CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 1 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 Product Specification Applicant / Manufacturer Hardware Applicant / Manufacturer Software Panasonic Industrial Devices Europe GmbH Zeppelinstrasse 19 21337 Luneburg Germany Please refer to chapter 23 Ordering Information By purchase of any of products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required without notification POWER ELECTRONICS R&D CENTER WIRELESS CONNECTIVITY PANASONIC INDUSTRIAL DEVICES EUROPE GmbH APPROVED CHECKED DESIGNED CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 2 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Key Features................................................................................................................... 4 Applications for the Module............................................................................................. 4 Description for the Module .............................................................................................. 4 Scope of this Document .................................................................................................. 5 History for this Document................................................................................................ 5 Terminal Layout .............................................................................................................. 6 Block Diagram................................................................................................................. 8 7.1. PAN2580-868MHz................................................................................................. 8 7.2. PAN2580-915MHz................................................................................................. 8 Key Parts List .................................................................................................................. 9 Test Conditions ............................................................................................................... 9 Absolute Maximum Ratings ............................................................................................ 9 Operating Conditions .................................................................................................... 10 DC electrical characeristics........................................................................................... 10 A/D converter Characteristics ....................................................................................... 11 AC Electrical Characteristics......................................................................................... 12 Soldering Temperature - Time Profile for reflow soldering............................................ 13 15.1. For lead solder..................................................................................................... 13 15.2. For lead free solder.............................................................................................. 13 Module Dimensions....................................................................................................... 14 16.1. SMD Module PAN2580 / ENW59625xxxF........................................................... 14 16.2. Pin Header Module PAN2580ETU / ENW59635xxxF ......................................... 14 FootPrint of the Module................................................................................................. 15 17.1. SMD Module PAN2580 / ENW59625xxxF........................................................... 15 17.2. PIN HEADER MODULE PAN2580ETU / ENW59635xxxF .................................. 16 Recommended Land Pattern ........................................................................................ 17 18.1. SMD Module PAN2580 / ENW59625xxxF........................................................... 17 18.2. Pin Header Module PAN2580ETU / ENW59635xxxF ......................................... 18 Laser marking ............................................................................................................... 19 Reliability Tests ............................................................................................................. 20 Cautions ........................................................................................................................ 20 21.1. Design Notes ....................................................................................................... 20 21.2. Installation Notes ................................................................................................. 21 21.3. Usage Conditions Notes ...................................................................................... 