 6.4.1 Overview35 6.5 I2C Serial Interface Controller (Master/Slave) 37 6.5.1 Overview37 6.5.2 Features37 6.6 PWM Generator and Capture Timer39 6.6.1 Overview39 6.6.2 Features40 6.7 Serial Peripheral Interface (SPI) Controller 41 6.7.1 Overview41 6.7.2 Features41 6.8 Timer Controller 42 -2- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.8.1 6.8.2 Overview42 Features42 6.9 Watchdog Timer (WDT)43 6.9.1 Overview43 6.9.2 Features46 6.10 UART Interface Controller47 6.10.1 Overview47 6.10.2 Features50 6.11 Analog-to-Digital Converter (ADC) 51 6.11.1 Overview51 6.11.2 Features51 6.12 External Bus Interface (EBI) 53 6.12.1 Overview53 6.12.2 Features53 6.13 Flash Memory Controller (FMC) 54 6.13.1 Overview54 6.13.2 Features54 7 TYPICAL APPLICATION CIRCUIT55 8 ELECTRICAL CHARACTERISTICS56 8.1 Absolute Maximum Ratings 56 8.2 DC Electrical Characteristics 57 8.3 AC Electrical Characteristics 60 8.3.1 External 4~24 MHz High Speed Crystal 60 8.3.2 External 4~24 MHz High Speed Oscillator60 8.3.3 Typical Crystal Application Circuits 61 8.3.4 Internal 22.1184 MHz High Speed Oscillator62 8.3.5 Internal 10 kHz Low Speed Oscillator62 8.4 Analog Characteristics63 8.4.1 Specification of 600 kHz sps 12-bit SARADC63 8.4.2 Specification of LDO and Power management64 8.4.3 Specification of Low Voltage Reset65 8.4.4 Specification of Brownout Detector 65 8.4.5 Specification of Power-On Reset (5V) 65 8.5 SPI Dynamic characteristics 66 9 PACKAGE DIMENSIONS68 9.1 LQFP-48 (7x7x1.4mm2 Footprint 2.0mm)68 9.2 QFN-33 (5X5 mm2, Thickness 0.8mm, Pitch 0.5 mm) 69 10 REVISION HISTORY70 -3- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet LIST OF FIGURES Figure 3-1 NuMicroTM M051 Series Block Diagram ....................................................................... 11 Figure 4-1 NuMicro M051TM Naming Rule..................................................................................... 12 Figure 5-1 NuMicroTM M051 Series QFN33 Pin Diagram............................................................... 13 Figure 5-2 NuMicroTM M051 Series LQFP-48 Pin Diagram........................................................... 14 Figure 6-1 Functional Block Diagram............................................................................................. 18 Figure 6-2 NuMicro M051TM Series Power Architecture Diagram .................................................. 21 Figure 6-3 Whole Chip Clock generator block diagram ................................................................. 28 Figure 6-4 Clock generator block diagram..................................................................................... 29 Figure 6-5 System Clock Block Diagram ....................................................................................... 30 Figure 6-6 SysTick clock Control Block Diagram........................................................................... 30 Figure 6-7 AHB Clock Source for HCLK ........................................................................................ 31 Figure 6-8 Peripherals Clock Source Select for PCLK .................................................................. 32 Figure 6-9 Clock Source of Frequency Divider .............................................................................. 34 Figure 6-10 Block Diagram of Frequency Divider .......................................................................... 34 Figure 6-11 Push-Pull Output......................................................................................................... 35 Figure 6-12 Open-Drain Output ..................................................................................................... 36 Figure 6-13 Quasi-bidirectional I/O Mode ...................................................................................... 36 Figure 6-14 I2C Bus Timing ............................................................................................................ 37 Figure 6-15 Timing of Interrupt and Reset Signal .......................................................................... 45 Figure 8-1 Typical Crystal Application Circuit ................................................................................ 61 Figure 8-2 SPI Master timing ......................................................................................................... 67 Figure 8-3 SPI Slave timing ........................................................................................................... 67 -4- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet LIST OF TABLES Table 4-1 NuMicroTM M051 Series Product Selection Guide......................................................... 12 Table 5-1 NuMicroTM M051 Series Pin Description ........................................................................ 17 Table 6-1 Address Space Assignments for On-Chip Modules ...................................................... 23 Table 6-2 Watchdog Timeout Interval Selection ............................................................................ 44 Table 6-3 UART Baud Rate Equation ............................................................................................ 47 Table 6-4 UART Baud Rate Setting Table ..................................................................................... 48 -5- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 1 GENERAL DESCRIPTION The NuMicro M051TM series is a 32-bit microcontroller with embedded ARM(R) CortexTM-M0 core for industrial control and applications which need rich communication interfaces. The CortexTM-M0 is the newest ARM embedded processor with 32-bit performance and at a cost equivalent to traditional 8-bit microcontroller. The NuMicro M051TM series includes M052, M054, M058 and M0516 families. The M052/M054 can run up to 50 MHz. Thus it can afford to support a variety of industrial control and applications which need high CPU performance. The M052/M054 has 8K/16K-byte embedded flash, 4K-byte data flash, 4K-byte flash for the ISP, and 4K-byte embedded SRAM. Many system level peripheral functions, such as I/O Port, EBI (External Bus Interface), Timer, UART, SPI, I2C, PWM, ADC, Watchdog Timer and Brownout Detector, have been incorporated into the M052/M054 in order to reduce component count, board space and system cost. These useful functions make the M052/M054 powerful for a wide range of applications. Additionally, the M052/M054 is equipped with ISP (In-System Programming) and ICP (In-Circuit Programming) functions, which allow the user to update the program memory without removing the chip from the actual end product. -6- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 2 FEATURES z Core ARM(R) CortexTM-M0 core runs up to 50 MHz. One 24-bit system timer. Supports low power sleep mode. A single-cycle 32-bit hardware multiplier. NVIC for the 32 interrupt inputs, each with 4-levels of priority. Supports Serial Wire Debug (SWD) interface and 2 watchpoints/4 breakpoints. z Built-in LDO for Wide Operating Voltage Range: 2.5V to 5.5V z Memory z z 8KB/16KB Flash memory for program memory (APROM) 4KB Flash memory for data memory (DataFlash) 4KB Flash memory for loader (LDROM) 4KB SRAM for internal scratch-pad RAM (SRAM) Clock Control Programmable system clock source External 4~24 MHz high speed crystal input Internal 22.1184 MHz high speed oscillator (trimmed to 1% accuracy) Internal 10 kHz low speed oscillator for Watchdog Timer PLL allows CPU operation up to the maximum 50MHz I/O Port Up to 40 general-purpose I/O (GPIO) pins for LQFP-48 package Four I/O modes: Quasi bi-direction -7- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet z z z z Push-Pull output Open-Drain output Input only with high impendence TTL/Schmitt trigger input selectable I/O pin can be configured as interrupt source with edge/level setting Supports high driver and high sink IO mode Timer Provides four channel 32-bit timers, one 8-bit pre-scale counter with 24-bit up-timer for each timer. Independent clock source for each timer. 24-bit timer value is readable through TDR (Timer Data Register) Provides one-shot, periodic and toggle operation modes. Watchdog Timer Multiple clock sources Supports wake-up from power down or idle mode Interrupt or reset selectable on watchdog time-out PWM Built-in up to four 16-bit PWM generators; providing eight PWM outputs or four complementary paired PWM outputs Individual clock source, clock divider, 8-bit pre-scalar and dead-zone generator for each PWM generator PWM interrupt synchronized to PWM period 16-bit digital Capture timers (shared with PWM timers) with rising/falling capture inputs Supports capture interrupt UART Up to two sets of UART device -8- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet z z Programmable baud-rate generator Buffered receiver and transmitter, each with 15 bytes FIFO Optional flow control function (CTS and RTS) Supports IrDA(SIR) function Supports RS485 function SPI Up to two sets of SPI device. Supports master/slave mode Master mode clock rate up to 20 MHz, and slave mode clock rate up to 10 MHz Full duplex synchronous serial data transfer Variable length of transfer data from 1 to 32 bits MSB or LSB first data transfer Rx latching data can be either at rising edge or at falling edge of serial clock Tx sending data can be either at rising edge or at falling edge of serial clock Supports Byte suspend mode in 32-bit transmission I2C Supports master/slave mode Bidirectional data transfer between masters and slaves Multi-master bus (no central master). Arbitration between simultaneously transmitting masters without corruption of serial data on the bus Serial clock synchronization allows devices with different bit rates to communicate via one serial bus. Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial transfer. Programmable clocks allow versatile rate control. -9- Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet z z Supports multiple address recognition (four slave address with mask option) ADC 12-bit SAR ADC with 600k SPS Up to 8-ch single-ended input or 4-ch differential input Supports single mode/burst mode/single-cycle scan mode/continuous scan mode Each channel with an individual result register Supports conversion value monitoring (or comparison) for threshold voltage detection Conversion can be started either by software trigger or external pin trigger EBI (External Bus Interface) for external memory-mapped device access Accessible space: 64KB in 8-bit mode or 128KB in 16-bit mode Supports 8-bit/16-bit data width z In-System Programming (ISP) and In-Circuit Programming (ICP) z Brownout Detector z With 4 levels: 4.5V/3.8V/2.7V/2.2V Supports brownout interrupt and reset option LVR (Low Voltage Reset) Threshold voltage levels: 2.0V z Operating Temperature: -40~85 z Packages: Green package (RoHS) 48-pin LQFP, 33-pin QFN - 10 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 3 BLOCK DIAGRAM Figure 3-1 NuMicroTM M051 Series Block Diagram - 11 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 4 SELECTION TABLE NuMicro M051TM Series Selection Guide Part No. APROM RAM Data Flash Connectivity LDROM I/O ISP Timer PWM UART SPI ADC EBI Package ICP I2C M052LAN 8KB 4KB 4KB 4KB 40 4x32-bit 2 2 1 8 8x12-bit M052ZAN 8KB 4KB 4KB 4KB 24 4x32-bit 2 1 1 5 5x12-bit M054LAN 16KB 4KB 4KB 4KB 40 4x32-bit 2 2 1 8 8x12-bit M054ZAN 16KB 4KB 4KB 4KB 24 4x32-bit 2 1 1 5 5x12-bit v v v LQFP48 v QFN 33 v LQFP48 v QFN 33 Table 4-1 NuMicroTM M051 Series Product Selection Guide M0 5X - X X X CPU core ARM Cortex-M0 Temperature Part Number 52 : 54 : 8K Flash ROM 16K Flash ROM N : -40 ~ +85 E : -40 ~ +105 C : -40 ~ +105 Reserved Package L : LQFP 48 Z : QFN 33 Figure 4-1 NuMicro M051TM Naming Rule - 12 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 5 PIN CONFIGURATION 5.1 QFN 33 pin CTS1, P0.0 RTS1, P0.1 P2.2, PWM2 P2.3, PWM3 P2.4, PWM4 LDO_CAP VDD AVDD VSS XTAL1 AIN0, T2, P1.0 RXD1, AIN2, P1.2 XTAL2 P3.6, CKO TXD1, AIN3, P1.3 AIN4, P1.4 Figure 5-1 NuMicroTM M051 Series QFN33 Pin Diagram - 13 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 5.2 LQFP 48 pin Figure 5-2 NuMicroTM M051 Series LQFP-48 Pin Diagram - 14 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 5.3 Pin Description Pin number Alternate Function Symbol QFN33 LQFP48 Type 1 [1] Description 2 I CRYSTAL1: This is the input pin to the internal inverting amplifier. The system clock is from external crystal or resonator when FOSC[1:0] (CONFIG3[1:0]) are both logic 1 by default. 11 16 XTAL1 10 15 XTAL2 O CRYSTAL2: This is the output pin from the internal inverting amplifier. It emits the inverted signal of XTAL1. 27 41 VDD P POWER SUPPLY: operation. 17 VSS P GROUND: Digital Ground potential. 28 42 AVDD P POWER SUPPLY: Supply voltage Analog AVDD for operation. 4 6 AVSS P GROUND: Analog Ground potential. 13 18 LDO_C AP P (ST) Supply voltage Digital VDD for 12 33 LDO: LDO output pin Note: It needs to be connected with a 10uF capacitor. I (ST) RESET: /RST pin is a Schmitt trigger input pin for hardware device reset. A "Low" on this pin for 768 clock counter of Internal 22.1184 MHz high speed oscillator while the system clock is running will reset the device. /RST pin has an internal pull-up resistor allowing power-on reset by simply connecting an external capacitor to GND. 2 4 /RST 26 40 P0.0 CTS1 AD0 D, I/O 25 39 P0.1 RTS1 AD1 D, I/O PORT0: Port 0 is an 8-bit four mode output pin and two mode input. Its multifunction pins are for CTS1, RTS1, CTS0, RTS0, SPISS1, MOSI_1, MISO_1, and SPICLK1. NC 38 P0.2 CTS0 AD2 D, I/O P0 has an alternative function as AD[7:0] while external memory interface (EBI) is enabled. NC 37 P0.3 RTS0 AD3 D, I/O These pins which are SPISS1, MOSI_1, MISO_1, and SPICLK1 for the SPI function used. 24 35 P0.4 SPISS1 AD4 D, I/O CTS0/1: Clear to Send input pin for UART0/1 - 15 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Pin number Alternate Function Symbol QFN33 LQFP48 Type 1 2 [1] Description RTS0/1: Request to Send output pin for UART0/1 23 34 P0.5 MOSI_1 AD5 D, I/O 22 33 P0.6 MISO_1 AD6 D, I/O 21 32 P0.7 SPICLK1 AD7 D, I/O 29 43 P1.0 T2 AIN0 I/O NC 44 P1.1 T3 AIN1 I/O 30 45 P1.2 RXD1 AIN2 I/O 31 46 P1.3 TXD1 AIN3 I/O 32 47 P1.4 SPISS0 AIN4 I/O These pins which are SPISS0, MOSI_0, MISO_0, and SPICLK0 for the SPI function used. 1 1 P1.5 MOSI_0 AIN5 I/O These pins which are AIN0~AIN7for the 12 bits ADC function used. NC 2 P1.6 MISO_0 AIN6 I/O The RXD1/TXD1 pins are for UART1 function used. NC 3 P1.7 SPICLK0 AIN7 I/O NC 19 P2.0 PWM0 AD8 D, I/O NC 20 P2.1 PWM1 AD9 D, I/O 14 21 P2.2 PWM2 AD10 D, I/O 15 22 P2.3 PWM3 AD11 D, I/O 16 23 P2.4 PWM4 AD12 D, I/O 17 25 P2.5 PWM5 AD13 D, I/O 18 26 P2.6 PWM6 AD14 D, I/O NC 27 P2.7 PWM7 AD15 D, I/O 3 5 P3.0 RXD I/O 5 7 P3.1 TXD I/O PORT1: Port 1 is an 8-bit four mode output pin and two mode input. Its multifunction pins are for T2, T3, RXD1, TXD1, SPISS0, MOSI_0, MISO_0, and SPICLK0. T2: Timer2 external input - 16 - T3: Timer3 external input PORT2: Port 2 is an 8-bit four mode output pin and two mode input. It has an alternative function P2 has an alternative function as AD[15:8] while external memory interface (EBI) is enabled. These pins which are PWM0~PWM7 for the PWM function. PORT3: Port 3 is an 8-bit four mode output pin and two mode input. Its multifunction pins are for RXD, TXD, INT0 , Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Pin number Alternate Function Symbol QFN33 LQFP48 Type 1 2 INT0 STADC I/O I/O 6 8 P3.2 NC 9 P3.3 INT1 MCLK 7 10 P3.4 T0 SDA I/O 8 11 P3.5 T1 SCL I/O [1] Description INT1 , T0, T1, WR , and RD . T0: Timer0 external input T1: Timer1 external input The RXD/TXD pins are for UART0 function used. 2 The SDA/SCL pins are for I C function used. MCLK: EBI clock output pin. CKO: HCLK clock output The STADC pin is for ADC external trigger input. 9 13 P3.6 WR NC 14 P3.7 RD I/O NC 24 P4.0 PWM0 I/O NC 36 P4.1 PWM1 I/O NC 48 P4.2 PWM2 I/O NC 12 P4.3 PWM3 I/O NC 28 P4.4 /CS I/O ALE (Address Latch Enable) is used to enable the address latch that separates the address from the data on Port 0 and Port 2. NC 29 P4.5 ALE I/O The ICE_CLK/ICE_DAT pins are for JTAG-ICE function used. 19 30 P4.6 ICE_CLK I/O 20 31 P4.7 ICE_DAT I/O CKO I/O PORT4: Port 4 is an 8-bit four mode output pin and two mode input. Its multifunction pins are for /CS, ALE, ICE_CLK and ICE_DAT. /CS for EBI (External Bus Interface) used. PWM0-3 can be used from P4.0-P4.3 when EBI is active. Table 5-1 NuMicroTM M051 Series Pin Description [1] I/O type description. I: input, O: output, I/O: quasi bi-direction, D: open-drain, P: power pins, ST: Schmitt trigger. - 17 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6 FUNCTIONAL DESCRIPTION 6.1 ARM(R) CortexTM-M0 Core The CortexTM-M0 processor is a configurable, multistage, 32-bit RISC processor. It has an AMBA AHBLite interface and includes an NVIC component. It also has optional hardware debug functionality. The processor can execute Thumb code and is compatible with other Cortex-M profile processor. The profile supports two modes -Thread and Handler modes. Handler mode is entered as a result of an exception. An exception return can only be issued in Handler mode. Thread mode is entered on Reset, and can be entered as a result of an exception return. Figure 6-1 Functional Block Diagram The implemented device provides: A low gate count processor the features: The ARMv6-M Thumb(R) instruction set. Thumb-2 technology. ARMv6-M compliant 24-bit SysTick timer. A 32-bit hardware multiplier. The system interface supports little-endian data accesses. The ability to have deterministic, fixed-latency, interrupt handling. - 18 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Load/store-multiples and multicycle-multiplies that can be abandoned and restarted to facilitate rapid interrupt handling. C Application Binary Interface compliant exception model. This is the ARMv6-M, C Application Binary Interface(C-ABI) compliant exception model that enables the use of pure C functions as interrupt handlers. Low power sleep mode entry using Wait For Interrupt (WFI), Wait For Event(WFE) instructions, or the return from interrupt sleep-on-exit feature. NVIC features: 32 external interrupt inputs, each with four levels of priority. Dedicated non-Maskable Interrupt (NMI) input. Support for both level-sensitive and pulse-sensitive interrupt lines Wake-up Interrupt Controller (WIC), supports ultra-low power sleep mode. Debug support: Four hardware breakpoints. Two watchpoints. Program Counter Sampling Register (PCSR) for non-intrusive code profiling. Single step and vector catch capabilities. Bus interfaces: Single 32-bit AMBA-3 AHB-Lite system interface that provides simple integration to all system peripherals and memory. Single 32-bit slave port that supports the DAP (Debug Access Port). - 19 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.2 System Manager 6.2.1 Overview The following functions are included in system manager section 6.2.2 System Resets System Memory Map System management registers for Part Number ID, chip reset and on-chip module reset , multi-functional pin control System Timer (SysTick) Nested Vectored Interrupt Controller (NVIC) System Control registers System Reset The system reset includes one of the list below event occurs. For these reset event flags can be read by RSTRC register. 