Typical Application Circuit and Functional Diagram appear
at end of data sheet.
Pin Configurations continued at end of data sheet.
Cell Phones
SAN/NAS
Servers
Notebooks
Satellite Radio
General Description
The MAX7327, a 2-wire serial-interfaced peripheral,
features 12 push-pull outputs and four configurable open-
drain I/O ports with selectable internal pullups and tran-
sition detection. Ports are overvoltage protected to +6V,
independent of supply voltage.
The four I/O ports configured as inputs are continuously
monitored for state changes (transition detection). State
changes are indicated by the open-drain, +6V-tolerant
INT output. The interrupt is latched, detecting transient
changes. When the MAX7327 is subsequently accessed
through the serial interface, any pending interrupt is
cleared. The 12 push-pull and the four open-drain outputs
are rated to sink 20mA, and are capable of driving LEDs.
The RST input clears the serial interface, terminating any
I2C communication to or from the MAX7327.
The MAX7327 uses two address inputs with four-level
logic to allow 16 I2C slave addresses. The slave address
also determines the power-up logic state for the I/O ports,
and enables or disables internal 40k pullups in groups
of two ports.
The MAX7327 is one device in a family of pin-compatible
port expanders with a choice of input ports, open-drain I/O
ports, and push-pull output ports (see Table 1).
The MAX7327 is available in the 24-pin QSOP and
TQFN packages, and is specified over the -40°C to
+125°C automotive temperature range.
Applications
Features
400kHz I2C Serial Interface
+1.71V to +5.5V Operating Voltage
12 Push-Pull Output Ports, Rated at 20mA Sink
Current
4 Open-Drain I/O Ports, Rated at 20mA Sink Current
I/O Ports are Overvoltage Protected to +6V
Selectable I/O Port Power-Up Default Logic States
Transient Changes are Latched, Allowing Detection
Between Read Operations
INT Output Alerts Changes on Inputs
AD0 and AD2 Inputs Select from 16 Slave Addresses
Low 0.6µA (typ) Standby Current
-40°C to +125°C Temperature Range
+Denotes a lead(Pb)-free/RoHS-compliant package.
**EP = Exposed pad.
PART INPUTS INTERRUPT
MASK
OPEN-
DRAIN
OUTPUTS
PUSH-PULL
OUTPUTS
MAX7324 8 Yes 8
MAX7325 Up to 8 Up to 8 8
MAX7326 4 Yes 12
MAX7327 Up to 4 Up to 4 12
PART TEMP RANGE PIN-PACKAGE
MAX7327AEG+ -40°C to +125°C 24 QSOP
MAX7327ATG+ -40°C to +125°C 24 TQFN-EP*
(4mm x 4mm)
MAX7327AATG+ -40°C to +125°C 24 TQFN-EP*
(3.5mm x 3.5mm)
TQFN (4mm x 4mm)
TOP VIEW
MAX7327
19
20
21
22
1 2 3 4 5 6
18 17 16 15 14 13
23
24
12
11
10
9
8
7
SCL
V+
SDA
INT
AD2
O0
+
O1
P2
P3
P4
P5
AD0
O15
O13
O12
O11
RST
O10
O8
O9
GND
O6
O7
O14
EXPOSED PADDLE
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
19-3805; Rev 1; 5/14
Selector Guide
Ordering Information
Pin Congurations
EVALUATION KIT AVAILABLE
(All voltages referenced to GND.)
Supply Voltage V+ ................................................... -0.3V to +6V
SCL, SDA, AD0, AD2, RST, INT, P2–P5 ...............-0.3V to +6V
O0, O1, O6–O15 ........................................... -0.3V to V+ + 0.3V
O0, O1, O6–O15 Output Current ....................................±25mA
P2–P5 Sink Current ..........................................................25mA
SDA Sink Current ..............................................................10mA
INT Sink Current ................................................................10mA
Total V+ Current ................................................................50mA
Total GND Current ...........................................................100mA
Continuous Power Dissipation (TA = +70°C)
24-Pin QSOP (derate 9.5mW/°C over +70°C) .........761.9mW
24-Pin TQFN (derate 20.8mW/°C over +70°C) ......1666.7mW
Operating Temperature Range ......................... -40°C to +125°C
Junction Temperature ...................................................... +150°C
Storage Temperature Range ............................ -65°C to +150°C
Lead Temperature (soldering, 10s) ................................. +300°C
(V+ = +1.71V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at V+ = +3.3V, TA = +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Operating Supply Voltage V+ TA = -40°C to +125°C 1.71 5.50 V
Power-On Reset Voltage VPOR V+ falling 1.6 V
Standby Current
(Interface Idle) ISTB
SCL and SDA and other
digital inputs at V+
TA = -40°C to
+125°C 0.6 1.9 µA
Supply Current
(Interface Running) I+ fSCL = 400kHz; other
digital inputs at V+
TA = -40°C to
+125°C 23 55 µA
Input High-Voltage
SDA, SCL, AD0, AD2, RST, P2–P5 VIH
V+ < 1.8V 0.8 x V+ V
V+ ≥ 1.8 V 0.7 x V+
Input Low-Voltage
SDA, SCL, AD0, AD2, RST, P2–P5 VIL
V+ < 1.8V 0.2 x V+ V
V+ ≥ 1.8 V 0.3 x V+
Input Leakage Current
SDA, SCL, AD0, AD2, RST, P2–P5 IIH, IIL
SDA, SCL, AD0, AD2, RST, P0–P7 at
V+ or GND, internal pullup disabled -0.2 +0.2 µA
Input Capacitance
SDA, SCL, AD0, AD2, RST, P2–P5 10 pF
Output Low Voltage
O8–O15, P0, P7 VOL
V+ = 1.71V, ISINK = 5mA (QSOP) 90 180
mV
V+ = 1.71V, ISINK = 5mA (TQFN) 90 230
V+ = 2.5V, ISINK = 10mA (QSOP) 110 210
V+ = 2.5V, ISINK = 10mA (TQFN) 110 260
V+ = 3.3V, ISINK = 15mA (QSOP) 130 230
V+ = 3.3V, ISINK = 15mA (TQFN) 130 280
V+ = 5V, ISINK = 20mA (QSOP) 140 250
V+ = 5V, ISINK = 20mA (TQFN) 140 300
Output High Voltage
O0, O1, O6–O15, P2–P5 VOH
V+ = +1.71V, ISOURCE = 2mA V+ - 250 V+ - 30
mV
V+ = +2.5V, ISOURCE = 5mA V+ - 360 V+ - 70
V+ = +3.3V, ISOURCE = 5mA V+ - 260 V+ - 100
V+ = +5V, ISOURCE = 10mA V+ - 360 V+ - 120
Output Low-Voltage SDA VOLSDA ISINK = 6mA 250 mV
Output Low-Voltage INT VOLINT ISINK = 5mA 130 250 mV
Port Input Pullup Resistor RPU 25 40 55 k
www.maximintegrated.com Maxim Integrated
2
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
DC Electrical Characteristics
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Absolute Maximum Ratings
Note 1: All parameters tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Note 2: A master device must provide a hold time of at least 300ns for the SDA signal (referred to VIL of the SCL signal) in order to
bridge the undefined region of SCL’s falling edge.