21 21.4. Storage Notes...................................................................................................... 21 21.5. Safety Cautions ................................................................................................... 22 21.6. Other cautions ..................................................................................................... 22 Packaging of SMD Module PAN2580 ENW59625xxxF ............................................... 23 22.1. Tape Dimension................................................................................................... 23 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 3 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 23. 24. 25. 26. 27. 28. 29. 30. 31. 22.2. Packing in Tape ................................................................................................... 23 22.3. Component direction............................................................................................ 24 22.4. Reel Dimension ................................................................................................... 24 22.5. Label for Package................................................................................................ 25 22.6. Total Packing Handling........................................................................................ 26 22.7. Cover tape reel strength ...................................................................................... 26 Ordering Information ..................................................................................................... 27 RoHS Declaration ......................................................................................................... 28 Data Sheet Status ......................................................................................................... 28 Regulatory Information.................................................................................................. 28 26.1. FCC Notice .......................................................................................................... 28 26.2. Caution ................................................................................................................ 28 26.3. Labeling Requirements........................................................................................ 29 26.4. Antenna Warning ................................................................................................. 29 26.5. Approved Antenna List ........................................................................................ 29 26.6. RF Exposure PAN2580 ....................................................................................... 30 Industry Canada Certification........................................................................................ 30 European R&TTE Declaration of Conformity ................................................................ 30 Related Documents....................................................................................................... 31 General Information ...................................................................................................... 31 Life Support Policy ........................................................................................................ 32 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 4 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 1. KEY FEATURES * * * * * * * * * * * * * * * * Available as small size SMD device (29.8mm x 19.0mm x 2.7mm) or ETU (Easy to use) with pin header (33.9 x 33.9 x 7.3mm) 868MHz (Europe) or 915MHz (USA) 3 antenna options: Single port 50, ceramic antenna or plug 250 kbps RF raw data rate (150kbps with SNAP(R)) Low power modes for increased battery life High sensitivity: -97dBm typ. @ 150kbps & 1% Packet Error Rate +18 dBm @ 915MHz or +13 dBm @ 868 MHz max. Pout programmable over a 20 dB range Low supply voltage (2.7 V to 3.6 V, 3.0 V typ.) Operating temperature range -40C to +85C 192k total Flash with 64k used by SNAP(R) core, 64k free for uploadable SNAPpy scripts, and 64k reserved. 