6.2.3 The Power-On Reset (POR) The low level on the /RESET pin Watchdog Time Out Reset (WDT) Low Voltage Reset (LVR) Brown-Out-Detected Reset (BOD) CPU Reset System Reset System Power Architecture In this device, the power architecture is divided into three segments. Analog power from AVDD and AVSS provides the power for analog module operation. Digital power from VDD and VSS supplies the power to the internal regulator which provides a fixed 2.5V power for digital operation and I/O pins. - 20 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet The outputs of internal voltage regulator, which is LDO, require an external capacitor which should be located close to the corresponding pin. The Figure 6-2 shows the power architecture of this device. NuMicro-M051 Power Architecture AVDD AVSS 12-bit SAR-ADC FLASH Low Voltage Reset Brown Out Detector Digital Logic (Timer/UART/I2C/SPI...) IRC 22.1184MHz & 10KHz Osc. LDO_CAP 2.5V POR25 PLL IO cell P0~P4 VSS VDD VSS POR50 5V to 2.5V LDO 10uF Figure 6-2 NuMicro M051TM Series Power Architecture Diagram - 21 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.2.4 Whole System Memory Map NuMicro M051TM series provides a 4G-byte address space. The memory locations assigned to each on-chip modules are shown in Table 6-1. The detailed register memory addressing and programming will be described in the following sections for individual on-chip peripherals. NuMicro M051TM series only supports little-endian data format. Address Space Token Modules 0x0000_0000 - 0x0000_FFFF FLASH_BA FLASH Memory Space (64KB) 0x2000_0000 - 0x2000_0FFF SRAM_BA SRAM Memory Space (4KB) Flash and SRAM Memory Space AHB Modules Space (0x5000_0000 - 0x501F_FFFF) 0x5000_0000 - 0x5000_01FF GCR_BA System Global Control Registers 0x5000_0200 - 0x5000_02FF CLK_BA Clock Control Registers 0x5000_0300 - 0x5000_03FF INT_BA Interrupt Multiplexer Control Registers 0x5000_4000 - 0x5000_7FFF GPIO_BA GPIO (P0~P4) Control Registers 0x5000_C000 - 0x5000_FFFF FMC_BA Flash Memory Control Registers 0x5001_0000 - 0x5001_3FFF EBI_CTL_BA EBI Control Registers (128KB) EBI Space (0x6000_0000 ~ 0x6001_FFFF) 0x6000_0000 - 0x6001_FFFF EBI_BA EBI Space APB Modules Space (0x4000_0000 ~ 0x400F_FFFF) 0x4000_4000 - 0x4000_7FFF WDT_BA Watch-Dog Timer Control Registers 0x4001_0000 - 0x4001_3FFF TMR01_BA Timer0/Timer1 Control Registers 0x4002_0000 - 0x4002_3FFF I2C_BA I C Interface Control Registers 0x4003_0000 - 0x4003_3FFF SPI0_BA SPI0 with master/slave function Control Registers 0x4003_4000 - 0x4003_7FFF SPI1_BA SPI1 with master/slave function Control Registers 0x4004_0000 - 0x4004_3FFF PWMA_BA PWM0/1/2/3 Control Registers 0x4005_0000 - 0x4005_3FFF UART0_BA UART0 Control Registers 2 - 22 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 0x400E_0000 - 0x400E_FFFF ADC_BA Analog-Digital-Converter (ADC) Control Registers 0x4011_0000 - 0x4011_3FFF TMR23_BA Timer2/Timer3 Control Registers 0x4014_0000 - 0x4014_3FFF PWMB_BA PWM4/5/6/7 Control Registers 0x4015_0000 - 0x4015_3FFF UART1_BA UART1 Control Registers System Control Space (0xE000_E000 ~ 0xE000_EFFF) 0xE000_E010 - 0xE000_E0FF SCS_BA System Timer Control Registers 0xE000_E100 - 0xE000_ECFF SCS_BA External Interrupt Controller Control Registers 0xE000_ED00 - 0xE000_ED8F SCS_BA System Control Registers Table 6-1 Address Space Assignments for On-Chip Modules - 23 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.2.5 Whole System Memory Mapping Table M052/54/58/516 4 GB 0xFFFF_FFFF Reserved | 0xE000_F000 System Control System Control System Timer Control 0xE000_E000 SCS_BA EBI_CTL_BA 0xE000_EFFF 0xE000_E000 0xE000_E00F Reserved | 0x6002_0000 EBI 0x6001_FFFF 0x6000_0000 0x5FFF_FFFF Reserved | 0x5020_0000 AHB Reserved AHB peripherals 0x501F_FFFF EBI Control 0x5001_0000 0x5000_0000 FMC 0x5000_C000 FLASH_BA 0x4FFF_FFFF GPIO Control 0x5000_4000 GPIO_BA Interrupt Multiplexer Control 0x5000_0300 INT_BA Clock Control 0x5000_0200 CLK_BA System Global Control 0x5000_0000 GCR_BA UART1 Control 0x4015_0000 UART1_BA 0x2000_1000 PWM4/5/6/7 Control 0x4014_0000 PWMB_BA 0x2000_0FFF Timer2/Timer3 Control 0x4011_0000 TMR23_BA ADC Control 0x400E_0000 ADC_BA UART0 Control 0x4005_0000 UART0_BA 0x2000_0000 PWM0/1/2/3 Control 0x4004_0000 PWMA_BA 0x1FFF_FFFF SPI1 Control 0x4003_4000 SPI1_BA SPI0 Control 0x4003_0000 SPI0_BA I2C Control 0x4002_0000 I2C_BA | 0x4020_0000 0x401F_FFFF APB 1 GB | 0x4000_0000 0x3FFF_FFFF Reserved 4 KB SRAM (M052/M054/M058/M0516) 0.5 GB Reserved | | APB peripherals 0x0001_0000 Timer0/Timer1 Control 0x4001_0000 TMR01_BA 64 KB on-chip Flash (M0516) 0x0000_FFFF WDT Control 0x4000_4000 WDT_BA 32 KB on-chip Flash (M058) 0x0000_7FFF 16 KB on-chip Flash (M054) 0 GB | 8 KB on-chip Flash (M052) 0x0000_3FFF 0x0000_1FFF 0x0000_0000 - 24 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.2.6 System Timer (SysTick) The Cortex-M0 includes an integrated system timer, SysTick. SysTick provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter can be used as a Real Time Operating System (RTOS) tick timer or as a simple counter. When system timer is enabled, it will count down from the value in the SysTick Current Value Register (SYST_CVR) to zero, and reload (wrap) to the value in the SysTick Reload Value Register (SYST_RVR) on the next clock edge, then decrement on subsequent clocks. When the counter transitions to zero, the COUNTFLAG status bit is set. The COUNTFLAG bit clears on reads. The SYST_CVR value is UNKNOWN on reset. Software should write to the register to clear it to zero before enabling the feature. This ensures the timer will count from the SYST_RVR value rather than an arbitrary value when it is enabled. If the SYST_RVR is zero, the timer will be maintained with a current value of zero after it is reloaded with this value. This mechanism can be used to disable the feature independently from the timer enable bit. For more detailed information, please refer to the documents "ARM(R) CortexTM-M0 Technical Reference Manual" and "ARM(R) v6-M Architecture Reference Manual". - 25 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.2.7 Nested Vectored Interrupt Controller (NVIC) Cortex-M0 provides an interrupt controller as an integral part of the exception mode, named as "Nested Vectored Interrupt Controller (NVIC)". It is closely coupled to the processor kernel and provides following features: z Nested and Vectored interrupt support z Automatic processor state saving and restoration z Dynamic priority changing z Reduced and deterministic interrupt latency The NVIC prioritizes and handles all supported exceptions. All exceptions are handled in "Handler Mode". This NVIC architecture supports 32 (IRQ[31:0]) discrete interrupts with 4 levels of priority. All of the interrupts and most of the system exceptions can be configured to different priority levels. When an interrupt occurs, the NVIC will compare the priority of the new interrupt to the current running one's priority. If the priority of the new interrupt is higher than the current one, the new interrupt handler will override the current handler. When any interrupts is accepted, the starting address of the interrupt service routine (ISR) is fetched from a vector table in memory. There is no need to determine which interrupt is accepted and branch to the starting address of the correlated ISR by software. While the starting address is fetched, NVIC will also automatically save processor state including the registers "PC, PSR, LR, R0~R3, R12" to the stack. At the end of the ISR, the NVIC will restore the mentioned registers from stack and resume the normal execution. Thus it will take less and deterministic time to process the interrupt request. The NVIC supports "Tail Chaining" which handles back-to-back interrupts efficiently without the overhead of states saving and restoration and therefore reduces delay time in switching to pending ISR at the end of current ISR. The NVIC also supports "Late Arrival" which improves the efficiency of concurrent ISRs. When a higher priority interrupt request occurs before the current ISR starts to execute (at the stage of state saving and starting address fetching), the NVIC will give priority to the higher one without delay penalty. Thus it advances the real-time capability. For more detailed information, please refer to the documents "ARM(R) CortexTM-M0 Technical Reference Manual" and "ARM(R) v6-M Architecture Reference Manual". - 26 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.3 Clock Controller 6.3.1 Overview The clock controller generates the clocks for the whole chip, including system clocks and all peripheral clocks. The clock controller also implements the power control function with the individually clock ON/OFF control, clock source selection and clock divider. The chip will not enter power down mode until CPU sets the power down enable bit (PWR_DOWN_EN) and Cortex-M0 core executes the WFI instruction. After that, chip enters power down mode and wait for wake-up interrupt source triggered to leave power down mode. In the power down mode, the clock controller turns off the external 4~24 MHz high speed crystal and internal 22.1184 MHz high speed oscillator to reduce the overall system power consumption. 