Drawing No. JGC40-3280 P. 1/12 Specification of Piezoelectric Ceramic Resonator CSALF12M0T55-B0 Approved by Date Checked by Issued by May 19, 2006 1. Scope ((R)) This product specification is applied to the piezoelectric ceramic resonator used for time base oscillator of a microcomputer. Please contact us before using any of the products in the applications not described above. 2. Part Number 2-1 : CSALF12M0T55-B0 Murata Part Number 2-2 : Customer's Part Number 2-3 : Customer's Drawing Number 3. Appearance and Dimensions 3-1 Appearance 3-2 Dimensions 3-3 No illegible marking. No visible dirt. 1 See Figure 1. : Leads are soldered on inside electrode and outer body is molded by resin. : : : : : Construction Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 2/12 4. Electrical Characteristics 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 Item Nominal Oscillating Frequency Initial Tolerance Resonant Impedance Insulation Resistance Withstanding Voltage Rated Working Voltage (1) D.C. Voltage (2) A.C. Voltage Frequency Shift by Temperature (-20+80) (-20C to +80C) Operating Temperature Range Storage Temperature Range Specification 12.000MHz 0.50% 0.50% max. 25 25max 500M (D.C.10V) 500Mmin. (Applied D.C. 10V) D.C. 100V, 5 D.C. 100V, 5 seconds max. D.C. 6V 15Vp-p. 0.5% 0.5%max. (from initial value) -20+80 -20C to +80C -55+85 -55C to +85C 0.5% (+25C60%R.H.,10) 0.5%max. (from initial value) Secular Change (Oscillation frequency for 10 years at 25C 60%R.H.) Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 3/12 5. Physical Characteristics Item 5-1 Random Drop 5-2 Vibration Resistance 5-3 Resistance to Soldering Heat 5-4 Solderability Specification After Test 1.0m 3 1 4-3 Components shall be measured after 3 times No visible damage and random dropping on the concrete floor from the the measured values height of 1.0m. shall meet Table 1 and 4-3. 1055Hz1.5mm 14-3 X,Y,Z32 Applying the vibration of amplitude 1.5mm and The measured values vibration frequency 10 to 55Hz in each of 3 shall meet Table 1 and perpendicular directions for 2 hours. 4-3. (1) +2605C 14-3 1.5 mm101.0 1 (2)+3505C 3.0 0.5 1 (1)Lead terminals are immersed up to 1.5mm The measured values from components body in soldering bath of shall meet Table 1 and +2605C for 101.0seconds, and then 4-3. components shall be left in natural condition for 1 hour. (2)Lead terminal is directly contacted with the tip of soldering iron of +3505C for 3.00.5 seconds, and then components shall be left in natural condition for 1 hour. LF (Sn-3Ag-0.5Cu 90% PCT+105C100%R.H. 4 5 +2455C30.5 LF Solder (Sn-3Ag-0.5Cu The solder shall coat at After being kept in pressure cooker at +105C least 90% of the temperature and 100%R.H. for 4 hours, surface of terminal. terminals of components shall be immersed in a soldering bath at temperature of +2455C for 30.5 seconds after being placed in a rosinmethanol for 5 seconds. Test Condition Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 5-5 Terminal Strength Terminal Pulling Terminal Bending 5-6 Washability P. 4/12 9.8N10 1 4-3 Force of 9.8N is applied to each lead in axial No visible damage and direction for 10 seconds. the measured values shall meet Table 1 and 4-3. 2mm 90 90 3 After lead terminals shall be fixed at 2mm from No Cutting off. resonator's body, they shall be folded up to 90 from their axial direction and folded back to -90, then folded back to their axial direction. The speed of fold shall be 3 seconds each. 2 1 4-3 See Table 2. No visible damage and the measured values shall meet Table 1 and 4-3. Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 5/12 6. Environmental Characteristics Item 6-1 Dry Heat (Storage) 6-2 Cold (Storage) 6-3 Humidity 6-4 Thermal Shock 6-5 Salt Mist Test Specification After Test +8521000 14-3 1 Components shall be left in a chamber The measured values (Temperature: +852C) for 1000 hours, then shall meet Table 1 and measured after leaving in natural condition for 1 4-3. hour. -5521000 14-3 1 Components shall be left in a chamber The measured values (Temperature: -552C) for 1000 hours, then shall meet Table 1 and measured after leaving in natural condition for 1 4-3. hour. +60290 +5 %R.H. 14-3 -0 10001 Components shall be left in a chamber (90 to The measured values 95%R.H. at +602C) 1000 hours, then shall meet Table 1 and measured after leaving in natural condition for 1 4-3. hour. -55C30 14-3 +85C30 110 1 After performing 10 cycles of thermal test (- The measured values 55C 30 minutes to +85C 30 minutes), shall meet Table 1 and components shall be left in natural condition for 4-3. 1 hour. +35251 48 1 1 4-3 Components shall be left in a chamber with There shall be no +352C, density of 51% (by weight) for 48 evidence of destructive hours, then measured after leaving in natural corrosion and the condition for 1 hour measured values shall meet Table 1 and 4-3. Test Condition Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 6-6 Sulfuration P. 6/12 1000ppm 24 1 1 4-3 Components shall be left in a chamber with No breakdown and the sulfur density of 1000ppm for 24 hours, then measured values shall measured after leaving in natural condition for 1 meet Table 1 and 4-3. hour. 1 Item Oscillating Frequency Table 1. Specification After Test 0.3% 0.3%max. (from initial value) Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 7/12 7. Test Circuit 7-1 Oscillating Frequency : 2 : See Figure 2. 