1 UART with HW Flow Control for control or transparent data 19 GPIOs and up to 18 A/D inputs with 10 Bit ADC for fast and easy conversion from analog inputs -such as temperature, pressure and fluid levels- to digital values. GFSK Modulation with FHSS (Spreading Method) when using SNAP(R), otherwise also FSK and OOK is possible Mesh (SNAP(R)) Mesh networking Topology Manufactured in conformance with RoHS 2. APPLICATIONS FOR THE MODULE * * * * Automatic Meter Reading Inventory management, Factory- and home automation Wireless Sensor Networks, e.g. Lighting Control Monitoring (environmental, patient or fitness) 3. DESCRIPTION FOR THE MODULE The PAN2580 module is a short range, low power, 868MHZ or 915MHz ISM band transceiver which includes a complete 802.15.4 physical layer (PHY). It is designed for the IEEE 802.15.4 wireless standard. Using an appropriate microcontroller (MCU) with reference oscillator provides a cost effective solution for short range data links and networks. The PAN2580 use the MCU with integrated Transceiver Si100x from Silicon Labs It comes pre-loaded with the Synapse SNAP(R) mesh network operating system. Please contact your local sales office for further details on additional options and services, by visiting www.panasonic.com/rfmodules or write an e-mail to wireless@eu.panasonic.com. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 5 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 4. SCOPE OF THIS DOCUMENT This product specification applies to Panasonic's 802.15.4 Modem PAN2580 // ENW59625xxxF. Different versions of the PAN2580 are available (refer to chapter 23). 5. HISTORY FOR THIS DOCUMENT Revision Date Modification / Remarks 1.0 1.1 07.09.2011 15.11.2012 Initial draft version Add Pin-Header Module PAN4580ETU PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 6 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 6. TERMINAL LAYOUT PAN2580 (SMD Module) Top view Pin No. PAN2580 A1, A8, B8, C8, D8, F8, G8, H1, H8 A2, A3 1 PAN2580ETU (Pin-header Module) Top view UFL Conector (option) Pin No. PAN4580ETU Pin Name 1, 24 GND DC Power supply, 0V 21 VCC DC Power supply, typical 3V (2.7 ~ 3.6V) A4 3 P2.2 11 GPIO_1, ADC18, I2C SCL A5 4 P2.3 12 A6 16 P1.6 (7) A7 14 P1.7 (8) B4 2 P2.1 10 GPIO_2, ADC19 Not Available, Do Not Connect (used for access to the onboard external memory) Not Available, Do Not Connect (used for access to the onboard external memory) GPIO_0, ADC17, I2C SDA B5 5 P2.4 13 B6 15 P1.5 (6) B7 13 P2.0 (9) C4 20 ANT_A 18 GPIO_3, ADC20 Not Available, Do Not Connect (used for access to the onboard external memory) Not Available, Do Not Connect (used for access to the onboard external memory) GPIO_18 (Output Only) C5 12 P0.2_XTAL1 1 GPIO_10, ADC2, UART0 RTS Input SNAPpy Description IO 1 When using SNAP(R) Software by Synapse Wireless, Inc. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 7 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 Pin No. PAN2580 Pin No. PAN4580ETU Pin Name SNAPpy Description IO 1 E3 19 GPIO_0 17 E8 RF IN/OUT GPIO_0 (General Purpose I/O) EZRadioPRO peripheral transmit RF output / input pin (only ENW59625CxxF, other modules NC) GPIO_6, ADC0, Interrupt, External Voltage Reference, SPI MISO GPIO_4, ADC21, SPI MOSI F4 8 P0.0_VREF 0 G2 6 P2.5 14 G3 11 P0.3_XTAL1 2 G4 9 P0.5_RX 4 G5 17 P=0.6_CNVSTR 5 H2 18 P2.7_C2D 16 H3 7 P2.6 15 H4 10 P0.4_TX 3 H5 23 RESET#_C2D GPIO_9, ADC3, UART0 CTS Output GPIO_7, ADC5, Interrupt, UART0 Rx Data Input GPIO_15, ADC6, External "Start Conversion" for ADC0 GPIO_16 (limited drive strength as it is routed through a 1Kohm resistor. The signal driven from (or to) GPIO16 can also be read, or driven, on pin H6, the debug pin. GPIO_5, ADC22, SPI SCLK GPIO_8, ADC4, Interrupt, UART0 Tx Data Output Module Reset, Active Low P2.7_C2D Background Debug Communications NC - H6 22 B1, B2, B3, C1, C2, C3, C6, C7, D1, D2, D3, D4, D5, D6, D7, E1, E2, E4, E5, E6, E7, F1, F2, F3, F5, F6, F7, G1, G6, G7, H7 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 8 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 7. BLOCK DIAGRAM 7.1. PAN2580-868MHZ (ENW59625xxCF, ENW59635xxCF) 7.2. PAN2580-915MHZ (ENW59625xxDF, ENW59635xxDF) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 9 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 8. KEY PARTS LIST Part Name P.W.Board Casing IC part name Material Glass cloth epoxide resin with gold plating Material: C7521, thickness 0.15mm SI1000 (ENW596x5xxDF) or SI1002 (ENW596x5xxCF) SiLabs, www.silabs.com 9. TEST CONDITIONS Measurements are made under room temperature and humidity unless otherwise specified. Temperature 25 10C Humidity 40 to 85%RH Supply voltage 3.0V 10. ABSOLUTE MAXIMUM RATINGS The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. No. Item Symbol 1 2 3 Ambient Temperature under Bias Storage Temperature Supply voltage (1) Voltage on any Px.x I/O Pin or RST with Respect to GND Maximum Total Current through all Px.x Pins ESD on any pin except for optional pins E8 (RF in/out) and UFL connector. Human Body Model (HBM) ESD on optional pins E8 (RF in/out) and UFL connector. Human Body Model (HBM) Surface Mount Solder Reflow Temperature Top Tstg VCC 4 5 6 7 8 Vin Absolute Maximum Ratings -40 to +85 -40 to +85 -0.3 to +3.6 -0.3 to VCC+0.5 Unit C C Vdc Vdc Iin 200 mA VTHHBM1 2 kV VTHHBM2 1 kV TDeath Please refer to chapter 15.2. