Supertex inc. MD1810 High Speed Quad MOSFET Driver Features General Description 6.0ns rise and fall time with 1000pF load 2.0A peak output source/sink current 1.8 to 5.0V input CMOS compatible 5.0 to 12V total supply voltage Smart logic threshold Low jitter design Four matched channels Outputs can swing below ground Output is high impedence when disabled Low inductance package High-performance thermally-enhanced QFN The Supertex MD1810 is a high-speed quad MOSFET driver. It is designed to drive high voltage P- and N-channel MOSFETs for medical ultrasound imaging applications. The MD1810 can also be used for ultrasound metal flaw detection, Non-Destructive Testing (NDT), piezoelectric transducer drive, clock drive, and PIN diode drive. The MD1810 has four inputs which individually control four outputs. It also has an output enable (OE) pin. When OE is low, all of the outputs will be in a high impedence state regardless of their logic input control. When OE is high, the MD1810 sets the threshold logic transition to (VOE+VGND)/2. This ensures the transition to always be at half the amplitude of the logic input signal. This allows the device to have inherent propagation delay matching regardless of the logic input amplitude. Applications Medical ultrasound imaging Piezoelectric transducer drivers Non-Destructive Testing (NDT) PIN diode driver CCD Clock driver/buffer High speed level translator The output stage of the MD1810 has separate power connections enabling the output signal L and H levels to be chosen independently from the VDD and VSS supply voltages. As an example, the input logic levels may be 0 and 1.8V, the control logic may be powered by +5.0 and -5.0V, and the output L and H levels may be varied anywhere over the range of -5.0 to +5.0V. The output stage is capable of peak currents of up to 2.0A, depending on the supply voltages used and Typical Application Circuit +100V +12V +12V 1.0F 0.47F 0.47F VDD VH 10nF OE INA OUTA 10nF -100V 1.0F INB TC6320 OUTB 3.3V CMOS Logic Inputs +10V OUTC INC OUTD IND 1.0F 10nF GND VSS VL MD1810 10nF -10V TC6320 Supertex inc. 1.0F 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com MD1810 Ordering Information 16-Lead QFN 4.00x4.00mm body 1.00mm height (max) 0.65mm pitch Device MD1810 MD1810K6-G -G indicates package is RoHS compliant (`Green') Absolute Maximum Ratings Parameter Value VDD -VSS, Logic supply voltage 16 -0.5V to +13.5V VH, Output high supply voltage VL - 0.5V to VDD +0.5V VL, Output low supply voltage VSS - 0.5V to VH+0.5V VSS, Low side supply voltage 1 -7.0V to +0.5V Logic input levels VSS - 0.5V to GND +7V Maximum junction temperature +125C Storage temperature -65C to 150C Operating temperature -20C to +85C Package power dissipation 2.2W Thermal resistance (JA)* 16-Lead QFN (K6) (top view) Product Marking 45C/W Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. * 1.0oz 4-layer 3x4" PCB Y = Last Digit of Year Sealed W = Code for Week Sealed L = Lot Number = "Green" Packaging 1810 YWLL Package may or may not include the following marks: Si or 16-Lead QFN (K6) DC Electrical Characteristics (V H Sym Pin Configuration = VDD = 12V, VL = VSS = GND = 0V, VOE = 3.3V, TA = 25C) Parameter Min Typ Max Units Logic supply voltage 4.5 - 13 V 2.5V VDD 13V VSS Low side supply voltage -5.5 - 0 V --- VH Output high supply voltage VSS +2 - VDD V --- VL Output low supply voltage VSS - VDD -2 V --- VDD - VSS IDDQ VDD quiescent current - 0.8 - mA IHQ VH quiescent current - - 10 A IDD VDD average current - 7.0 - mA IH VH average current - 18 - mA VIH Input logic voltage high VOE -0.3 - 5.0 V VIL Input logic voltage low 0 - 0.3 V IIH Input logic current high - 1.0 A IIL Input logic current low - - 1.0 A VIH OE input logic voltage high 1.7 - 5.0 V VIL OE input logic voltage low 0 - 0.3 V RIN Input logic impedance to GND 10 20 30 K CIN Logic input capacitance - 5.0 10 pF Supertex inc. Conditions No input transitions, OE = 1 One channel on at 5.0Mhz, No load For logic inputs INA, INB, INC, and IND