SOLID STATE RELAY 1 Maximum Load current 1A FTR - SL SERIES RoHS compliant n FEATURES Ultra slim and light weight, SIL terminal type -- size: 5.0 (W) x 28.0 (L) x 15.0 (H): 140mm mounting area -- weight: approximately 4.0g l Internal varistor and snubber circuit l High insulation (between input and output) - dielectric strength 2500Vrms l Include a zero cross circuit as standard equipment l High frequency switching, long life and maintenance free l High impact/vibration resistance, good for automatic assembly, washable l RoHS compliant since date code: 6522 Please see page 5 for more information l n ORDERING INFORMATION [Example] FTR-SL (a) P (b) K (c) 024 W (d) (e) (a) Series Name FTR-SL : FTR-SL Series (b) Load Voltage P : AC type (c) Input or Output Type K : Output type (d) Nominal Voltage 005 012 024 060 : 5 VDC : 12 VDC : 24VDC : 60 VDC (e) W : With Zero Cross Circuit and Varistor Zero Cross Circuit Output Protection Note: The part number on the relay cover does not include 'FTR' Example: Ordering part number: FTR-SL-PK012W Stamped part number: SLPK012W FTR-SL SERIES n SPECIFICATION Item Iput side Outpt side Temperature Time Insulation FTR-SLPK005 W FTR-SLPK012 W FTR-SLPK024 W FTR-SLPK060 W Nominal Voltage 5 VD C 12 VD C 24 VD C 60 VD C Operate Range 3.75 to 6 VD C 9 to 14.4 VD C 18 to 28.8 VD C 48 to 66 VD C Must operate voltage 3.75 VDC 9.0 VD C 18 VD C 48 VD C Must release voltage 1.25 VDC 3.6 VD C 8.4 VD C 18 VD C Input Impedance 560 10 % 1.3K 10 % 2.4K 10 % 10K 10 % Load voltage range 24 to 250 AC Vrms Max. load current 1 Arm s 1 cycle surge current 50 A (60 Hz, 1 cycle) max. off-state leakage current max. 1 mArms (60Hz, 220 AC Vrms) max. on-state voltage drop max. 1.3 V (1Arms, 50Hz) Storage temperature range -40 to +100 C (no frost) Operating temperature range -30 to +85 C (no frost) Max. operating time max. 1/2 cycle + 1ms Max. release time max. 1/2 cycle + 1m s Insulation resistance min. 1000M (at 500 VDC) Dielectric strength min. 2500 Vrms (1 minute ) Output protection Other Snubber circuit and varisto r Case color Blac k weight Approximately 4.0g FTR-SL SERIES n BLOCK DIAGRAM 2 Phototriac coupler Input Input terminal circuit 1 ~4 Snubber circuit Phototriac coupler Input/Output Waveform (resistive load) Circuit Output triac AC type Insulaton Trigger circuit Load Output terminal Source voltage of load ON Input signal OFF Load current ~3 n CHARACTERISTIC DATA Maximum Load Current (A) 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -40 -20 0 20 40 60 80 100 Ambient Temperature (C) FTR-SL SERIES n DIMENSIONS 5+0 3.5 15+0 28+0 2-0.5 2-1 (1.9) 5.04 0.4 (1.2) 3.78 16.38 * PC board mounting hole layout (bottom view) * Schematic (bottom view) 2 3 ~ ~ OUTPUT 16.380.1 1 3.7801 1.2 4 1.9 5.040.1 + INPUT 2-O1.30.1 2-O0.90.1 Unit: mm n NOTES Polarity of terminals are pre-determined. Please design your circuit accordingly. n PACKAGE Style Quantity/tube (pcs ) MOQ (pcs ) Tube 15 30 0 FTR-SL SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l "LF" is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile Recommended solder paste Sn-3.0Ag-0.5Cu. l Reflow Solder condtion Flow Solder condtion: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. 4. Tin Whisker l Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. FTR-SL SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141 8630, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@fcl.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2006 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. August 1/2006