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 10 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 No. Item Symbol 9 Moisture Sensitivity Level MSL Absolute Maximum Ratings 4 (72 hours) Unit Notes: (1) The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, please provide a decoupling circuit (for example a ferrite in series connection and a blocking capacitor to ground). 11. OPERATING CONDITIONS No. Item 1 Supply voltage 2.1 2.2 RF Frequency 915MHz RF Frequency 868MHz (3) Logic Low Level Input Voltage Logic High Level Input Voltage Operating temperature range 3 4 5 Min Value Typ Max Unit VCC 2.7 3.0 3.6 Vdc fRF fRF 902.0 868.1 927.6 868.5 MHz MHz VIL 0 0.6 V VIH VCC- 0.6 - V Top -40 +85 C Condition / Remark Symbol The typical value is recommended Input / Output Input / Output 12. DC ELECTRICAL CHARACERISTICS Assume VCC = 3.0V, Tamb = 25C if nothing else stated No. Item 1 2 3 Current consumption in transmit mode Current consumption in receive mode Current consumption in sleep mode(2). Condition / Remark ENW596x5xxCF (868MHz) ENW596x5xxDF (915MHz) ENW596x5xxCF (868MHz) ENW596x5xxDF (915MHz) ENW596x5xxCF (868MHz) ENW596x5xxDF (915MHz) Symbol Min ICCT - ICCR - ICCSM - Value Typ 48 80 25 25 Max 65 100 33 33 1.5 - Unit mA mA A Notes: (2) For sleep-mode settings refer to the SNAP Reference Manual [3] (3) In case, when SNAP Software from Synapse is used. Please ask the relevant Product Manager in your region, in case you want to address a different band. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 11 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 13. A/D CONVERTER CHARACTERISTICS No. Item Condition / Remark Min Value Typ Max Unit DC Accuracy 1 Resolution 10 bits 2 Integral Nonlinearity 0.5 1 LSB 3 Differential Nonlinearity Guaranteed Monotonic 0.5 1 LSB 4 Offset Error <1 2 LSB 5 Full Scale Error 1 2.5 LSB Dynamic performance (10 kHz sine-wave single-ended input, 1 dB below Full Scale, 300 ksps) Signal-to-Noise Plus 6 54 58 dB Distortion 7 Signal-to-Distortion 73 dB Spurious-Free Dynamic 8 75 dB Range Conversion Rate 9 SAR Conversion Clock 7.33 MHz 13 Conversion Time in SAR 10-bit Mode clock 10 Clocks s 8-bit Mode 11 Track/Hold Acquisition 11 1.5 s Time 12 Throughput Rate 300 ksps Analog Inputs ADC Input Voltage 13 Single Ended (AIN+ - GND) 0 VREF V Range Absolute Pin Voltage with respect 14 Single Ended 0 VCC V to GND 1x Gain 30 15 Sampling Capacitance pF 0.5x Gain 28 Input Multiplexer 16 5 k Impedance Power Specifications Power Supply Current Conversion Mode (300 ksps) 800 17 A (VDD supplied to Tracking Mode (0 ksps) 680 ADC0) Internal High Speed VREF 67 18 Power Supply Rejection dB External VREF 74 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 12 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 14. AC ELECTRICAL CHARACTERISTICS No. Receiver 1.1 1.2 1.4 2 RX Sensitivity 4 Saturation Frequency Error Tolerance Spurious Emissions 5 Image Rejection 6 RSSI Resolution 1-Ch Offset Selectivity 2-Ch Offset Selectivity 3-Ch Offset Selectivity Blocking at 1 MHz Offset Blocking at 4 MHz Offset Blocking at 8 MHz Offset 3 7 8 9 10 11 12 Min Limit Typ Max -92 -95 - -101 -104 5 - - - 70 kHz - - -54 dBm - -30 - dB - 0.5 - dB Desired Ref Signal 3 dB above sensitivity, BER < 0.1%. Interferer and desired modulated with 40 kbps F = 20 kHz GFSK with BT = 0.5, channel spacing = 150 kHz - -31 - dB -35 - dB -40 - dB - -52 - dB - -56 - dB - -63 - dB Min 15 9 - Limit Typ 18 13 19 250 -50 -44 - Max 22 16 -35 -35 -54 -54 Conditions 1% Packet Error Rate (PER), -85dBm required by [1] Wireless M-Bus Mode T1, T2(4) Wireless M-Bus Mode S1, S2(4) maximum input level AFC on, 1% PER Rejection at the image frequency. IF=937 kHz Desired Ref Signal 3 dB above sensitivity. Interferer and desired modulated with 40 kbps F = 20 kHz GFSK with BT = 0.5 No. Transmitter Conditions 1 Output Power (max) ENW596x5xxCF (868MHz) ENW596x5xxDF (915MHz) 2 3 4 5 6 7 Power Control Range Over the Air Data Rate 2nd harmonic 3rd harmonic Spurious Emissions <1GHz Spurious Emissions >1GHz (4) Fixed by Synapse Software maximum output power maximum output power POUT = 11 dBm excluding harmonics Unit dBm dBm Unit dBm dBm dB kbps dBm dBm dBm dBm When using Wireless M-Bus software, only for ENW596x5xxCF (868MHz) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 13 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 15. SOLDERING TEMPERATURE - TIME PROFILE FOR REFLOW SOLDERING (only SMD ModulePAN2580 / ENW59625xxxF) 15.1. FOR LEAD SOLDER 10 1s Recommended temp. profile for reflow soldering 30 +20/-10s 235C max. Temp.[C] 220 5C 200C 150 10C 90 30s Time [s] 15.2. FOR LEAD FREE SOLDER Our used temp. profile for reflow soldering Temp.[C] 30 +20/-10s 230C -250C max. 220C 150C - 190C 90 30s Time [s] Reflow permissible cycles: 2 Opposite side reflow is prohibited due to the module weight. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 14 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 16. MODULE DIMENSIONS 16.1. SMD MODULE PAN2580 / ENW59625XXXF Item Dimension Tolerance Remark Width Lenght Height 19.00 29.80 2.55 0.25 0.25 0.25 With case 16.2. PIN HEADER MODULE PAN2580ETU / ENW59635XXXF Item Dimension Tolerance Remark Width Lenght Height 33.86 33.86 7.31 0.25 0.25 0.25 With pin-header PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 15 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 17. FOOTPRINT OF THE MODULE 17.1. SMD MODULE PAN2580 / ENW59625XXXF All dimensions are in millimeters. The outer dimensions have a tolerance of 0.25mm. Mechanical Requirements Item Solderability Limit Condition More than 75% of the soldering area Reflow soldering with recommendable shall be coated by solder temperature profile PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 16 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 17.2. PIN HEADER MODULE PAN2580ETU / ENW59635XXXF All dimensions are in millimeters. The outer dimensions have a tolerance of 0.25mm. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 17 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 18. RECOMMENDED LAND PATTERN 19.00 min. 8mm 1.10 14,00 2.40 18.1. SMD MODULE PAN2580 / ENW59625XXXF Dimensions in millimeters. The land pattern dimensions above are meant to serve only as a guid. This information is provided without any legal liability. For the footprint it is recommended to use the same pad-size like the module footprint. Please refer to chapter 17. Foot Print of the Module. Also for the solder paste screen we recommend to use the same pad-size like for the module. Solder paste screen cutouts (with slightly different dimensions) might be optimum depending on your soldering process. For example, the chosen solder paste screen thickness might have an effect. The solder screen thickness depends on your production standard. We recommend 100m to 120m. When using the antenna pad version, place the antenna on the edge of your carrier board (if allowable). If you have any questions on these points, please contact your local Panasonic representative. Before releasing the layout, we recommend to sent the schematic and layout for final check to wireless@eu.panasonic.com. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 18 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 1.20 2.00 25.00 8.86 1.80 18.2. PIN HEADER MODULE PAN2580ETU / ENW59635XXXF Dimensions in millimeters. The land pattern dimensions above are meant to serve only as a guid. This information is provided without any legal liability. When using a module with an embedded antenna, for optimum RF performance, place the antenna on the edge of your application PCB If you have any questions on these points, please contact your local Panasonic representative. Schematics and layouts may be sent to wireless@eu.panasonic.com for final review. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 19 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 19. LASER MARKING SMD Module PAN2580 / ENW59625xxxF Pin header Module PAN2580ETU / ENW59635xxxF The 2D-Barcode contains the following information separated by a semicolon: Value Date-code MAC-adress 59625xxx yyzz Description Date code in the format Year - Calender Week - Day of Week - Line Lot [YYWWDLL] Last 8 digits of the MAC-adress Ordering number [8 signs; without the first 3 digits (ENW) and the last digit (F), please refer also to chapter 23] The identifier for the hardware release [2 signs, here yy] and the software release [2 signs, here zz] The point on the marking (below left) is the identifier for pin 1 of the module. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 20 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 20. RELIABILITY TESTS The measurement should be done after being exposed to room temperature and humidity for 1 hour. No. Item Limit 1 Heat-shock-restance test Electrical parameter should be in specification 2 Humidity load life test the same as above 3 Vibration test the same as above 4 ESD test the same as above 5 MSL test the same as above Condition Temperature:125C to -50C Voltage: off Period: 500cycles Temp. Cycle: -50C and +125C each 7min. Temprerature: +85C Humidity: 85% Period: 500hrs Voltage: on Vibration Ampl.: 1.5mm Vibr. Freq.: 10~55~10Hz (total 1min.) Directions: X; Y; Z each 1hrs Regarding JEDEC JESD-22a114D each contact with 100pF, 1.5kOhm min. 1kV (Human Body Model HBM) Pre conditioning: Temperature: +85V Humidity: 85C Period: 96hrs Soldering condition: Peak: 260C for ~10s, 2 times 21. CAUTIONS Failure to do so may result in degrading of the product's functions and damage to the product. 