6.3.2 Clock Generator Block Diagram The clock generator consists of 4 sources which list below: z One external 4~24 MHz high speed crystal z One internal 22.1184 MHz high speed oscillator z One programmable PLL FOUT(PLL source consists of external 4~24 MHz high speed crystal and internal 22.1184 MHz high speed oscillator) z One internal 10 kHz low speed oscillator - 27 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Figure 6-3 Whole Chip Clock generator block diagram - 28 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet XTL12M_EN(PWRCON[0]) 4~24M XT_IN External Crystal 4~24M PLL_SRC(PLLCON[19]) 0 XT_OUT PLL OSC22M_EN(PWRCON[2]) Internal OSC22M PLL FOUT 1 22.1184M 22.1184M OSC10K_EN(PWRCON[3]) OSC10K 10K 10K Figure 6-4 Clock generator block diagram - 29 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.3.3 System Clock and SysTick Clock The system clock has 4 clock sources which were generated from clock generator block. The clock source switch depends on the register HCLK_S(CLKSEL0[2:0]). The block diagram is shown in the Figure 6-5. HCLK_S (CLKSEL0[2:0]) 22.1184 MHz 10 kHz PLLFOUT Reserved Ext. Crystal 1xx 011 CPUCLK 010 HCLK 1/(HCLK_N+1) 001 HCLK_N (CLKDIV[3:0]) PCLK CPU AHB APB 000 CPU in Power Down Mode Figure 6-5 System Clock Block Diagram The clock source of SysTick in Cortex-M0 core can use CPU clock or external clock (SYST_CSR[2]). If using external clock, the SysTick clock (STCLK) has 4 clock sources. The clock source switch depends on the setting of the register STCLK_S (CLKSEL0[5:3]. The block diagram is shown in the Figure 6-6. Figure 6-6 SysTick clock Control Block Diagram - 30 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.3.4 AHB Clock Source Select HCLK EBI (External Bus Interface) EBI_EN (AHBCLK[3]) HCLK ISP (In System Programmer) ISP_EN (AHBCLK[2]) Figure 6-7 AHB Clock Source for HCLK - 31 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.3.5 Peripherals Clock Source Select The peripherals clock had different clock source switch setting which depends on the different peripheral. Please refer the CLKSEL1 and APBCLK register description in chapter 6.3.9. PCLK W a tc h D o g T im e r W D T _ E N (A P B C L K 1 [0 ]) T im e r 0 T M R 0 _ E N (A P B C L K 1 [2 ]) T im e r 1 T M R 1 _ E N (A P B C L K 1 [3 ]) T im e r 2 T M R 2 _ E N (A P B C L K 1 [4 ]) T im e r 3 T M R 3 _ E N (A P B C L K 1 [5 ]) F r e q u e n c y D iv id e r F D IV _ E N (A P B C L K 1 [6 ]) I2 C I2 C 0 _ E N (A P B C L K 1 [8 ]) S P I0 S P I0 _ E N (A P B C L K 1 [1 2 ]) S P I1 S P I1 _ E N (A P B C L K 1 [1 3 ]) UART0 U A R T 0 _ E N (A P B C L K 1 [1 6 ]) UART1 U A R T 1 _ E N (A P B C L K 1 [1 7 ]) PW M 01 P W M 0 1 _ E N (A P B C L K 1 [2 0 ]) PW M 23 P W M 2 3 _ E N (A P B C L K 1 [2 1 ]) PW M 45 P W M 4 5 _ E N (A P B C L K 1 [2 2 ]) PW M 67 P W M 6 7 _ E N (A P B C L K 1 [2 3 ]) Figure 6-8 Peripherals Clock Source Select for PCLK - 32 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.3.6 Power Down Mode Clock When chip enter into power down mode, most of clock sources, peripheral clocks and system clock will be disabled. Some of clock sources and peripherals clock are still active in power down mode. For theses clocks which still keep active list below: Clock Generator Internal 10 kHz low speed oscillator clock Peripherals Clock (When these IP adopt internal 10 kHz low speed oscillator as clock source) - 33 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.3.7 Frequency Divider Output This device is equipped a power-of-2 frequency divider which is composed by16 chained divideby-2 shift registers. One of the 16 shift register outputs selected by a sixteen to one multiplexer is reflected to P3.6. Therefore there are 16 options of power-of-2 divided clocks with the frequency from Fin/21 to Fin/217 where Fin is input clock frequency to the clock divider. The output formula is Fout = Fin/2(N+1), where Fin is the input clock frequency, Fout is the clock divider output frequency and N is the 4-bit value in FREQDIV.FSEL[3:0]. When write 1 to DIVIDER_EN (FRQDIV[4]), the chained counter starts to count. When write 0 to DIVIDER_EN (FRQDIV[4]), the chained counter continuously runs till divided clock reaches low state and stay in low state. CLKSEL2.FRQDIV_S[3:2] APBCLK.FRQDIV_EN[6] 22.1184M HCLK Ext. Crystal 11 FRQDIV_CLK 10 00 Figure 6-9 Clock Source of Frequency Divider FREQDIV.FDIV_EN[4] 0 to 1 16 chained divide-by-2 counter Reset Clock Divider FRQDIV_CLK 1/2 1/22 1/23 ...... 1/21 5 1/21 6 000 001 : : 110 111 16 to 1 MUX 10 P3_DOUT[6] FREQDIV.FSEL[3:0] P3.6/CLKO 00 P3_ALT[6] P3_MFP[6] Figure 6-10 Block Diagram of Frequency Divider - 34 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.4 General Purpose I/O 6.4.1 Overview There are 40 General Purpose I/O pins shared with special feature functions in this MCU. The 40 pins are arranged in 5 ports named with P0, P1, P2, P3 and P4. Each port equips maximum 8 pins. Each one of the 40 pins is independent and has the corresponding register bits to control the pin mode function and data The I/O type of each of I/O pins can be software configured individually as input, output, opendrain or quasi-bidirectional mode. After reset, the all pins of I/O type stay in quasi-bidirectional mode and port data register Px_DOUT[7:0] resets to 0x000_00FF. Each I/O pin equips a very weakly individual pull-up resistor which is about 110K~300K for VDD is from 5.0V to 2.5V. 6.4.1.1 Input Mode Explanation Set Px_PMD(PMDn[1:0]) to 00b the Px[n] pin is in Input mode and the I/O pin is in tri-state(high impedance) without output drive capability. The Px_PIN value reflects the status of the corresponding port pins. 6.4.1.2 Output Mode Explanation Set Px_PMD(PMDn[1:0]) to 01b the Px[n] pin is in Output mode and the I/O pin supports digital output function with source/sink current capability. The bit value in the corresponding bit [n] of Px_DOUT is driven on the pin. VDD P Port Pin Port Latch Data N Input Data Figure 6-11 Push-Pull Output - 35 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.4.1.3 Open-Drain Mode Explanation Set Px_PMD(PMDn[1:0]) to 10b the Px[n] pin is in Open-Drain mode and the I/O pin supports digital output function but only with sink current capability, an additional pull-up resister is needed for driving high state. If the bit value in the corresponding bit [n] of Px_DOUT is "0", the pin drive a "low" output on the pin. If the bit value in the corresponding bit [n] of Px_DOUT is "1", the pin output drives high that is controlled by the internal pull-up resistor or the external pull high resistor. Port Pin Port Latch Data N Input Data Figure 6-12 Open-Drain Output 6.4.1.4 Quasi-bidirectional Mode Explanation Set Px_PMD(PMDn[1:0]) to 11b the Px[n] pin is in Quasi-bidirectional mode and the I/O pin supports digital output and input function at the same time but the source current is only up to hundreds uA. Before the digital input function is performed the corresponding bit in Px_DOUT must be set to 1. The quasi-bidirectional output is common on the 80C51 and most of its derivatives. If the bit value in the corresponding bit [n] of Px_DOUT is "0", the pin drive a "low" output on the pin. If the bit value in the corresponding bit [n] of Px_DOUT is "1", the pin will check the pin value. If pin value is high, no action takes. If pin state is low, then pin will drive strong high with 2 clock cycles on the pin and then disable the strong output drive and then the pin status is control by internal pull-up resistor. Note that the source current capability in quasi-bidirectional mode is only about 200uA to 30uA for VDD is form 5.0V to 2.5V VDD 2 CPU Clock Delay P Strong P Very Weak P Weak Port Pin Port Latch Data N Input Data Figure 6-13 Quasi-bidirectional I/O Mode - 36 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.5 I2C Serial Interface Controller (Master/Slave) 6.5.1 Overview 2 I C is a two-wire, bi-directional serial bus that provides a simple and efficient method of data exchange between devices. The I2C standard is a true multi-master bus including collision detection and arbitration that prevents data corruption if two or more masters attempt to control the bus simultaneously. Data is transferred between a Master and a Slave synchronously to SCL on the SDA line on a byte-by-byte basis. Each data byte is 8 bits long. There is one SCL clock pulse for each data bit with the MSB being transmitted first. An acknowledge bit follows each transferred byte. Each bit is sampled during the high period of SCL; therefore, the SDA line may be changed only during the low period of SCL and must be held stable during the high period of SCL. A transition on the SDA line while SCL is high is interpreted as a command (START or STOP). Please refer to the Figure 6-14 for more detail I2C BUS Timing. STOP Repeated START START STOP SDA tBUF tLOW tr SCL tHD;STA tf tHIGH tHD;DAT tSU;DAT tSU;STA tSU;STO Figure 6-14 I2C Bus Timing The device's on-chip I2C provides the serial interface that meets the I2C bus standard mode specification. The I2C port handles byte transfers autonomously. To enable this port, the bit ENS1 in I2CON should be set to '1'. The I2C H/W interfaces to the I2C bus via two pins: SDA (serial data line) and SCL (serial clock line). Pull up resistor is needed on pin SDA and SCL for I2C operation as these are open drain pins. When the I/O pins are used as I2C port, user must set the pins function to I2C in advance. 