Note 3: Guaranteed by design.
Note 4: Cb = total capacitance of one bus line in pF. tR and tF measured between 0.3 x V+ and 0.7 x V+ with ISINK6mA.
Note 5: Input filters on the SDA and SCL inputs suppress noise spikes less than 50ns.
(V+ = +1.71V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at V+ = +3.3V, TA = +25°C.) (Note 1)
(V+ = +1.71V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at V+ = +3.3V, TA = +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Serial-Clock Frequency fSCL 400 kHz
Bus Free Time Between a STOP
and a START Condition tBUF 1.3 µs
Hold Time (Repeated) START
Condition tHD, STA 0.6 µs
Repeated START Condition
Setup Time tSU, STA 0.6 µs
STOP Condition Setup Time tSU, STO 0.6 µs
Data Hold Time tHD, DAT (Note 2) 0.9 µs
Data Setup Time tSU, DAT 100 ns
SCL Clock Low Period tLOW 1.3 µs
SCL Clock High Period tHIGH 0.7 µs
Rise Time of Both SDA and SCL
Signals, Receiving tR(Notes 3, 4) 20 +
0.1Cb
300 ns
Fall Time of Both SDA and SCL
Signals, Receiving tF(Notes 3, 4) 20 +
0.1Cb
300 ns
Fall Time of SDA Transmitting tF,TX (Notes 3, 4) 20 +
0.1Cb
250 ns
Pulse Width of Spike Suppressed tSP (Note 5) 50 ns
Capacitive Load for Each Bus
Line Cb(Note 3) 400 pF
RST Pulse Width tW500 ns
RST Rising to START Condition
Setup Time tRST 1 µs
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Port Output Data Valid tPPV CL ≤ 100pF 4 µs
Port Input Setup Time tPSU CL ≤ 100pF 0 µs
Port Input Hold Time tPH CL ≤ 100pF 4 µs
INT Input Data Valid Time tIV CL ≤ 100pF 4 µs
INT Reset Delay Time from STOP tIP CL ≤ 100pF 4 µs
INT Reset Delay Time from
Acknowledge tIR CL ≤ 100pF 4 µs
www.maximintegrated.com Maxim Integrated
3
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Timing Characteristics
Port and Interrupt INT Timing Characteristics
(TA = +25°C, unless otherwise noted.)
PIN NAME FUNCTION
QSOP TQFN
1 22 INT Active-Low Interrupt Output. INT is an open-drain output.
2 23 RST Active-Low Reset Input. Drive RST low to clear the 2-wire interface.
3, 21 24, 18 AD2, AD0 Address Inputs. Select device slave address with AD0 and AD2. Connect AD0 and AD2
to either GND, V+, SCL, or SDA to give four logic combinations (see Tables 2 and 3).
4, 5, 10,
11, 13–20
1, 2, 7, 8,
10–17
O0, O1,
O6–O15 Output Ports. O0, O1, O6–O15 are push-pull outputs rated at 20mA.
6–9 3–6 P2–P5 P2–P5 Open-Drain I/Os
12 9 GND Ground
22 19 SCL I2C-Compatible Serial Clock Input
23 20 SDA I2C-Compatible Serial Data I/O
24 21 V+ Positive Supply Voltage. Bypass V+ to GND with a 0.047µF ceramic capacitor.
EP EP Exposed Pad. Connect exposed pad to GND.