21.1. DESIGN NOTES (1) (2) (3) (4) (5) (6) Please follow the conditions written in this specification, especially the control signals of this module. The supply voltage has to be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a blocking capacitor to ground of at least 47uF directly at the module). This product should not be mechanically stressed when installed. Heat is the major cause of shortening the life of these products. Please keep this product away from heat. Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum tolerance. The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. Please keep this product away from other high frequency circuits. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 21 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 21.2. INSTALLATION NOTES (1) (2) (3) (4) (5) (6) (7) (8) (9) Reflow soldering is possible twice based on the conditions in chapter 15. Please set up the temperature at the soldering portion of this product according to this reflow profile. Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. This product should not be mechanically stressed or vibrated when reflowed. If you want to repair your board by hand soldering, please keep the conditions of this chapter. Please do not wash this product. Please refer to the recommended pattern when designing a board. Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. 21.3. USAGE CONDITIONS NOTES (1) (2) (3) (4) (5) (6) (7) Please take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. Please do not use dropped products. Please do not touch, damage or place dirt on the pins. Please follow the recommended condition ratings about the power supply applied to this product. Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. 21.4. STORAGE NOTES (1) (2) (3) (4) (5) (6) The module may not be stressed mechanically during storage. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX Storage in direct sunlight Storage in an environment where the temperature may be outside the range of 5C to 35C range, or where the humidity may be outside the 45 to 85% range. Storage of the products for more than one year after the date of delivery at your PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 22 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 company if the avoidance all the above conditions (1) to (3) have been met. Storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. (8) Please keep this product away from water, poisonous gas and corrosive gas. (9) This product should not be stressed or shocked when transported. (10) Please follow the specification when stacking packed crates (max. 10). (7) 21.5. SAFETY CAUTIONS These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications, without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 21.6. OTHER CAUTIONS (1) This specification sheet is copyrighted. Please do not disclose it to a third party. (2) Please do not use the products for other purposes than those listed. (3) Be sure to provide an appropriate fail-safe function on your product to prevent an additional damage that may be caused by the abnormal function or the failure of the product. (4) This product has not been manufactured with any ozone chemical controlled under the Montreal Protocol. (5) These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. (6) In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. (7) In direct sunlight, outdoors, or in a dusty environment (8) In an environment where condensation occurs. (9) In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX) (10) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. (11) When you have any question or uncertainty, both of you and Panasonic sincerely cope with it. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-PAN2580-102 PRODUCT SPECIFICATION REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 23 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 22. PACKAGING OF SMD MODULE PAN2580 ENW59625XXXF 22.1. TAPE DIMENSION Y T 0.35 0.05 Do O 1.55 0.05 P2 2.00 0.15 (I) E1 1.75 0.10 Po 4.00 0.10 (II) D1 O 2.00 min. F (III) So Bo Typ. R K1 0.30 Y R 0.75 A 0.20 0.05 Ko W P1 Ao SECTIONY-Y SCALE 1.45 : 1 DETAIL A SCALE 6 : 1 Ao Bo Ko K1 F P1 So W 19.40 30.20 3.80 2.95 20.20 28.00 40.40 44.00 +/- 0.10 +/- 0.10 +/- 0.20 +/- 0.10 +/- 0.15 +/- 0.10 +/- 0.10 +/- 0.30 Measured from centreline of sprocket hole (I) (II) (III) Forming format : Flatbed - 8 Estimated max. length : 50 (IV) meter/22B6 reel to centreline of pocket. Cumulative tolerance of 10 sprocket holes is 0.20 . Measured from centreline of sprocket hole to centreline of pocket. Other material available. ALL DIMENSIONS IN MILLIMETRES UNLESS OTHERWISE STATED. 