For logic input OE --- 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 2 MD1810 DC Electrical Characteristics (cont.) (V H Sym Parameter RSINK = VDD = 12V, VL = VSS = GND = 0V, VOE = 3.3V, TA = 25C) Min Typ Max Units Conditions Output sink resistance - - 12.5 ISINK = 50mA RSOURCE Output source resistance - - 12.5 ISOURCE = 50mA ISINK Peak output sink current - 2.0 - A --- Peak output source current - 2.0 - A --- ISOURCE AC Electrical Characteristics (V H Sym tirf tPLH tPHL Parameter Input or OE rise & fall time Propagation delay when output is from low to high Propagation delay when output is from high to low = VDD = 12V, VL = VSS = GND = 0V, VOE = 3.3V, TA = 25C) Min Typ Max Units - - 10 ns - 7.0 - ns - 7.0 - ns tr Output rise time - 6.0 - ns tf Output fall time - 6.0 - ns Rise and fall time matching - 1.0 - Propagation low to high and high to low matching - 1.0 - Propagation delay matching - 2.0 - - 200 - - 9.0 - l tr - tf l l tPLH-tPHL l tdm tOE_ON tOE_OFF Output enable time Conditions Logic input edge speed requirement CLOAD = 1000pF, see timing diagram Input signal rise/fall time 2.0ns ns For each channel ns Device to device delay match ns --- Logic Truth Table Logic Inputs Output OE IN H L VL H H VH L X High Z Timing Diagram VTH / VOE Curve 3.3V INPUT 50% 50% tPLH tPHL 12V 0V VOE/2 2.0 0V OUTPUT VTH vs VOE 90% 1.5 VTH 90% 1.0 10% 10% tr tf 0.6V 0.5 0 0 1.0 2.0 3.0 4.0 5.0 VOE Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 3 MD1810 Simplified Block Diagram VDD VH OE INA OUTA INB OUTB INC OUTC IND OUTD MD1810 GND VSS VL Detailed Block Diagram VDD OE VH Level Shifter VSS OUTA VDD INA Level Shifter VSS VDD VL VH VSS OUTB VDD INB Level Shifter VSS VL VDD VH VSS OUTC VDD INC Level Shifter VSS VL VH VDD VSS OUTD VDD IND Level Shifter SUB GND Supertex inc. VSS VL 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 4 MD1810 Typical Applications 2-Channel +100V to -100V Pulser +100V +12V +12V 0.1F 0.47F 0.47F VDD 10nF VH To Piezoelectric Transducer OE INA OUTA OUTB INB 3.3V CMOS Logic Inputs 10nF -100V OUTC INC 0.1F Supertex TC6320TG +100V 0.1F OUTD IND 10nF To Piezoelectric Transducer GND VSS VL Supertex MD1810 10nF -100V 0.1F Supertex TC6320TG Single Channel 100V to 0V Pulser +100V +5.0V +5.0V 0.1F 0.47F 0.47F VDD 10nF VH To Piezoelectric Transducer OE INA OUTA INB OUTB 3.3V CMOS Logic Inputs INC Supertex TC6320 0.1F OUTD GND VSS VL 0.47F Supertex inc. -100V OUTC IND -5.0V 10nF Supertex MD1810 -5.0V 0.47F Supertex TC2320 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 5 MD1810 Application Information For proper operation of the MD1810, low inductance bypass capacitors should be used on the various supply pins. The GND pin should be connected to the logic ground. The INA, INB INC, IND, and OE pins should be connected to a logic source with a swing of GND to OE, where OE is 1.8 to 5.0 V. Good trace practices should be followed corresponding to the desired operating speed. The internal circuitry of the MD1810 is capable of operating up to 100MHz, with the primary speed limitation being the loading effects of the load capacitance. Because of this speed and the high transient currents that result with capacitive loads, the bypass capacitors should be as close to the chip pins as possible. Unless the load specifically requires bipolar drive, the VSS, and VL pins should have low inductance feed-through connections directly to a ground plane. If these voltages are not zero, then they need bypass capacitors in a manner similar to the positive power supplies. The power connection VDD should have a ceramic bypass capacitor to the ground plane with short leads and decoupling components to prevent resonance in the power leads. The voltages of VH and VL decide the output signal levels. These two pins can draw fast transient currents of up to 2.0A, so they should be provided with an appropriate bypass Supertex inc. capacitor located next to the chip pins. A ceramic capacitor of up to 1.0F may be appropriate, with a series ferrite