OUTPUT VOLTAGE HIGH
vs. TEMPERATURE
TEMPERATURE (°C)
OUTPUT VOLTAGE HIGH (V)
MAX7327 toc04
-40 -25 -10 5 20 35 50 65 80 95 110 125
0
1
2
3
4
5
6
V+ = +3.3V
ISOURCE = 5mA
V+ = +5.0V
ISOURCE = 10mA
V+ = +2.5V ISOURCE = 5mA
V+ = +1.71V ISOURCE = 2mA
OUTPUT VOLTAGE LOW
vs. TEMPERATURE
TEMPERATURE (°C)
OUTPUT VOLTAGE LOW (V)
MAX7327 toc03
-40 -25 -10 5 20 35 50 65 80 95 110 125
0
0.05
0.10
0.15
0.20
0.25
V+ = +3.3V
ISINK = 15mA
V+ = +5.0V
ISINK = 20mA
V+ = +2.5V
ISINK = 10mA
V+ = +1.71V
ISINK = 5mA
V+ = +1.62V
ISINK = 4mA
SUPPLY CURRENT
vs. TEMPERATURE
TEMPERATURE (°C)
SUPPLY CURRENT (A)
MAX7327 toc02
-40 -25 -10 5 20 35 50 65 80 95 110 125
0
10
20
30
40
50
60
V+ = +3.3V
V+ = +5.0V
V+ = +2.5V
V+ = +1.71V
fSCL = 400kHz
STANDBY CURRENT
vs. TEMPERATURE
TEMPERATURE (°C)
STANDBY CURRENT (A)
MAX7327 toc01
-40 -25 -10 5 20 35 50 65 80 95 110 125
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
V+ = +3.3V
V+ = +5.0V
V+ = +2.5V
V+ = +1.71V
fSCL = 0kHz
Maxim Integrated
4
www.maximintegrated.com
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Pin Description
Typical Operating Characteristics
Detailed Description
MAX7319MAX7329 Family Comparison
The MAX7324–MAX7327 family consists of four pin-
compatible, 16-port expanders that integrate the
functions of the MAX7320 and one of either the MAX7319,
MAX7321, MAX7322, or MAX7323.
Functional Overview
The MAX7327 is a general-purpose port expander
operating from a +1.71V to +5.5V supply that provides
12 push-pull output ports with a 20mA sink, 10mA
source drive capability, and four open-drain I/O ports
with a 20mA sink capability. The four open-drain out-
puts are overvoltage protected to +6V.
The MAX7327 is set to two of 32 I2C slave addresses
(see Tables 2 and 3) using address inputs AD2 and AD0,
and is accessed over an I2C serial interface up to 400kHz.
Eight push-pull outputs use a different slave address from
the other four push-pull outputs and the open-drain I/Os.
The eight push-pull outputs (O8–O15) use the 101xxxx
addresses while the four outputs (O0, O1, O6, and O7)
and the open-drain I/Os (P2–P5) use addresses with
110xxxx. The RST input clears the serial interface in case
of a bus lockup, terminating any serial transaction to or
from the MAX7327.
Any of the four open-drain ports can be configured as a
logic input by setting the port output logic-high (logic-high
for an open-drain output is high impedance). When the
MAX7327 is read through the serial interface, the actual
logic levels at the ports are read back.
Table 1. MAX7319MAX7329 Family Comparison
PART
I2C
SLAVE
ADDRESS
INPUTS
INPUT
INTERRUPT
MASK
OPEN-
DRAIN
OUTPUTS
PUSH-
PULL
OUTPUTS
CONFIGURATION
16-PORT EXPANDERS
MAX7324
101xxxx
and
110xxxx
8 Yes 8
8 inputs and 8 push-pull outputs version:
8 input ports with programmable latching transition
detection interrupt and selectable pullups.
8 push-pull outputs with selectable default logic
levels.
Offers maximum versatility for automatic input
monitoring. An interrupt mask selects which inputs
cause an interrupt on transitions, and transition flags
identify which inputs have changed (even if only for
a transient) since the ports were last read.
MAX7325 Up to 8 Up to 8 8
8 I/O and 8 push-pull outputs version:
8 open-drain I/O ports with latching transition
detection interrupt and selectable pullups.
8 push-pull outputs with selectable default logic
levels.
Open-drain outputs can level shift the logic-high state
to a higher or lower voltage than V+ using external
pullup resistors, but pullups draw current when output
is low. Any open-drain port can be used as an input
by setting the open-drain output to logic-high.
Transition flags identify which open-drain port inputs
have changed (even if only for a transient) since the
ports were last read.
www.maximintegrated.com Maxim Integrated
5
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Table 1. MAX7319MAX7329 Family Comparison (continued)
PART
I2C
SLAVE
ADDRESS
INPUTS
INPUT
INTERRUPT
MASK
OPEN-
DRAIN
OUTPUTS
PUSH-
PULL
OUTPUTS
CONFIGURATION
MAX7326
101xxxx
and
110xxxx
4 Yes 12
4 input-only, 12 push-pull output versions:
4 input ports with programmable latching transition
detection interrupt and selectable pullups.
12 push-pull outputs with selectable default logic
levels.
Offers maximum versatility for automatic input
monitoring. An interrupt mask selects which inputs
cause an interrupt on transitions, and transition flags
identify which inputs have changed (even if only for
a transient) since the ports were last read.
MAX7327 Up to 4 Up to 4 12
4 I/O, 12 push-pull output versions:
4 open-drain I/O ports with latching transition
detection interrupt and selectable pullups.
12 push-pull outputs with selectable default logic
levels.
Open-drain outputs can level shift the logic-high state
to a higher or lower voltage than V+ using external
pullup resistors, but pullups draw current when output
is low. Any open-drain port can be used as an input
by setting the open-drain output to logic-high.
Transition flags identify which open-drain port inputs
have changed (even if only for a transient) since the
ports were last read.
8-PORT EXPANDERS
MAX7319 110xxxx 8 Yes
Input-only versions:
8 input ports with programmable latching transition
detection interrupt and selectable pullups.
MAX7320 101xxxx 8
Output-only versions:
8 push-pull outputs with selectable power-up default
levels.
MAX7321 110xxxx Up to 8 Up to 8
I/O versions:
8 open-drain I/O ports with latching transition
detection interrupt and selectable pullups.
MAX7322 110xxxx 4 Yes 4
4 input-only, 4 output-only versions:
4 input ports with programmable latching transition
detection interrupt and selectable pullups.