6.5.2 Features The I2C bus uses two wires (SDA and SCL) to transfer information between devices connected to the bus. The main features of the bus are: Support Master and Slave mode Bidirectional data transfer between masters and slaves Multi-master bus (no central master) Arbitration between simultaneously transmitting masters without corruption of serial data on the bus - 37 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Serial clock synchronization allows devices with different bit rates to communicate via one serial bus Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial transfer Built-in a 14-bit time-out counter will request the I2C interrupt if the I2C bus hangs up and timer-out counter overflows. External pull-up are needed for high output Programmable clocks allow versatile rate control Supports 7-bit addressing mode I2C-bus controllers support multiple address recognition ( Four slave address with mask option) - 38 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.6 PWM Generator and Capture Timer 6.6.1 Overview NuMicro M051TM series has 2 sets of PWM group supports 4 sets of PWM Generators which can be configured as 8 independent PWM outputs, PWM0~PWM7, or as 4 complementary PWM pairs, (PWM0, PWM1), (PWM2, PWM3), (PWM4, PWM5) and (PWM6, PWM7) with 4 programmable dead-zone generators. Each PWM Generator has one 8-bit prescaler, one clock divider with 5 divided frequencies (1, 1/2, 1/4, 1/8, 1/16), two PWM Timers including two clock selectors, two 16-bit PWM downcounters for PWM period control, two 16-bit comparators for PWM duty control and one deadzone generator. The 4 sets of PWM Generators provide eight independent PWM interrupt flags which are set by hardware when the corresponding PWM period down counter reaches zero. Each PWM interrupt source with its corresponding enable bit can cause CPU to request PWM interrupt. The PWM generators can be configured as one-shot mode to produce only one PWM cycle signal or auto-reload mode to output PWM waveform continuously. When PCR.DZEN01 is set, PWM0 and PWM1 perform complementary PWM paired function; the paired PWM period, duty and dead-time are determined by PWM0 timer and Dead-zone generator 0. Similarly, the complementary PWM pairs of (PWM2, PWM3), (PWM4, PWM5) and (PWM6, PWM7) are controlled by PWM2, PWM4 and PWM6 timers and Dead-zone generator 2, 4 and 6, respectively. Refer to figures bellowed for the architecture of PWM Timers. To prevent PWM driving output pin with unsteady waveform, the 16-bit period down counter and 16-bit comparator are implemented with double buffer. When user writes data to counter/comparator buffer registers the updated value will be load into the 16-bit down counter/ comparator at the time down counter reaching zero. The double buffering feature avoids glitch at PWM outputs. When the 16-bit period down counter reaches zero, the interrupt request is generated. If PWMtimer is set as auto-reload mode, when the down counter reaches zero, it is reloaded with PWM Counter Register (CNRx) automatically then start decreasing, repeatedly. If the PWM-timer is set as one-shot mode, the down counter will stop and generate one interrupt request when it reaches zero. The value of PWM counter comparator is used for pulse high width modulation. The counter control logic changes the output to high level when down-counter value matches the value of compare register. The alternate feature of the PWM-timer is digital input Capture function. If Capture function is enabled the PWM output pin is switched as capture input mode. The Capture0 and PWM0 share one timer which is included in PWM 0; and the Capture1 and PWM1 share PWM1 timer, and etc. Therefore user must setup the PWM-timer before enable Capture feature. After capture feature is enabled, the capture always latched PWM-counter to Capture Rising Latch Register (CRLR) when input channel has a rising transition and latched PWM-counter to Capture Falling Latch Register (CFLR) when input channel has a falling transition. Capture channel 0 interrupt is programmable by setting CCR0.CRL_IE0[1] (Rising latch Interrupt enable) and - 39 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet CCR0.CFL_IE0[2]] (Falling latch Interrupt enable) to decide the condition of interrupt occur. Capture channel 1 has the same feature by setting CCR0.CRL_IE1[17] and CCR0.CFL_IE1[18]. And capture channel 0 to channel 3 on each group have the same feature by setting the corresponding control bits in CCR0 and CCR2. For each group, whenever Capture issues Interrupt 0/1/2/3, the PWM counter 0/1/2/3 will be reload at this moment. The maximum captured frequency that PWM can capture is confined by the capture interrupt latency. When capture interrupt occurred, software will do at least three steps, they are: Read PIIR to get interrupt source and Read CRLRx/CFLRx(x=0 and 3) to get capture value and finally write 1 to clear PIIR. If interrupt latency will take time T0 to finish, the capture signal mustn't transition during this interval (T0). In this case, the maximum capture frequency will be 1/T0. For example: HCLK = 50 MHz, PWM_CLK = 25 MHz, Interrupt latency is 900 ns So the maximum capture frequency will is 1/900ns 1000 kHz 6.6.2 Features 6.6.2.1 PWM function features: PWM group has two PWM generators. Each PWM generator supports one 8-bit prescaler, one clock divider, two PWM-timers (down counter), one dead-zone generator and two PWM outputs. Up to 16 bits resolution PWM Interrupt request synchronized with PWM period One-shot or Auto-reload mode PWM Up to 2 PWM group (PWMA/PWMB) to support 8 PWM channels 6.6.2.2 Capture Function Features: Timing control logic shared with PWM Generators 8 capture input channels shared with 8 PWM output channels Each channel supports one rising latch register (CRLR), one falling latch register (CFLR) and Capture interrupt flag (CAPIFx) - 40 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.7 Serial Peripheral Interface (SPI) Controller 6.7.1 Overview The Serial Peripheral Interface (SPI) is a synchronous serial data communication protocol which operates in full duplex mode. Devices communicate in master/slave mode with 4-wire bi-direction interface. NuMicro M051TM series contains up to two sets of SPI controller performing a serial-toparallel conversion on data received from a peripheral device, and a parallel-to-serial conversion on data transmitted to a peripheral device. Each set of SPI controller can be set as a master; it also can be configured as a slave device controlled by an off-chip master device. 6.7.2 Features z Up to two sets of SPI controller z Support master or slave mode operation z Configurable bit length up to 32 bits of a transfer word and configurable word numbers up to 2 of a transaction, so the maximum bit length is 64 bits for each data transfer z Provide burst mode operation, transmit/receive can be transferred up to two times word transaction in one transfer z Support MSB or LSB first transfer z Byte or word Suspend Mode z Variable output serial clock frequency in master mode z Support two programmable serial clock frequencies in master mode - 41 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.8 Timer Controller 6.8.1 Overview The timer controller includes four 32-bit timers, TIMER0~TIMER3, which allows user to easily implement a timer control for applications. The timer can perform functions like frequency measurement, interval measurement, clock generation, delay timing, and so on. The timer can generates an interrupt signal upon timeout, or provide the current value of count during operation. 6.8.2 Features 4 sets of 32-bit timers with 24-bit up-timer and one 8-bit pre-scale counter Independent clock source for each timer. 