22.2. PACKING IN TAPE trailer (empty) 1 x circumference /hub (min 160mm) component packed area standard 500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules. Empty spaces in component packed area shall be less than two per reel and those spaces shall not be consecutive. Top cover tape shall not be found on reel holes and shall not stick out from reel. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 24 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 22.3. COMPONENT DIRECTION Please refer also to chapter 18. Labeling Drawing 22.4. REEL DIMENSION PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 25 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 22.5. LABEL FOR PACKAGE The label below shows only an example. (3P):PAN2580 Customer Code ENW59625xxxF 500 (1T): (1P) (2P) (3P) (9D) (Q) (HW/SW) [[G]] Lotcode [YYWWDLL] YY year above 08 WW normal calendar week above 01 D day above 5 (Friday) L line identifier, if more as one actual 1 L lot identifier per day e.g. 1, 2, 3 Customer Order Code, if any, otherwise put company name on it. Panasonic Part Number, please refer to chapter 23 Ordering Information Module type Datecode as [2xYear, 2xMonth, 2xDay] Quantity [XXXX], variable Hardware /Software Release identifier Identifier that the product is RoHS conform, please refer to chapter 24. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 26 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 22.6. TOTAL PACKING HANDLING 22.7. COVER TAPE REEL STRENGTH Force direction = 10deg Speed = 300mm/min. Cover tape reel strength =0.098~0.68N (10~70g) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 27 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 23. ORDERING INFORMATION No. Ordering part number Module-Type Connection- Frequency Output Type Power 1 ENW59625A1CF PAN2580M-868A SMD 868MHz 13dBm 2 ENW59625A5CF PAN2580M-868A SMD 868MHz 13dBm 3 ENW59625B1CF PAN2580M-868B SMD 868MHz 13dBm 4 ENW59625B5CF PAN2580M-868B SMD 868MHz 13dBm 5 ENW59625C1CF PAN2580M-868C SMD 868MHz 13dBm 6 ENW59625C5CF PAN2580M-868C SMD 868MHz 13dBm 7 ENW59625A1DF PAN2580H-915A SMD 915MHz 18dBm 8 ENW59625A5DF PAN2580H-915A SMD 915MHz 18dBm 9 ENW59625B1DF PAN2580H-915B SMD 915MHz 18dBm 10 ENW59625B5DF PAN2580H-915B SMD 915MHz 18dBm 11 ENW59625C1DF PAN2580H-915C SMD 915MHz 18dBm 12 ENW59625C5DF PAN2580H-915C SMD 915MHz 18dBm 13 ENW59635A1CF PAN2580ETU8MA Pin-Header 868MHz 13dBm 14 ENW59635A5CF PAN2580ETU8MA Pin-Header 868MHz 13dBm 15 ENW59635B1CF PAN2580ETU8MB Pin-Header 868MHz 13dBm 16 ENW59635B5CF PAN2580ETU8MB Pin-Header 868MHz 13dBm 17 ENW59635A1DF PAN2580ETU9HA Pin-Header 915MHz 18dBm 18 ENW59635A5DF PAN2580ETU9HA Pin-Header 915MHz 18dBm 19 ENW59635B1DF PAN2580ETU9HB Pin-Header 915MHz 18dBm 20 ENW59635B5DF PAN2580ETU9HB Pin-Header 915MHz 18dBm RF-output Software Ceramic Antenna Ceramic Antenna UFLConnector UFLConnector OutputPin OutputPin Ceramic Antenna Ceramic Antenna UFLConnector UFLConnector OutputPin OutputPin Ceramic Antenna Ceramic Antenna UFLConnector UFLConnector Ceramic Antenna Ceramic Antenna UFLConnector UFLConnector no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) no (5) SNAP (6) (5) Without software. 64kbyte (SI100x) + 128kbyte (EEprom) of free In-System Flash Memory (6) Synapse SNAP software included, please refer also to [3]. 192kbyte Flash Memory, with 64kbyte used by SNAP core, 64kbyte free for uploadable SNAPpy scripts and 64k reserved. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 28 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 24. ROHS DECLARATION Declaration of environmental compatibility for supplied products: Hereby we declare to our best present knowledge based on declaration of our suppliers that this product does not contain the following substances which are banned by Directive 2002/95/EC (RoHS) or contains a maximum concentration of 0.1% by weight in homogeneous materials for * * * * * Lead and lead compounds Mercury and mercury compounds Chromium (VI) PBB (polybrominated biphenyl) category PBDE (polybrominated biphenyl ether) category And a maximum concentration of 0.01% by weight in homogeneous materials for * Cadmium and cadmium compounds 25. DATA SHEET STATUS This data sheet contains data from the PRELIMINARY specification. Supplementary data will be published at a later date. Panasonic Electronic Devices Europe GmbH reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Please consult the most recently issued data sheet before initiating or completing a design. If there is an update, please download under: PAN2580 Latest Data Sheet! 