4 push-pull outputs with selectable power-up default
levels.
www.maximintegrated.com Maxim Integrated
6
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
The four open-drain ports offer latching transition
detection functionality when used as inputs. All input ports
are continuously monitored for changes. An input change
sets 1 of 4 flag bits that identify the changed input(s). All
flags are cleared upon a subsequent read or write trans-
action to the MAX7327.
A latching interrupt output (INT) automatically flags data
changes on any of the I/O ports used as inputs through
an interrupt mask register. Data changes on any input
port forces INT to a logic-low. Interrupt output INT is
deasserted when the MAX7327 is next accessed through
the serial interface.
Internal pullup resistors to V+ are selected by the address
select inputs, AD0 and AD2. Pullups are enabled on the
input ports in groups of two (see Table 2). Use the slave
address selection to ensure that I/O ports used as inputs
are logic-high on power-up. I/O ports with internal pullups
enabled default to a logic-high output state. I/O ports
with internal pullups disabled default to a logic-low output
state.
Output port power-up logic levels are selected by the
address select inputs (AD0 and AD2). Ports default to
logic-high or logic-low on power-up in groups of two (see
Tables 2 and 3).
Initial Power-Up
On power-up, the default states of the 12 push-pull
output ports and the four open-drain I/O ports are set
according to the I2C slave address selection inputs,
AD0 and AD2 (see Tables 2 and 3). For I/O ports
used as inputs, ensure that the default states are
logic-high; therefore, the I/O ports power up in the
high-impedance state. All I/O ports configured with pullups
enabled also have a logic-high default state. On power-
up, the transition detection logic is reset, and INT is
deasserted. The transition flags are cleared, indicating no
data changes.
Power-On Reset (POR)
The MAX7327 contains an integral POR circuit that
ensures all registers are reset to a known state on
power-up. When V+ rises above VPOR (1.6V max), the
POR circuit releases the registers and 2-wire interface
for normal operation. When V+ drops to less than VPOR,
the MAX7327 resets all register contents to the POR
defaults (Tables 2 and 3).
RST Input
The active-low reset input (RST) operates as a hardware
reset that voids any I2C transaction involving the MAX7327,
forcing the MAX7327 into the I2C STOP condition. A
reset does not affect the interrupt output (INT).
Standby Mode
When the serial interface is idle, the MAX7327
automatically enters standby mode, drawing minimal
supply current.
Slave Address, Power-Up Default Logic
Levels, and Input Pullup Selection
Address inputs AD0 and AD2 determine the MAX7327
slave address and select which inputs have pullup
resistors. Pullups are enabled on the input ports in groups
of two (see Table 2).
The MAX7327 slave address is determined on each I2C
transmission, regardless of whether the transmission
is actually addressing the MAX7327. The MAX7327
distinguishes whether address inputs AD0 and AD2 are
connected to SDA or SCL instead of fixed-logic levels V+
or GND during the transmission. The MAX7327 slave
Table 1. MAX7319MAX7329 Family Comparison (continued)
PART
I2C
SLAVE
ADDRESS
INPUTS
INPUT
INTERRUPT
MASK
OPEN-
DRAIN
OUTPUTS
PUSH-
PULL
OUTPUTS
CONFIGURATION
MAX7323 110xxxx Up to 4 Up to 4 4
4 I/O, 4 output-only versions:
4 open-drain I/O ports with latching transition
detection interrupt and selectable pullups.
4 push-pull outputs with selectable power-up default
levels.
MAX7328
MAX7329
0100xxx
0111xxx Up to 8 Up to 8
PCF8574-, PCF8574A-compatible versions:
8 open-drain I/O ports with nonlatching transition
detection interrupt and pullups on all ports.
www.maximintegrated.com Maxim Integrated
7
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
address can be configured dynamically in the application
without cycling the device supply.
On initial power-up, the MAX7327 cannot decode the
address inputs AD0 and AD2 fully until the first I2C trans-
mission. AD0 and AD2 initially appear to be connected
to V+ or GND. This is important because the address
selection is used to determine the power-up default states
of the output ports, I/O port initial logic state, and whether
pullups are enabled. At power-up, the I2C SDA and SCL
bus interface lines are high impedance at the I/O pins
of every device (master or slave) connected to the bus,
including the MAX7327. This is guaranteed as part of the
I2C specification. Therefore, when address inputs AD0
and AD2 are connected to SDA or SCL during power-up,
they appear to be connected to V+. The pullup selection
logic uses AD0 to select whether pullups are enabled
for ports P2 and P3, and uses AD2 to select whether
pullups are enabled for ports P4 and P5. The rule is that
a logic-high, SDA, or SCL connection selects the pullups
and sets the logic state to high. A logic-low deselects the
pullups and sets the default logic state to low. The pullup
configuration is correct on power-up for a standard I2C
configuration, where SDA or SCL are pulled up to V+ by
the external I2C pullup resistors.
There are circumstances where the assumption that
SDA = SCL = V+ on power-up is not true; for example, in
applications in which there is legitimate bus activity during
power-up. If SDA and SCL are terminated with pullup
resistors to a different supply voltage to the MAX7327’s
supply voltage, and if that pullup supply rises later than
the MAX7327’s supply, then SDA or SCL may appear at
power-up to be connected to GND. In such applications,
use the four address combinations that are selected by
connecting address inputs AD0 and AD2 to V+ or GND
(shown in bold in Tables 2 and 3). These selections are
guaranteed to be correct at power-up, independent of
SDA and SCL behavior. If one of the other 12 address
combinations is used, an unexpected combination of
pullups might be asserted until the first I2C transmission
(to any device, not necessarily the MAX7327) is put on
the bus.