bead to prevent resonance in the power supply lead coming to the capacitor. Pay particular attention to minimizing trace lengths, current loop area and using sufficient trace width to reduce inductance. Surface mount components are highly recommended. Since the output impedance of this driver is very low, in some cases it may be desirable to add a small series resistance in series with the output signal to obtain better waveform transitions at the load terminals. This will of course reduce the output voltage slew rate at the terminals of a capacitive load. Pay particular attention that parasitic couplings are minimized from the output to the input signal terminals. The parasitic feedback may cause oscillations or spurious waveform shapes on the edges of signal transitions. Since the input operates with signals down to 1.8V even small coupled voltages may cause problems. Use of a solid ground plane and good power and signal layout practices will prevent this problem. Be careful that a circulating ground return current from a capacitive load cannot react with common inductance to cause noise voltages in the input logic circuitry. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 6 MD1810 Pin Description Pin # Function 1 INB Logic input. Input logic high will cause the output to swing to VH. Input logic low will cause the output to swing to VL. Keep all logic inputs low until IC powered up. 2 VL Supply voltage for N-channel output stage. 3 GND 4 VL Supply voltage for N-channel output stage. 5 INC 6 IND Logic input. Input logic high will cause the output to swing to VH. Input logic low will cause the output to swing to VL. Keep all logic inputs low until IC powered up. 7 VSS 8 OUTD 9 OUTC 10, 11 VH 12 OUTB 13 OUTA 14 VDD High side supply voltage. 15 INA Logic input. Input logic high will cause the output to swing to VH. Input logic low will cause the output to swing to VL. Keep all logic inputs low until IC powered up. 16 OE Output enable logic input. When OE is high, (VOE+VGND)/2 sets the threshold transition between logic level high and low. When OE is low, all outputs are at high impedance. Keep OE low until IC powered up. Substrate Supertex inc. Description Logic input ground reference. Low side supply voltage. VSS is also connected to the IC substrate. It is required to connect to the most negative potential of voltage supplies and powered-up first. Output drivers Supply voltage for P-channel output stage. Output drivers The IC substrate is internally connected to the thermal pad. Thermal pad and VSS must be connected externally. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 7 MD1810 16-Lead QFN Package Outline (K6) 4.00x4.00mm body, 1.00mm height (max), 0.65mm pitch D 16 D2 Note 1 (Index Area D/2 x E/2) 16 1 1 e Note 1 (Index Area D/2 x E/2) E E2 b Top View Bottom View View B Note 3 L A A3 A1 Seating Plane L1 Note 2 Side View View B Notes: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. 2. Depending on the method of manufacturing, a maximum of 0.15mm pullback (L1) may be present. 3. The inner tip of the lead may be either rounded or square. Symbol Dimension (mm) A A1 MIN 0.80 0.00 NOM 0.90 0.02 MAX 1.00 0.05 A3 0.20 REF b D D2 E E2 e 0.25 3.85* 2.50 3.85* 2.50 0.30 4.00 2.65 4.00 2.65 0.35 4.15* 2.80 4.15* 2.80 0.65 BSC L L1 0.00 0O 0.40 - - 0.50 0.15 14O 0.30 JEDEC Registration MO-220, Variation VGGC-2, Issue K, June 2006. * This dimension is not specified in the JEDEC drawing. This dimension differs from the JEDEC drawing. Drawings not to scale. Supertex Doc.#: DSPD-16QFNK64X4P065, Version C041009. (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www.supertex.com/packaging.html.) Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate "product liability indemnification insurance agreement." Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com) Supertex inc. (c)2012 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited. Doc.# DSFP-MD1810 C011612 8 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com