24-bit timer value is readable through TDR (Timer Data Register) Provides one-shot, periodic, toggle and continuous counting operation modes. Time out period = (Period of timer clock input) * (8-bit pre-scale counter + 1) * (24-bit TCMP) Maximum counting cycle time = (1 / T MHz) * (2^8) * (2^24), T is the period of timer clock - 42 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.9 Watchdog Timer (WDT) 6.9.1 Overview The purpose of Watchdog Timer is to perform a system reset when system runs into an unknown state. This prevents system from hanging for an infinite period of time. Besides, this Watchdog Timer supports another function to wakeup chip from power down mode. The watchdog timer includes an 18-bit free running counter with programmable time-out intervals. Table 6-2 show the watchdog timeout interval selection and Figure 6.9-1 shows the timing of watchdog interrupt signal and reset signal. Setting WTE (WDTCR [7]) enables the watchdog timer and the WDT counter starts counting up. When the counter reaches the selected time-out interval, Watchdog timer interrupt flag WTIF will be set immediately to request a WDT interrupt if the watchdog timer interrupt enable bit WTIE is set, in the meanwhile, a specified delay time (1024 * TWDT) follows the time-out event. User must set WTR (WDTCR [0]) (Watchdog timer reset) high to reset the 18-bit WDT counter to avoid chip from Watchdog timer reset before the delay time expires. WTR bit is cleared automatically by hardware after WDT counter is reset. There are eight time-out intervals with specific delay time which are selected by Watchdog timer interval select bits WTIS (WDTCR [10:8]). If the WDT counter has not been cleared after the specific delay time expires, the watchdog timer will set Watchdog Timer Reset Flag (WTRF) high and reset chip. This reset will last 63 WDT clocks (TRST) then chip restarts executing program from reset vector (0x0000 0000). WTRF will not be cleared by Watchdog reset. User may poll WTFR by software to recognize the reset source. WDT also provides wakeup function. When chip is powered down and the Watchdog Timer Wake-up Function Enable bit (WDTR[4]) is set, if the WDT counter reaches the specific time interval defined by WTIS (WDTCR [10:8]) , the chip is waken up from power down state. First example, if WTIS is set as 000, the specific time interval for chip to wake up from power down state is 24 * TWDT. When power down command is set by software, then, chip enters power down state. After 24 * TWDT time is elapsed, chip is waken up from power down state. Second example, if WTIS (WDTCR [10:8]) is set as 111, the specific time interval for chip to wake up from power down state is 218 * TWDT. If power down command is set by software, then, chip enters power down state. After 218 * TWDT time is elapsed, chip is waken up from power down state. Notice if WTRE (WDTCR [1]) is set to 1, after chip is waken up, software should chip the Watchdog Timer counter by setting WTR(WDTCR [0]) to 1 as soon as possible. Otherwise, if the Watchdog Timer counter is not cleared by setting WTR (WDTCR [0]) to 1 before time starting from waking up to software clearing Watchdog Timer counter is over 1024 * TWDT , the chip is reset by Watchdog Timer. WTIS 000 Timeout Interval Selection Interrupt Period WTR Timeout Interval (WDT_CLK=10 kHz) TTIS TINT MIN. TWTR ~ MAX. TWTR 2 * TWDT 4 1024 * TWDT 1.6 ms ~ 104 ms 6 1024 * TWDT 6.4 ms ~ 108.8 ms 8 1024 * TWDT 25.6 ms ~ 128 ms 10 1024 * TWDT 102.4 ms ~ 204.8 ms 12 1024 * TWDT 409.6 ms ~ 512 ms 001 2 * TWDT 010 2 * TWDT 011 2 * TWDT 100 2 * TWDT - 43 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 14 1024 * TWDT 1.6384 s ~ 1.7408 s 16 1024 * TWDT 6.5536 s ~ 6.656 s 18 1024 * TWDT 26.2144 s ~ 26.3168 s 101 2 * TWDT 110 2 * TWDT 111 2 * TWDT Table 6-2 Watchdog Timeout Interval Selection - 44 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Figure 6-15 Timing of Interrupt and Reset Signal - 45 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.9.2 Features 18-bit free running counter to avoid chip from Watchdog timer reset before the delay time expires. Selectable time-out interval (24 ~ 218) and the time out interval is 104 ms ~ 26.3168 s (if WDT_CLK = 10 kHz). Reset period = (1 / 10 kHz) * 63, if WDT_CLK = 10 kHz. - 46 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.10 UART Interface Controller NuMicro M051TM series provides up to two channels of Universal Asynchronous Receiver/Transmitters (UART). UART0~1 performs Normal Speed UART, and support flow control function. 6.10.1 Overview The Universal Asynchronous Receiver/Transmitter (UART) performs a serial-to-parallel conversion on data received from the peripheral, and a parallel-to-serial conversion on data transmitted from the CPU. The UART controller also supports IrDA SIR Function, and RS-485 mode functions. Each UART channel supports five types of interrupts including transmitter FIFO empty interrupt (INT_THRE), receiver threshold level reaching interrupt (INT_RDA), line status interrupt (parity error or framing error or break interrupt) (INT_RLS), receiver buffer time out interrupt (INT_TOUT), and MODEM/Wakeup status interrupt (INT_MODEM). Interrupt number 12 (vector number is 28) supports UART0 interrupt. Interrupt number 13 (vector number is 29) supports UART1 interrupt. Refer to Nested Vectored Interrupt Controller chapter for System Interrupt Map. The UART0~1 are equipped 15-bytes transmitter FIFO (TX_FIFO) and 15-bytes receiver FIFO (RX_FIFO). The CPU can read the status of the UART at any time during the operation. The reported status information includes the type and condition of the transfer operations being performed by the UART, as well as 3 error conditions (parity error, framing error, and break interrupt) probably occur while receiving data. The UART includes a programmable baud rate generator that is capable of dividing clock input by divisors to produce the serial clock that transmitter and receiver need. The baud rate equation is Baud Rate = UART_CLK / M * [BRD + 2], where M and BRD are defined in Baud Rate Divider Register (UA_BAUD). The Table 6-3 and Table 6-4 list the equations in the various conditions and the UART baud rate setting table. Mode DIV_X_EN DIV_X_ONE Divider X BRD Baud rate equation 0 0 0 B A UART_CLK / [16 * (A+2)] 1 1 0 B A UART_CLK / [(B+1) * (A+2)] , B must >= 8 2 1 1 Don't care A UART_CLK / (A+2), A must >=3 Table 6-3 UART Baud Rate Equation - 47 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet System clock = internal 22.1184 MHz high speed oscillator Baud rate Mode0 Mode1 Mode2 921600 x A=0,B=11 A=22 460800 A=1 A=1,B=15 A=2,B=11 A=46 230400 A=4 A=4,B=15 A=6,B=11 A=94 115200 A=10 A=10,B=15 A=14,B=11 A=190 57600 A=22 A=22,B=15 A=30,B=11 A=382 38400 A=34 A=62,B=8 A=46,B=11 A=34,B=15 A=574 19200 A=70 A=126,B=8 A=94,B=11 A=70,B=15 A=1150 9600 A=142 A=254,B=8 A=190,B=11 A=142,B=15 A=2302 4800 A=286 A=510,B=8 A=382,B=11 A=286,B=15 A=4606 Table 6-4 UART Baud Rate Setting Table The UART0 and UART1 controllers support auto-flow control function that uses two low-level signals, /CTS (clear-to-send) and /RTS (request-to-send), to control the flow of data transfer between the UART and external devices (ex: Modem). When auto-flow is enabled, the UART is not allowed to receive data until the UART asserts /RTS to external device. When the number of bytes in the RX FIFO equals the value of RTS_TRI_LEV (UA_FCR [19:16]), the /RTS is deasserted. The UART sends data out when UART controller detects /CTS is asserted from external device. If a valid asserted /CTS is not detected the UART controller will not send data out. The UART controllers also provides Serial IrDA (SIR, Serial Infrared) function (User must set IrDA_EN (UA_FUN_SEL[1:0]) to enable IrDA function). The SIR specification defines a shortrange infrared asynchronous serial transmission mode with one start bit, 8 data bits, and 1 stop bit. The maximum data rate is 115.2 Kbps (half duplex). The IrDA SIR block contains an IrDA SIR Protocol encoder/decoder. The IrDA SIR protocol is half-duplex only. So it cannot transmit and receive data at the same time. The IrDA SIR physical layer specifies a minimum 10ms transfer delay between transmission and reception. This delay feature must be implemented by software. - 48 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Another alternate function of UART controllers is RS-485 9 bit mode function, and direction control provided by RTS pin or can program GPIO (P0.3 for RTS0 and P0.1 for RTS 1) to implement the function by software. The RS-485 mode is selected by setting the UA_FUN_SEL register to select RS-485 function. The RS-485 driver control is implemented using the RTS control signal from an asynchronous serial port to enable the RS-485 driver. In RS-485 mode, many characteristics of the RX and TX are same as UART. - 49 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.10.2 Features Full duplex, asynchronous communications Separate receive / transmit 15 bytes (UART0/UART1) entry FIFO for data payloads Support hardware auto flow control/flow control function (CTS, RTS) and programmable RTS flow control trigger level (UART0 and UART1 support) Programmable receiver buffer trigger level Support programmable baud-rate generator for each channel individually Support CTS wake up function (UART0 and UART1 support) Support 7 bit receiver buffer time out detection function Programmable transmitting data delay time between the last stop and the next start bit by setting UA_TOR [DLY] register Support break error, frame error, and parity error detect function Fully programmable serial-interface characteristics Programmable number of data bit, 5, 6, 7, 8 bit character Programmable parity bit, even, odd, no parity or stick parity bit generation and detection Programmable stop bit, 1, 1.5, or 2 stop bit generation Support IrDA SIR function mode Support for 3/16 bit duration for normal mode Support RS-485 function mode. Support RS-485 9bit mode Support hardware or software direct enable control provided by RTS pin - 50 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.11 Analog-to-Digital Converter (ADC) 6.11.1 Overview NuMicro M051TM series contain one 12-bit successive approximation analog-to-digital converters (SAR A/D converter) with 8 input channels. The A/D converter supports four operation modes: single, burst, single-cycle scan and continuous scan mode. The A/D converters can be started by software and external STADC/P3.2 pin. 6.11.2 Features Analog input voltage range: 0~AVDD (Max to 5.0V). 