Table 2. MAX7327 Address Map for Outputs O0, O1, O6, O7, and Ports P2P5
PIN
CONNECTION DEVICE ADDRESS PORTS POWER-UP DEFAULT 40k INPUT PULLUPS ENABLED
AD2 AD0 A6 A5 A4 A3 A2 A1 A0 O7 O6 P5 P4 P3 P2 O1 O0 O7 O6 P5 P4 P3 P2 O1 O0
SCL GND 1 1 0 0 0 0 0 1 1 1 1 0 0 0 0
Pullups are not enabled for push-pull outputs
Y Y
Pullups are not enabled for push-pull outputs
SCL V+ 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 Y Y Y Y
SCL SCL 1 1 0 0 0 1 0 1 1 1 1 1 1 1 1 Y Y Y Y
SCL SDA 1 1 0 0 0 1 1 1 1 1 1 1 1 1 1 Y Y Y Y
SDA GND 1 1 0 0 1 0 0 1 1 1 1 0 0 0 0 Y Y
SDA V+ 1 1 0 0 1 0 1 1 1 1 1 1 1 1 1 Y Y Y Y
SDA SCL 1 1 0 0 1 1 0 1 1 1 1 1 1 1 1 Y Y Y Y
SDA SDA 1 1 0 0 1 1 1 1 1 1 1 1 1 1 1 Y Y Y Y
GND GND 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0
GND V+ 1 1 0 1 0 0 1 0 0 0 0 1 1 1 1 Y Y
GND SCL 1 1 0 1 0 1 0 0 0 0 0 1 1 1 1 Y Y
GND SDA 1 1 0 1 0 1 1 0 0 0 0 1 1 1 1 Y Y
V+ GND 1 1 0 1 1 0 0 1 1 1 1 0 0 0 0 Y Y
V+ V+ 1 1 0 1 1 0 1 1 1 1 1 1 1 1 1 Y Y Y Y
V+ SCL 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 Y Y Y Y
V+ SDA 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 Y Y Y Y
www.maximintegrated.com Maxim Integrated
8
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
I/O Port Inputs
I/O port inputs switch at CMOS logic levels as determined
by the expanders supply voltage, and are overvoltage
tolerant to +6V, independent of the expanders supply
voltage.
I/O Port Input Transition Detection
All I/O ports configured as inputs are monitored for
changes since the expander was last accessed through
the serial interface. The state of the ports is stored in
an internal “snapshot” register for transition monitoring.
The snapshot is continuously compared with the actual
input conditions, and if a change is detected for any port
input, INT is asserted to signal a state change. The input
ports are sampled (internally latched into the snapshot
register) and the old transition flags cleared during the I2C
acknowledge of every MAX7327 read and write access.
The previous port-transition flags are read through the
serial interface as the second byte of a 2-byte read
sequence.
A long read sequence (more than 2 bytes) can be used
to poll the expander continuously without the overhead
of resending the slave address. If more than 2 bytes are
read from the expander, the expander repeatedly returns
the 2 bytes of input port data followed by the transition
flags. The inputs are repeatedly resampled and the
transition flags repeatedly reset for each pair of bytes
read. All changes that occur during a long read sequence
are detected and reported.
The INT output is not reasserted during a read sequence
to avoid recursive reentry into an interrupt service
routine. Instead, if a data change occurs that would
normally cause the INT output to be set, the INT assertion
is delayed until the STOP condition. INT is not reassert-
ed upon a STOP condition if the changed input data is
read before the STOP occurs. The INT logic ensures
that unnecessary interrupts are not asserted, yet data
changes are detected and reported no matter when the
change occurs.
Table 3. MAX7327 Address Map for Outputs O8O15
PIN
CONNECTION DEVICE ADDRESS OUTPUTS POWER-UP DEFAULT
AD2 AD0 A6 A5 A4 A3 A2 A1 A0 O15 O14 O13 O12 O11 O10 O9 O8
SCL GND 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0
SCL V+ 1 0 1 0 0 0 1 1 1 1 1 1 1 1 1
SCL SCL 1 0 1 0 0 1 0 1 1 1 1 1 1 1 1
SCL SDA 1 0 1 0 0 1 1 1 1 1 1 1 1 1 1
SDA GND 1 0 1 0 1 0 0 1 1 1 1 0 0 0 0
SDA V+ 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1
SDA SCL 1 0 1 0 1 1 0 1 1 1 1 1 1 1 1
SDA SDA 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1
GND GND 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0
GND V+ 1 0 1 1 0 0 1 0 0 0 0 1 1 1 1
GND SCL 1 0 1 1 0 1 0 0 0 0 0 1 1 1 1
GND SDA 1 0 1 1 0 1 1 0 0 0 0 1 1 1 1
V+ GND 1 0 1 1 1 0 0 1 1 1 1 0 0 0 0
V+ V+ 101110111111111
V+ SCL 1 0 1 1 1 1 0 1 1 1 1 1 1 1 1
V+ SDA 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1
www.maximintegrated.com Maxim Integrated
9
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Serial Interface
Serial Addressing
The MAX7327 operates as a slave that sends and
receives data through an I2C interface. The interface uses
a serial-data line (SDA) and a serial-clock line (SCL) to
achieve bidirectional communication between master(s)
and slave(s). The master initiates all data transfers to
and from the MAX7327 and generates the SCL clock that
synchronizes the data transfer (Figure 1).
SDA operates as both an input and an open-drain output.
A pullup resistor, typically 4.7k, is required on SDA.
SCL operates only as an input. A pullup resistor, typically
4.7k, is required on SCL if there are multiple masters
on the 2-wire interface, or if the master in a single-master
system has an open-drain SCL output.
