Du line Output Module Type G 3430 4445 (R) Fieldbus Installationbus * 4-channel receiver * Relay load: 16 A * Module load: 64 A (16 A per relay) * Galvanically separated SPST relay outputs * H4-housing * For mounting on DIN-rail (EN 50022) * LED-indications for supply, Dupline(R) carrier and outputs * AC power supply * Address coding by GAP 1605 Ordering Key Product Description (R) Dupline receiver designed to be a part of the Dupline(R) concept for Building Auto- mation. SPST relay outputs for control of 4 loads of up to 250 VAC/16 A. Type Selection Ordering no. 24 VAC 115 VAC 230 VAC G3430 4445 024 G3430 4445 115 G3430 4445 230 Output Specifications 4 SPST relays (micro gap) 16 A 5x106 operations 1x105 operations/250 V, 12 A 100 mA/12 V 60 operations/min. 4 kVAC (rms) 1 pulse train Supply Specifications Power Supply Rated operational voltage Through term. 21 & 22 Frequency Rated operational power Max. power dissipation Type: Dupline H4-housing Receiver Number of channels Output type Power supply Supply Specifications (cont.) Supply Outputs Contact ratings (AgSn02) Resistive loads AC1 Mechanical lifetime Electrical lifetime Minimum load Operating frequency Dielectric voltage Outputs - Dupline(R) Response time G 3430 4445 024 (R) Overvoltage cat. III (IEC 60664) 230 VAC, +/- 10% (IEC 60038) 115 VAC, +/- 10% (IEC 60038) 24 VAC, +/- 10% 45 to 65 Hz Typ. 2,5 VA 7W Power supply (cont.) Rated impulse withstand volt. 230 115 024 Dielectric voltage Supply - Dupline(R) Supply - Outputs 4 kV 2,5 kV 800 V 4 kVAC (rms) 2 kVAC (rms) General Specifications Fail polarity state delay Upon loss of Dupline(R) carrier Power ON delay Indication for: Supply ON Dupline(R) carrier Output ON Environment Degree of protection Pollution degree Operating temperature Storage temperature Humidity (non-condensing) Mechanical resistance Shock Vibration Housing Weight Specifications are subject to change without notice (28.09.2005) Dupline(R) is a registered trademark. A product of the CARLO GAVAZZI Group 20 ms typ. 2s LED, Green LED, Yellow LED, red (one per output) IP 20 3 (IEC 60664) -5 to +50C (+23 to +122F) -50 to +85C (-58 to +185F) 20 to 80% 5 G (11ms) 2 G (6 to 55Hz) H4-housing 400 g 1 Du line G 3430 4445 ... (R) Fieldbus Installationbus Operation Diagram Power supply Dupline(R) carrier Transmission on channel for output 1 Output 1 (term. 24 & 25) Transmission on channel for output 2 Output 2 (term. 27 & 28) Dimensions (mm) Mode of Operation 4-channel receiver with 4 normally open contact outputs. Each output is individually coded by means of the code programmer GAP 1605. For changing the default setting, please refer to the datasheet on GAP 1605. The outputs are normally OFF. When a transmitter coded to the selected channel is activated, the output turns ON and remains ON until the respective channel becomes deactivated. The default set- ting is such that upon loss of Dupline(R) carrier all the outputs go OFF. H4-housing Note: At delivery some of the relays might be ON due to transportation bumps. To be sure that the relays are OFF, connect the module to power and Dupline and transmit on channels A1-4 once. Note: Due to the construction with bistable relays, the module is intended for heating and light control only. Wiring Diagram Output Specifications, Relay Data 4 channels G 3430 4445 ... SPST relay output Load Test conditions Typical number of operations 250 V, 12 A, cos =1 1800/h, 50% DC, +70C 1.0 x 105 250 V, 8 A, cos =1 1800/h, 50% DC, +70C 3.5 x 105 250 V, 4 A, cos =1 1800/h, 50% DC, +70C 5.0 x 105 250 V, 3 A, cos =1 1800/h, 50% DC, +70C 7.5 x 105 230 V, 550 W filament lamps Iin 40 Apeak Ioff = 2.5 A 60/h, 8% DC, +22C 2.0 x 105 230 V, 1000 W filament lamps Iin 71.5 Apeak Ioff = 4.5 A 60/h, 8% DC, +25C 7.0 x 104 230 V, 900 W fluorescent tubes (25 x 36 W) parallel compensated, 30 F 360/h, 50% DC, +25C 1.0 x 104 230 V, compressor Iin 21 Apeak Ioff =3.5 A cos = 0.5 500/h, 20% DC, +25C 1.7 x 105 250 V, 8 A, cos = 0.3 360/h, 50% DC, +25C 1.0 x 105 L1/L2/L3 N L1/L2/L3 D+ D1 2 3 4 5 6 7 8 3 4 1 2 Supply 21 22 23 24 25 26 27 28 L1/L2/L3 L N N L1/L2/L3 Default setting (fail polarity): OFF Accessories DIN-rail FMD 411 For further information, see "Accessories". 2 Specifications are subject to change without notice (28.09.2005) Dupline(R) is a registered trademark. A product of the CARLO GAVAZZI Group