12-bit resolution and 10-bit accuracy is guaranteed. Up to 8 single-end analog input channels or 4 differential analog input channels. Maximum ADC clock frequency is 16 MHz. Up to 600k SPS conversion rate. Four operating modes - Single mode: A/D conversion is performed one time on a specified channel. - Single-cycle scan mode: A/D conversion is performed one cycle on all specified channels with the sequence from the lowest numbered channel to the highest numbered channel. - Continuous scan mode: A/D converter continuously performs Single-cycle scan mode until software stops A/D conversion. - Burst mode: A/D conversion will sample and convert the specified single channel and sequentially store in FIFO. An A/D conversion can be started by - Software Write 1 to ADST bit - External pin STADC Conversion results are held in data registers for each channel with valid and overrun indicators. Conversion result can be compared with specify value and user can select whether to generate an interrupt when conversion result matches the compare register setting. - 51 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Channel 7 supports 2 input sources: external analog voltage and internal bandgap voltage. Support Self-calibration to minimize conversion error. - 52 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.12 External Bus Interface (EBI) 6.12.1 Overview NuMicro M051TM series equips an external bus interface (EBI) for external device used. To save the connections between external device and this chip, EBI support address bus and data bus multiplex mode. And, address latch enable (ALE) signal supported differentiate the address and data cycle. 6.12.2 Features External Bus Interface has the following functions: 1. External devices with max. 64K-byte size (8 bit data width)/128K-byte (16 bit data width) supported 2. Variable external bus base clock (MCLK) supported 3. 8 bit or 16 bit data width supported 4. Variable data access time (tACC), address latch enable time (tALE) and address hold time (tAHD) supported 5. Address bus and data bus multiplex mode supported to save the address pins 6. Configurable idle cycle supported for different access condition: Write command finish (W2X), Read-to-Read (R2R) - 53 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 6.13 Flash Memory Controller (FMC) 6.13.1 Overview NuMicro M051TM series equips with 64K/32K/16K/8K bytes on chip embedded Flash for application program memory (APROM) that can be updated through ISP/IAP procedure. In System Programming (ISP) function enables user to update program memory when chip is soldered on PCB. After chip power on Cortex-M0 CPU fetches code from APROM or LDROM decided by boot select (CBS) in Config0. By the way, NuMicro M051TM series also provide additional 4K bytes DATA Flash for user to store some application depended data before chip power off in 64/32/16/8K bytes APROM model. 6.13.2 Features Run up to 50 MHz with zero wait state for continuous address read access 64/32/16/8KB application program memory (APROM) 4KB in system programming (ISP) loader program memory (LDROM) Fixed 4KB data flash with 512 bytes page erase unit In System Program (ISP)/In Application Program (IAP) to update on chip Flash In Circuit Program (ICP) via serial wire debug interface (SWD) - 54 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet TYPICAL APPLICATION CIRCUIT DVDD DVDD DVDD LE OE L2 FB AVDD R1 10K ALE 11 1 D0 D1 D2 D3 D4 D5 D6 D7 U2 74F373 2 5 6 9 12 15 16 19 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 C1 10uF/10V AA8 AA9 AA10 AA11 AA12 AA13 AA14 AA15 TANT-A LE OE D VSS 3 4 7 8 13 14 17 18 AVSS 20 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 VC C AA0 AA1 AA2 AA3 AA4 AA5 AA6 AA7 FB CB3 0.1 uF Reset Circuit CB4 0.1 uF C2 20p 10 11 1 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 2 5 6 9 12 15 16 19 L1 nTICERST CB2 0.1 uF U1 74F373 20 ALE D0 D1 D2 D3 D4 D5 D6 D7 VC C 3 4 7 8 13 14 17 18 GND AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND CB1 0.1 uF DVDD 10 D12MO ADC CB6 0.1 uF A4 A3 A2 A1 A0 CS I/O0 I/O1 I/O2 I/O3 VCC VSS I/O4 I/O5 I/O6 I/O7 WE A17 A16 A15 A14 A13 A5 A6 A7 OE UB LB I/O15 I/O14 I/O13 I/O12 VSS VCC I/O11 I/O10 I/O9 I/O8 NC A8 A9 A10 A11 A12 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 AA5 AA6 AA7 nRD AD15 AD14 AD13 AD12 DVSS DVDD AD11 AD10 AD9 AD8 ADC Input 1 2 CON1 1X2 HEADER P11 RXD1 TXD1 nSS0 P42 C3 820pF 1 2 U4 M052_LQFP_48 AVD D D VD D U3 CB5 0.1 uF MOSI_0 MISO_0 SCLK0 nTICERST RXD0 AVSS TXD0 P32 P33 SDA SCL P43 AA8 AA9 AA10 AA11 AA12 MOSI_0/AIN5/P1.5 MISO_0/AIN6/P1.6 SCLK0/AIN7/P1.7 RST RXD/P3.0 AVSS TXD/P3.1 INT0/P3.2 MCLK/INT1/P3.3 SDA/T0/P3.4 SCL/T1/P3.5 P4.3 EBI XTAL3-1 D12MI Crystal ICEJP1 P4.1 P0.4/AD4/SS1 P0.5/AD5/MOSI_1 P0.6/AD6/MISO_1 M052_54 LQFP 48 P0.7/AD7/SCLK1 P4.7/ICE_DAT P4.6/ICE_CLK P4.5/ALE P4.4/CS P2.7/AD15/PWM7 P2.6/AD14/PWM6 P2.5/AD13/PWM5 36 35 34 33 32 31 30 29 28 27 26 25 1 3 5 7 9 P41 AD4 AD5 AD6 AD7 TICEDAT TICECLK ALE nCS AD15 AD14 AD13 2 4 6 8 10 TICEDAT TICECLK nTICERST HEADER 5X2 HEADER5X2 ICE Interface P 3.6/W R /C K O P 3.7/R D XT AL2 XT AL1 VSS LD O _C AP P 2.0/A D 8/P W M 0 P 2.1/A D 9/P W M 1 P 2.2/A D 10/P W M 2 P 2.3/A D 11/P W M 3 P 2.4/A D 12/P W M 4 P 4.0 BS616LV4017EG70(TSOP-44) 1 2 3 4 5 6 7 8 9 10 11 12 C4 20p AD0 AD1 AD2 AD3 48 47 46 45 44 43 42 41 40 39 38 37 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 P4.2 AIN 3/S S0/P 1.4 A IN 3/T X D 1/P1.3 AIN 2/R X D 1/P1.2 A IN 1/T 2/P1.1 A IN 0/T 2/P1.0 AVD D VD D P0.0/AD 0/C T S1 P0.1/AD 1/R T S1 P0.2/AD 2/C T S0 P0.3/AD 3/R T S0 AA4 AA3 AA2 AA1 AA0 nCS AD0 AD1 AD2 AD3 DVDD DVSS AD4 AD5 AD6 AD7 nWR DVSS DVSS AA15 AA14 AA13 X1 12MHz SPI 13 14 15 16 17 18 19 20 21 22 23 24 7 nWR nRD D12MO D12MI 1 2 3 4 UART_RXD UART_TXD S1 8 7 6 5 P40 AD12 AD11 AD10 AD9 AD8 RXD0 TXD0 RXD1 TXD1 DVDD DVDD CB7 0.1 uF C5 10uF TANT-B SW DIP-4 SWDIP8 RSPI1 4.7K nSS1 MISO_1 MET22 1 2 3 4 RSPI2 4.7K USPI1 W25X16VSSIG CS# DO WP# GND VCC HOLD# CLK DI 8 7 6 5 DVDD MET23 SCLK1 MOSI_1 SOIC-8P UART C6 1uF TANT-A P1 11 VSS 1 6 2 7 3 8 4 9 5 10 DB9-M () DB9L-HP VDD C8 1uF TANT-A NET10 NET11 R3 33 R5 33 C7 1uF TANT-A NET3 NET4 NET40 NET5 NET6 NET7 NET8 NET9 C9 1uF TANT-A I2C DVDD 1 2 3 4 5 6 7 8 U5 MAX232A C1+ V+ C1C2+ C2VT2OUT R2IN SOP16/150 VCC GND T1OUT R1IN R1OUT T1IN T2IN R2OUT 16 15 14 13 12 11 10 9 CB8 0.1 uF DVDD NET12 NET13 R4 33 EEPROM ADDRESS:0H UART_TXD UART_RXD R6 33 1 2 3 4 I2C-EEPROM UI2C1 A0 A1 A2 GND VCC WP SCL SDA RI2C1 4.7K 8 7 6 5 24LC64 SOIC8\1.27\5.6MM - 55 - RI2C2 4.7K CB9 0.1 uF Title SCL SDA M052_54 Application Circuit Size Document Number Date: Thursday , August 19, 2010 Rev Application.dsn 1.0 Sheet 1 of 1 Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8 ELECTRICAL CHARACTERISTICS 8.1 Absolute Maximum Ratings SYMBOL PARAMETER MIN MAX UNIT VDD-VSS -0.3 +7.0 V VIN VSS-0.3 VDD+0.3 V 1/tCLCL 0 40 MHz TA -40 +85 C TST -55 +150 C - 120 mA Maximum Current out of VSS 120 mA Maximum Current sunk by a I/O pin 35 mA Maximum Current sourced by a I/O pin 35 mA Maximum Current sunk by total I/O pins 100 mA Maximum Current sourced by total I/O pins 100 mA DC Power Supply Input Voltage Oscillator Frequency Operating Temperature Storage Temperature Maximum Current into VDD Note: Exposure to conditions beyond those listed under absolute maximum ratings may adversely affects the lift and reliability of the device. - 56 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.2 DC Electrical Characteristics (VDD-VSS=2.5~5.5V, TA = 25C, FOSC = 50 MHz unless otherwise specified.) SPECIFICATION PARAMETER SYM. TEST CONDITIONS MIN. TYP. MAX. UNIT 5.5 V Operation voltage VDD 2.5 Power Ground VSS AVSS -0.3 LDO Output Voltage VLDO -10% 2.45 +10% V VDD > 2.7V Band Gap Analog Input VBG -5% 1.26 +5% V VDD =2.5V ~ 5.5V AVDD 0 VDD V Analog Operating Voltage Operating Current Normal Run Mode @ 50 MHz Operating Current Normal Run Mode @ 12 MHz Operating Current Normal Run Mode @ 4 MHz Operating Current VDD =2.5V ~ 5.5V up to 50 MHz V IDD1 32 mA VDD= 5.5V@50 MHz, enable all IP and PLL, XTAL=12 MHz IDD2 24 mA VDD=5.5V@50 MHz, disable all IP and enable PLL, XTAL=12 MHz IDD3 31 mA VDD = 3V@50 MHz, enable all IP and PLL, XTAL=12 MHz IDD4 23 mA VDD = 3V@50 MHz, disable all IP and enable PLL, XTAL=12 MHz IDD5 17 mA VDD = 5.5V@ 12MHz, enable all IP and disable PLL, XTAL=12 MHz IDD6 14 mA VDD = 5.5V@12 MHz, disable all IP and disable PLL, XTAL=12 MHz IDD7 16 mA VDD = 3V@12 MHz, enable all IP and disable PLL, XTAL=12 MHz IDD8 13 mA VDD = 3V@12 MHz, disable all IP and disable PLL, XTAL=12 MHz IDD9 12 mA VDD = 5.5V@4 MHz, enable all IP and disable PLL, XTAL=4MHz IDD10 10 mA VDD = 5.5V@4 MHz, disable all IP and disable PLL, XTAL=4MHz IDD11 10 mA VDD = 3V@4 MHz, enable all IP and