G34304445115 - Carlo Gavazzi Group

Du line

Fieldbus Installationbus

Specifications are subject to change without notice (28.09.2005) 1

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Product Description Ordering Key

Type: Dupline®

H4-housing

Receiver

Number of channels

Output type

Power supply

Output Module

Type G 3430 4445

• 4-channel receiver

• Relay load: 16 A

• Module load: 64 A (16 A per relay)

• Galvanically separated SPST relay outputs

• H4-housing

• For mounting on DIN-rail (EN 50022)

• LED-indications for supply, Dupline®carrier and outputs

• AC power supply

• Address coding by GAP 1605

Dupline receiver®designed to

be a part of the Dupline®

concept for Building Auto-

Type Selection

Supply Ordering no.

24 VAC G3430 4445 024

115 VAC G3430 4445 115

230 VAC G3430 4445 230

mation. SPST relay outputs

for control of 4 loads of up to

250 VAC/16 A.

Output Specifications

Outputs 4 SPST relays

Contact ratings (AgSn02) µ (micro gap)

Resistive loads AC1 16 A

Mechanical lifetime 5x106operations

Electrical lifetime

1x105operations/250 V, 12 A

Minimum load 100 mA/12 V

Operating frequency 60 operations/min.

Dielectric voltage

Outputs – Dupline®≥4 kVAC (rms)

Response time ≤1 pulse train

G 3430 4445 024

Supply Specifications

Power Supply

Overvoltage cat. III (IEC 60664)

Rated operational voltage

Through term. 21 & 22

230 VAC, +/- 10% (IEC 60038)

115 VAC, +/- 10% (IEC 60038)

24 VAC, +/- 10%

Frequency 45 to 65 Hz

Rated operational power Typ. 2,5 VA

Max. power dissipation 7 W

General Specifications

Fail polarity state delay

Upon loss of Dupline®carrier ≤20 ms

Power ON delay typ. 2s

Indication for:

Supply ON LED, Green

Dupline®carrier LED, Yellow

Output ON

LED, red (one per output)

Environment

Degree of protection IP 20

Pollution degree 3 (IEC 60664)

Operating temperature

-5 to +50°C (+23° to +122°F)

Storage temperature

-50 to +85°C (-58° to +185°F)

Humidity (non-condensing) 20 to 80%

Mechanical resistance

Shock 5 G (11ms)

Vibration 2 G (6 to 55Hz)

Housing H4-housing

Weight 400 g

Supply Specifications (cont.)

Power supply (cont.)

Rated impulse withstand volt.

230 4 kV

115 2,5 kV

024 800 V

Dielectric voltage

Supply – Dupline®≥4 kVAC (rms)

Supply – Outputs ≥2 kVAC (rms)

21 22 23 24 25 26 27 28

1 2 3 4 5 6 7 8

Supply

D+

L1/L2/L3

D-

L1/L2/L3

Du line

Fieldbus Installationbus

2Specifications are subject to change without notice (28.09.2005)

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Wiring Diagram

Accessories

DIN-rail FMD 411

For further information, see "Accessories".

4 channels G 3430 4445 ...

SPST relay output

G 3430 4445 ...

Operation Diagram

Dupline®carrier

Transmission on channel for output 1

Output 1 (term. 24 & 25)

Transmission on channel for output 2

Power supply

Output 2 (term. 27 & 28)

Default setting (fail polarity): OFF

Mode of Operation

4-channel receiver with 4

normally open contact out-

puts. Each output is individu-

ally coded by means of the

code programmer GAP 1605.

For changing the default set-

ting, please refer to the

datasheet on GAP 1605.

The outputs are normally OFF.

When a transmitter coded

the selected channel is acti-

vated, the output turns ON

and remains ON until the

respective channel becomes

deactivated. The default set-

ting is such that upon loss of

Dupline®carrier all the out-

puts go OFF.

Note: At delivery some of the

relays might be ON due to

transportation bumps. To be

sure that the relays are OFF,

connect the module to power

and Dupline and transmit on

channels A1-4 once.

Note: Due to the construc-

tion with bistable relays, the

module is intended for heat-

ing and light control only.

Dimensions (mm)

H4-housing

Output Specifications, Relay Data

Load Test conditions Typical number

of operations

250 V, 12 A, cos ϕ =1 1800/h, 50% DC, +70°C 1.0 x 105

250 V, 8 A, cos ϕ =1 1800/h, 50% DC, +70°C 3.5 x 105

250 V, 4 A, cos ϕ =1 1800/h, 50% DC, +70°C 5.0 x 105

250 V, 3 A, cos ϕ =1 1800/h, 50% DC, +70°C 7.5 x 105

230 V, 550 W

filament lamps

Iin ≤40 Apeak

Ioff = 2.5 A 60/h, 8% DC, +22°C 2.0 x 105

230 V, 1000 W

filament lamps

Iin ≤71.5 Apeak

Ioff = 4.5 A 60/h, 8% DC, +25°C 7.0 x 104

230 V, 900 W

fluorescent tubes

(25 x 36 W)

parallel compensated,

30 µF 360/h, 50% DC, +25°C 1.0 x 104

230 V, compressor

Iin ≤21 Apeak

Ioff =3.5 A

cos ϕ = 0.5 500/h, 20% DC, +25°C 1.7 x 105

250 V, 8 A, cos ϕ = 0.3 360/h, 50% DC, +25°C 1.0 x 105