Each transmission consists of a START condition sent
by a master, followed by the MAX7327’s 7-bit slave
addresses plus R/W bits, one or more data bytes, and
finally a STOP condition (Figure 2).
START and STOP Conditions
Both SCL and SDA remain high when the interface
is not busy. A master signals the beginning of a trans-
mission with a START (S) condition by transitioning
SDA from high to low while SCL is high. When the
master has finished communicating with the slave, the
master issues a STOP (P) condition by transitioning
SDA from low to high while SCL is high. The bus is then
free for another transmission (Figure 2).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on SDA must remain stable while SCL is high
(Figure 3).
Figure 3. Bit Transfer
Figure 2. Start and Stop Conditions
Figure 1. 2-Wire Serial Interface Timing Details
SDA
SCL
DATA LINE STABLE;
DATA VALID
CHANGE OF DATA
ALLOWED
SDA
SCL
START
CONDITION
STOP
CONDITION
S P
SCL
SDA
tRtF
tBUF
START
CONDITION
STOP
CONDITION
REPEATED START CONDITION
START CONDITION
tSU,STO
tHD,STA
tSU,STA
tHD,DAT
tSU,DAT
tLOW
tHIGH
tHD,STA
www.maximintegrated.com Maxim Integrated
10
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Acknowledge
The acknowledge bit is a clocked 9th bit the recipient
uses to acknowledge receipt of each byte of data (Figure
4). Each byte transferred effectively requires 9 bits. The
master generates the 9th clock pulse, and the recipient
pulls down SDA during the acknowledge clock pulse,
such that the SDA line is stable low during the high period
of the clock pulse. When the master is transmitting to the
MAX7327, the MAX7327 generates the acknowledge bit
because the device is the recipient. When the MAX7327
is transmitting to the master, the master generates the
acknowledge bit because the master is the recipient.
Slave Address
The MAX7327 has two different 7-bit slave addresses
(Figure 5). The addresses are different to communicate
to the eight push-pull outputs (O8–O15) or the other eight
I/Os. The eighth bit following the 7-bit slave address is
the R/W bit. It is low for a write command and high for a
read command.
The first (A6), second (A5), and third (A4) bits of the
MAX7327 slave address are always 1, 1, and 0 (O0,
O1, P2–P5, O6, O7) or 1, 0, and 1 (O8–O15). Connect
AD0 and AD2 to GND, V+, SDA, or SCL to select slave
address bits A3, A2, A1, and A0. The MAX7327 has 16
possible slave addresses (Tables 2 and 3), allowing up to
16 MAX7327 devices on an I2C bus.
Accessing the MAX7327
The MAX7327 is a combination of MAX7320 and
MAX7323. The group A of eight ports (O0, O1, P2–P5,
O6, and O7) corresponding to those of the MAX7323 and
the group B of eight ports (O8–O15) corresponding to
those of the MAX7320 are read/write separately through
their own addresses, as shown by Tables 2 and 3, respec-
tively.
A single-byte read from the group A ports of the
MAX7327 returns the status of the four I/O ports and the
four output ports (read back as inputs), and clear both
the internal transition flags and the INT output when the
master acknowledges the slave address byte.
A 2-byte read from the group A ports of the MAX7327
returns the status of the four I/O ports and the four output
ports (as for a single byte read), followed by the four tran-
sition flags for the four I/O ports. The internal transition
flags and the INT output are cleared automatically when
the master acknowledges the slave address byte (but the
previous transition flag data is sent as the second byte).
A multibyte read (more than 2 bytes before the I2C STOP
bit) from the group A ports of the MAX7327 repeatedly
returns the port data, alternating with the transition flags.
As the port data is resampled for each transmission, and
the transition flags are reset each time, a multibyte read
continuously returns the current data and identifies any
changing I/O ports.
If a port input data change occurs during the read
sequence, then INT is reasserted during the I2C STOP
bit. The MAX7327 does not generate another interrupt
during a single-byte or multibyte MAX7327 read routine.
Input port data is sampled during the preceding I2C
acknowledge bit (the acknowledge bit for the I2C slave
address in the case of a single-byte or 2-byte read).
Figure 5. Slave Address
Figure 4. Acknowledge
SDA
SCL
A5
MSB LSB
ACKA4 A11 A3 A0A2 R/W
SCL
SDA BY
TRANSMITTER
CLOCK PULSE
FOR ACKNOWLEDGEMENT
START
CONDITION
SDA BY
RECEIVER
1 2 8 9
S
www.maximintegrated.com Maxim Integrated
11
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
A single-byte read from the group B ports of the
MAX7327 returns the status of the eight output ports, read
back as inputs.
A 2-byte read from the group B ports of the MAX7327
repeatedly returns the status of the eight output ports,
read back as inputs.
A multibyte read (more than 2 bytes before the I2C
STOP bit) from the group B ports of the MAX7327 repeat-
edly returns the status of the eight output ports, read back
as inputs.
A single-byte write to the group A or B ports of the
MAX7327 sets the logic state of all eight ports.
A multibyte write to the group A or B ports of the
MAX7327 repeatedly sets the logic state of all eight ports.
Reading the MAX7327
A read from the group A ports of the MAX7327 starts with
the master transmitting the port group’s slave address
with the R/W bit set to high. The MAX7327 acknowledges
the slave address, and samples the status of the ports
during the acknowledge bit. INT goes high during the
slave address acknowledge. The master can then issue
a STOP condition after the acknowledge. The snapshot
is taken, and the INT status remains unchanged, if the
master terminates the serial transition with a no-
acknowledge.