disable PLL, XTAL=4MHz IDD12 9 mA VDD = 3V@4 MHz, disable all IP and disable PLL, XTAL=4 MHz IIDLE1 19 mA VDD= 5.5V@50 MHz, enable all IP and PLL, XTAL=12 MHz - 57 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Idle Mode @ 50 MHz IIDLE2 11 mA VDD=5.5V@50 MHz, disable all IP and enable PLL, XTAL=12 MHz IIDLE3 18 mA VDD = 3V@50 MHz, enable all IP and PLL, XTAL=12 MHz IIDLE4 10 mA VDD = 3V@50 MHz, disable all IP and enable PLL, XTAL=12 MHz IIDLE5 10 mA VDD = 5.5V@12 MHz, enable all IP and disable PLL, XTAL=12 MHz IIDLE6 7 mA VDD = 5.5V@12 MHz, disable all IP and disable PLL, XTAL=12 MHz IIDLE7 9 mA VDD = 3V@12 MHz, enable all IP and disable PLL, XTAL=12 MHz IIDLE8 6 mA VDD = 3V@12 MHz, disable all IP and disable PLL, XTAL=12 MHz IIDLE9 5 mA VDD = 5.5V@4 MHz, enable all IP and disable PLL, XTAL=4 MHz IIDLE10 4 mA VDD = 5.5V@4 MHz, disable all IP and disable PLL, XTAL=4 MHz IIDLE11 4 mA VDD = 3V@4 MHz, enable all IP and disable PLL, XTAL=4 MHz IIDLE12 3 mA VDD = 3V@4 MHz, disable all IP and disable PLL, XTAL=4 MHz IPWD1 15 A VDD = 5.5V, No load @ Disable BOV function IPWD2 11 A VDD = 3.0V, No load @ Disable BOV function Input Current P0/1/2/3/4 (Quasi-bidirectional mode) IIN1 -50 -60 A VDD = 5.5V, VIN = 0.4V Input Leakage Current P0/1/2/3/4 ILK -2 - +2 A VDD = 5.5V, 0<VIN<VDD -650 - -200 A VDD = 5.5V, VIN<2.0V -0.3 - 0.8 -0.3 - 0.6 2.0 - VDD +0.2 Operating Current Idle Mode @ 12 MHz Operating Current Idle Mode @ 4 MHz Standby Current Power down Mode Logic 1 to 0 Transition Current P0/1/2/3/4 (Quasi-bidiretional mode) ITL Input Low Voltage P0/1/2/3/4 (TTL input) VIL1 Input High Voltage P0/1/2/3/4 (TTL input) VIH1 Input Low Voltage XT1 1.5 [*2] Input High Voltage [*2] XT1 Negative going threshold (Schmitt input), /RST [3] VIL3 - 0 - 0.8 0 - 0.4 3.5 - VDD +0.2 2.4 - VDD +0.2 -0.5 - 0.3VDD VIH3 VILS VDD +0.2 - 58 - V VDD = 4.5V VDD = 2.5V VDD = 5.5V V VDD =3.0V V VDD = 4.5V VDD = 3.0V V VDD = 5.5V VDD = 3.0V V Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Positive going threshold VDD+0. 5 V 150 K - 0.2VDD V 0.4VDD - VDD +0.5 V ISR11 -300 -370 -450 A VDD = 4.5V, VS = 2.4V ISR12 -50 -70 -90 A VDD = 2.7V, VS = 2.2V ISR12 -40 -60 -80 A VDD = 2.5V, VS = 2.0V ISR21 -20 -24 -28 mA VDD = 4.5V, VS = 2.4V ISR22 -4 -6 -8 mA VDD = 2.7V, VS = 2.2V ISR22 -3 -5 -7 mA VDD = 2.5V, VS = 2.0V ISK1 10 16 20 mA VDD = 4.5V, VS = 0.45V ISK1 7 10 13 mA VDD = 2.7V, VS = 0.45V ISK1 6 9 12 mA VDD = 2.5V, VS = 0.45V Brownout voltage with BOV_VL [1:0] =00b VBO2.2 2.1 2.2 2.3 V Brownout voltage with BOV_VL [1:0] =01b VBO2.7 2.6 2.7 2.8 V Brownout voltage with BOV_VL [1:0] =10b VBO3.8 3.7 3.8 3.9 V Brownout voltage with BOV_VL [1:0] =11b VBO4.5 4.4 4.5 4.6 V VBH 30 - 150 mV (Schmitt input), /RST Internal /RST pin pull up resistor VIHS 0.7VDD RRST 40 VILS -0.5 VIHS - Negative going threshold (Schmitt P0/1/2/3/4 input), Positive going threshold (Schmitt P0/1/2/3/4 input), Source Current P0/1/2/3/4 (Quasibidirectional Mode) Source Current P0/1/2/3/4 (Push-pull Mode) Sink Current P0/1/2/3/4 (Quasi-bidirectional and Push-pull Mode) Hysteresis range of BOD voltage VDD = 2.5V~5.5V Notes: 1. /RST pin is a Schmitt trigger input. 2. XTAL1 is a CMOS input. 3. Pins of P0, P1, P2, P3 and P4 can source a transition current when they are being externally driven from 1 to 0. In the condition of VDD=5.5V, 5he transition current reaches its maximum value when Vin approximates to 2V . - 59 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.3 AC Electrical Characteristics 8.3.1 External 4~24 MHz High Speed Crystal Note: Duty cycle is 50%. PARAMETER SYMBOL MIN. TYP. MAX. UNITS Clock High Time tCHCX 20 - 125 nS Clock Low Time tCLCX 20 - 125 nS Clock Rise Time tCLCH - - 10 nS Clock Fall Time tCHCL - - 10 nS 8.3.2 CONDITION External 4~24 MHz High Speed Oscillator PARAMETER CONDITION MIN. TYP. MAX. UNIT Input clock frequency External crystal 4 12 24 MHz Temperature - -40 - 85 VDD - 2.5 5 5.5 V Operating current 12 MHz@ VDD = 5V - 5 - mA - 60 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.3.3 Typical Crystal Application Circuits CRYSTAL C1 C2 Optional 4 MHz ~ 24 MHz (Depend on crystal specification) Figure 8-1 Typical Crystal Application Circuit - 61 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.3.4 Internal 22.1184 MHz High Speed Oscillator PARAMETER Supply voltage CONDITION MIN. TYP. MAX. UNIT - 2.5 - 5.5 V - - 22.1184 [1] Center Frequency C; VDD =5V -1 - +1 % -40 C~+85 C; VDD=2.5V~5.5V -3 - +3 % Accuracy of Un-calibrated Internal Oscillator Frequency -40 C~+85 C; VDD=2.5V~5.5V -25 - +25 % Operating current VDD =5V - 500 - uA CONDITION MIN. TYP. MAX. UNIT - 2.5 - 5.5 V Calibrated Internal Oscillator Frequency 8.3.5 +25 MHz Internal 10 kHz Low Speed Oscillator PARAMETER Supply voltage [1] Center Frequency Calibrated Internal Oscillator Frequency - 10 - kHz C; VDD =5V - -30 - +30 % -40 C~+85 C; VDD=2.5V~5.5V -50 - +50 % VDD =5V - 5 - uA +25 Operating current Notes: 1. Internal operation voltage comes form LDO. - 62 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.4 Analog Characteristics 8.4.1 Specification of 600 kHz sps 12-bit SARADC PARAMETER SYM. MIN. TYP. MAX. UNIT Resolution - - - 12 Bit Differential nonlinearity error DNL - 1.2 - LSB Integral nonlinearity error INL - 1.5 - LSB Offset error EO - +4 10 LSB Gain error (Transfer gain) EG - +7 1.005 - Monotonic - Guaranteed - ADC clock frequency FADC - - 20 MHz Calibration time TCAL - 127 - Clock Sample time TS - 7 - Clock Conversion time TADC - 13 - Clock Sample rate FS - - 600 k sps VLDO - 2.5 - V VADD 3 - 5.5 V IDD - 0.5 - mA IDDA - 1.5 - mA Input voltage range VIN 0 - AVDD V Capacitance CIN - 5 - pF Supply voltage Supply current (Avg.) - 63 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.4.2 Specification of LDO and Power management PARAMETER MIN TYP MAX UNIT NOTE Input Voltage 2.7 5 5.5 V VDD input voltage Output Voltage -10% 2.5 +10% V VDD > 2.7V Temperature -40 25 85 - 100 - uA - 5 - uA Iload (PD=0) - - 100 mA Iload (PD=1) - - 100 uA Cbp - 10 - uF Quiescent Current (PD=0) Quiescent Current (PD=1) Resr=1ohm Note: 1. It is recommended that a 10uF (or higher) capacitor and a 100nF bypass capacitor are connected between VDD and the closest VSS pin of the device. 2. For ensuring power stability, a 4.7uF or higher capacitor must be connected between LDO pin and the closest VSS pin of the device. - 64 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.4.3 Specification of Low Voltage Reset PARAMETER CONDITION MIN. TYP. MAX. UNIT Operation voltage - 1.7 - 5.5 V Quiescent current VDD5V=5.5V - - 5 uA Temperature=25 1.7 2.0 2.3 V Temperature=-40 - 2.4 - V Temperature=85 - 1.6 - V - 0 0 0 V Threshold voltage Hysteresis 8.4.4 Specification of Brownout Detector PARAMETER CONDITION MIN. TYP. MAX. UNIT Operation voltage - 2.5 - 5.5 V Quiescent current AVDD=5.5V - - 125 A Temperature - -40 25 85 BOV_VL[1:0]=11 4.4 4.5 4.6 V BOV_VL [1:0]=10 3.7 3.8 3.9 V BOV_VL [1:0]=01 2.6 2.7 2.8 V BOV_VL [1:0]=00 2.1 2.2 2.3 V - 30m - 150m V Brown-out voltage Hysteresis 8.4.5 Specification of Power-On Reset (5V) PARAMETER CONDITION MIN. TYP. MAX. UNIT Reset voltage V+ - 2 - V Quiescent current Vin>reset voltage - 1 - nA - 65 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 8.5 SPI Dynamic characteristics PARAMETER CONDITION MIN. TYP. MAX. UNIT SPI master mode (VDD = 4.5V ~ 5.5V, 30pF loading Capacitor) tDS Data setup time 26 - - ns tDH Data hold time 0 - - ns tV Data output valid time - - 6 ns SPI master mode (VDD = 3.0V ~ 3.6V, 30pF loading Capacitor) tDS Data setup time 39 - - ns tDH Data hold time 0 - - ns tV Data output valid time - - 10 ns SPI slave mode (VDD = 4.5V ~ 5.5V, 30pF loading Capacitor) tDS Data setup time 0 - - ns tDH Data hold time 2*PCLK+4 - - ns tV Data output valid time - - 2*PCLK+27 ns SPI slave mode (VDD = 3.0V ~ 3.6V, 30pF loading Capacitor) tDS Data setup time 0 - - ns tDH Data hold time 2*PCLK+8 - - ns tV Data output valid time - - 2*PCLK+40 ns - 66 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Figure 8-2 SPI Master timing Figure 8-3 SPI Slave timing - 67 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 9 PACKAGE DIMENSIONS 9.1 LQFP-48 (7x7x1.4mm2 Footprint 2.0mm) - 68 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 9.2 QFN-33 (5X5 mm2, Thickness 0.8mm, Pitch 0.5 mm) - 69 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet 10 REVISION HISTORY VERSION DATE PAGE V1.0 Mar 15, 2011 - V2.0 May 30, 2011 DESCRIPTION Initial issued Page 28 Add "Whole Chip Clock generator block diagram" Page 64 Revise the spec of LDO Page 66 Add SPI Dynamic Characteristics - 70 - Publication Release Date: May 30, 2011 Revision V2.00 NuMicroTM M052/M054 Data Sheet Important Notice Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any malfunction or failure of which may cause loss of human life, bodily injury or severe property damage. Such applications are deemed, "Insecure Usage". Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and other applications intended to support or sustain life. All Insecure Usage shall be made at customer's risk, and in the event that third parties lay claims to Nuvoton as a result of customer's Insecure Usage, customer shall indemnify the damages and liabilities thus incurred by Nuvoton. - 71 - Publication Release Date: May 30, 2011 Revision V2.00