26. REGULATORY INFORMATION 26.1. FCC NOTICE The device PAN2580, including the ceramic antenna (ENW59625AxDF) and also the SMD type (ENW59625CxDF), including with the antennas, which are listed in 26.5, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 26.2. CAUTION The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Electronic Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 29 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help 26.3. LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label (laser marking) on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V-2580. In any case end product must be labelled exterior with "Contains FCC ID: T7V-2580" 26.4. ANTENNA WARNING The related part number for this device is ENW59625BxDF (PAN2580 with U.FL connector) and ENW59625CxDF (PAN2580 with SMD pad). For details, please see the chapter 23. Ordering Information. This device is tested with a standard SMA connector and with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with nonapproved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for this device with the antenna listed in item 1 are the same (FCC ID: T7V-2580). 26.5. APPROVED ANTENNA LIST Note: We are able to qualify your antenna and will add to this list as that process is completed. Item Part Number Manufacturer 1 0915AT43A0026 Johanson 2 TB2-900D-MMCX Frequency Band Type Average Gain ceramic chip 902 - 928 MHz -4dBi antenna external 890 - 960 MHz +2dBi dedicated PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 30 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 26.6. RF EXPOSURE PAN2580 To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that the approved antenna in the previous table must be installed. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of PAN2580 with mounted ceramic antenna (FCC ID: T7V-2580) is below the FCC radio frequency exposure limits. Nevertheless, the PAN2580 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. 27. INDUSTRY CANADA CERTIFICATION PAN2580 is licensed to meet the regulatory requirements of Industry Canada (IC), license: IC: 216Q-2580 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in Table 26.5 above. Antennas not included in this list are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 28. EUROPEAN R&TTE DECLARATION OF CONFORMITY Hereby, Panasonic Electronic Devices Europe GmbH, declares that the module PAN2580 and their versions is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. As a result of the conformity assessment procedure described in Annex III of the Directive 1999/5/EC, the end-customer equipment should be labelled as follows: PAN2580 and their versions in the specified reference design can be used in the following countries: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, The Netherlands, the United Kingdom, Switzerland, and Norway. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 31 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 29. RELATED DOCUMENTS For an update, please search in the suitable homepage. [1] IEEE Standard 802.15.4 -2003 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LRWPANs) [2] Technical Datasheet Si1000/1/2/3/4/5 Rev. 1.0 9/10 You can download the latest datasheet from the SiLabs homepage here. [3] Manual to the Evaluation Kit from Synapse, which fits to module hardware from Panasonic [Downloads: SNAP(R) Reference Manual Updated 10/2/2008; SNAP Hardware Technical Manual Updated 10/2/2008] Each new release from Synapse, will be posted here. Be sure to be registered free under http://forums.synapse-wireless.com. 30. GENERAL INFORMATION (c) Panasonic Electronic Devices Europe GmbH 2012. All rights reserved. This product description does not claim to be complete and free of mistakes. Please contact the related product manager with any errata inquries. If we deliver samples to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet completed. Engineering Samples may be partially or fully functional, and there may be differences published in the Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic Electronic Devices Europe GmbH disclaims any liability or product warranty for Engineering Samples. In particular, Panasonic Electronic Devices Europe GmbH disclaims liability for damages caused by * the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in an other product to be sold by Customer, * deviation or lapse in function of Engineering Sample, * improper use of Engineering Samples. Panasonic Electronic Devices Europe GmbH disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION No. DS-PAN2580-102 REV. 1.1 SUBJECT 802.15.4-MODEM PAGE 32 of 32 CUSTOMER'S CODE PAN2580 / PAN2580ETU PANASONIC'S CODE ENW59625xxxF / ENW59635xxxF DATE 15.11.2012 31. LIFE SUPPORT POLICY This Panasonic Electronic Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Electronic Devices Europe GmbH for any damages resulting. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de