When the master reads one byte from the group A
ports of the MAX7327 and subsequently issues a STOP
condition (Figure 6), the MAX7327 transmits the current
port data, clears the change flags, and resets the tran-
Figure 6. Reading Group A Ports of the MAX7327 (1 Data Byte)
SCL
MAX7327 SLAVE ADDRESS
S A P
1
PORTS
ACKNOWLEDGE FROM MAX7327
NO ACKNOWLEDGE
FROM MASTER
PORT SNAPSHOT
tIV
tPH
tIR
N
O0O1P2P3P4P5O6O7
D0D1D2D3D4D5D6D7
PORT SNAPSHOT
tPS tIP
INT REMAINS HIGH UNTIL STOP CONDITION
INT OUTPUT
R/W
www.maximintegrated.com Maxim Integrated
12
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
sition detection. INT deasserts during the slave
acknowledge. The new snapshot data is the current
port data transmitted to the master, and therefore, port
changes occuring during the transmission are detected.
INT remains high until the STOP condition.
When the master reads 2 bytes from the group A ports
of the MAX7327 and subsequently issues a STOP con-
dition (Figure 7), the MAX7327 transmits the current
port data, followed by the change flags. The change
flags are then cleared, and transition detection is reset.
INT goes high (high impedance if an external pullup
resistor is not fitted) during the slave acknowledge. The
new snapshot data is the current port data transmitted
to the master, and therefore, port changes occuring
during the transmission are detected. INT remains high
until the STOP condition.
A read from the group B ports of the MAX7327 starts
with the master transmitting the group’s slave address
with the R/W bit set high. The MAX7327 acknowledges
the slave address, and samples the logic state of the
output ports during the acknowledge bit. The master can
read one or more bytes from the group B ports of the
MAX7327 and then issue a STOP condition (Figure 8).
The MAX7327 transmits the current port data, read back
from the actual port outputs (not the port output latches)
during the acknowledge. If a port is forced to a logic
state other than its programmed state, the readback
reflects this. If driving a capacitive load, the readback
port-level verification algorithms may need to take the
RC rise/fall time into account.
Typically, the master reads one byte from the group B
ports of the MAX7327, then issues a STOP condition
(Figure 8). However, the master can read two or more
Figure 8. Reading Group B Ports of MAX7327
Figure 7. Reading Group A Ports of the MAX7327 (2 Data Bytes)
SCL
MAX7327 SLAVE ADDRESS
S A P
1
ACKNOWLEDGE FROM MAX7327
PORT SNAPSHOT DATA
PORT SNAPSHOT TAKEN
A
P0P1P2P3
DATA 1
P4P5P6P7
D0D1D2D3D4D5D6D7
PORT SNAPSHOT TAKEN ACKNOWLEDGE
FROM MASTER
R/W
SCL
MAX7327 SLAVE ADDRESSS A P1
PORTS
INT OUTPUT
R/W
ACKNOWLEDGE FROM MAX7327
PORT SNAPSHOT
tIV
tPH
tIR
A
O7 O6 P4P5 P3 P2 O1 O0
D0D1D2D3D4D5D6D7
PORT SNAPSHOT
tPS tIP
F0
F1
F2F3F4F5
F6
F7
D7 D6 D5 D4 D3 D2 D1 D0 N
PORT SNAPSHOT
FLAG
NO ACKNOWLEDGE
FROM MASTER
INT REMAINS HIGH UNTIL STOP CONDITION
www.maximintegrated.com Maxim Integrated
13
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
bytes from the group B ports of the MAX7327, then issue
a STOP condition. In this case, the MAX7327 resamples
the port outputs during each acknowledge and transmits
the new data each time.
Writing to the MAX7327
A write to the group A or B ports of the MAX7327 starts
with the master transmitting the group’s slave address
with the R/W bit set low. The MAX7327 acknowledges the
slave address and samples the ports during the acknowl-
edge bit. INT goes high (high impedance if an external
pullup resistor is not fitted) during the slave acknowledge
only when it writes to the group A ports. The master can
now transmit one or more bytes of data. The MAX7327
acknowledges these subsequent bytes of data and
updates the corresponding group’s ports with each new
byte until the master issues a STOP condition (Figure 9).
Applications Information
Port Input and I2C Interface Level
Translation from Higher
or Lower Logic Voltages
The MAX7327’s SDA, SCL, AD0, AD2, RST, INT, and
the four I/O ports (P2–P5) are overvoltage protected
to +6V, independent of V+. This allows the MAX7327
to operate from a lower supply voltage, such as +3.3V,
while the I2C interface and/or some of the four I/O ports
are driven from a higher logic level, such as +5V.
The MAX7327 can operate from a higher supply volt-
age, such as +3V, while the I2C interface and/or some
of the four I/O ports (P2–P5) are driven from a lower
logic level, such as +2.5V. For V+ < 1.8V, apply a min-
imum voltage of 0.8 x V+ to assert a logic-high on any
input. For a V+ 1.8V, apply a voltage of 0.7 x V+ to
assert a logic-high. For example, a MAX7327 operating
from a +5V supply may not recognize a +3.3V nominal
logic-high. One solution for input-level translation is to
drive MAX7327 inputs from open-drain outputs. Use a
pullup resistor to V+ or a higher supply to ensure a high
logic voltage greater than 0.7 x V+.
Port Output Signal Level Translation
The open-drain output architecture allows for level
translation to higher or lower voltages than the
MAX7327’s supply. Use an external pullup resistor on
any output to convert the high-impedance logic-high
condition to a positive voltage level. The resistor can be
connected to any voltage up to +6V, and the resistor
value chosen to ensure no more than 20mA to be
sunk in logic-low condition. For interfacing CMOS
inputs, a pullup resistor value of 220k is a good
starting point. Use a lower resistance to improve noise
immunity, in applications where power consumption is less
critical, or where a faster rise time is needed for a given
capacitive load.