7-2 : Equivalent Circuit Constants : Vector Impedance Analyzer HP4194A or Equivalent. 7-3 : +2536010%R.H. +5+3545 85%R.H. : Standard conditions for the measurement shall be +253C temperature and 6010%R.H. humidity. The measurement shall be performed at the temperature of +5 to 35C and the humidity of 45 to 85%R.H. unless otherwise the result is doubtful. Measuring Condition 8. Packaging Standard 500 Each minimum package unit of products (500 pcs) shall be in a carton box and it shall be clearly marked with part number, quantity and outgoing inspection number. Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 9. ! P. 8/12 Cautions 9-1 Limitation of Applications () Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. Aircraft equipment Aerospace equipment Undersea equipment Power plant control equipment Medical equipment Transportation equipment(vehicles, trains, ships, etc.) Traffic signal equipment Disaster prevention / crime prevention equipment Data-processing equipment Applications of similar complexity and/or with reliability requirements to the applications listed in the above 9-2 Fail-safe Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 9/12 10. Caution for Use 10-1 The component may be damaged if excess mechanical stress is applied. 10-2 Please do not apply excess mechanical stress to the component and terminals at soldering. 10-3 Conformal coating of the component is acceptable. However, the resin material, curing temperature, and other process conditions should be evaluated to confirm stable electrical characteristics are maintained. 10-4 Irregular or stop oscillation may occur under unmatched circuit conditions. Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 11. ! P. 10/12 Note: 11-1 Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 11-2 You are requested not to use our product deviating from this product specification. 11-3 1 Please return one duplicate of this product specification to us with your signature to acknowledge your receipt . in case of no return within three months from submission date, or if we receive order before the duplicate is returned, this product specification will be deemed to have been received by you. 11-4 We consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. Therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid. Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 11/12 1 Figure 1. Dimensions W (CSALF12M0T55-B0) 120 W H T : : : 10.0max. 10.0max. 5.0max. H 0.50.1 T 5.01.0 1.30.1 0.30.1 0.50.1 : : : Vender's Code EIAJ Monthly Code mm in mm 5.00.3 2 Figure 2. Test Circuit CERALOCK(R): CSALF12M0T55-B0 VDD Output IC:1/6 CD4069UBE x2 (RCA) Rf (To Frequency Counter) CERALOCK VDD:120.1V CL1:30pF1% CL2:30pF1% Rf:1M R CL1 CL2 Murata Manufacturing Co.,Ltd. Drawing No. JGC40-3280 P. 12/12 2 Table 2 Washability Cleaning Solvent (HCFC)IPA 750H100SFRW HCFC, Isopropanol, Tap water, Demineralized water Cleanthrough750H, Pine alpha 100S, Techno care FRW Item Condition (1) +6028kHz20W/L 1 Ultrasonic 1 minute max. in above solvent at +60C max. (Frequency : Wash 28kHz, Output : 20W/L) (2) (3) (4) 1. 2. 3. 4. Immersion Wash Shower or Rinse Wash Drying +605 5 minutes max. in above solvent at +60C max. +605 5 minutes max. in above solvent at +60C max. +8015 5 minutes max. by air blow at +80C max. Notice: In case of immersing in cleaning solvent, the temperature of component must be returned to room temperature after soldering. 10 Total washing time should be within 10 minutes. Please insure the component is thoroughly evaluated in your application circuit. The component may be damaged if it is washed with chlorine, petroleum or alkali cleaning solvent. Murata Manufacturing Co.,Ltd. NOTICE ON PRODUCT STORAGE Ref. No. Issue Date. :PPS30MR-001B :Aug. 23, 2005 (R) (R) Part Name MHz Band Ceramic Resonator ( MHz CERALOCK ) 1. 1. PRODUCT STORAGE CONDITION Please store the products in room where the temperature / humidity is stable. And avoid such places where there are large temperature changes. Please store the products under the following conditions : Temperature : - 10 to + 40 Humidity : 15 to 85 R. H. 2. 2. EXPIRE DATE ON STORAGE Expire date (Shelf life) of the products is 6 months after delivery under the conditions of a sealed and an unopened package. Please use the products within 6 months after delivery. If you store the products for a long time (more than 6 months), use carefully because the products may be degraded in the solderability and/or rusty. Please confirm solderability and characteristics for the products regularly. 3. 3. NOTICE ON PRODUCT STORAGE (1). (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality, and/or be degraded in the solderability due to the storage in a chemical atmosphere. (2). (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3). (3) Please do not store the products in the places such as: in a damp heated place, in a place where direct sunlight comes in, in place applying vibrations. (4). (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality, and/or be degraded in the solderability due to storage under the poor condition. 4. 4. OTHERS Please be sure to consult with our sales representative or engineer whenever and prior to using the products. Murata Manufacturing Co., Ltd.