Each of the 12 push-pull output ports has protection
diodes to V+ and GND. When a port output is driven to
a voltage higher than V+ or lower than GND, the appro-
priate protection diode clamps the output to a diode drop
above V+ or below GND. When the MAX7327 is powered
down (V+ = 0V), every output port’s protection diodes to
Figure 9. Writing the MAX7327
SCL
SDA
START CONDITION R/WACKNOWLEDGE
FROM SLAVE
SLAVE ADDRESS
S 0
1 2 3 4 5 6 7 8
A A A
tPV
DATA 1 DATA 2
DATA 2 VALIDDATA 1 VALID
WRITE
TO PORT
DATA OUT
FROM PORT
ACKNOWLEDGE
FROM SLAVE
ACKNOWLEDGE
FROM SLAVE
tPV
DATA TO PORT DATA TO PORT
www.maximintegrated.com Maxim Integrated
14
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
V+ and GND continue to appear as a diode clamp from
each output to GND (Figure 10).
Each of the four P2–P5 I/O ports has a protection diode
to GND (Figure 11). When a port output is driven to a
voltage lower than GND, the protection diode clamps
the output to a diode drop below GND.
Each of the four P2 –P5 I/O ports also has a 40k (typ)
pullup resistor that can be enabled or disabled. When a
port input is driven to a voltage higher than V+, the
body diode of the pullup enable switch conducts and
the 40k pullup resistor is enabled. When the
MAX7327 is powered down (V+ = 0V), each I/O port
appears as a 40k resistor in series with a diode con-
nected to 0V. Input ports are protected to +6V under
any of these circumstances (Figure 11).
Driving LED Loads
When driving LEDs from one of the 12 push-pull out-
puts, a resistor must be fitted in series with the LED to
limit the LED current to no more than 20mA. Connect
the LED cathode to the MAX7327 port, and the LED
anode to V+ through the series current-limiting resistor,
RLED. Set the port output low to light the LED. Choose
the resistor value according to the following formula:
RLED = (VSUPPLY - VLED - VOL) / ILED
where:
RLED is the resistance of the resistor in series with the
LED ().
VSUPPLY is the supply voltage used to drive the LED (V).
VLED is the forward voltage of the LED (V).
VOL is the output low voltage of the MAX7327 when sink-
ing ILED (V).
ILED is the desired operating current of the LED (A).
For example, to operate a 2.2V red LED at 10mA from a
+5V supply:
RLED = (5 - 2.2 - 0.1) / 0.01 = 270
Driving Load Currents Higher than 20mA
The MAX7327 can be used to drive loads such as relays
that draw more than 20mA by paralleling outputs. Use at
least one output per 20mA of load current; for example,
a 5V 330mW relay draws 66mA, and therefore, requires
four paralleled outputs. Any combination of outputs can
be used as part of a load-sharing design because any
combination of ports can be set or cleared at the same
time by writing to the MAX7327. Do not exceed a total
sink current of 100mA for the device.
The MAX7327 must be protected from the negative
voltage transient generated when switching off induc-
tive loads (such as relays), by connecting a reverse-
biased diode across the inductive load. Choose the peak
current for the diode to be greater than the inductive load’s
operating current.
Power-Supply Considerations
The MAX7327 operates with a supply voltage of +1.71V
to +5.5V. Bypass the supply to GND with a ceramic
capacitor of at least 0.047µF as close as possible to the
device. For the TQFN version, additionally connect the
exposed pad to GND.
Figure 11. MAX7327 Open-Drain I/O Port StructureFigure 10. MAX7327 Push-Pull Output Port Structure
P2–P5
PULLUP
ENABLE
INPUT
OUTPUT
40k
MAX7327
V+ V+
OUTPUT
V+V+
O0–O2
O6–O15
MAX7327
www.maximintegrated.com Maxim Integrated
15
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND PATTERN
NO.
24 QSOP E24+1 21-0055 90-0172
24 TQFN
(4mm x 4mm) T2444+3 21-0139
24 TQFN
(3.5mm x 3.5mm) T243A3+1 21-0188 90-0122
MAX7327
P2
O7
O6
P5
P4
O11
O10
O9
O8
O15
O14
013
012
V+
GND
3.3V
µC
SCL SCL
SDA
AD0 O2
O1
SDA
P3
AD2
INT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
RST
INT
RST
INPUT/OUTPUT
INPUT/OUTPUT
INPUT/OUTPUT
INPUT/OUTPUT
TOP VIEW
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
INT V+
SDA
SCL
AD0
O15
O14
O13
O12
MAX7327
QSOP
RST
AD2
P2
O0
O1
P3
P4
16
15
9
10
O11
O10
P5
O6
14
13
11
12
O9
O8
O7
GND
+
I2C
CONTROL
O9
O8
O11
O10
O12
O13
O14
O15
O1
O0
P3
P2
P4
P5
O6
O7
INT
I/O
PORTS
POWER-ON
RESET
INPUT
FILTER
RST
SDA
SCL
AD2
AD0
MAX7327
www.maximintegrated.com Maxim Integrated
16
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
Chip Information
PROCESS: BiCMOS
Typical Application Circuit
Pin Congurations (continued)
Functional Diagram
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 8/06 Initial release
1 7/14 No /V OPNs; removed automotive reference from Applications section; updated
Package Information 1, 18–20
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2014 Maxim Integrated Products, Inc.
17
MAX7327 I2C Port Expander with 12 Push-Pull
Outputs and 4 Open-Drain I/Os
Revision History
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
MAX7327AATG+T MAX7327AATG+